Search Documents

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Feebrey CA, Duncan RA

The Ebor Volcano in northeastern New South Wales is an eroded example of a central-type intraplate volcanic-intrusive complex. It is of Miocene age (19-20 Ma) and has similarities to other central-type volcanoes in eastern Australia which may represent manifestations of sub-lithospheric hotspot activity. Thick lava flows are exposed around the Great Escarpment and are dominated by a tholeiitic basaltic suite, ranging from ol-tholeiite to qz-tholeiite to icelandite with ages of 19.2-19.6 Ma. On its western edge, the tholeiitic lava suite probably overlies remnants of basanite flows belonging to the Eocene (-48 Ma) Doughboy province, but elsewhere, minor alkaline basaltic lavas may be coeval with the tholeiitic suite. Several felsic bodies were emplaced into the volcano at -19.0-19.2 Ma and include subalkaline and peralkaline types. The Crescent Complex is a Miocene-age, strongly differentiated mafic to felsic intrusion in basement rocks and centrally located in pre-erosion reconstructions of the Ebor Volcano. It is interpreted to be a major feeder for the tholeiitic lavas based on age and composition. Evolution of the dominant tholeiitic suite proceeded from a parental ol-tholeiite magma, through qz-tholeiite, icelandite and small volumes of felsic rocks by fractionation of plagioclase, olivine, clinopyroxene and titanomagnetite, accompanied by enrichment of SiO2, F,FeO/MgO, alkalies and HFSE.

Jan 1, 1995

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

While sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. It is often left to personnel who do not fully appreciate the significance and importance of sampling. Yet sampling and sample processing are of vital importance. There is little point in making major capital investments in the latest analytical equipment and spending considerable time obtaining the best analytical precision, if the sample provided for analysis is seriously biased in the first place.

Jan 1, 1976

By Cocks T

The 15-year long debate between the industry, Government and Aboriginal people about the rights and wrongs of Land Rights, the right of Aboriginal people to control development on their land and the relationship between the parties, has been long and often bitter. It has so far been a war of words and often the truth has been the first casualty. This paper looks at the debate and presents the perspective of Aboriginal people, as well as looking at how the industry and Aboriginal people can work together for everyone's benefit. It addresses such matters as: ò why Aboriginal people believe they have the right to control development on their land; ò the perception that Aboriginal people are anti-development; ò the perception that Aboriginal land is 'locked-up'; and ò how companies can negotiate with Aboriginal people.

Jan 1, 1994

Geological hazards such as faulting, basement ridges, and zones of "thin" (

Jan 1, 1998

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

By G C. Reed, J M. Murray

During more than 100 years continuous mining of the lead-zinc orebody at Broken Hill, an immense amount of geological data has been collected about shear zones related to the orebody. The challenge to current mine geologists is to synthesise and interpret these data sets in a way that is applicable to production demands. Precise knowledge of the locations of major shear zones is important not only for the determination of ground conditions but also to develop an understanding of ore remobilisation along these structures. Traditionally, geological information has been collected from drill core and back and wall mapping underground, and interpreted on sections that are approximately 20 m apart. The recent introduction of MaptekÆs Vulcan software has enabled the shear zones to be modelled in three dimensions. The new three-dimensional shear models have been combined with seismic data from the Southern Cross area. The seismic data is collected from a microseismic monitoring system installed in the Pasminco Southern Operations in August 1996 (Rauert and Tully, 1998). The addition of seismic information to the shear zone models has led to a greater degree of certainty about the shear zone locations and has provided information about shear zones in areas yet to be drilled.

Jan 1, 2000

The Research Centres Program initiated by the Federal Government and supported by the mining industry has had a major impact on geoscience research and education during the past five years. Eight major university based-Geoscience Research Centres are currently supported by the Government, including four Key Centres of Teaching and Research and a further four Cooperative Research Centres (CRCs). The Research Centres Program has led to a concentration of high quality research and teaching in areas of demand and strategic importance creating strong university - industry linkages and a source of well trained and motivated graduates. Over the last decade Australia's reputation as a leader in mineral exploration and ore deposit research has grown substantially, in part because of the development of the Research Centres Program, and to increased collaboration and interaction between research groups and exploration geoscientists across the industry. During a period when ore deposit research activity has been decreasing in other countries (eg USA, Canada, Japan and most European countries), equivalent research activities in Australia have been increasing, within a well co-ordinated national framework. The future challenge for universities and the mining industry will be to maintain the momentum of the successful research centres in order for the centres to become self-funding over a six- to nine-year period.

Jan 1, 1996

Mount Isa Mines' Hilton Mine was brought into large-scale production in 1990/91 at a time of sharply falling metal prices. To ensure the operation's survival and eventual prosperity there was an urgent need to reduce operating costs and increase revenue. A target of a 40 per cent increase in productivity over five years was set. Strategies to obtain the required improvements were developed on the basis of greater involvement and increased contribution from the workforce, major changes to the mining methods and the development and application of new technology. This paper describes the organisational, operational and technological changes that have been implemented at Hilton and presents the results achieved to-date.

Jan 1, 1993

By Reeves I. And Farquhar J, Pearce S

The irregular shape of the Rosebery orebody, coupled with the inconsistencies in grade over short strike lengths, has meant stoping blocks have had to be small to combat dilution and stability problems. In the past, each lens was divided into regular block sizes and developed up to five years before production commenced. There were two major drawbacks to this practice; firstly, existing development deteriorated over time therefore requiring rehabilitation prior to production. Secondly, the pre-determined blocks could not be easily changed to incorporate changes in mining technology or economic circumstances. Bearing these problems in mind, it was evident that any new lens development had to be designed to allow maximum flexibility. The lens being currently developed is J lens. It represents approximately 50 per cent of the current reserves tonnes, and 65 per cent of the zinc metal. Its importance to the mine's future cannot be over emphasised. At its core the lens is up to 25 m thick at grades of over 30 per cent zinc. The practice of dividing the orebody into levels and sublevels, with consequent crowns was no longer acceptable because of restrictions in stope design and potential loss of ore. To assist in the development planning of J lens, a geostatistical block model was applied in long section to graphically represent the lens. Areas of high zinc concentration, as well as zones of uneconomic material were identified by using the model. This has meant that the development could he targeted, enabling stope delineation to occur in the lens without significant ore loss. Because of limited development resources, and the need to bring J lens on-line in the near future, the development strategy has had to focus on 'just-in-time' principles, rather than accessing the whole lens from bottom, and progressing upwards. Tight development schedules have required individual stoping block to be developed on such factors as grade and available tonnes rather than as a vertical sequence.

Jan 1, 1993

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:  TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By T J. McGavin

This paper examines the fire life systems implemented in two existing tunnels and discusses whether the standards used were appropriate. It focuses on the Terrace Tunnel as this upgrade and refurbishment is complete.The New Zealand Transport Agency (NZTA) manages six tunnels on the State Highway network with two of these built in the last seven years. The Terrace Tunnel, opened in 1978, was refurbished with modern fire life safety systems in 2010–2012. An interim upgrade of the Mt Victoria Tunnel, opened in 1931, was also carried out at this time.In present times, few existing tunnels have undergone significant upgrades and refurbishments. The Terrace Tunnel required: new power supplies, control buildings, lighting, wall panels and jet fans, a deluge system, emergency exit lights and way-finding lights, a public address (PA) system, a radio rebroadcast system, lane control sign (LCS) and variable message sign (VMS), an over-height detection system (OHD) and a new tunnel management system.In the absence of suitable guidelines, various standards were used to carry out the refurbishment. The Austroad Guide to Road Tunnels and AS4825 Tunnel Fire Safety, although designed for new tunnels and not specifically intended for existing tunnels, provided a framework. A multi-criteria assessment of risk (MCAT) was carried out to determine the systems to be provided.The Terrace Tunnel has perhaps set a benchmark for refurbishing existing tunnels as few projects of this type have been completed recently. This paper examines the process and the outcomes.CITATION:McGavin, T J, 2014. The refurbishment of the Terrace and Mt Victoria Tunnels, Wellington, New Zealand, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 87–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The history of the rail and mining industry in Queensland over the past century is inseparable. Indeed it was mining that led to the construction of the line west from Townsville and that shaped its current alignment. The discovery of gold at Charters Towers started construction of the Great Northern Railway west from Townsville in 1879, with completion to Charters Towers in 1882. The line was extended to Hughenden in 1887 and to Cloncurry in 1907 - driven by copper mines both to the south west and the north west of Cloncurry. The mining industryÆs association with funding the construction of rail lines to service their individual mines began in this area when the Hampden and Mount Elliot mine companies agreed to pay 50 per cent of the cost of the line from Cloncurry. The line to Selwyn was completed in 1910. Copper mining saw the construction of many other rail lines in the Cloncurry area in the 1910 - 20 period before copper prices slumped. Included in these lines were the Malbon to Duchess line and the line to Kajabbi and beyond.

Jan 1, 1998

Computational models are very useful for studying many of the physical mechanisms which can cause sample bias. Within such models we can predict the trajectories of all individual particles and thereby make observations which are not possible for physical systems. Physical mechanisms highlighted include congestion at the cutter aperture, particles bouncing over the cutter aperture, air drag on fine particles, waves of material being bulldozed off the belt by the upstream side of the body of square cutters, and particles being thrown by the leading edges of cross-belt cutter blades. Having identified relevant physical mechanisms for an existing cutter, we can estimate the extent to which they are likely to result in unequal representation of portions of a stream of material and thereby estimate the maximum likely sample bias.

Mar 1, 2010

A mineral exploration manager's prime function is to provide a frame- work within which new mine production can be achieved. As part of this framework, the manager should know his employerb future requirements, and should direct exploration towards those particular mineral commodities which indicate satisfactory growth in consumption and price. Selection of these commodities can be assisted by studies of world reserves, and long term trends in price and consumption. Exploration planning is most efficient with an assured and reasonably uniform supply of funds.

Jan 1, 1980

By B Clements, R Dunne, J Dioses, S Hart

In April 2003 plant upgrades in the æLow GradeÆ Cadia Hill circuit were undertaken in order to improve concentrate quality and metal recoveries from the flotation circuit. The major changes involved: circuit reconfiguration to allow all concentrates to be reground to less than 38 ¦m prior to final cleaning; increasing ball charge in the regrind mill to fully utilise all of the installed power; desliming of the cleaner scavenger concentrate to improve the circuit water balance; and the inclusion of a gravity concentrator in the regrind circuit to recover more free gold to bullion.Once the flotation circuit had stabilised under the new operating conditions concentrate launder modifications and increased froth crowding on the scavenger flotation cells permitted the introduction of stronger collectors without compromising concentrate quality or circuit stability.Twelve months on, the copper concentrate grade has increased by two per cent and metal recoveries increased by three per cent and seven per cent for copper and gold respectively. The project capital outlay of approximately $2.0 million has been repaid in less than three months. This paper will review the project from the design, construction and commissioning perspective as well as the subsequent debottlenecking exercise that was required to eventually yield the full benefits of this upgrade.

Jan 1, 2005

By Barnett DW

Financial risk analysis provides the tools to examine the uncertainty of capital decisions in new mining ventures. This paper explores the methodology by which financial risks can be studied and quantified. The most commonly used risk evaluation methods, such as sensitivity analysis and discount rate adjustment, are presented as an introduction to a more comprehensive discussion of stochastic methods of discounted cash flow analysis using Monte Carlo sampling. The discussion is illustrated with examples of a stochastic discounted cash flow. The advantages of Monte Carlo sampling in risk analysis are discussed together with its problems, particularly those originating from the correlation amongst the variables that determine the economic output of a mining venture, and the difficulties created by insufficient data, imperfect knowledge and complexity. The paper also surveys the most commonly used software used in risk analysis.

Jan 1, 1994

By Hayward SB

The Maragorik prospect is an example of high sulphidation, Cu/Au mineralisation occurring at a high level in the hydrothermal system. As extensive ash deposits blanket the region, controlled-source audio magneto-tellurics (CSAMT), in conjunct-ion with bulldozer trenching, have been used to delineate subsurface geology. Fluid upflow has occurred along EW structures dilated by rotation on the bounding major NW lineaments. Rising hydrothermal fluids have exploited permeable horizons in contact with the upflow structures. This lithological control is evident as ledges of silicification and peripheral clay alteration, at high levels in the system. As is typical of high sulphidation systems, a two phase fluid consists of an initial rapidly moving vapour-dominated phase, followed by a liquid-dominated phase. Much of the zoned and overprinted silica to clay alteration is developed from the vapour-dominated fluid. Mineral deposition occurs as a result of brecciation of the competent silic-ification by liquid phase fluids. Such mineralisation is of restricted volume in ledges proximal to the feeder structures.The style of alteration and mineralisation are indicative of a very low temperature and hence a high level system. Thus, although high sulphid-ation systems are inferred to develop from porphyry-related magmatic fluids, such a source at Maragorik is interpreted to be very deeply buried.

Jan 1, 1994

By M Ahmed

Reliable face support pressure is necessary for shield driven tunnels in cohesionless soils to prevent excessive ground movements. This paper presents experimental work on stability of a tunnel face using transparent soil models aiming to obtain magnitude of tunnel face minimum supporting pressure, failure pattern and extension of failed zone. A model tunnel was preinstalled in transparent soil which was supported at the face by means of water pressure. Tests were performed by reducing supporting pressure until collapse occurred. Model tests were sliced optically with laser sheet and images were captured for every decrement in tunnel supporting pressure. Later, these images were analysed by digital image correlation (DIC) and vector fi elds of incremental displacements were obtained. Values of minimum support pressures were given for different cover/diameter (C/D) ratios. Geometry of the failure zones depicted for different (C/D) values and appeared to be of chimney shape with a limited extension front of the face. A minimum support pressure was achieved with support pressures as low as 10 ± 1 per cent of the effective vertical stress at the tunnel axis. The stability of the tunnel face was related to the coefficient of active earth pressure with C/D ratio having a small effect on the magnitude of required pressure at collapse. In general, results of the study were in agreement with current knowledge of full-scale situations.

Mar 8, 2011