Search Documents

By B Reynolds

The process design for green- or brown-fields metallurgical plants typically starts with two fundamental elements: the detailed mass and energy balance and the plant flow availability. The detailed mass and energy balance is generally developed using process flow-sheet simulation software and represents the steady-state operation of the plant at normal operating conditions. The plant flow availability, also known as a range of other industry-specific terms such as ‘flow availability’ and ‘operating factor’, describes the ratio of plant production to the steady-state mass balance. These elements are then used together as the basis for equipment selection and design.Plant flow availability takes into account a myriad of production loss factors including planned and breakdown maintenance, feed availability and composition changes, variability in operational performance and the interaction of batch and continuous unit operations. The combined impact of these loss factors are complex and as such plant flow availability is usually derived using a top-down approach such as comparison to an existing operation, a group of similar operations or to an anecdotal ‘industry leading’ benchmark. These top-down approaches are fraught with risk however, as they cannot factor in changes to equipment selection, flow-sheet or plant operating philosophy, and can result in over-expenditure of scarce capital or shortfalls in plant production.The use of dynamic simulation to provide a bottom-up alternative to quantifying the plant flow availability in metallurgical plant design has been growing rapidly in recent years. It provides a technique to quantify the combined impact of the loss factors described here and a tool to support process design and equipment selection by facilitating a range of sensitivity and what-if analyses. This paper presents a case study of how dynamic simulation has recently been used to support the

Aug 8, 2011

By Waghorne E. P

The State Electricity Commission of Victoria is Australia's largest single coal producer. Approximately 19 Mt of coal will be produced in 1989 from the SEC V's newest mine, Loy Yang Open Cut (LYOC), which com- menced overburden stripping operation in October 1982. When the adja- cent Loy Yang Power Station is completed in the late 1990's, LYOC will supply between 35 to 45 Mt/a, depending on power station performance and demand of coal for non-power generation uses. LYOC has been a major challenge for the SECV. It is the biggest single open pit coal mining development undertaken in Australia, with a whole of life capital cost approaching A$1 billion. The mine has supplied a very rapidly growing demand for coal from the expanding power station while developing in breadth, length and depth. Coal demand has consistently been above the figures anticipated during the initial planning because of the substantially improved performance of the 500 MW units of the Loy Yang A Power Station. The superior performance of the LYOC and power station has generated additional electrical energy during the first 5 years of power station operation compared with the initial planning targets- at almost no additional capital cost. This has been a major benefit to the SECV. LYOC will continue to present major challenges for the SECV, particularly in achieving overburden removal and coal reserve targets as development of the open cut continues to full depth over the next 15 years.

Jan 1, 1989

By G Bournival, Y Saavedra Moreno, S Ata

Flotation frothers are heteropolar molecules that are preferentially adsorbed at the bubble interface to enhance the flotation performance by promoting the formation of small and stable bubbles. Frothers have different characteristics that can be used to classify them. A classification framework has been recently presented by Saavedra Moreno et al (2022) to classify non-ionic frothers by conducting a principal component analysis (PCA) and a hierarchical clustering analysis (HCA). However, for the purpose of the present research, only five frother characteristics, including molecular weight (MW), hydrophile–lipophile balance (HLB), critical coalescence concentration (CCC), the minimum Sauter mean diameter (DL), and foam stability index (DFI) were used in the PCA and HCA. All those characteristics were evaluated for a two-phase system in the absence of particles. Realising the important role that particles play in froth stability and behaviour, the effect of hydrophobic particles on the presented frother classification framework was investigated in this study. Four frothers with different characteristics, methyl isobutyl carbinol (MIBC), 1-pentanol, tri (propylene glycol) (TPG), and tri (propylene glycol) methyl ether (TPM), were chosen. The experiments were carried out in the presence and absence of silica particles esterified with 1-pentanol. It was evident that the results for 1-pentanol, TPM, MIBC, and TPG in the three-phase system agreed well with the frother classification presented for the two-phase system as frothers were clustered in the same groups. The findings from this research support the use of the frother classification system presented in two-phase system to select a specific frother for a particular application without the necessity of conducting laborious experiments in a three-phase system.

Aug 24, 2022

By Bell I. F

In 1985, ZC Mines (now Pasminco South) had been unprofitable for some years due to a combination of high operating costs, low metal prices, low head grade and an aging and inadequate mining infrastructure. However, the resource of metal in the ground was still of world class, even after some 80 years of mining. A major study, which was to be of two years duration, was therefore commenced to establish a practical and profitable long term mining strategy and to cost the infrastructure options needed for its support and thus form the justification for a capital expenditure program to take the mine profitably into the 21st century and its second century of operation. This paper discusses the rationale behind the methodology adopted and the nature of the results achieved in one aspect of the study - the determination of the mineable resource and the relationship between the head grade/quantity of the economically mineable resource and the variables of cut-off grade, cost structure, annual production rate and metal prices/exchange rates. The basis of the study was the designing of some 5000 scopes to mine out the entire resource for a range of cut- off grades and the assembly of the detailed physical data thus obtained in a stope-by-stope data base for financial and other analysis. Those scopes which were shown to be economically mineable were then scheduled for two optimum annual production/cut-off grade/metal price combinations to provide life-of-mine cost and value of production cash flows.

Jan 1, 1992

By B Besa, E K. Chanda

It has long been recognised that narrow vein mining needs innovative approaches to mine access and mining methods in order to improve the economics of this vital part of the mining industry. The mining equipment used currently requires large openings in narrow vein-type deposits making mining operations uneconomical. In view of this and other shortcomings of the current mining practices, a study was initiated to investigate the potential of using low profile electric loader with mounted conveyor in conjunction with the electric monorail haulage system (EMTS) to load and haul the blasted material, particularly in decline development and main haulages. Computer simulation based on the General Purpose Simulation System/Henrikson (GPSS/H) is used to model the system and evaluate its performance. The results are compared with those for conventional mining using trucks and loaders. The EMTS provides competitive haulage rates in substantially smaller excavations than is currently achievable. According to simulation results, the electric loader in conjunction with the EMTS had the same number of blasts as the conventional system and hence the same advance rate of 3.33 m per 12 hour shift. Furthermore, the total drill-blast-load-haul cycle time was less than the conventional system by one hour.CITATION:Besa, B and Chanda, E K, 2012. Evaluation of low profile electric loader in conjunction with electric monorail haulage system in narrow vein mining, in Proceedings Narrow Vein Mining 2012 , pp 221-228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By D Anderson, W Timms

"A geotechnical centrifuge can characterise and model the interaction of tailings and fluids over very long time periods by accelerating drainage and consolidation processes. This technology can be considered an environmental ‘time machine’ for designing and evaluating tailings storage projects and verifying numerical models. The Broadbent G-18 geotechnical centrifuge (2 m diameter, up to 875 rev/min) and associated equipment is a unique facility commissioned in 2011 at UNSW Australia for applied research in low-permeability materials such as mine tailings. Two centrifuge modules are available: the permeameter module for characterisation and physical modelling and the strongbox module for physical modelling.This paper presents examples of geotechnical centrifuge applications for the: consolidation of slurries and dewatering design of earthen barriers compatible with tailings chemistry prediction of contaminant mobility. The specifications and capability of the UNSW Australia geotechnical centrifuge and associated instrumentation is also presented, along with preliminary analysis of the confidence intervals associated with permeability testing of a set of samples of varying heterogeneity. Drainage velocity through a mine tailings sample increases linearly with g-level in the centrifuge permeameter until tailings consolidation occurs. Alternatively, geotechnical centrifuge experiments can be designed to limit consolidation so as to quantify permeability changes that may occur with geochemical interactions between fluids and mine tailings or earthen containments. Reactive solute transport through mine tailings can be simulated at realistic solid:liquid ratios when chemical equilibrium is maintained during geotechnical centrifuge testing. Carefully designed physical models of tailings disposal tested at accelerated gravity can therefore provide a realistic evaluation of tailings consolidation and drainage and the potential for subsurface migration of contaminants from mine tailings over long time periods.CITATION:Timms, W and Anderson, D, 2015. Geotechnical centrifuge technology for characterising the interaction of tailings and pore water over decadal time periods, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 247–252 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 27, 2015

By G Le Juge, K Waldock

The current suite of bulk mining explosives has been available to the industry for over 20 years. The flexibility and performance of ammonium nitrate based emulsion blend explosives were accepted by the mining industry in the early 1980s. These water resistant explosives rapidly displaced the water gels and slurries developed during the previous two decades. However, since the 1980s there has been no equivalent step change to the basic formulation or application of bulk explosives, although there has been a continuous process of refinement with respect to stability, handling characteristics and most significantly, cost. In the 1980s explosives supply contracts were awarded based on technical evaluations, usually accompanied by field trials. Technical personnel from both mining companies and explosives suppliers dominated the negotiations and there was a strong focus on explosive energy and blasting requirements. Today, explosives from alternative suppliers are difficult to differentiate on the basis of energy so the focus has shifted to aspects of service and price û bulk mining explosives are now largely treated as a commodity and the negotiations are dominated by commercial personnel. Commercial pressures from large mining companies have seen a substantial reduction in the real price of explosives. However, this has come at a cost. In order to reduce manufacturing costs, emulsion formulations have changed. In general they are not only cheaper, but also less energetic. Powder factors have had to increase to achieve the same blasting results, especially in hard ground. It is debatable whether the mining companies have achieved all of the economies they were seeking. This paper discusses these issues and argues that the mining industry would benefit from taking a more technically driven approach to meeting their blasting requirements. Recent trends towards more open contracts between the mining companies and their suppliers can be extended to explosives. To achieve this, mining companies will need to acquire sufficient technical knowledge to take a more pro-active approach to specify the characteristics of the explosives required to maximise the economic performance of their operations.

Jan 1, 2004

By Ward B

Central Colliery was developed to exploit large underground reserves in the German Creek lease. It was planned from the outset as a retreating longwall operation and is the first longwall mine in Queensland. Longwall mining is not new to Australia but all previous experience has been confined to the coalfields of New South Wales. There was no precedent for longwall extraction in the markedly different geological setting of the Bowen Basin in Central Queensland. Various investigations were thus carried out during the initial development of Central Colliery, prior to the installation of the longwall, to ascertain the geotechnical characteristics of the coal seam and the adjacent strata and to predict the performance of the heading and pillar design as mining proceeds to depth. Laboratory tests showed the coal to be weak with an unconfined compressive strength of 9.6 MN/m2. Site inspection and geophysical correlation revealed a shear zone and extensive intraformational shear planes in the seam. The latter were found to exert a controlling influence on rib reaction in the headings. This behaviour was predicted by finite element modelling of the development headings which indicated that mining induced stresses in the coal would be relieved by block movement of the ribs. A chain pillar width versus depth curve was established for yielding pillar design based on empirical and computational methods. This gave pillar widths from 25m to 48m over the proposed depth range of 150m to 300m. Finite element modelling of the 25m pillars chosen for the first gateroads confirmed the overall stability of the design but suggested that rib spall could be significant in the adjacent tailgate. (1) Chief Mining Engineer, Capricorn Coal Management Pty. Ltd., German Creek Mine, Queensland (2) Senior Engineering Geologist, Coal Division, The Shell Company of Australia Limited, Melbourne

Jan 1, 1986

By H Park, L Wang

Froth flotation is one of the most widely used beneficiation processes for fine and ultrafine coals and minerals. Maintaining optimal metallurgical performance in industrial flotation operation is still a challenging task owing to the lack of an effective tool to diagnose the flotation performance in realtime. For this purpose, a number of flotation performance monitoring systems with different working principles have been developed to provide instant feedback for process control and optimisation. In this paper, for the first time, five different flotation performance monitoring systems were systematically compared through an on-site trial in a coking coal flotation plant in Queensland, Australia. The monitoring systems were used to measure (i) gas holdup, (ii) overflowing froth velocity, (iii) overflowing froth height, (iv) air recovery and (v) drag force exerted by overflowing froth, in an industrial flotation column and the outputs of these systems were collected simultaneously at a wide range of operating conditions. For each monitoring system, the best regression model describing the correlation between the system output and the flotation performance was selected from various regression models (eg linear, quadratic, power-law and logarithmic) using the Akaike information criterion (AIC). A comparison of the coefficient of determination (R2 ), residual sum of squares (RSS) and measuring accuracy at 95 per cent confidence level of the best regression models of these monitoring systems suggested that the drag sensor outperformed the other systems at a wide range of flotation operating conditions. The superior performance of the drag sensor was attributed to its distinctive design that enabled intimate sensing of variation of the overflowing froth properties. Furthermore, the drag sensor had the ability to monitor feed ash content variation when the other operation variables were set almost constant.

Aug 24, 2022

By Grossi M, Baiden G

This paper describes a new mine backfill method based on a newly invented binder with several years of test results from laboratory and on- site applications. The new binder has several advantages over traditional Portland and slag cement binders. One tonne of the new binder can replace two to three tonne of Portland cement when used to consolidate backfill and can result in the same compressive strength within seven days. When comparing backfill slurries of the same pulp density, the new binder attains more volume of in-place backfill mass than Portland cement because of the high crystallisation of water, resulting in tightly filled stopes. The crystallisation of the water provides for less or no de- watering in the backfill stope and easier transportation of the backfill slurry. Pastefill performance can be achieved by using pulp densities typical of a hydraulic backfill and the new binder, all the while transporting with the same ease of hydraulic fill.

Jan 1, 1998

By R C. A Minnitt

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the fundamental sampling error (FSE), the duplicate sampling analysis (DSA) and the segregation fractionalised analysis (SFA) are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody is calibrated using the DSA and SFA methods and the results are compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to a power of 3. Gy’s formula is a theoretical formula applicable in the case when fragments are randomly collected one by one, which is obviously never the case. This is because the fragment shape factor (f) and the granulometric factor (g) were introduced to take care of this anomaly. More recent formulae, such as those suggested by François-Bongarçon and Lyman, are empirically based formula. A later modification of Gy’s formula raises dN to the power ? (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of ? (alpha) for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of alpha in the range 0.97 to 1.30. The average value for alpha is found to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry preference for 1.5. It is suggested that for low-grade gold bearing ores, the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the combined FSE plus the grouping and segregation error, now referred to as the short-term component of the quality fluctuation error (QFE1), greatly simplifies the characterisation of gold ores, which now only requires the calibration of K for a given mass and established fragment size. The implications for the heterogeneity test from the generalised equation are that provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.CITATION:Minnitt, R C A, 2017. A generalised form of Gy’s equation for gold ores – empirical evidence, in Proceedings Eighth World Conference on Sampling and Blending , pp 331–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The mining industry is quite often faced with declining selling prices for its products in the face of rising prices for the input cost resources that it uses. Blasting is a key activity within the mining system and has a vital role to play within the Mine to MillTM concept. It is therefore important that blasting makes a positive contribution to mine profit and productivity. There are several variables involved in considering the profitability and productivity of blasting. The rock types and structures, the bench height, the blast hole drill rig specifications, hole diameter, spacing and burden, explosive loading and initiation and blast size fragmentation. Productivity accounting is a methodology which is used elsewhere to give additional insights into the productivity and pricing factors that drive the financial performance of a business. Miners know intuitively that productivity and pricing influence costs and profit, but only with productivity accounting can the dollars involved be calculated. Drilling and blasting are part of a chain of unit operations in a mine. For an owner-miner, drilling and blasting would be considered as cost centres and a productivity accounting cost model approach would be relevant. On the other hand a contractor is likely to consider drilling and blasting as a profit centre, in which case a productivity accounting profit model approach would be appropriate. Both of these will be explained. The paper provides a basic outline of deterministic productivity accounting and demonstrates its application to blasting. Drilling and blasting data from a mine was obtained for a two-month period. The change in productivity and prices was calculated to obtain the dollar contributions from them towards the change in cost. It was determined that although there had been productivity dollar gains these were offset by larger pricing dollar losses, the net effect being that total drilling and blasting costs increased. The productivity accounting analysis gives the facts and the mine is in a position to establish priorities based on knowing the dollar contributions of each input used.

Jan 1, 2001

By Cunningham J. C

JUST prior to the war the Broken Hill South Ltd: raised, on the average, 6628 tons of ore per week, all of which was crushed and treated in the 4-section gravity mill and the slime flotation plant, for the recovery of lead concentrate carrying silver. The sandy residues from that treatment were railed to the treatment plant of the Amalgamated Zinc (De Bavay's) Ltd. for the recovery of zinc concentrate by flotation, on the joint account of both companies. Subsequent to that-since 1916-approximately 1000 tons of old dump slime were also treated weekly for the recovery of lead and silver as slime-lead concentrate.PLANT CAPACITYUnder this programme the Babcock and Wilcox boiler plant of 8 boilers was taxed to such an extent as to call for the installation of two additional boilers, each of 2690 sq. ft. of heating surface and 55 sq. ft. chain-grade area.The electric generators and the air compressors of the old powerplant were also loaded to their maximum capacity. In view of the fact that the old power-plant had been added to from time to time since 1901, and that further extension was notpossible, and as it was not, moreover, an economical arrangement, the whole question of power generation was reconsidered. The considerations that determined the installation of entirely new plant were as follows:(1) The need for more compressed air for underground work and more electric current for the extension of the slime-flotation plant for the recovery of zinc, as well as lead, as slime concentrates. Provision of additional power was also deemed advisable for the...

Jan 1, 1921

By B Manda, K L. Sandvik, K Musiwa

Mining and processing of pyrite ore at Iron Duke Mine, north east of Zimbabwe, generates large quantities of acidic mine water as a result of the oxidation of iron sulfides on exposure to air and water used in the drilling and blasting operations. The acid mine drainage (AMD) contains elevated levels of dissolved Fe, Al, Mn and sulfate and has characteristic pH values ranging from about 0.50 to 3.00. Handling and disposal of such a drainage places significant impacts on the economics of the mining operation due to the corrosive nature of the drainage on infrastructure, the limitations placed on water reuse and discharge to the environment under a new law governing effluent discharge. Treated sludge at Iron Duke is chemically unstable, changing pH from ~7 to ~3 within four days after deposition in the evaporation ponds. The effluent does not meet the permitted level of neutral pH, 500 mg/l sulfate and less than 2000 mg/l total dissolved solids. Excessive acid seepage from the evaporation ponds has resulted in contamination of the ground water below the ponds area, which shows high mean annual levels of iron (368.67 mg/l), sulfate (1702.89 mg/l) and low pH (2.86) in addition to other pollutants. This poor quality seepage infiltrates into the nearby Yellow Jacket River, contaminating the public water source. Furthermore, a deterioration of the land area and vegetation adjacent to the tailings dump is also observed. Understanding the controls on the neutralisation of acidic drainage and long-term sludge stability after placement in evaporation ponds is essential to minimise costs of closure requirements and for the protection of environment and human health. This study examined the effects of the master variables pH, redox potential, acidity and alkalinity on acid neutralisation. The results indicate that ferrous hydroxides are not as stable as ferric hydroxides and that proper oxidation of iron also leads to better sludge stability, higher treatment efficiency and a manageable sludge viscosity. Metal hydrolysis and secondary mineral formation at the evaporation ponds under a wide range of pH and redox conditions is responsible for equilibrium shifts in metal reactions, resulting in high potential for metal leaching and mobility. Mechanisms of metal attenuation are also discussed.

Jan 1, 2006

By M Ogle

"Booster fans are relatively rare in Australian coal mines. However, as mines become progressivelydeeper it is likely that such fans will be increasingly adopted as a method to sustain or improve the ventilation of underground workings. The reasons why booster fans may be an att ractive alternative include: increased cost of sinking additional ventilation shafts with greater seam depths; environmental objections to shaft sinking projects; and increasing urbanisation and surface constraints limiting availability of potential ventilation shaft sites. As Tahmoor Colliery movedinto its northern lease the ventilation constraints became the limiting factor on production. Thelimitations of the old workings meant that the existing ventilation system would be inadequateto sustain the required production. Extensive ventilation modelling was carried out to evaluatevarious potential solutions and the recommended option was the installation of a booster fanor fans, to gain underground access to an already approved shaft site in the northern lease.Proposals were sought from recognised fan manufacturers and various alternative arrangements were tendered. Ultimately the choice was between one large centrifugal fan and a set (three or four) of smaller æauxiliary-likeÆ fans in parallel. The successful tender was for a single centrifugal, an arrangement very similar to the booster fans that have been operating eff ectively at Westcliff Colliery for a number of years. This paper describes the current ventilation network, evaluation of the ventilation options, the fan selection process, and the project status to date."

Jun 1, 2012

By D Henderson, K Howie

In 2005, Glass Earth Limited (GEL) commissioned two large area detailed airborne geophysical programmes in the Taupo Volcanic Zone (TVZ). In the first survey Bell Geospace Ltd of Scotland conducted an Air-FTG« (airborne Full Tensor Gravity Gradiometry) survey covering 2338km2 at 300m line spacing. The second survey by UTS Geophysics, Australia included detailed airborne magnetic, radiometric and digital terrain data capture covering 5341km2 at 150m line spacing.   From the detailed geophysical data collected it is possible to identify major deeply penetrative crustal structures within the TVZ, as well as define subsurface geological features, such as intrusive bodies and alteration zones. These major deep crustal structures are thought to have a controlling influence on the distribution of epithermal gold mineralising systems, and along the corridors defined by these deep crustal zones, the chances of discovery of an economic epithermal gold discovery are greatly increased.   In this paper GEL gives some examples of the application of its integrated data driven approach to exploration in the TVZ at both regional and project scale. The paper focuses on how GEL identifies regional scale highly prospective deep crustal structures. Then, using the Horohoro epithermal gold system as an example, we show how GEL applies innovative geological and geophysical data processing to model and understand detailed subsurface geology, focusing subsequent exploration to ensure the best opportunity for a new economic epithermal gold discovery.

Jan 1, 2007

By R F. G Phelps

The former Gwynfynydd gold mine is located within the heart of the Snowdonia National Park, North Wales, United Kingdom. The black shale-hosted quartz reefs have intermittently produced more than 50 000 ounces of gold since 1863. Its most recent period of operation by Welsh Gold PLC was between 1992 and 1999 when it extracted 10 000 tonnes annually from a total resource base of 180 000 tonnes. A historical mining grade of 15 grammes/tonne was recovered from the Chidlaw Reef on which all production was based. Erratically distributed gold pockets hosted in the footwall zone of a 3 - 6 m wide quartz reef characterise the mineralisation. The gold exhibits a high-nugget effect and as a consequence the accurate determination of tonnage and grade was difficult. Production was undertaken by overhand shrinkage stoping. Due to its location within a National Park certain environmental constraints were placed on the operators. The principal requirement of planning permission was that processing should take place above ground and not involve chemicals. As a result, an underground mill based on physical separation methods was constructed in response to these environmental constraints. Much of the mine discharge is related to the flow of rainwater through the workings from surface openings on the reefs. Discharge from the underground milling facility was enhanced in various metals, particularly zinc, though was reduced to legally acceptable levels using liming tanks prior to discharge into the River Mawddach. The company was required to monitor and treat all water discharged from the mine before it reached the river. The mine closed in 1999, since which time a tip re-processing has continued as part of an environmental remediation and gold supply program.

Jan 1, 2002

By Dendyuk TV

The possible use of combined (flotation/magnetic separation and magnetic separation/flotation) technologies involving the new flotation reagent systems for upgrading the iron ore concentrates, low grade manganese products and beneficiation of graphite-bearing dusts from integrated iron-and-steel works has been shown. It has been found that the absence of magnetic flocculation phenomenon worsens the reverse cationic flotation of oxidised iron ore concentrates and direct flotation of low-grade manganese products which require the use of modifiers possessing the flocculating properties. The synergetic mixtures of polymers have been proposed to be used as modifiers, ie polyacrylamide (PAA) with carboxymethyl cellulose (CMC) and polyacrylamide with industrial lignosulphonates (LST)

Jan 1, 1993

By Upfold RW, Velzeboer MD

An underground mine fire will influence the ventilation equilibrium in several ways which results in a redistribution of the ventilating quantities and pressures throughout the whole mine. The ventilation carries the combustion products which constitute the greatest danger of mine fires through the mine and provides the oxygen on which the intensity of the fire depends. However, as a result of the ventilat- ion disturbances created by the fire, changes in airflow patterns can take place which are not always obvious, especially when the mine is being served by several fans. The use of com- puter simulation techniques allow for the likely effects to be tested and the different ventilation options to be evaluated as an integral part of the overall emergency/rescue planning and control procedures.

Jan 1, 1981

The deep seafloor in Papua New Guinea's proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994