Search Documents

By E Kabwe, M Karakus

Deep hard rock underground mines tend to experience high stress as such drives exhibit dynamic responses attributed to a rock burst variant (strainburst). This dynamic behaviour is difficult to predict, and every effort is made to devise the appropriate dynamic support system for its associated failure restraint. This paper outlines the back analysis and the support scheme design for an underground decline that exhibited damage from a dynamic strainburst occurrence. It employs a decline section that experienced a dynamically loaded strainburst that initiated rock fragment ejections. The procedure involves a preliminary structural analysis, a seismic intensity measure, and a rock mass simulation to determine the static stress concentration and ground support system response. The numerical simulation is conducted in FLAC3D which employs the advanced strain-softening IMASS constitutive model governed by two Hoek–Brown (HB) bounding yield surfaces. To account for the post-peak brittleness response associated with strainburst the plastic strain multiplier () is adjusted to 0.0 < < 1.0. The back-analysis shows that the occurrence was initiated by a low-intensity seismic wave that superimposed an extra stress component to the initial static stress which triggered rock fragment ejections. Additionally, the appropriate support scheme comprised of Weldmesh, Fibrecrete, static (split set) and yieldable (Kinloc) reinforcements is recommended and implemented. Thereafter, the bolt’s efficiency is evaluated based on the axial force and elongation capacities and then compared with the published bolt performance data. The evaluation results show that the maximum bolt axial force (0.1 per cent) and elongation (0.006 per cent) are below the designed capacity and rupture strain.

Nov 29, 2022

By T Muzondo, C Prins, D De Vaux, R Schouwstra

The Mogalakwena Platinum Mine in the northern limb of the Bushveld Complex is Anglo American PlatinumÆs only open cast operation exploiting the Platreef. The Platreef, which extends along the basal contact of the Bushveld Complex, is geologically and mineralogically a much more complex orebody than the Merensky and UG-2 reefs. Changes in the footwall and the genesis of the Platreef translate into a number of rock types being present. These rock types vary in hardness and recovery potential and present challenges to metallurgical staff trying to optimise the concentrator. A true understanding of the implications of treating these rock types is required if the maximum value from this orebody is to be obtained.In order to more accurately forecast production and incorporate ore variation in the mine plan and comminution and flotation circuits, a geometallurgical approach to managing the operation has been used and is being further developed.CITATION:Schouwstra, R, De Vaux, D, Muzondo, T and Prins, C, 2013. A geometallurgical approach at Anglo American PlatinumÆs Mogalakwena Operation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 85-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Y Potvin

Underground mines in Australia are progressively operating at greater depth, sometimes in conditions where mine induced stresses are very high. In such conditions, the seismic activity often becomes intense and violent and in response, mines must develop and implement a sound rock burst risk management strategy to continue operating safely.This paper discusses the latest techniques successfully used in Australian mines to mitigate the risk of rock bursts. In particular, the paper describes how the analysis of data collected from seismic monitoring systems can provide an understanding of the seismicity and be used for quantifying seismic hazards in the mine. Once an adequate understanding and assessment of seismic hazard has been achieved, the associated risk can be mitigated using different layers of protection.Strategically, modifying the mining method, the extraction sequence and/or the mining layout can alleviate the seismic hazard, but these solutions generally cannot be implemented rapidly. In the short-term, seismic risk can be mitigated tactically using an energy absorbing support system or to remove personnel from being exposed to rock burst damage by implementing exclusion zones.

Mar 21, 2011

A summary of the more important work by previous workers is followed by brief descriptions of the rock formations and regional structure. Type examples of the various forms of mineralization are described and the conclusion is drawn that there has been one main period of ore formation, namely, during the &quot;Viti Revolution&quot; in the mid or late Miocene.INTRODUCTIONThe Crown Colony of Fiji is comprised of a group of some 250 islands situated between latitude 160 sand 21 0 S and longitudes 1770 E and 1780 w: By far the greater, part of the total area, 7,083 sq. miles, is contained within the two main islands, Viti Levu 4,053 sq. miles, and Vanua Levu 2,128 sq. miles, and it is to these that most geologists have directed their studies. The most detailed work has been in the Tavua Basin, north coast of Viti Levu, centering about the mining town of Vatukoula and the geology of this area forms the subject of a separate paper by Blatchford (this volume p. 13).The present contribution summarizes geological knowledge of Fiji, at the time of writing (Feb. 1952), with particular reference to the known mineralIzation, but excluding the Tavua Basin. For general descriptions of Fiji&apos;s topography reference should be made to the recent works of Derrick and Dunkin.PREVIOUS WORKERSPeriod 1840-1930Prior to the gold rush of the early 1930s the visiting geologists concerned themselves in the main with the struc...

Jan 1, 1953

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

By K H. Esbensen

Optimisation of a real-time at-line monitoring system for control of industrial granule coating quality is presented. The system is based on a fluorescence imaging system, because fluorescence originates in the interiors of enzyme granules but is significantly quenched by a polymer coating (which is needed due to environmental precautions). We have developed an image analytical system for direct prediction of coating quality, which is based on application of the Angle Measure Technique (AMT) for image complexity characterisation; AMT is briefly described. The first part of the presentation addresses pixel sampling strategies within a digital industrial image, inherent in application of AMT, in which the unfolded image is regarded as a one-dimensional object in analogy with 1D process sampling in Theory of Sampling (TOS). The effects of random, stratified and systematic pixel selections in the unfolded image are evaluated. Also factors such as the fraction of image pixels and the effects of specific unfolding strategies (there are three principal strategies, termed æchopÆ, æsnakeÆ and æspiralÆ respectively) are investigated. It turns out that unsuspected artifacts are sometimes produced, related to the specifics of the unfolding procedure, which interferes with a straightforward 1D TOS process sampling analogy. These artifacts have a wider interest û among others, for 2D sampling û and therefore receive special attention in this presentation. The optimal pixel selection strategy for the AMT algorithm is found to be systematic or stratified sampling (not surprising according to TOS) of 500+ initiating points, but need to be unfolded in the novel spiral- or snake-wise fashions in order to effectively counteract these artifacts. This also has a general impact on various suggested standard schemes for 2D grid-sampling, among others, from the geoscience realms. The second part of the presentation is directed towards optimal image analytical sampling of a continuous series of fluorescent images (imaging of conveyor belts of æinfinite lengthÆ), ie optimisation of process image sampling. The minimum number of images needed to uphold a sufficiently good on-line estimate of the quality control (QC) parameter in question is found to correspond to the relatively high sampling rate of 15 - 20 per cent, which can be shown to be related to an intrinsic very high measurement error level (25 per cent) of a mandated analytical reference method.

Jan 1, 2005

By T Sparks

The Collie River catchment, located approximately 200 km south of Perth, covers an area of around 2830 km2 and is the source of run-off to the Wellington Dam, an important irrigation water resource for the Collie Irrigation District. The salinity of the Wellington Dam has increased due to historical clearing and irrigators currently use water with salinity levels approximately twice that of the Murray River in South Australia (Water and Rivers Commission, 2001). The Collie River Salinity Situation Statement (2001), released by the Water and Rivers Commission (now the Department of Water), identified realistic actions that could achieve the salinity reduction target. Subsequent benefit-cost analyses and prefeasibility studies recommended the diversion of the most saline flows in the Collie River away from the dam as an immediate intervention (URS, 2003). The East Branch of the Collie River above the locality of Buckingham (20 km east of Collie) contributes around half of the salt that flows into the Wellington Dam and the diversion and storage of the saltiest flows from the East Branch at Buckingham was identified as a viable option for reducing salinity in Wellington Dam. The proposal had one problem û the water could not be disposed of as quickly as it was diverted. However, in the vicinity of the diversion site were a number of coal mine voids and after preliminary discussions, the Government/Griffin Coal alliance was formed and from this the opportunities have continued. Diverted water would be stored temporarily in an adjacent mine void (Chicken Creek 4 void) and then disposed of to the sea. The disposal options included Western Power CorporationÆs saline discharge pipeline from Collie Power Station, or a new pipeline. The diverted water was also identified as a potential raw source for treatment and use in industry. This has opened up opportunities including desalination, water efficiencies in the power stations, increased reliability of water supply for the power stations, water for new industries, wastewater disposal options and extra water for PerthÆs water supply. In the process of solving the water storage problems the project introduced a range of mine water quality problems û heavy metals and pH û and the Department of Water (DoW) is now working with the mining industry and the Centre for Sustainable Mine Lakes (CSML) to develop treatment and management technologies. The project has received support and funding through the National Action Plan for Salinity and Water Quality (NAP) and it has been possible to accelerate and enhance this project as a result of NAP. The DoW has developed the proposal to an advanced stage and gained approvals for the capital diversion program to go ahead. The partnerships have expanded to include the second mining company, Premier Coal, the Water Corporation, Western Power and the Harvey Irrigation Cooperative. The proposal could feasibly result in a $90 million integrated water management initiative for Collie using the latest technology, mining operations and providing water for value adding industries in the local area. The DoW is not a mining company; however, our experience in managing water in times of shortage, environmental water quality criteria, competition for water and managing community expectations will have the same success factors:consultation and knowing your community and stakeholders, sharing issues and working in partnership can provide results far greater than the initial issue, even brackish water has value, every sector is in competition with each other and has to have a share of the water, an integrated approach can provide opportunities for development in areas of water shortage, and never think of water as wastewater.

Jan 1, 2006

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and&apos;reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

Corrosion affects the performance of rock support and reinforcement at various underground mines, including the George Fisher Mine, where recent studies showed that this risk to mining operations is generally not well understood. Corrosion reduces the capacity and life expectancy of ground support and generally is undetected unless the traditional destructive pull out test is employed to detect defect bolts. Where it is still acknowledged that the pull out test has still an important role to play in determining critical bond lengths for static and quasi static ground support designs, it does not provide an underground operation with any reassurance regarding its bolt&apos;s integrity, which has been compromised by in situ aggressive conditions. Non-destructive rock reinforcement calibration testing on single and twin strand cable bolts, rebar bolts and friction bolts at the George Fisher Mine enabled the testing team to detect bolts with compromised integrity in one area of the mine. The non-destructive rock reinforcement integrity testing conducted uses a complex &apos;Stress Wave Analysis&apos; package based on the processing of clear seismic signals imparted into the rock reinforcement element that is being tested. The seismic signals are processed by &apos;Fourier Transform&apos; into various criteria which can be used to produce models of the element such as mechanical admittance, frequency spectra and velocity which are all being used in the final modelling of the rock reinforcement element under analysis. This paper highlights the enormous potential to effectively manage the geotechnical risk that corrosion presents for an underground mining operation.

Nov 25, 2010

By G J. Lyman

The theory of sampling has progressed slowly over the last century. The concepts of correct sampling were known to mining engineers such as D W Brunton in the 19th century. It was recognised early in the 20th century that the Poisson distribution of particles carrying the target analyte was the key to the uncertainties between samples of a given mass. However, no efforts were made until the 1980s to determine the entire sampling distribution as a function of sample mass. The variance of sampling was made clear by Gy and others, but none attempted to determine the entire sample assay density function until J H Venter in South Africa applied the method of characteristic functions to the problem.Venter applied the method to a specific case of very low analyte concentrations in samples of very fine particle size where his assumption of constant sample mass was justified. When his general methodology is applied to the more general problem, it can be shown that the assumption of constant sample mass is no longer justified and leads to some anomalous results for sampling variance. Venter’s method can be expanded to allow for a statistically variable sample mass and to take into account the size distribution of particles that carry no analyte.This paper presents the basis of Venter’s work and shows how the approach can be easily modified to yield results for the variance that are consistent, for example, with the work of Gy. It is also demonstrated that the entire sampling distribution can be determined without undue computational burden when sufficient information on the material heterogeneity has been collected.CITATION:Lyman, G J, 2014. Determination of the complete sampling distribution for a particulate material, in Proceedings Sampling 2014 , pp 17–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By BTrubT M

In the roast-leach-electrolysis process for the production of zinc, iron contained in zinc concentrates is converted to zinc ferrite during roasting. At Canadian Electrolytic Zinc (CEZinc), the Outokumpu Conversion process is used to simultaneously leach zinc ferrite and precipitate the iron as jarosite. These simultaneous reactions, while providing good process stability, require a compromise between optimum conditions for maximum zinc extraction and efficient iron precipitation. An improved conversion process has been identified which can achieve >99 per cent zinc extraction and more efficient jarosite precipitation to residual iron concentrations of

Jan 1, 1993

By S Maritsa, E K. Chiw, S M. Masuka, ika, T Chisahwira

The challenges facing the iron and steel industry on a global scale include depletion of resources, excessive energy consumption and CO2 emissions. The demand for iron products in Zimbabwe is increasing due to massive infrastructural development like the expansion and improvement of mines, transportation systems and water reticulation systems. In Zimbabwe, cast iron is mainly produced from recycling scrap metals. However, there is currently a shortage of scrap, which has resulted in the vandalism of state-owned properties such as bus terminals and railway wagons and lines. Nevertheless, Zimbabwe is rich in limonite ores, which are idle, and it is the aim of this research that this ore be effectively used to produce feed for the blast furnace. The Blast furnace is still the dominant route for producing cast iron where sintering and coking processes are the main routes for preparing the Blast furnace feed. Sintering limonite ore fines produce a product of poor grade because of the high value of loss on ignition that has a negative impact on Blast furnace efficiency. Furthermore, the sinter plant and the coke making plant are a source of huge environmental pollutants. Since low-grade Zimbabwean coal fines are also available in abundance, they were used in the preparation of the composite materials ensuring maximum utilisation of this resource. Results showed that the limonite ore-carbon composite pellets sample with the binary basicity ratio (CaO/SiO2) of about 0.27 and coal addition of 2.5 wt per cent achieved above the minimum physical quality requirements for pellet of drop number of at least 4, a dry compression strength greater than 2.2 kg/pellet and an indurated compression strength greater than 250 kg/pellet. Limestone was used as the binder avoiding the addition of more impurities from bentonite since the limonite ore has a high SiO2 content of about 8.78 wt per cent.

Sep 18, 2023

By T Suwa, S Ishida, J Xue, S Fuchida, H Shimada, Y Aoki, C Tokoro

Pyrite depression with prolonged pre-conditioning treatment in high salinity water has attracted much of researchers’ interest in recent years considering the increased utilisation of multiple stage flotation, closed water circuits, clay minerals, and sea water in flotation plants. In this study, the role of calcium (Ca)/magnesium (Mg) precipitates in stabilising the dissociative ferric hydroxy-xanthate (FHX), and its effect on modifying the balance of hydrophobic/hydrophilic species on the pyrite surface were primarily investigated. The total amount of extractable Fe-bearing species on pyrite concentrates and tailings after floatability test was quantitively determined using ethylenediaminetetraacetic acid (EDTA) extraction tests combined with inductively coupled plasma optical emission spectroscopy (ICP-OES). A more evident accumulation of extracted-Fe in pyrite concentrates rather than it in pyrite tailings was observed at both pH 9 and 10.5 when pyrite was pre-conditioned in Ca/Mg-bearing solutions for 360 min. Fourier transform infrared (FTIR) spectroscopy showed the main xanthate derivatives changed from di-xanthogen (1155 cm-1 ) to FHX (1167 cm-1 ) on the oxidised pyrite samples that were preconditioned in Ca/Mg-bearing solutions. Scanning electron microscopy-energy dispersive spectrometry (SEM-EDS) suggested the preferential accumulation of FHX upon secondary Ca/Mg-bearing precipitates as reflected by the higher Fe/S ratio together with the decrease of O element herein after xanthate conditioning. Although the hydrophilic secondary Ca/Mg/Fe-bearing minerals on the pyrite surface generally deteriorate pyrite’s floatability, the upper section of these secondary hydrophilic aggregates is partially covered by FHX alongside with further multilayer-adsorbed di-xanthogen. The precipitated Ca/Mg-bearing precipitates promotes the immobilisation of dissociated FHX derived from the reaction among iron oxyhydroxides and xanthate anions upon the localised secondary Ca/Mg/Fe-bearing minerals via acid–base complexation. Therefore, this phenomenon alleviates the hydrophilic modification of secondary Ca/Mg/Fe-bearing minerals to pyrite considering the immobilised FHX upon localised precipitates shows a slight hydrophobicity, and meanwhile, the upper FHX benefits the multilayer adsorption of di-xanthogen via the interaction among their inner hydrophobic alkyl chains.

Aug 24, 2022

By J Arif, J Proffett

Copper and gold mineralisation at Batu Hijau is directly related to quartz veining and wall rock alteration that developed in close spatial and temporal association with multiple tonalite porphyry intrusions. To its advantage with respect to the study and better understanding of the evolution of the porphyry system, Batu Hijau has comparatively minor late alteration and mineralisation overprints. This paper summarises results of detailed geological logging, petrographic studies and geochemical analyses of diamond drill cores from the deeper sections of the Batu Hijau porphyry system (ie its roots). An&nbsp;EXTENDED ABSTRACT&nbsp;is available for download. A full-length paper was not&nbsp;prepared for this presentation.

Jan 1, 2008

By T Blenkinsop, A Jenkins, H Moore, L Fisher, N Oliver, J Cleverley, M Nugus, J McLellan, J Hill, N Brunacci

The 2 Moz Vogue mineral resource is a recent discovery at the Sunrise Dam gold mine (SDGM), lying approximately 600 m vertically below the Sunrise Dam open pit. Unlike most other lodes, which are dominated either by steep vein sets or shallow high-strain (shear) zones, it lies broadly in the hinge of a folded felsic porphyry body, where it cuts intermediate volcanic lavas and volcaniclastic rocks and is not specifically concentrated at a lithofacies contact. The mineralisation is controlled by a complex interplay of moderate to shallow, west-dipping high-strain zones that are transected by irregular and discontinuous high-grade, north-west-, north–south- and east–west-trending breccia sheets that initially caused problems with attempts to model broad domains. However, by combining the structural controls and styles with the distribution of gold, arsenic, sulfur and antimony, we have improved opportunities for scheduling, extracting and processing the most appropriate material considering the current mining and processing constraints.The early delineation process for the Vogue lode revealed a significant mineral resource for the SDGM, coupled with the recognition of some potentially difficult downstream implications for mining and processing. The ultimate success of mining at Vogue will be a consequence of combining standardised data collection and geological modelling techniques with the results of the novel innovative techniques applied at an early stage of the project.Innovation (in the truest sense) drives change and application to deliver efficient and effective outcomes. Initial data generation and interpretation in lodes above Vogue provided a sound geological model based on strong structural foundations, leading to ideas that could be tested and validated by stress inversion analysis and modelling simulations. Geomechanical modelling simulations, based on the structural analysis, then provided an insight into both the structural and fluid evolution of the system and highlighted target areas. This promoted support for deeper drilling and sampling, which lead to the discovery of Vogue.With additional data, the structural model for Vogue was re-engineered through combination with geochemical and hyperspectral analysis and detailed geological and geostatistical domaining. Initial poor results from metallurgical tests from a small batch sample refocused efforts to undertake mineral and chemical characterisation and profiling (geometallurgy) and combine this data with the composite geological-structural-geochemical model. The result is a conditional probability model for differentiating mineralised or waste domains, with direct outcomes for planning, drilling and mining.CITATION:Nugus, M, Oliver, N, Blenkinsop, T, Hill, J, McLellan, J, Cleverley, J, Fisher, L, Brunacci, N, Moore, H and Jenkins, A, 2014. Exploration and innovation – the discovery and evolution of the 2 Moz Vogue Gold Resource, Sunrise Dam Gold Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 323–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By B Olsson, B Reynolds, R Norman

An unprecedented growth in demand for coal exports has placed pressure on multi-user coal chains to guarantee that their capacity expansion projects will meet the required demand. These projects, however, are taking place in an increasingly complex commercial and technical environment - competing rail and coal terminal service providers as well as a myriad of competing mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing system complexity and integration has driven the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems, their sensitivity to uncertainty and the resultant capacity of the integrated system is the key to both maximising value and minimising risk.Recently, TSG has worked closely together with the Integrated Logistics Company and a number of key stakeholders in the Dalrymple Bay Coal Chain to develop independent system master plans. These master plans have provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. This paper provides an overview of the study and a comprehensive guide to the process required to effectively achieve valuable strategic insights in a challenging multi-user stakeholder environment.CITATION:Reynolds, B, Olsson, B and Norman, R, 2012. Using independent system simulation to mitigate risk in the Dalrymple Bay Coal Chain, in Proceedings Project Evaluation 2012 , pp 77-84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By S Gray

Based on the 2021 Volume 5 State of PlayTM mining survey of key executives and board members in the mining sector, the key responses to ‘Which of the following technologies will have the biggest impact on mining in the next 15 years?’, were ‘Sensing and Data’ followed by ‘AI and Analytics’. From the early 1970s it would have been unlikely to predict the level of sensing and automation introduced to the broad industrial sector. No better example is the automobile industry where the combination of technological advances and external drivers (such as emissions control) have driven an incredible rate of change. The introduction of sensing, data, AI, and automation in the mining industry is just ramping up. Until now our energy efficiency, environmental footprint, labour shortage, skills, and safety have not been challenged by stakeholders in the way we are seeing market forces develop today. In order to address these challenges, we need to look back to the automobile industry and learn their lessons to accelerate our application of digital capability, analysis, AI and automation This is critical, particularly as access to skilled human resources becomes more difficult. An example of how this can be achieved in a gold processing plant utilising the latest real-time sensing technologies is the ‘Carbon Scout’ developed by Curtin University, and OLGA developed by CSIRO, which are both online technologies, coupled together with Gekko’s ‘Neon’ digital platform to achieve a fully automated real-time gold processing system.

Aug 24, 2022

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By M M. Collisson

The Synthetic Rutile (SR) plant operations, North Capel, produce electrostatic precipitator (ESP) fume and kiln scrubber residue. Typically ESP contains about 18 per cent Ti, 13 per cent Fe, 0.5 per cent Mn, eight per cent Si, six per cent Al, 16 per cent C, 0.9 per cent Zn, 0.6 per cent Pb, 300 ppm As, 300 ppm Cr and 5 ppm Cd. These wastes are held in a storage dam together with neutralised acid effluent (AE) liquor. A project was initiated to treat the fume and produce a benign residue that could be delivered to landfill, reducing dam space storage. Plant AE, containing free acid (9 - 14 g/L), Fe (6 - 7 g/L) and Mn (1 g/L), was used to leach ESP. The degree of extraction achieved for various elements include about 20 per cent Zn, almost 50 per cent As, five per cent Al, 0.4 per cent Pb and 15 per cent Cd. Extraction was most effective at pH The residue from AE leaching still contained Pb. TCLP tests of the leach residue produced Pb extraction significantly higher than the 0.1 ppm stipulated by Class 2 landfill guidelines. Other elements (eg As, Cd, Cr) successfully met the limits. Further leaching of the residue with EDTA extracted up to 65 per cent of Pb content. TCLP tests on treated residue showed Pb leaching potential of Lead was removed from the leach circuit as the sulphate by acidification of EDTA leach liquor, allowing EDTA to be recycled. The study showed that one waste stream can be used to treat another and help reduce plant waste.

Jan 1, 2001