Search Documents

A record $18.7 billion worth of metals, non- metals and fuels was produced in the U.S. during 1962, according to a year-end estimate from the USBM. The 1962 total value, based on preliminary statistics compiled by the Bureau, was nearly $600 million more than in 1961. Most minerals gained both in value and volume of production during 1962 according to information collected by the Bureau. All mineral fuels except anthracite showed increases. Among nonmetallic minerals- other than fuels-gains exceeded losses by two to one. Metal production held steady as gains and losses balanced.

Jan 2, 1963

By L. Adler

The proper transfer of roof loads from props and bolts to ribs and pillars can result in appreciable savings. The author shows how to plan such load reduction in underground mines. For openings in bedded rocks, analyzed by simple beam theory, it has been shown that roof loads can be shifted from one support to another.&apos; This transfer is effected by controlling the relative deflection of adjacent supports. If this action is used to reduce loads in the props or bolts and increase them in the ribs or pillars, it could be productive of economies averaging 30 pct. Such savings can be realized by: 1) using smaller artifical supports such as props and bolts, and 2) increasing loads in the rib to induce eventual failure for longwall caving. Since the rib is relatively load-insensitive, it provides a natural load sink. However, caution must be used in applying such permissive deflections, for while the supports are being handled properly, the stresses in the roof itself are very sensitive to such manipulations.1 An underground opening overlain by a relatively thin immediate roof, and a thick main roof, is usually laid out as shown in Fig. 1. The total open span (T) between pillars or ribs is calculated on the basis of the main roof, and the secondary spans (L) on the basis of the immediate roof, so that a complete accounting of the existing loads is made. For this purpose the immediate roof is treated as a uniformly loaded continous beam, which is an indeterminate structure as shown in Fig. 2(A). The term systematic supports places the following two restrictions on the continuous beam: 1) Spans between all supports are equal: uniformity of spans. 2) Loads on all supports (excepting ribs) are equal: uniformity of supports. The usual mode of analysis of such a structure by beam theory is to divide it up into a series of simply supported beams with end moments as shown in Fig. 2(B)2 The problem now is to transfer a maximum roof load to the rib from the span immediately adjacent to it by permitting its support to deflect, and yet not fail the roof. Once this has been done, the load can be equalized on all other supports by permitting further degrees of relative deflection. It is necessary, therefore, to determine an expression for the constant load on each support, and the required deflections, in terms of properties of the roof. From Fig. 1: T/L0 = No and T/L = N [1] Where: T = allowable span of main roof, ft. (Calculated from S = Mc/l) S is allowable modulus of rupture, psi. M is maximum moment, lb-ft (in this case wT2/12). c is distance from neutral axis to extreme fiber, ft. I is moment of inertia with respect to the neutral axis, ft4. L,, = allowable span of immediate roof, ft (calculated as was T). L = actual span of immediate roof, ft. N0 and N are pure numbers where No < N and N is the integer just higher than Nu. For example: If T =100 ft and L0 - 15 ft 100 N0 =100/15= 6.667 . . .N= 7 L = T/N = 100/7 = 14.28 ft Consequently N = No + n where n is a positive fraction i.e.: 0< n < 1 Since from Eq. 1, T = NL = N0L0 Lo /L = N/No = N/N-n

Jan 1, 1961

By M. J. Mullikin, J. B. Conway

Equations capable of representing combined first -and second-stage creep behavior include the Andrade, Cottrell-Aytekin, Garofalo, and de Lacombe equations along with a third-degree polynomial in t1/3. Employing some recent high- temperature creep data for arc-cast tungsten the effectiveness of these expressions was evaluated. It was found that, in this instance, the most accurate representations were afforded by the third-degree polynomial in t1/3 and the de Lacombe equation. Also noted was the fact that the Andrade equation gave results just slightly inferior to those obtained with the third-degree polynomial, definitely better than those due to the Cottrell-Aytekin equation, and slightly superior to those furnished by the Garofalo equation. EXPRESSIONS designed to describe combined first -and second-stage creep behavior must possess certain specific characteristics. At time zero the equation must reduce to a strain value corresponding to the instantaneous deformation on loading. Then in the early moments following load application transient-creep behavior must be described to reflect a creep rate which constantly decreases with time. And finally at larger time values linear (or at least nearly linear) strain-time behavior must be accounted for to yield the steady state or minimum creep rate. Some equations, such as the one based on the parabolic creep law, yield fairly satisfactory results in transient analyses but are not effective at all when combined first- and second-stage data are to be analyzed. Other equations give equally accurate results in both instances although in general the complexity of the equation is slightly increased. For example the Andrade1 equation: has found fairly general application in expressing first-stage creep behavior. Furthermore the contribution of the exponential term becomes more and more prominent as the time increases and causes this equation to exhibit a point of inflection at large values of time. With a proper selection of equation constants the curve can be made fairly flat in the region of the inflection point indicating a desirable equation form for combined first- and second-stage creep analysis. Another equation form with the proper characteristic is that of Cottrell and Aytekin:2 e =a +bt1/3 +ct [2] Obviously as time increases the first derivative of this expression approaches a constant value to suggest application to combined first- and second-stage creep analysis. Similarly a third-degree polynomial in t1/3: e -a + bt1/3 + ct2/3 +dt [3] has the same characteristics. Expressions of this type have been shown3 to be very effective in the analysis of transient-creep behavior and the fact that the first derivative has the same characteristic as Eq. [2] suggests use in the combined analysis.

Jan 1, 1967

By E. Martinez

The effect of ultrasonic energy transmitted through a liquid on chrysotile asbestos was investigated. Ultrasonic energy was effective in fiberization of chrysotile crudes as well as standard grades of milled asbestos fibers. Treated samples of several grades of milled fibers had increased wet bulk volumes and decreased settling and filtration rates compared to untreated fibers. Ultrasonics may be a method for fiberization of chrysotile without decreasing length or use of chemical additives that alter surface properties. Cavitation of the liquid on the surface of fiber bundles is believed to be the cause of the fiberization. It was found that ultrasonic energy greatly increased the rate of precipitation of latex on asbestos. When chrysotile asbestos fibers require additional opening or fiberization, the usual method employed is some type of high speed impact or grinding to open the fibers and produce a larger surface area. These methods always cause some degradation in length due to breaking of fibers. In addition, the efficiency of mechanical methods decreases as the diameter of fiber bundles decreases. Chemical methods have been proposed and it is claimed that fiberization down to individual fibers of 200-300 A diam is possible with some wetting agents. However, large amounts of reagent are required, approximately EDWARD MARTINEZ is with Central Research Laboratories, American Smelting and Refining Co., South Plain-field, N.J. TP 63H226. Manuscript, Aug. 12, 1963. Discussion of this paper, submitted in duplicate prior to Mar. 15, 1964, will appear in SME Transactions, September 1964, and AIME Transactions, 1964, vol. 229. 50 pct of the weight of fiber treated, and some of the wetting agent remains on the surface of the chrysotile and cannot be removed by any solvent which does not destroy the asbestos.&apos; This investigation was directed at determining whether ultrasonic energy transmitted through a liquid would be effective in fiberizing chrysotile asbestos. Samples of asbestos crudes and commercially milled fibers were treated; settling and filtration rates of treated and untreated milled fibers were obtained. EQUIPMENT A Westinghouse Corp. ultrasonic cleaning system WEHH was used in this investigation. See Table I for a breakdown of this ultrasonic unit. RESULTS AND DISCUSSION Fiberization of Chrysotile Crudes: Samples of chrysotile crudes were pulled apart with tweezers so that coarse bundles of fiber approximately 1/16 in. in diam were obtained. The bundles were put into a bottle with 200 ml of methanol and the mixture placed into the ultrasonic tank for 30 min at a power output of 1200 w. The test was repeated using water instead of methanol. During the irradiation it was noted that the surfaces of the bundles were being fiberized. The liquid eventually became cloudy with dispersed solids. Fig. 1 is an electron micrograph of the fibers, some reduced to unit dimensions, and a fine material released by the ultrasonic energy. The platy particles in Fig. 1 were identified by electron diffraction and differential thermal analysis as brucite, Mg(OH)2, which must have been intergrown in the chrysotile crudes. Electron micrographs of bulk specimens of chrysotile have shown a fine material filling the interstices between tubular fibers.2,3 Electron diffraction patterns of the fine material collected after ultrasonic treatment indicate that it is amorphous. After decanting the solution, bundles of chrysotile remained somewhat decreased in diameter. Continuing the ultrasonic irradiation of the remaining material resulted in additional fiberization. The opening of the fibers occurred in both methanol and water. Cavitation of the liquid by the ultrasonic energy is undoubtedly responsible for the fiberization. When sound waves are transmitted through a liquid at a

Jan 1, 1963

Four years of intensive exploration effort by Newmont Mining Corp. came to a climax May 27 in Carlin, Nevada, when local, state and federal officials joined with company officers at a dedication ceremony saluting the start-up of the firm&apos;s wholly- owned subsidiary, Carlin Gold Mining Co. Before an invited audience at the plant site, Newmont&apos;s President Plato Malozemoff and Nevada&apos;s Senator Howard D. Cannon pushed a lever and watched the new melting furnace rotate until a brilliant orange-red stream of molten gold poured forth from its mouth. Two 1200-oz bricks of bullion were poured that day, and they are the first of many that will lift this mine into the number two slot among U.S. gold producers and fourth among all gold mines on the North American continent. Although Newmont Mining first entered the gold mining business in 1929 in Grass Valley, California, the Company had operated no gold producers since the well-known Government directive L208, issued in 1942, closed down U.S. gold mines for the duration of World War 11. Now it is back in the business in a big way-a $10 million mine and plant capable of producing 200,000 oz. per year. All the gold from the Carlin operations is earmarked for the U.S. Mint in San Francisco.

Jan 7, 1965

By Wallace E. Pratt

TO SERVE their primary function of balancing supply with demand. crude-oil prices must not only return full cost plus a reasonable earning to the efficient producer but they must also offer an additional reward to stimulate exploration sufficiently to maintain adequate reserves. High prices increase the volume and efficiency of exploration; low prig e- -Idle exploration. Over the last decade average prices for crude oil have been much lower than for the proceeding ten years, and lower even than the average over the life of industry. Under these circumstances no one should be surprised to learn that over this same recent period of discovery of new oil fields has also lagged and fallen below its average level for the previous decade. Crude oil prices have been too ion to support the required activity in wildcatting.

Jan 1, 1941

By K. Takahashi, I. Iwasaki

it is well known1 that racemic mixtures of optical isomers can be separated by passing their solutions through a column packed with r- or 1-quartz powder so that one of the isomers becomes adsorbed selectively on the asymmetric quartz surfaces. Although the natural occurrence of r- and 1-quartz is more or less equally distributed, some localities show enough deviations toward a higher proportion of l-quartz2 to suggest that optical isomerism might influence quartz flotation. Beta-amines have an asymmetric carbon atom, and therefore optical activity may be expected. Beta-amines are reported to behave quite differently from alpha-amines in the flotation upgrading of certain oxidized iron ores.3 It is of interest, for both practical and theoretical reasons, to determine whether or not optical isomerism plays a role in the amine flotation of quartz. In this article the results of Hallimond tube flotation tests and of adsorption measurements using d-beta-phenylisopropylamine on both r- and 1-quartz are compared. D-beta-phenylisopropylamine was chosen for the tests because it is commercially available in optical isomers. MATERIALS AND METHODS Brazilian quartz crystals were hand-sorted according to the difference in trigonal trapezohedral faces, and each crystal was further checked by the Airy&apos;s spiral.4 The respective crystals were then crushed, and the -150 + 200-mesh fractions were screened out for the Hallimond tube tests. The samples were cleaned by brief leaching with warm, dilute hydrochloric acid, and then by repeated rinsing with distilled water. In preparation for the adsorption measurements, they were then dry-ground in a pebble mill for several hours, washed a few times with distilled water, and finally dried in a vacuum desiccator. By means of the Krypton gas adsorption method, the specific surfaces of r- and 1-quartz samples were determined to be 27,700 and 19,800 sq cm per gm respectively, the difference being due mainly to the decantation procedure rather than to the inherent difference in their grindability. D-beta-phenylisopropylamine was the only collector used in the study. It was solubilized by neutralizing with 110% of the stoichiometric requirement of 0.1 N hydrochloric acid. The specific rotation of the d-beta-phenylisopropylamine was determined with a polari-meter using sodium D line to be, Although the d-beta-phenylis~prop~lamine showed absorption maxima in the wave length region of 250 to 270 millimicrons, due presumably to the phenyl group, these peaks were too sensitive to be used for colorimetric determination of the residual concentration in the adsorption measurements. The amine-picrate method, used in the colorimetric analysis of dodecylammonium chloride,&apos; was found to work satisfactorily for the d-beta-phenylisopropylamine. The adsorption densities were thus determined after equilibrating 40 gm of the ground quartz sample with 300 ml of solution by tumbling in separate glass-stoppered Erlenmeyer flasks for one hour. EXPERIMENTAL RESULTS Fig. 1 presents the adsorption densities of d-beta-phenylisopropylamine on the r- and 1-quarts in the pH range of 6 to 7.5. In agreement with data reported in the literature, the adsorption density of d-beta-phenylisopropylamine was slightly higher on the r-quartz than on the 1-quartz, although the difference was not as pronounced as one might expect from the capacity of r-quartz and 1-quartz to separate racemic

Jan 1, 1969

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

By E. B. Brauer, W. Hurst, J. D. Clark

Because of drilling, completion, and workover practices, the permeability around a wellbore generally is different from the permeability of the formation. The zone with the altered permeability is called "skin" and its effect on the pressure or flow behavior of the well is called "skin effect". Hawkinsl has shown that the radius and the permeability of this zone are related to the skin by: If the permeability in the skin zone is less than that of the formation, the skin is positive; if it is more than that of the formation, the skin is negative. If the two permeabilities are equal, s is zero; that is, there is no skin. Van Everdingen2 and Hurst3 have given mathematical solutions to the case of a zone of reduced permeability around the wellbore. This skin effect is illustrated in Fig. 1. They treat the positive skin as a zone of reduced permeability of infinitesimal thickness around the wellbore. When applied to a well with negative skin, however, their solutions lead to the calculated flowing well pressure which is smaller than the formation pressure, i.e., an injection situation. This is a physical contradiction. In this paper, it is shown that this mathematical difficulty can be overcome by assuming an effective wellbore radius larger than the actual wellbore. Existing solutions2"4 are modified to include the effect of an enlarged wellbore radius, and thus enable the engineer to deal with negative as well as positive skins. Theoretical Development Van Everdingen and Hurst,4 through the use of Laplace transformation, obtained the following expression for transient fluid influx into a wellbore: The values for QtD, reported extensively by van Everdingen and Hurst,4 are obtained from the following integral:

Jan 1, 1970

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling&apos;s work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman&apos;s experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman&apos;s plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By E. P. Abrahamson II

The effect of transition elements which form binary solid solution upon the recrystallization temperature of zirconium has been investigated. All additions raised the recrystallization temperature. A correlation is obtained between the logarithm of the rate of change of recrystallization temperature with atomic percent solute and the free atom ground state electron configuration of the solute element. ThE work of Abrahamson, et al., on dilute binary solid-solution alloys indicated a correlation between the free-atom ground state electron configuration of the solute and either the brittle-ductile transition or recrystallization temperature. These studies were carried out on bcc base materials. The implication is that the outer s and d electrons of the solute are the prime determinant of the absolute rate of change of recrystallization or transition temperature. Furthermore, the limit of linearity has been shown to be a function of solute electron configuration for recrystallization in iron and vanadium. To date no Complete systematic recrystallization study of dilute binary zirconium base alloys has been made. It is the purpose of this study to note whether the change in solvent structure from bcc to hcp will influence the correlation. It was also desired to learn more of the role of the electron configuration of the solvent on recrystallization temperature. PROCEDURE All alloys were made using 99.87 pct Zr with 0.01 Cr, 0.04 Fe, 0.006 Hf, 0.003 Mg, 0.003 Mn, 0.003 N, and 0.080 0 (132 BHN). The solute elements were 99.9 pct pure. According to the published binary phase diagrams6 and metallographic examinations at X750, all alloys used were solid solutions. The alloys were arc melted and remelted six times in the form of cubic 200-g buttons under an argon atmosphere. They were then hot pressed at 950°C to 0.450 in., upset pressed to 0.350 in., and annealed at 800°C for 1 hr. The specimens were then Blanchard ground to 0.250 in., removing 0.050 in. from each side. The grain size of the material at this stage was found to be 8000 100 grains per sq mm. The specimens were then cold rolled to 0.130 in. and cold pressed to 0.125 in., yielding 50 1 pct cold work. All alloys were then chemically analyzed for the principal addition. The interstitial contents remained at the values of the starting material when checked on random alloy specimens. The rolled sheet was cut into 6.75 by 0.25-in. lengths and heat treated in a gradient furnace for 1 hr. The gradient was 250o to 900°C over the 6-in. length, recorded continuously by six thermocouples resting on each specimen. Control was 3oC, accomplished at the hot end. The recrystallization temperature was determined metallographically using polarized light. The criterion chosen was the point on the specimen showing the first recrystallized grain at a constant magnification, X200. Specimens were repeated, and the agreement was found to be 3°C. RESULTS Three different pure zirconium specimens were tested, and the recrystallization temperature was

Jan 1, 1962

By F. C. Langenberg, J. Chipman

Jan 1, 1959

NEW MEMBERS The following list comprises the names of those persons who became members during the period Oct. 10, 1916 to Nov. 10, 1916. ANCHOR, HANS C., Supt., Dome Extension Mines Co., Ltd., South Porcupine, Ont., Canada. BABCOCK, EARLE J., Dean, College Of Min. Engrg., State Univ. Of N. Dak., Grand Forks, N. Dak. BIDDIS0N, P. McDONALD, Construction Engr., The Ohio Fuel Supply Co., 52 W. Gay St., Columbus, 0. BOISE, PAUL T., Asst. Mgr., Stimpson Equipment Co., Felt Bldg., Salt Lake City, Utah. BOURNE, RALPH H., Vice-Pres Whiting Foundry Equipment Co., Harvey, Ill. BROWN, EDWARD OTTO FORSTER, Min. Engr., 706-707 Salisbury House, London, E. C., England.

Jan 12, 1916

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,&apos; using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By H. E. Strauss

The time-to-fracture test has been applied to pure platinum and to two alloys of platinum under the special conditions of small cross-sectional area of the specimens and of a test temperature above the annealing temperature. While the results are similar in character to those secured with large specimens of steel at temperatures below the annealing temperatures, two differences are noted: (I) an upward inflection in the curves for log stress vs. log time for the alloys, and (2) a sharp break in the curve for log stress vs. log time for pure platinum when single crystals filled the wire. The experiments showed that: (I) platinum and 10 per cent rhodium-platinum maintained their strengths at IIOO°C. better than did to per cent iridium-platinum, and (2) the rhodium-platinum after a time exceeded the iridium-platinum in strength at IIOO°C. Platinum alloys in their service at high temperatures encounter conditions somewhat similar to those that exist in the usual form of the "time-to-fracture"l test with steel. This paper is intended primarily to present results obtained by a "time-to-fracture" test under conditions approximating actual service for platinum (at the temperature IIOO°C. under oxidizing conditions) with three materials, pure platinum (99.99 per cent), a platinum alloy with 10 per cent iridium, and a platinum alloy with 10 per cent rhodium. The experimental procedure differed from that previously used in this type of measurement in that the samples were of small diameter (0.010 in.), were fully annealed, and were tested at a temperature definitely above their annealing points (600°C., IOOO°C. and 1050°C., respectively, for 60 per cent cold reduction and 15 min. heating time2,3). The experimental arrangement was similar to that previously described,&apos; using as heating unit a small, horizontal, platinum-wound furnace, ½ by 12 in., maintained at constant temperature by an automatic controller. The samples were 0.010-in. wires, which had been annealed at 1200°C. by drawing them slowly through the furnace. The time-to-fracture was measured electrically. Elongation was not determined because of the difficulties inherent in the experimental arrangement. Life—that is, the time-to-fracture—was considered the important property in these first tests. No attempt was made to measure the reduction in area, but the types of fracture were noted qualitatively; in the text they are referred to as (I) the normal, plastic, or necked fracture, (2) the knife-edge fracture, and (3) the brittle or intercrystalline fratture with small reduction of area. Results for different constant applied stresses are plotted in Fig. I. In all cases at least two trials were made for each stress, although they cannot always be indicated separately on the curves. The breaking Stresses drop very rapidly to a small frat-286

Jan 1, 1943

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.&apos;-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors&apos; knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971

By G. R. St. Pierre, A. J. Wilhelem

In connection with the reduction of hematite or magnetite to metallic iron, it appeared desirable to study the rate of reduction of each oxide to the next lower oxide under conditions which excluded all other condensed phases. For this purpose, pellets of Fe,O,, Fe,O,, and oFeOo were prepared. A gas train for the preparation of Ar-Hz-H20 mixtures was employed to establish a continuous flow of a controlled atmosphere over a pellet suspended on a balance. In this manner the following individual reduction steps could be studied: For example, pellets of hematite were reduced solely to magnetite by adjusting the gas atmosphere such that it was oxidizing to wustite. In other words, the reaction was complete when the hematite pellet had been totally converted to magnetite. The pellets were prepared from Baker Chemical ferric oxide. The ferric oxide powder was moistened and handrolled. Air sintering at 950°C produced Fe,0, pellets with a density of 3.65 g per cm3. The pellets ranged in size from 0.6 to 1.2 cm diam. The magnetite and

Jan 1, 1962

By R. E. Hummel, J. W. Koger

IT is generally accepted that the martensitic start temperature (Ms) can be determined by resistivity measurements and is that temperature where the resistivity vs temperature curve on cooling first deviates from a straight line.1-4 Both Titchener and ever&apos; and pops5 have used resistivity measurements to follow the martensitic transformation in b1 Cu-Zn and ternary Cu-Zn-based b-phase alloys, respectively. Actually because of the nature of their measurements the temperature of minimum resistivity (M) was used by these authors to determine "Ms" . Also, due to experimental difficulties in detecting M, with resistivity measurements, Pops and Massalski 8 determined M, by optical microscopy. The present communication is concerned with high-precision, low-temperature resistivity measurements which reveal a definite M, temperature which differs from the temperature of minimum resistivity (M). It is also shown that M is merely the result of the geometry of the percent-transformation curve and the temperature coefficient of resistivity of the alloy. In other words, it will be demonstrated that M has no apparent significance (except that it denotes a temperature at which some percent of martensite can be detected in a given alloy). Alloy specimens were made by melting 99.999 pct Cu and 99.9999 pct Zn in sealed and evacuated quartz tubes and homogenizing them at 601PC for 300 hr. After the alloy was cold-rolled into foils suitable for resistivity measurements, it was quenched in ice water from 871PC. The chemical analysis showed a zinc content of 38.8 wt pct. The cooling rate during the martensite transformation was 1°C per min and was controlled with a thermistor. Electrical resistivity measurements were made using a K-3 type potentiometer; the reproducibility of the resistivity values was better than 0.03 pct. Temperatures were measured with a thermocouple to an accuracy of better than 0.2° C. Fig. 1 shows the resistivity vs temperature curves of the martensitic transformation in B1 Cu-Zn for both cooling and heating. The starting point of the martensitic transformation (M,) was taken as that

Jan 1, 1968

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By John D. Morgan, Sylvain J. Pirson

An instantaneous and continuous analysis of a mineral suspension should be of great value in controlling various mineral preparation processes. Described herein is a method of analysis based on the use of high-frequency alternating current, which, under certain restrictive conditions, could be of use. Theoretical Considerations In a suspension of conductive minerals, the electrical effect primarily responsible for the variations in electric conductivity is the capacitance. In Fig Ia, let an alternating voltage E be applied across two electrodes F and F&apos;, between which are two rows (S and T) of mineral particles, all of approximately the same size, immersed in a fluid. Let the number of rows of particles between the electrodes be R and the number of particles in each row be N. If A is the area of a particle, D is the distance separating two particles, and k is a constant depending on the fluid, the capacity, CO, of the particle system will be given by: KRA C°= ND Referring now to Fig Ib, let R, the number of rows, be held constant, but let N, the number of particles in each row (S and T), be increased X-fold. The capacity, C1, of

Jan 1, 1949