Search Documents

Jan 1, 1881

CONTENTS RUSSIA-R. C.-BECKSTROM 3 VENEZUELA-F. H. KAY 9 TRINIDAD-W. J. MlLLARD 20 RUMANIA-1. I. GARDESCU 26

Jan 1, 1932

By Robert B. Johnson

The refraction seismic method has been used as an indirect means of exploring for fluorspar in southern Illinois by the Illinois State Geological Survey. Use of the method has been restricted to those areas where mineralization is associated with faults, a restriction necessitated by the operating principles of the refraction method. The seismic data enable the interpreter to locate fault zones in the subsurface and, under ideal circumstances, to make estimates of dip direction and magnitude and vertical displacement provided the local stratigraphic units are known and are geophysically recognizable. In this instance, refraction seismic exploration has been successful in the surface mapping of well-developed faults, both simple and complex with which fluorspar may or may not be associated. However, less clear results have been obtained where faulting has been less severe and where there are numerous accompanying mineralized joints.

Jan 1, 1964

By J. H. Brophy, M. H. Kamdar, J. Wulff

A constitutional diagram for the Ta-W-Re alloy system is presented. Rhenium dissolves in the complete range of solid solutions between tungsten and tantalum up to 48 wt pct in tantalum 'to about 30 wt pct in tungsten. Intermediate x and u phases only are found. X-ray diffraction and fluorescence, metallography and melting-point measurements were employed. THE constitution diagram of ternary alloys of tungsten, tantalum, and rhenium for temperatures above 1000°C is reported in this paper. Alloys in this system rich in tantalum and tungsten are of interest for high-temperature applications, and those rich in rhenium for electronic applications. No ternary phase diagram appears to be available in the literature. The three-component binary diagrams have been previously established1-3 and the present ternary data are consistent with these. EXPERIMENTAL TECHNIQUES Commercially pure tantalum (99.7 pct), rhenium (99.99 pet), and tungsten (99.9 or 99.95 pct) powders were purchased from Fansteel Metallurgical Corp., Chase Brass and Copper Co., and Fansteel or Westinghouse Electric Corp., respectively. These powders were pressed without binder and arc-melted under helium. The preparatory and analytical techniques employed were identical to those used for the Ta-Re system investigation carried out in this laboratory.324 These included X-ray diffraction and metallographic phase identification, X-ray fluorescent and wet chemical analyses, solidus determinations and heat treatments in a resistance-heated tantalum-filament vacuum furnace. For microstructural examinations standard mechanical polishing techniques were used through diamond laps. Polished speciments of all compositions were etched by swabbing with 4 parts HI?, 4 parts HNO3, and 1 part H20. Since the microstruc-tures of alloys containing one or two phases closely resembled their counterparts in the respective binary systems, typical examples are omitted in this presentation. In all the alloys examined, it was possible to observe the number of phases present. Particularly when there were small amounts of one phase involved, it was possible to identify it only by a combined conclusion based on X-ray diffraction, position of an alloy in a composition series, and the phase rule. A total of 100 different alloy compositions was arc-melted and studied in the as-cast condition metallographically and by X-ray diffraction. Specimens of each of these compositions were heat-treated at 2680, 2530, and 2020°C for 1, 2, and 4 hr, respectively. Those which were treated at 2020 were given a preliminary homogenization treatment at 2500°C for 1 hr. Specimens of 25 alloys were heat-treated at 1200o C for 168 hr. Solidus temperature measurements were made by the detection of incipient melting in eighteen alloy compositions. The metallographic and X-ray diffraction results are summarized in Table I. Graphically, this information appears in the isothermal plots of Figs. 2 and 3. Within the accuracy of the experimental methods, two such plots are sufficient to locate these data, since the results for 1200°C were similar to 2020 and those at 2530 resembled 2680

Jan 1, 1962

Jan 1, 1963

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By Reno H. Sales

Our colleagues cannot in the future earn reputations and medals for achievements in milling and smelting ore and for successful management of mining companies, if some one doesn't keep finding and mining the ore to mill and smelt and to provide the basis for the good management. Good ore seems sometimes to be quite helpful to good management, and good ore is not as easy to find as it used to be. And there are still more reasons, why—when this honor had been decided upon and named for Mr. Daniel C. Jackling—it should be initially conferred on Reno H. Sales. . The terms of reference of the award are that it should be conferred upon an individual working in the fields of mining, geology, geophysics, who has made an outstanding contribution to the progress of technology in one or more of those fields. And in this initial year (the earlier years are the easiest) just that was done. I think I could get away with it amongst the old-timers of my generation if I say that this time they made the award to the individual, who made the outstanding contribution. But, as Al Smith used to say, "Let's look at the record." Really, the record is mixed up a little with extra-lateral litigation—the old-time "apex cases" under Section 2322 of the Revised Statutes. Reno Sales doesn't like such litigation, but there is little question that the urgency, generated by conflicting claims of intra-limital and extra-lateral rights, and consequent necessity for committing to records and maps the complications of Butte structure, did advance—and by several years—the first continuous, accurate, systematic, and scientific portrayal of the geological and mineralogical details of what is, after all, the most important and the most complicated copper district—at least in North America. Prior to Sales' time, some of the most eminent of geologists often waived details. One geologist took the judge to the window to show him the Rarus fault going through a notch in the Continental Divide. The entertaining testimony in the Bluebird litigation was as perfect in literary style as it was innocent of the criteria by which faulting and lack of continuity of vein structure are now recognized. At any rate, this need for an accurate record of structure was in the background—to whatever extent it was, or was not, the etiological agent—for formation of the Geological Department of the Amalgamated Copper Co. in and about the year 1900. Charles W. Goodale was at that time the head of the Boston & Montana, and John D. Ryan succeeded William Scallon as the president of Anaconda Copper Mining Co. in 1905. Horace V. Winchell, for years a specialist in extra-lateral litigation, was perhaps the man who at that date had the vision, the persuasive weight with the management, and the willingness to defend the idea of large current expenditures (as then viewed) for a complete and sys-

Jan 1, 1955

By H. D. Mellom

The direction of the optic or "C" axis of a uniaxial metal crystal can be found with the metallurgical polarizing microscope by examining two planes of section on the crystal. Complete orientation of the crystal can be determined if a twin crystal is common to both surfaces of section. Examination of Uniaxial Metals in Polarized Light-Rotation of a uniaxial crystal surface, properly prepared,' shows four extinction positions 90 deg apart, provided that the surface is not close to a basal section. One of these two extinction directions corresponds with the projection of the optic axis on the surface of section. This direction can be found if the 'sign of the rotationr2 for the metal is known. To find the direction of the optic axis, the crystal is rotated on the stage 45 deg from an extinction position. With a crystal of negative sign, to produce extinction the analyser must be rotated towards the optic axial direction and vice versa. All sections, other than basal, of a uniaxial crystal have the same sign of rotation and, since there is no change in sign with wave length, white light can be used for these measurements. U the sign of the rotation is not known the presumed direction of the optic axis can be determined assuming a positive sign. A third section cut normal to the presumed optic axis will show basal extinction if the assumption is correct. It is convenient to use the edge between the two planes of section as a fiducial direction common to both surfaces. The optic axis can be related to this direction. If the above measurements are repeated on the other plane of section and the angle between the two section planes measured, stereographic projection can be used to determine the orientation of the crystal optic axis. Determination of Complete Orientation—The complete orientation of a uniaxial crystal can be determined provided that a twin crystal is common to both surfaces of section, and the twin law is known. The orientation of the twin crystal optic axis can be determined in the same way as for the main crystal

Jan 1, 1962

By Sherwin F. Kelly

One of the most succinct and illuminating perspectives of the field of geophysical exploration to appear in recent years is an article by E. A. Eckhardt, in the magazine Geophysics for October 1949. Although his review covers the year 1948, many of the data presented are apropos to a review of 1949, and form a pertinent background for a consideration of current progress. He presents charts of the world-wide distribution of gravimeter and seismograph activity in oil exploration, which show that surveys in the United States accounted for practically 68%; of all gravity work and 80%; of all seismic activity. Canada ranked second, with a proportion of roughly 6%, in each case; South America accounted for about the same percentage of seismic work, and double that amount for gravity surveys. Within the United States, Texas and Louisiana were the scenes of the greatest activity, both claiming about 60% of all surveys by each method.

Jan 1, 1950

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

Bailey, Lewis Newton, Master Engineer, Senior Grade, 4th Regiment, U. S. Engineers, Headquarters Company, died of pneumonia at Camp Merritt, N. J., on April 30, 1918. Baird, Louis, Lieut., Royal Field Artillery, British Army, died on the battlefield in 1915. Cobeldick, William Morley, Royal Engineers, died from gas poisoning on October 7, 1915. Dougall, Ralph, killed in action. Evans, Alfred Winter, Lieut.-Col., New Zealand Rifle Brigade, D. S. 0., D. C. M., killed in action on October 12, 1917. Gorman, Thomas C., Lieut., Canadian Engineers, killed in France, Mar. 18, 1918. Hague, William, 1st Lieut., Engineer Officers' Reserve Corps, died in active service. Hall, William T., Capt., Royal Flying Corps, killed in action. Heine, Bernhardt E., Lieut., Aviation Service, killed at Fort Sill, Okla., Aug. 10, 1918. Irving, John Duer, Capt., 11th Engineers, A. E. F., died while on active service in France on July 26, 1918.

Jan 9, 1918

By H. C. Fowler, G. B. Shea

MODERN industry's incessant demands for increased operating efficiency and lower costs require that hazards attending all occupations be reduced to a minimum. Reduction of the inevitable losses that result from accidents and injury to the worker is one of the important economic problems confronting industry today and is the basis for the widespread safety movement. Dr. Charles E. Munroe, chief explosive chemist of the U. S. Bureau of Mines, is father of the statement, "The existence of a nuisance is evidence of an economic waste." This pointed expression of the internationally recognized scholar and explosives engineer has a direct relation to the prevention of accidents. Every injury and death in industry is a waste in human endeavor and a lessening of productive gain. Dr. Munroe has aptly paraphrased his previous summation with reference to wastes as follows: "A lost-time accident is evidence of an economic waste." That the economic waste entailed by occupational accidents is chargeable to industry is well substantiated by the fact that all but four states (Mississippi, South Carolina, Florida and Arkansas) now have workingmen's liability and compensation laws.

Jan 1, 1933

By C. C. Harris, A. Jowett, S. K. Ghosh

An equation derived from first-order kinetics and accounting for return from froth to pulp has correlated continuous flotation data. The concentration of floatable material in the pulp can be altered either by changing the feed concentration or the feed rate. The latter does not affect the flotation rate constant, the froth to pulp return constant, and the concentration of non-floatable material in both the pulp and concentrate. Both the return constant and the concentration of non-floatable material in the pulp are directly proportional to the feed concentration, while the concentration of non-floatable material in the concentrate is related to the feed concentration. The investigation of the froth flotation process by continuous test methods, previously used by Brown and smith,1 Jowett and Safvi2 and Jowett and West,3 is being continued. Recent tests, primarily concerned with flotation cell design, have yielded kinetic data suitable for testing an equation proposed by Arbiter and Harris4 which postulates that a flotation process is defined by two rate constants: 1) the rate constant for mass transfer from pulp to froth. Previous workers have regarded this as the flotation rate constant. 2) the rate constant for mass transfer from froth to pulp, which has previously been ignored. THEORY Under continuous flow conditions at the steady state in Fig. 1 the equation developed4 is Symbols are defined in Table I. The air-liquid ratio terms4 have been omitted, since they are substantially constant for a given set of conditions. Also, for a system operating at the steady state Vf and V, remain constant and Eq. 1 can be written: Cp/Cc=b'/a,+Qc/a' [2]

Jan 1, 1963

By A. Lawley S. Schuster

The tensile behavior of copper foils prepared from rolled bulk material has been studied over the thickness range 2 to 53 , and for a range of pain sizes. For foils of comparable grain size, having the cube texture and tested along (100), yield strength increases with decreasing foil thickness t below -26p, with a corresponding decrease in ductility. Deformation occurs in the form of localized slip clusters distributed throughout the gage section. To the extent that the tensile strength (10 to 18 kg mm-) is unaffected by foil thickness, and that the foils possess fair ductility, the stress-strain behavior resembles that of bulk material rather than that of whiskers or evaporated films of comparable dimensions. The dependence of yield strength o on foil thickness t below -26p is of the form: oy = oo + kt-1/2. Possible explanations for the stress increase are considered based on 1) the dependence of active dislocation source length on foil dimensions, 2) the locking of surface sources, or the blocking of mobile sources at the surface due to surface film. It is now well-established that filamentary whiskers of many materials show exceptionally high strength compared with bulk crystals.'-11 As the diameter of the whiskers decreases to -1, the observed fracture strength approaches, and in certain cases exceeds, the calculated shear stress for the nucleation of slip in a perfect crystal.' In general, the stress-strain curve is entirely elastic, with strains at fracture approaching 1 pct. Similarly, thin films12-24 of evaporated or electrodeposi-ted material have been shown to possess tensile strengths three to seven times that of bulk material, with total strains at fracture -1 to 2 pct. In the present study, attention has been directed to the room-temperature tensile behavior of thin foils of copper over the thickness range 2 to 53, prepared from rolled bulk material. Yield stress, ultimate tensile strength, elongation to fracture, and work-hardening behavior are measured as a function of grain size and foil thickness. Structurally such foils are superior to either evaporated or electrodeposited films, and in the recrystallized condition exhibit considerable ductility. Apart from preliminary work by Sumino and Yamamoto25 on the work-hardening behavior of rolled and recrystallized copper foils, no systematic tensile studies have been carried out on material of this form. EXPERIMENTAL PROCEDURE Tensile specimens were prepared from 99.995 pct purity rolled copper foils of thickness 2, 6, 12, 26, and 53, obtained from the Hamilton Watch Co., Lancaster, Pa. Irrespective of specimen shape, it is necessary to use tensile foils with edges free from notches or tears. To this end, any form of cutting operation was excluded, and the tensile foils prepared using a photoengraving process, the details of which are described elsewhere.26 Since tensile data are required under conditions of uni-axial stress, the specimen shape is extremely important. Ideally, the foil should be infinitely long, allowing a gradual taper from the grip area to the gage section; however, from a practical standpoint, long foils are easily damaged during testing. A modified tensile specimen was therefore selected having a parallel gage section 1.25 by 0.20 in. with a tapered shoulder section increasing to 0.5 in. at the grips, and an over-all length between grips of 4 in., Fig. 1. In practically all tests, these foils fractured within the parallel gage section. By approximating the foil contour (Fig. 1) to a hyperbola it is possible to analyze the stress distribution in the tensile foil using two-dimensional elasticity

Jan 1, 1964

By James C. M. Li, J. Weertman

James C. M. Li (United States Steel Covp.)—The author has discovered a single analytical relation between the minimum, or the steady-state, creep rate and the applied stress confirming a statement made earlier by orn" that such relation should exist and should reduce to the power law at low-stress levels and to the exponential law at high-stress levels. However, as pointed out by the author, all the available theories of creep are not adequate to explain such a single relation. Inspired by such a statement, I have made a suggestion concerning a possible explanation13 of the new relation. This is based on the concept that the rate-controlling step is the cooperative motion of a short dislocation segment. The nature of and the reason for the cooperation have been discussed13 as well as the reason why the motion of the dislocation could be controlled by the mobility of the short segments. A natural short segment has been proposed13 to be the node formed at the intersection of two dislocations. The reason why the node may contain only a few atoms has not been discussed and the application of the proposed model to all the metals and alloys reported in this paper has not been attempted. It seems appropriate to include these in this discussion. The model was partly inspired by the substructure recently observed in the electron microscope on creep specimens. One such example is shown in Fig. 48 in Darken's Campbell Memorial Lecture. The substructure is a collection of dislocation intersections and irregular networks. No pileups have ever been observed in such specimens. A closer look at the network indicates that one set of dislocations is more straight than the other set sug- gesting that the other set may be mobile in the plane of the net. Since, for the network to survive the creep deformation, some dislocation reaction has to take place at the intersection of the two sets of dislocations, the mobile dislocation, even if it can slip in the plane of the net, will have difficulty in moving at these intersections. To illustrate, an idealized network is shown in Fig. 9. The thin lines represent the set of dislocations which are mobile and can slip in the plane of the net except at the nodes which are formed at the intersection of the two sets of dislocations. The other set of dislocations, represented by the thick lines, may have a Burgers vector which is not parallel to the plane of the net, and therefore may be immobile. Because of this nonparallel Burgers vector, the Burgers vector of the node, which is avectorial sum of the Burgers vectors of the two sets of dislocations, will also be nonparallel to the plane of the net. Therefore, the node cannot slip in the plane of the net and the set of mobile dislocations will have to drag the node along as indicated in Fig. 9. Now the problem is how many atoms could be involved in the nodes. Exact calculation of the length of the node is a difficult task especially since the length should be a steady-state length and not an equilibrium length. An estimate of the equilibrium length can be made by balancing the line tension of all the dislocations. The results would be a small fraction of the length 1 between nodes as shown in Fig. 10. In some instances such a calculation shows that the node will not be formed. But, since the calculation is only approximate, it does not rule out the possibility of the formation of a short node. In other instances the equilibrium length of the node is an appreciable fraction of I. Such a node would

Jan 1, 1963

By N. R. Morrow, C. C. Harris

The experimental points which describe capillary pressure curves are determined at apparent equilibria which are observed after bydrodynamic flow has ceased. For most systems, the time required to obtain equalization of pressure throughout the discontinuous part of a phase is prohibitive. To permit experimental points to be described as equilibria, a model of capillary behavior is proposed where mass transfer is restricted to bulk fluid flow. Model capillary pressure curves follow if the path described by such points is independent of the rate at which the saturation was changed to attain a capillary pressure point. Aemodified suction potential technique is used to study cyclic relationships between capillary pressure and moisture content for a porous mass. The time taken to complete an experiment was greatly reduced by using small samples. INTRODUCTION Capillary retention of liquid by porous materials has been investigated in the fields of hydrology,l soil science,2 oil reservoir engineering,3 chemical engineering," soil mechanics,5 textiles: paper making: and building materials In studies of the immiscible displacement of one fluid by another within a porous bed, drainage columnsl and suction potential techniques2 have been used to obtain relationships between pressure deficiency and saturation (Fig. 1). Except where there is no hysteresis of contact angle and the solid is of simple geometry, such as a tube of uniform cross section, there is hysteresis in the relationship between capillary pressure and saturation.2 The relationship which has received most attention is displacement of fluid from an initially saturated bed (Fig. 1, Curve R2), the final condition being an irreducible minimum fluid saturation Swr. Imbibition (Fig. 1, Curve A), further desaturation (Fig. 1, Curve R), and intermediate scanning curves have been studied to a lesser but increasing extent.2 ,3,9-12 This paper first considers the nature of the experimental points tracing the capillary pressure curves with respect to the modes and rates of mass transfer which are operative during the course of measurement. There are clear indications that the experimental points which describe these curves are obtained at apparent equilibria which are observed when viscous fluid flow has ceased; and any further changes in the fluid distribution are the result of much slower mass transfer processes, such as diffusion. Unless stated otherwise, this discussion applies to a stable packing of equal, smooth, hydrophilic spheres supported by a suction plate5 with water as the wetting phase and air as the nonwetting phase. The discussion can also be applied, in many

Jan 1, 1966

Jan 1, 1967

By Roshan B. Bhappu, Zeki M. Dogan

Two magnesite ores containing 3.15% and 8.73% SiO2 and a calcined magnesite product assaying 2.6% Si02 were first reduced in size to -20 mesh by roll crushing. 'They were then treated dry on a high intensity magnetic separator to reduce their silica content by rejecting iron-stained silicate minerals in the magnetic fraction and obtaining marketable magnesite or calcined magnesite as a nonmagnetic product.

Jan 1, 1975