Search Documents

By Rajiv Kalra, Ji Jiangang

"This paper reviews the following aspects of the world’s largest manufactured Grinding Mill’s in terms of diameter and power, along with the world’s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia.1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG – 28MW AG mills including FEA and major components3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG – 2 x 7.8 MW Ball Mills4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM’s and clients in July 2009.5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site.6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies.7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives"

Jan 1, 2012

By C. Derek Martin

"Predicting the ground response for tunnels in weak shales remains challenging. Predicting the ground response is challenged by difficulties in characterising the material, and our ability to predict deformations that are driven by coupled hydromechanical processes, when this material yields. The techniques that are used for characterizing weak shales are reviewed, and three case histories are examined that demonstrate the behaviour of these weak rocks during tunnelling. A general framework is provided for assessing the squeezing potential for weak shales.1 INTRODUCTIONGeologically, shale is an argillaceous fine-grained sedimentary rock that forms from the compaction of silt and clay-size mineral particles commonly referred to as ""mud"". Because of this grain size, the material is generically classed as Mudstone (Figure 1). Shale is distinguished from other mudstones because it is made up of many thin layers (laminated) and readily splits into thin pieces along the laminations (fissile). While the geological classification of shale appears straightforward, the classification for engineering purposes is often confusing. Underwood (l967) provided the first description of shale that made the distinction between “soil-like” compaction shales and “rock-like ""cemented"" shales. He coined the term ‘clay shale’ to capture the characteristics of hard clay yet recognizing its origin as a shale. In this paper weak shale is synonymous with clay shale and have strengths that typically range from R1 to R2 (1 to 25 MPa). Characterising these materials draws on methods from both soil and rock mechanics."

Jan 1, 2015

By Takefumi Takuma, Masashi Nagano, Christopher DellAringa

Multiple agencies in Southern California are retrofitting and upgrading their levees to catch up with ever-advancing urbanization affecting the requirements for existing channels and levees in this seismically active zone. Pressed-in sheet piles have been specified on some of these projects to minimize noise and vibration problems associated with sheet pile installation. This paper will study three Southern California levee and sewer pipeline retrofit projects that utilized pressed-in sheet piles in hard soil conditions with N-values higher than 50. BACKGROUND Southern California is home to numerous drainage channels fortified with earthen levees. In spite of the region’s semi-arid climate with varying annual precipitation from year to year, winter storms can bring in heavy and continuous rainfall to the area which overwhelms the levees’ capacities at times. Some levees are running through densely populated areas with homes and other sensitive structures such as underground utilities and bridge piers. Conventional sheet pile driving utilizes either percussive or vibratory pile driving methods, both of which generate high levels of noise and vibration, causing nuisance and potential damage to nearby structures. On the other hand, the press-in piling method utilizes a hydraulic force to push piles into the ground, thus practically eliminating the noise and vibration issue. Although there are types of press-in piling systems mounted on tall leaders on large crawler-base machines, they are less frequently used due to its much larger size and more limited drivability than the type discussed hereunder. The other type of press-in machine sits on top of already installed piles and is anchored with its own weight and additional counter weight when starting off as shown in Figure 1. Once the first few piles are pressed in, the equipment grips on top of the installed piles and moves forward on its own as the pile installation progresses. See Figure 2. This method does not use a vibratory or percussive force to install piles.

Jan 1, 2018

By Michael A. Knott

Large lateral forces on bridge foundations due to extreme events such as vessel collisions, earthquakes, and wave forces on storm surges during hurricane events are often the controlling design condition for bridge foundations. A review of the American Association of State Highway and Transportation Officials (AASHTO) vessel collision analysis and design codes used in the United States for highway bridges will be presented. The paper includes the background and development of the AASHTO Guide Specification and Commentary for Vessel Collision Design of Highway Bridges (1991) and vessel collision provisions of the AASHTO LRFD Bridge Design Specifications (3rd Edition 2004 and the approved 2005 Interims). Experience in using the AASHTO codes will be discussed and observations on the adequacy and gaps, comparison with the European Standard Code, and recommendations for immediate and long term needs will be presented.

Jan 1, 2013

By E. D. Gardner

From the standpoint of tonnage and dollar value copper is the most important nonferrous metal mined in North America. The opening of copper mines has had an important bearing on the development and settlement of many sections of the continent. The prosperity of many of the mining States or provinces depends directly upon the copper-mining industry. Normally, about 35,000 men are employed in the copper mines, mills, and smelters of the United States. The United States is the most important producer of copper among the nations; more copper is mined in North America than in any other continent, and for many years the United States alone produced about half of the copper of the world. During the last 10 years increasing production in South America and Africa has reduced the relative importance of North America and the United States.

Jan 1, 1938

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By Kevin Whipkey

How is Improvement Being Achieved ? Section Equipment ?Mine Layout/Projections ? Work Schedule ? Maintenance ? Management

Jan 1, 2005

By L. M. Dyer

Various attempts have been made to build leadership and management expertise with little success. There are numerous reasons these attempts have failed. Three reasons, along with suggested solutions, will be explored: 1) lack of ownership of the development process by those affected; 2) lack of congruence of the development process used and the business strategies of the organization; and 3) a comprehensive development process. We will discuss a development model applied inside a smelter and refining complex over one year involving all levels of management. The process was credited with helping to substantially reduce cost and enable breakthroughs in production, quality and safety results.

Jan 1, 2000

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

Jan 1, 2000

Demand for primary aluminum ingot increased during February, and several producers temporarily suspended new bookings for ingot. Alcoa announced that it would restart a potline at its Warrick, IN aluminum smelter by April 1, 1979, increasing the operations of that plant to its full capacity of 290,000 tons per year. At the end of February, it was reported that Alcoa would reactivate two of the seven units at its idle Point Comfort, TX smelter in May 1979, increasing the company's annual capacity by about 60,000 tons.

Jan 1, 1979

Air tabling of zircon-rich non-conductor products containing quartz enables most of the fine quartz present to be rejected without a markedloss of zircon. The coarser quartz in the air table feed can be separated from the zircon by screening one or more air table products, the oversize products containing most of the quartz and little of the zircon. Air tabling, with or without screening, is more efficient than wet tabling alone for the removal of fine quartz, but not for the removal of coarse quartz. Practically all of the quartz can be separated from the zircon by using wet tabling in conjunction with hydraulic classification, or by using air tabling in conjunction with dry launder treatment, in which a degree of sizing takes place that is advantageous for subsequent air tabling.INTRODUCTIONBack-dune and inland beach sand deposits usually contain fine wind-blown quartz, and neither spiral nor wet table concentration, alone or in conjunction, makes a clean separation of heavy minerals from quartz. Many rutile plants recover rutile and zircon from a low-quartz, wet-table concentrates by means of magnetic and electrostatic separation; some rutile and zircon are lost in the table tailings. Other rutile plants, and two of the ilmenite plants in Western Australia, recover rutile or ilmenite respectively, from a spiral concentrate containing several per cent of quartz, and then subject the non-conductor product to an additionalgravity concentration process to separate the zircon from the quartz. Some zircon is lost in the additional gravity process, but all of the rutile or ilmenite in the spiral concentrate is, or should be, recovered as high-grade concentrate. The higher recovery of rutile or ilmenite by this treatment method is offset by the expense of drying part of the feed twice, as a wet process is usually used to separate the quartz...

Jan 1, 1962

1. Domestic Production and Use: In 1984, 12 companies operated 27 primary aluminum reduction plants, with 3 firms accounting for 57% of production. Washington, Oregon, and Montana accounted for 35% of the production; Indiana, Kentucky, Missouri, and Tennessee 25%; Alabama, Arkansas, Texas, South Carolina, and North Carolina 20%; other States 20%. Based on published producer prices, output of primary metal in 1984 was valued at $7.2 billion. Aluminum consumption by 25,000 firms was centered in the east-central United States. Packaging accounted for an estimated 35% of domestic consumption in 1984, transportation, 20%; building, 18%; electrical, 9%; consumer durables, 8%; and other uses, 10%.

Jan 1, 1985

The STATE MINERAL SUMMARIES publication provides estimated data and summaries of mineral activities at the State level for 1989. Most of the estimates are based on nine months data. These summaries have been prepared in cooperation with State geological surveys or related agencies. Individual State summaries are published separately as State Mineral Industry Surveys and copies can be obtained from the appropriate State Activities field office.

Jan 1, 1990

In presenting this paper the author has in view a twofold purpose. In the first place, it is intended to set forth for the benefit of practical mining men some account of the principles underlying the design of tungsten carbide rock bits in the hope that a knowledge of these principles will assist in the successful application of the bits to mine and quarry drilling. Secondly, by evoking discussion, and even controversy, it is hoped that manufacturers and users of these rock bits will be encouraged to contribute to the general knowledge of a subject which to date has been rather lacking in published literature. The author well appreciates that many of the conclusions drawn in this paper are highly controversial, but if the only result is to call forth contradictory testimony from other workers in this field, at least one of his purposes will have been achieved.An attempt will first be made to set forth and examine those characteristics which go to make up an efficient rock bit, and the main factors affecting these characteristics will be discussed. In a paper of this general nature, consideration of any particular aspect must necessarily be rather brief, and there is little opportunity for detailed presentation of test procedures and data. Thus, it has been found advisable' to confine discussion of some minor points to a simple statement of fact. However, an attempt has been made to support all major conclusions by reference...

Jan 1, 1950

By Rajiv Kalra

This paper reviews the following aspects of the world?s largest manufactured Grinding Mill?s in terms of diameter and power, along with the world?s biggest shop assembly and trial run of the mills delivered to Sino Iron Magnetite Project in Australia. 1. An overview of the basic flow sheet of the Sino Iron (Magnetite) Project located in Australia 2. An overview of in-house designed CITIC Heavy Industries 12.2 m (40ft) F x 11 m(36ft) LG ? 28MW AG mills including FEA and major components 3. In-house manufacturing at CITIC-HIC work in Luoyang China of all major components for 6 off Ø12.2 m(40ft) AG mills and 6 off Ø7.9 m(26ft) x 13.6 m(44.6ft) LG-2 x 7.8 MW Ball Mills 4. Major aspects of design and preparation of the biggest shop trial run of Ø7.9 m(26ft) x 13.6 m(44.6ft) LG Ball Mill witnessed by international EPCM?s and clients in July 2009. 5. Major aspects of one piece assembly of 1300 tonne rotating element of the Ø12.2 m(40ft) x 11 m(36ft) LG AG Mill and Ø7.9 m F (26) x 13.6 m(44.6ft) LG Ball Mill at the port of the export China and transport to Australian Port and then to site. 6. An insight to unique installation methods used for Ø12.2 m(40ft) and Ø7.9 m(26ft) rotating element lifting on the mill foundation in one piece assemblies. 7. CITIC Heavy Industries present capability for in house design and manufacture of Grinding Mills up to Ø13.7 m (45 ft) with 35 MW Gearless drives and Ø12.2 m(40ft) with 2 x 10 MW Geared Mill drives

Jan 1, 2012

By E. S. Yan, R. Graley

"The StackCell was developed to overcome the engineering and design challenges that are commonly associated with existing flotation technology such as pneumatic, self-aspirating cells, mechanical cells, and flotation columns. These challenges include high energy consumption, large floorspace requirements, and size. They are most evident when designing systems to process streams containing a high volumetric flow rate coupled with a significant float yield. Unlike many metalliferous and industrial mineral applications, fine coal flotation circuits are typically characterized by feed streams containing a low solids content (<5%, by weight) where up to 85% of the feed can report to the product launder. With input from major engineering houses and end-users, the Eriez Flotation Division (EFD) developed the StackCell technology with the goal of providing an additional flotation option for end-users. This technology was designed specifically to overcome these challenges by providing an efficient method of separation in terms of metallurgy, but also with respect to equipment size, energy consumption, and installed costs. Besides being placed in tandem with existing cells to provide cost-effective supplemental capacity, this technology can be installed in a stand-alone arrangement as recently demonstrated at Patriot Coal’s Kanawha Eagle preparation plant. This manuscript provides an understanding of the underlying fundamentals of this new technology and presents data from Kanawha Eagle in addition to other industrialscale installations.INTRODUCTIONOver the past decade, column flotation has continued to gain acceptance as an alternative method for recovering fine coal due to superior metallurgical performance as compared to mechanical flotation cells. This point has been proven on numerous occasions by comparison of plant flotation data with the release analysis separation curve (Dell et al., 1972). Data from a release analysis test approximates the ultimate flotation response of a coal sample. In North America, a number of investigations have been published that document bottom-line improvements achieved using column cells (Luttrell et al., 1999; Kohmuench et al., 2004; Baumgarth et al., 2005). According to these reports, the benefits are derived from an overall increase in plant yield that can be achieved due to the improved product grade in the flotation circuit. In particular, the application of wash water to a deep froth utilized in column flotation minimizes the nonselective recovery of high-ash ultrafines that are hydraulically entrained in the froth by conventional flotation machines."

Jan 1, 2013

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014