Search Documents

The dissolution of the naturally occurring mineral zircon (ZrSiO4) is examined after ball milling it with magnesium oxide for up to 100 hours in a laboratory mill. There was little effect on the solubility for the initial two hours where size reduction of the zircon was considered to be the dominant effect. Beyond two hours the dissolution increased as a function of the square root of milling time. X-ray diffraction of the powders did not reveal the identity of the soluble phase. However, a nanocrystalline phase was present after milling and this is thought to be the soluble phase.

Jan 1, 2000

By Jouko L. Lehtonen

Sheet pile walls can be sealed watertightly using various methods. The objective of this paper is to introduce a new innovation comprising the use of continuous cement grouting during embedding. The method has been tested on a field test site and installation and permeability features have been observed and analyzed. Installation can be carried out using traditional sheet piling machinery, merely some additional grouting equipment is needed. Installation speed of grouted sheet piles corresponds to that of conventional embedding. The permeability of the tested method is satisfactory in applications where e.g. polluted soil or water has to be isolated from the surrounding environment. In addition, this method can be used for conventional retaining walls where very low permeability is required or for reduction of soil vibration, e.g. close to a railway embankment. The new method to grout simultaneously and continuously during embedding has been developed based on respective innovations on impact driven steel piles.

Jan 1, 2006

By S. Averill, B. Schreiner, V. Sopuck

The La Ronge. Kisseynew, Glennie Lake and Flin Flon domains. the main focu for gold exploration in the southeast part of the Saskatchewan Shield, were subject to continental glacial ice advances from the northeast during the Quaternary. Based on forty-four auger hole along with surficial mapping, the general Quaternary stratigraphy in this area is observed to be composed of a lower till unit , an overlying stratified unit of glaciofluvial sand and gravel and/or a glaciolacustrine silt-clay unit. an upper till. and an upper tratified unit. The lower till is commonly found throughout the geological domains except where it has been eroded in glaciofluvial or fluvial channels. Glacial Lake Agassiz fo rmerly covered most of these prospective domains. The lacustrine deposits associated with the lake impede surficial geochemical surveys including soil. lake sediment. and biogeochemical surveys. The approximate extent of clay cover can be predicted from beach elevations. For instance. in the Waddy Lake area. clay i not known to occur above about 1,400 feet (425 m) elevation. Exploration techniques are hampered by clay in at least one third of the volcanic belt. Thi s influence is indicated by the fact that nearly all gold prospect found to date are located above 1,400 feet (425 m) while the area of clay cover is vi rtually unexplored. The upper till i related to a minor ice readvance. This till is the medium often sampled during soil surveys in the area . lts value as a geochemical ampling medium is dependent on the extent of erosional contact with bedrock highs on the lower till. Those areas which are relatively free of lacustrine and fluvial deposits are those where surface geochemical methods work best. In the Waddy Lake volcanic belt approximately 25-50% of the area may be suitable for surficial surveys. The area of the Star Lake prospect occurs above the 1,500 foot (460 m) elevation and was not covered by Lake Agas iz. The effectivene of till sampling as a surface sampling medium was tested in those areas above the clay level. Till orientat ion surveys were carried out at the Star Lake property and the Tower Lake prospect (Waddy Lake area) within the La Ronge Domain . Gold grain counts and analy es of heavy mineral concent rate from 7 kg surface ti ll samples were used to delineate dispersion trains down-ice from mineralization. In addition, the clay fraction and a 30 g (-80 mesh) subsample from the same till sample, were analyzed for gold . In the Star Lake area, ice direction is subparallel to the strike of several narrow northeast trending auriferous structures. arrow dispersion trains down-ice from known

Jan 1, 1986

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

By R. J. Fantel

The Bureau of Mines investigated the resource potential of 201 mines and deposits in 28 market economy countries and 17 mines and deposits in the U.S.S.R. and China. The 201 mines and deposits evaluated from market economy countries contain an estimated 34.2 billion metric tons of recoverable phosphate rock (at the demonstrated resource level), with Morocco and Western Sahara accounting for 61% (21 billion tons), followed by the United States with 19% (6.4 billion tons). The 17 mines and deposits evaluated in the U.S.S.R. and China contain approximately 1.5 billion tons of potentially recoverable phosphate rock. Potential annual capacity from low-cost, high-grade producing mines in the United States is estimated to decline significantly during the latter half of the next decade, and the United States will have to develop new, higher cost, lower grade mines in order to satisfy demand into the next century. Of the world's new production capacity which could likely be developed over the next decade, slightly over one-third could be produced at an estimated 1981 cost of $40 per ton or less, and about two-thirds would cost in the $40 to $50 range (including a 15% rate of return). In comparison, moot of the competing phosphate rock from producing mines in Morocco could be produced for under $40 per ton. The United States has sufficient demonstrated resources of phosphate rock (plus huge quantities at the identified and hypothetical resource levels) to satisfy domestic consumption for many years to come, but its future ability to compete in the major export markets against low-cost competitors is much more uncertain.

Jan 1, 1984

The alkaline ethylenediamine tetra-acetic acid (EDTA) leach process for extracting tungsten from scheelite (CaW04) ores has been examined for the treatment of low grade (<0.5 per cent WO,) residue dumps. The process has been considerably simplified by applying solvent extraction directly to the leach liquor.Ammonium paratungstate is thereby produced in a one step process and this obviates the need to physically recover EDTA prior to recycling. This modified process should be an economical method of tungsten extraction.

Jan 1, 1983

By G. Cockburn

Nkomati Nickel JV exploits the ores of the Uitkomst Complex near Machadodorp in the Waterval Boven district in South Africa?s Mpumalanga Province. Due to factors such as the remote location, stellar growth in production, opencast mining methods, and ore characteristics, a number of innovative processing options were selected. Nkomati has undertaken numerous initiatives over the last few years to improve plant running times, metallurgical performance, and operational profitability. Great emphasis has been placed on effectiveness of management control systems. A number of initiatives such as short interval control and time?in-state metrics have been implemented. A focus on improvement on availability and asset utilization of key items of equipment has been particularly effective. While the ores are remarkably similar to the Merensky and UG2 reefs, the relatively high base metal sulphide content and mineralogical characteristics make metallurgical treatment somewhat different to the ores of the Bushveld Complex. The low head grades and flotation kinetics distinguish Nkomati from other base metal operations. Numerous milling and flotation optimization initiatives have resulted in dramatic improvements in throughput, recoveries, and concentrate grades. This paper discusses the metallurgical, operational, and management challenges and the outcomes obtained.

Jan 1, 2014

By James Westfield

Following is a resume of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction o1 injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bitumi¬nous coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1959

By D. S. Kingery

Efficient transportation is necessary to complement modern mechanized mining methods. The increasing trend toward high-capacity face loading equipment has demanded equally efficient haulage methods; this has been met by increasing mine-car sizes, using larger locomotives, and increasing haulage speeds, all requiring properly installed and maintained haulage roads specifically designed for this type of traffic. The recommendations and specifications included in this circular were made to point out salient factors important to the proper construction and maintenance of track haulage roads and to serve as recommended standards for track installation and maintenance. GLOSSARY OF TERMS USED Haulageway. - The track, walkway, trolley wire, feeder lines signal end telephone lines, signals, telephones, support, and drainage of the entry referred to. Subgrede. - The base upon which the ballast is laid.

Jan 1, 1954

By Luis Valdivia

Dado que el objetivo principal de un departamento de Geología de exploraciones es el de estimar recursos minerales en nuevos blancos de exploración identificados a través del análisis e interpretación de información geológica proveniente de diversas fuentes. En ese sentido, el presente texto señala la sistematización de los datos geológicos como el uso de las imágenes satelitales, fotografías aéreas, geofísica, geoquímica, cartografiado geológico, sondajes diamantinos, catastro minero, datos geográficos y políticos, etc. a través de un servidor que integre dichas estructuras lógicas de conocimiento, de manera que todos puedan acceder a ella de manera fácil y dinámica. Asimismo, para los datos de carácter numérico llámense muestras, sondajes, leyes, se utiliza la plataforma Access como gestor de base de datos, mientras que para la información grafica superficial, el software ArcGis.

Sep 24, 2008

By Sunil Koppalkar, Liming Huang

"Since late 1980s the research group led by late Professor Andre Robert Laplante at McGill University undertook fundamental studies and applied research of the Knelson Concentrator (KC) and developed a sustainable method to correctly estimate gravity recoverable gold (GRG). In the early time a concept of ‘free gold’ was used, it was defined as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, its practical use had declined. Around 1994, a methodology using a 3-in Knelson Concentrator to measure gravity recoverable gold was established at McGill University. Through more than 10 years’ improvement and optimization, this technique had become a standard method to evaluate GRG for gold ores, gold plant streams and platinum group metals. Until 2006, about 200 GRG tests had been carried out at McGill University for the ores from all over the world. Recently, a modified version of GRG test (short test) with the advantages of reduced processing time and lower cost had been developed for the mundane needs of gold industry.INTRODUCTIONGold gravity recovery has evolved significantly over the past twenty-five years, mainly because of the advent of the Knelson Concentrator (Knelson 1988, 1990, 1992, Laplante 2000). Now, a series of Knelson Concentrators for different applications are manufactured and used in gold industry all over the world (Knelson Concentrators 2004).In 1980s the Knelson Concentrator gained acceptance from mining industry as an effective device for the recovery of gold from grinding circuit. Knelson Concentrator became the obvious choice because of its design features: a relatively long processing time without concentrate discharge (compared to some other centrifuges, such as Falcon Concentrator and Chinese Yunxi Centrifuge at that time), large throughput capacity, treating a wide size range of material, yielding a high grade concentrate with small mass that could easily be smelted. As more and more Knelson Concentrators were accepted in gold industry, mineral processing engineers faced with challenges: what are the separation mechanisms of the Knelson Concentrator? How much gold can be extracted for an ore if a Knelson Concentrator is installed? For answering these questions, a laboratory scale Knelson Concentrator was created."

Jan 1, 2007

By Jerry Newton

The bulk explosives industry is relatively young compared to how long explosives have been in use. It's been around for about forty years, about the length of a person's career. This period of explosives history has seen constant change. The type of product, the manufacture and the trucks that haul it have changed a great deal over the years.

Jan 1, 1997

To build an effective entry roof beam, a roof bolting or supporting system must be of the ability of providing a clamping force to the bolted roof strata. Currently, two roof bolting systems are widely used to serve the purpose of providing such a clamping force. They are resin and mechanical anchorage bolting systems. Both numerical modeling and double shear testing results indicate that a greater pre-installed load or pretension of a roof bolting system is very critical for effective beam building. Although it?s generally accepted that a mechanical anchorage bolting system can provide a greater pretension than a resin anchorage bolting system does (Su and Poland, 2007 and Peng, 2008), no published field data are available to support such a conclusion. This paper analyzes the results of our field tests on both roof bolting systems, explains why one roof bolting system is better than the other under a typical roof condition, and finally discusses the effective means for coal mine operators to determine the best roof bolting system for their roof conditions.

Jan 1, 2011

By A. W. Dougall, T. M. Mmola

"SynopsisThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs) – which are those areas of performance that are reflected explicitly or implicitly in the vision and strategies of an organization and reflect the critical success factors of the organization. This paper is a review of key performance areas in the southern African mining delivery environment. The KPAs discussed in this paper have been identified by comparing KPAs of the several mining houses engaged in surface mining operations in southern Africa and then extracting those KPAs that are common to most of them. Although the authors support the view that each organization should develop KPAs to specifically fit its needs, the study reveals that five KPAs – safety and health, costs, product quality, fleet management, and delivery should form a default list that covers the key areas that any organization should consider when choosing KPAs. KPIs are those subsets of KPAs that we measure in order to manage KPAs.IntroductionThe global resources and commodities market has become highly competitive. While southern Africa’s abundance of minerals resources is still unrivalled, it has lost considerable dominance in terms of production output. The sustainability of southern Africa’s mining industry is increasingly becoming dependent on its ability to manage the performance of its operations well. A valuable tool for monitoring and managing performance is the use of key performance areas (KPAs), which are ‘those areas of performance that are reflected explicitly or implicitly in the vision and strategies of the organization’ (Barker, 1997). The terms KPA and KPI (key performance indicator) are often used interchangeably – whether correctly or erroneously is debatable. KPIs are ‘quantifiable measurements, agreed to beforehand, that reflect the critical success factors of an organization’ (O’Neill, 2007). Each KPA probably has multiple KPIs associated with it."

Jan 1, 2015

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine ventilation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which accounts for a major portion of the market for coal, received further study. Unique power generation systems, including coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jan 1, 1965

This project, "Analysis of Men, Materials and Supplies Handling Systems in Underground Metal and Nonmetal Mines" documents the productivity and safety aspects of the existing equipment and systems utilized in transporting personnel and supplies from the surface to the underground production work place. The Present Systems Study (this text -Volume II) documents the productivity and safety of existing men and material movement systems for six representative underground metal and nonmetal mines. Identification of common problem areas was performed using recognized industrial engineering techniques. The back-up data for the industrial engineering analysis of each mine is included as respective appendices (Volume III). A summary of the study background material, six mines' problem areas, comparison of problem areas, problem analysis, and solution recommendations are included as the project final report (Volume I), bound under separate cover.

Jan 1, 1975

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice pitwall profiles are often planar in crosssection and the profile in between ramps especially tend to be planar and defined by a constant inter-ramp angle. Sometimes rock layers exhibiting different strengths require the inclination of the profile to vary with depth, but the inclination across each layer is usually constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties and Factor of Safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e. the planar profiles exhibiting the same FoS) up to 8 degrees depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Mar 2, 2022

THE following short paper on the Blair Athol coal-field will no doubt have a twofold interest to members from the fact that its main seam, known as the "Big Seam" of a maximum thickness of 91 ft without a band, is unique, being probably the thickestseam of high-grade clean coal yet known, and also because of the interesting problem it presents the colliery engineer-viz., which system of mining is the best to secure the highest economical extraction.Location - Blair Athol is a mining township in Central Queensland, situated at an altitude of about 1100 ft. above sea-level at the end of a branch railway line 74, miles from Emerald, on the Main Central Western line, and 240 miles by rail from Rockhampton.Geology - The coal-measures appear to lie in a shallow basin of about four or five square miles in area, surrounded on all sides by slates and schists, which are overlaid oh three sides by alluvial deposits of up to 150 ft. in thickness, and on the fourth by a thick basalt bed, as yet unproved, some miles beyond which the auriferous slates outcrop. These alluvial deposits have been largely worked in years past and gave high gold returns, the chief diggings being Clermont and Macdonald's Flats in the south, the Springs and Black Ridge in the north-east, and Yankee Creek and others on the west. The surface of the coal-fields may be described as unbroken, but undulating, with gentle southerly dip, the watercourses opening out into wide flats. The absence of creeks or deep gullies accounts for no outcrops being visible on the surface, and the coal-measures...

Jan 1, 1918

By L. Muñoz, L. Steffen, J. Alarcón, W. Vilas

Today, mining operations close to communities face increasing challenges, especially in their drilling and blasting operations. Proper management of environmental impacts is important to guarantee their license to operate and to provide sustainability to the mining business in the long term. Blasting is an event that generates impacts such as vibrations, noise (airblast), projections (flyrocks), ejection of dust and fumes (when there is a deficient detonation of the explosive). If any of these variables exceed the established regulations, sanctions can be generated and even lead to stop mining operations. The goal of this work is to present a review of different techniques, concepts, technologies, simulation software and monitoring / control tools to minimize the environmental impact generated by blasting. For which, a case study of a big scale open pit mine in Brazil with operations close to a community will be presented. An adequate management model, combined with good operational practices, the use of new technologies, enable a safe operation without incidents with the communities. In this way, building trust with neighbours, maintaining the license to operate, and helping mining industry to mobilize resources essential for progress in a sustainable way

Jan 1, 2024

By J. E. Hamak

This publication contains analyses and related source data for 920 natural gas samples from 26 States and 2 foreign countries. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1991