Search Documents

By B. P. Watson

The first crush pillars on the Bushveld platinum mines were introduced at Union Section in 1978. Before the introduction of crush pillars, serious problems were experienced when stoping advanced to a point 30 m to 40 m on both sides of the centre gully. At least three to four stopes were collapsing per month. The introduction of the pillars stopped the stope collapses in the mining area where they were introduced. The residual stresses of these pillars were never measured; however, the successful elimination of the ?back-break? problem suggests that the original pillars had a residual strength of at least 8 MPa. Apart from back analyses, very little work has been done to determine the residual strength of crush pillars and only very recently have any measurements been made. The lack of knowledge in this field has resulted in pillars being designed based on experience. Concerns about stope collapses, similar to the Coalbrook disaster, have led to larger pillars being cut in more recent times. If such pillars were cut in brittle quartzites they would always fail violently but the ductile nature of the Merensky Reef generally allows large pillars to fail without bursting. Occasionally, however, one would burst in a working area. Increased incidence of bursting has been reported on some mines at deeper levels but most of these bursts occur in the back areas. Nevertheless, the incidence of bursting increases the risk of falls of ground in already dangerous areas, and the larger pillars decrease the extraction ratio. This paper describes the evaluation of stress measurements conducted in two boreholes over a crush pillar with dimensions 2.5 m x4.0 m, and a height of 1.2 m. Boussinesq equations for vertical and shear stress were used to analyse the original measurements and provide a stress profile across the pillar as well as the residual strength of the pillar. The results showed an unexpectedly high peak stress of 280 MPa at the centre of the pillar and a residual strength of 48 MPa. The reason for the high residual strength is suspected to be the result of the stiff environment under which the pillar failed and the small height of the siding on the up-dip edge of the pillar. More measurements should be conducted on several mines to establish a range of residual strengths for narrow crush pillars.

Jan 1, 2008

By I M. Turnbull

QMAP (the Quarter Million Mapping Programme, 1:250 000 scale) is a geological mapping programme which will build a digital geological database of the whole country and publish maps and books to document it. The programme was established in 1993, following a recommendation by a review panel appointed by the Ministry of Research, Science & Technology, and is funded by the government, from the Public Good Science Fund. The relevance and fundamental value of QMAP lies in the greatly improved geological knowledge it will provide for researchers and other end-users of geological information.   QMAP research involves assessment of previous work, field and laboratory investigations in key areas, and data storage, manipulation and publication using Geographic Information Systems (GIS) computer technology. The QMAP digital database of New Zealand geology will be completed by 2006, as will the series of 21 full colour printed geological maps and accompanying explanatory texts. Two are already completed and published (Kaitaia and Dunedin), and six other projects are well advanced.   QMAP information will also be available in digital form. Next year we hope to expand the scope of the programme to cover the reconciling and linking of many other earth science databases to QMAP, because we believe this will create a powerful research tool. The intention is to develop internet access to the databases, to make the information publicly available.

Jan 1, 1997

By CIM Mineral Resource, Mineral Reserve Committee

Industrial minerals are generally considered to include non-metallic minerals, mineral products, or materials that provide raw material inputs for the construction, chemical, and manufacturing industries. They are often relatively low-value and bulky materials that are generally used close to where they are produced; however, some raw materials may be transported hundreds of kilometres to manufacturers and customers (ENDM, 2021). They do not include the metallic minerals, mineral fuels, or gemstones, and are used in industries based on their physical and/or chemical properties (Wikipedia, 2021). In contrast to most metallic minerals, a general distinguishing characteristic of the industrial minerals sector is their general low degree of market elasticity in relation to the market prices and product specifications. The estimation of either a Mineral Resource or a Mineral Reserve (MRMR) for an industrial minerals deposit can be affected to a significant degree by a number of factors that are not typically applicable to metallic mineral deposits. These factors can include such considerations as the particular physical and chemical characteristics of the final product, product quality issues, market size and market access. In some cases, such information may be confidential and proprietary. One of the key challenges of the industrial minerals sector is to define a commonly accepted listing of which types of minerals, materials, or mineral deposits can be considered as industrial minerals (Mining Standards Task Force, 1999). Although definitions for what constitutes an industrial mineral can vary in detail, general descriptions can be found in American Geosciences Institute (2021), Fastmarkets IM (2021), Snowden (2019), SME (2021) and Wikipedia (2021). A brief listing of some of the materials and minerals that are generally considered to be industrial minerals is provided in Table 1. For the purposes of this document, all references to industrial minerals include not only the minerals, materials, and mineral deposits themselves, but also the various commercial products that are derived from these sources.

Nov 19, 2023

By Edwin A. Clarke

[For almost 2 decades the Bureau of Mines has been Interested in converting solid fuels to liquid fuels. Small-scale laboratory investigations were carried on for a number of years.4/ This work wad expanded substantially under authority of Public Law 290, approved by the 78th Congress on May 5, 1945. As part of the. broadened program, coal-hydrogenation demonstration plant was designed and erected at Louisiana, Mo., where: hydrogen-manufacturing and compression equipment, shoes, electric power, and other utilities and facilities were available from a discontinued wartime ammonia works . The plant uses the direct -hydrogenation or Bergius process, but the process differs from prewar European practices in many respects. Many noteworthy improvements h eve bean made, particularly by substituting automatic instruments for manual control of process variable's, in line with modern American processing practices. The over-all objective of the demonstration plant is to bridge the gap between laboratory end commercial-scale operation by furnishing cost and engineering data to develop a synthetic liquid-fuels industry when it proves technically and economically justified. Fitting into the over-all program, specific objectives o early runs were to (1) train personnel who had no experience with this type of operation, (2) break in the installed equipment, (3) obtain successfully integrated operation of the entire plant, and (4) work towards obtaining data on the hydrogenation of coal-tar oil and a typical low-ash coal. In beginning fan integrated operation, it is common practice to operate and obtain reaonably smooth performance of each unit before the over-all operation is undertaken. The first part of the plant completed was the refinery, consisting of several fractionating systems, a stabilizer, and a chemical treater.]

Jan 1, 1953

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By William H. Hamilton

INTRODUCTION It was not very many years ago that tunneling machine manufacturers spent considerable time trying to convince contractors and mine operators of the advantages of mechanical tunnel boring over conventional drill and blast methods. Today there are few doubters left. There is universal agreement that, not only are tunneling machines here to stay, but the ratio of bored rock tunnels to blasted rock tunnels is increasing at an accelerated pace, and within the next twenty years I predict almost all tunnels will be bored by machine. I believe we are today at a very important mile-post in the development of tunnel boring systems. Felix Gaye stated in his recent article (1) "It is important to disseminate between the efficiency of cutting tools and the overall efficiency of the boring operation". Mechanized tunnel boring in the past placed almost total emphasis on the rock cutting and boring ability of the tunneling machine. With advancements in technology and better solutions to the problems of rock fracture, steering control, and structural design, the emphasis today can be placed on the total-system concept. Tunneling machine design, as one of the key elements in the overall system, presents many problems that are not totally solved today. These design problems are, in the most part, not related with rock fracture, but rather with criteria associated with the over-all operation.

Jan 1, 1997

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California in 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemica 1 manufacturing; a shift in requirements from metals to nonmeta ls, from inorganics to organics, from natura 1 to synthet ic materia ls , and from distant to local sources of supply.

Jan 1, 1965

By Harald Ulrik Sverdrup, Anna Hulda Olafsdottir

The long-term supply of nickel to society was assessed with theWORLD7 model for the global nickel cycle, using new estimates of nickel reserves and resources, indicating that the best estimate of the ultimately recoverable resources for nickel is in the range of 650–720 million ton. This is significantly larger than earlier estimates. The extractable amounts were stratified by extraction cost and ore grade in the model, making them extractable only after price increases and cost reductions. The model simulated extraction, supply, ore grades, and market prices. The assessment predicts future scarcity and supply problems after 2100 for nickel. The model reconstructs observed extraction, supply and market prices for the period 1850–2020, and is used to simulate development for the period 2020–2200. The quality of nickel ore has decreased significantly from 1850 to 2020 and will continue to do so in the future according to the simulated predictions from the WORLD7 model. For nickel, extraction rates are suggested to reach their maximum value in 2050, and that most primary nickel resources will have been exhausted by 2130. After 2100, the supply per capita for nickel will decline towards exhaustion if business-as-usual is continuing. This will be manifested as reduced supply and increased prices. The peak year can be delayed by a maximum of 100 years if recycling rates are improved significantly and long before scarcity is visible.

Jan 26, 2021

In presenting this address I am conscious of the honour that has been paid me in my election to this important office, and I am very aware that I follow, in the position of President, many distinguished men who have led the Institute over the 70 years since its inauguration in Broken Hill in 1893.It is perhaps appropriate tonight that I intend to talk about a metal which recalls the birth-place of the Institute, and is also one with which I have had a direct association throughout the whole of my working career. This metal is Silver.Silver is associated traditionally in everyone's mind with money and silverware, and has always been prized for its natural beauty and elegance. It is today one of the few metals in which world consumption has outstripped production, and the events which have occurred to bring about this situation make an interesting story.In telling this story, I propose firstly to indicate our development as a silver producing country, give an historical review of the metal, trace its use as currency and the factors influencing its price, and then say something of the old and new uses of silver. Finally I shall give some comments on silver production in Australia today.Australia, with 6-5 per cent of the world's output of silver, ranks sixth among the producer countries and over the years has contributed 892.5 million ounces to the world's supply which, based upon production since the discovery ofAmerica, is estimated to have been 22,150 million ounces or nearly 680,000 tons.Although our production appears relatively small by...

Jan 1, 1963

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By Lynch A. J

A method has been developed for the prediction of the performance of multi-stage grinding-cyclone classification circuits of any degree of complexity on any ore for a wide range of operating conditions. The method involves the simulation of the circuit on a digital computer by means of. mathematical models of the individual units. At present, to establish the characteristics of the ore and the machines in mathematical terms, it is necessary to know the performance of a simple system on the ore for one known feed rate and feed sizing analysis.Further work on the separate identification of the terms defining the characteristics of the ore and the machines may permit the method to be applied directly to the data derived from small scale tests on ores.INTRODUCTIONThe cost of preparing metalliferous ores for concentration processes by, grinding and classification frequently represents a major portion of the cost of treating such ores, and it is necessary both from an economic and a metallurgical point of view that grinding and classification circuits should be operated at their optimum efficiency. It will be realized that the processes carried out in all units in such circuits behave according to physical laws and, if a mathematical representation of the laws applying to each unit could be derived, optimization of the overall process for any given conditions of feed or product may not be difficult.The physical processes in both tumbling mills and hydraulic classifiers are extremely complex and do not appear at present to be amenable to a rigorous mathematical analysis. However, empirical mathematical models of grinding units which have been presented previously (Callcottand Lynch, 1963; Lynch and Moore, 1963) may be used to discuss the operation of the grinding units in multi-stage circuits. Another type of model, which leads to a reasonable...

Jan 1, 1965

By G. Merle, David L. McKay, Elmar Randveer

"THE ENGINEERING AND TECHNICAL SERVICES department is responsible for supplying the following services:1. Administration and co-ordination of the work required for capital projects.2. Engineering, design and drafting services for inplant changes or improvements as requested by the operating• and maintenance departments.3. Rock mechanics.4. Preparation of plans and layouts required for efficient extraction of the ore as mutually agreed with the mine operating departments.5. Mine planning and long-term schedules in co-operation with the mine operating departments.6. Grade control (long term and short term) and the preparation of ore and waste removal schedules to maintain a uniform grade of mill feed. This also includes the calculation of metal reserves and metal production forecasts.7. Surveying, underground and surface.8. Operations research at the mine site.9. Industrial engineering.10. Chemical analyses and assays.11. Instrumentation.12. Environmental control.A staff of approximately 35 supervisors, engineers and scientists, and 80 technicians, supply the foregoing services. Consulting engineering and drafting firms are used to supply specialized services and technical personnel in-house at Timmins to handle overloads on capital projects under the direction of Ecstall engineers.The operating and maintenance departments depend on the engineering department to supply engineering, design and drafting services for any new facilities or for any planned alteration to existing facilities. To do this efficiently requires a high level of communication and co-operation with these departments. This has been a major factor in developing the present organization of the department shown in Figure 63.The organization is predicated on a strong central technical and engineering resource from which personnel can be assigned responsibilities for different projects, and in different areas, as the work load demands. Job satisfaction is very high because of the variety and challenge in the tasks. Additionally, participation in projects with production and maintenance personnel broadens each technical employee's knowledge of operating and maintenance problems."

Jan 1, 1974

By R. C. D. Phillis

The annual mine planning process is one of the most important tactical/operational steps towards achieving strategic goals. These tactical plans are part of a very comprehensive Mineral Resource Management process, with the natural sequel to planning being execution. The execution of an underground hard rock mine plan is a multi-project environment that comprises many development-construction-equipping-stoping single project paths, which are referred to as ?stoping paths?. The uncertainty that typifies execution of projects comes in the form of untimely disruptions to constituent tasks and/or project paths. Annual mining plans also include quantified objectives for occupational health and safety, production, quality, cost, employee morale, environment, and corporate social investment. Such objectives make for a highly complex environment that management must contend with?complex in the sense that all the paths and objectives have interdependent constraints. Furthermore, at the time of this paper, Sections54*and 55**of the MHSA*** put the onus on management to ensure legislative adherence. It stands to reason that planning estimates allow excess capacity?buffers?that cushions the impact of untimely disruptions. This paper concerns the fact that despite all the buffers allowed for, time, scope, and budget creeps impact on mine planning and threaten its successful execution. As a consequence, the paper deals with buffer management, the essence of Critical Chain Project Management (CCPM). Effective buffer management provided strategic (executive level) updates without losing the tactical/operational detail necessary for job card creation, especially where professional skills and experience are in short supply. Indicative bottom-line results showed CCPM to be highly effective.

Jan 1, 2011

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

The interaction of flotation collectors with sulfide minerals takes place at the solid - solution interface. The electrochemistry of the processes which affect this interface are discussed. The interaction of xanthates with sulfides is an electrochemical process, xanthates being electro-oxidised to chemisorbed xanthate and dixanthogen. The role of oxygen is to provide a cathodic process to allow the anodic oxidation to occur. The hydrophobic condition of the mineral surface is brought about by the presence of the oxidised xanthate species. The action of reagents which can activate or depress the flotation of sulfides is discussed briefly.

Jan 1, 1971

By J. J. Jakosky

THE method of electrical mapping of oil structures to be described possesses certain limitations, as well as certain definite advantages. It, in common with other geophysical methods, is not a panacea for the solution of all subsurface geological problems. It operates on differences in electrical conductivity of the geological strata, whereas the other most-used methods operate on (1) differences in magnetic properties, (2) differences in gravimetric properties, or (3) differences in seismic properties. This modification of the resistivity method is therefore able to obtain subsurface information under conditions not favorable to the other methods mentioned. Where the other methods have been employed with ambiguous results it may act as a complementary method.

Jan 1, 1936

By Panagiota Tsolis-Katagas, Basilios Tsikouras, Tassos A. Grammatikopoulos, C. Katagas

"Mineralogical techniques including microscopic methods, reflected and transmitted light microscopy, Cathodoluminescence (CL) and Scanning Electron Microscopy equipped with an Energy Dispersive Spectrometer (SEM-EDS), are useful in determining the quality of industrial minerals. They are essential for studying ores and metallurgical products including the evaluation of physical characteristics of the mineral, paragenetic relationships, associations with possible deleterious contaminants (e.g., sulphides), spatial distribution within the ore zones and liberation characteristics. The methods are inexpensive, and provide quick identification and distinction among the industrial minerals and the gangue minerals in a section. Additionally, SEM is necessary to reveal complex textural sequences and 3-D measurements of minerals and quick semi-quantitative analysis.Common analytical methods include Electron Microprobe Analyses (EMPA) and Whole Rock Analysis (WRA) (commonly with XRF and ICP) for major and trace elements. The EMPA analyses of industrial minerals provide information on the purity of the analyzed grains as opposed to the bulk chemical analyses that may be misleading due to contamination by other associated common “gangue” minerals. These techniques have been implemented for the case studies of wollastonite, V-magnetite and muscovite. Therefore, these methods can provide extremely useful information and lead to the implementation of a successful pilot-testing programme.MINERALOGICAL EVALUATION OF DEPOSITSDespite their considerable and increasing economic importance, industrial mineral deposits have traditionally been neglected by economic geologists, and are only rarely the subject of the detailed analysis widely lavished on metallic mineralization. Moreover, in that they generally represent concentrations of “normal” rock-forming minerals, albeit commonly with particular textural and/or geochemical features, they have tended to fall between the mainstream of petrogenetic studies and mineral deposit research (Grammatikopoulos 1999). For many industrial minerals, little attention has been paid to the factors responsible for their local concentration as large and high-grade bodies. This comparative neglect has particularly been the case for minerals such as talc and wollastonite, widespread in metamorphic rocks, in which they are reasonably interpreted as components of assemblages derived, respectively, from pelitic sediments, ultramafic igneous rocks and siliceous limestones."

Jan 1, 2003

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By Lawrence Pelham

Introduction Fluorspar demand or consumption has been taken for granted in recent years, except for those that produce, market, or consume the commodity. Thinking used to be that as the steel and aluminum industry goes, so goes fluorspar. This is much less true today. The industry is becoming more dependent on chemical industries that feed primarily off hydrofluoric acid (HF) production. The US Bureau of Mines (USBM) published an assessment of world fluorspar reserves and resources. It created a foundation of valuable data that can be used to monitor fluorspar availability. Celebrations were held this year commemorating the 100th anniversary of the isolation of fluorine. The US and other countries continue to struggle with the controversy of ozone depletion and the effect of fluorocarbons on the atmosphere. Goals for the government's strategic stockpile are being reevaluated. The market for fluorine chemicals is changing and diversifying, making it a challenge to assess and forecast fluorspar/fluorine demand. US production and distribution Fluorspar Fluorspar shipments from US mines reached an all-time high near the end of World War II in 1944 at 375 kt (413,800 st). Eighty-two mines produced more than 453 t (500 st) each, and 10 mines produced more than 9 kt (10,000 st.) each. Illinois supplied 43% of total shipments. Consumption in 1944 was 372 kt (410,200 st), of which 56% was used by steel producers and 32% by HF producers. This was the last year that US production exceeded US consumption. The post-World War II record for fluorspar shipments occurred in 1951 at 315 kt (347,000 st) 58 mines produced more than 453 t (500 st) and eight mines produced more than 9 kt (10,000 st).

Jan 11, 1986

By Ihor A. Kunasz

Lithium minerals occur predominantly in pegmatites that contain mineral assemblages derived from the crystallization of post- magmatic fluids or from the metasomatic action of residual peg- matitic fluids. They have been the traditional sources of raw material for ceramic and chemical industries. With the discovery of the Searles Lake deposits, brines became new sources of lithium, and, today, two brine deposits satisfy nearly one-half of the free world demand for lithium chemicals. Indeed, lithium production from pegmatites has been superseded by brines sources. In the United States, the brines of Clayton Valley, NV, have been exploited since 1964 by Cyprus Foote Mineral Company, a subsidiary of Cyprus Minerals Company. In Chile, Sociedad Chilena de Litio Ltda., an affiliate of Cyprus Minerals Company, is now producing lithium carbonate from the brines of the Salar de Atacama. Recently identified brine deposits suggest that these may well become the prime sources of lithium chemicals. In Bolivia, the government is negotiating the rights to exploit the brines of the Salar de Uyuni. The Salar del Hombre Muerto in Argentina is being evaluated as a future center of chemical production. The brines of the Great Salt Lake of Utah, the Smackover Formation, and the Imperial Valley geothermal field have been defined as important resources of lithium. In Tibet, high concentrations of lithium have been reported in several saline lakes. In the People's Republic of China, lithium may be produced from the brines of the Dabusan playa in the Qinghai Basin. The 1950s saw a great number of lithium companies develop. However, following the termination of the Atomic Energy Commission purchase program in 1959, several companies, such as Maywood Chemical Co., American Lithium Chemicals, and Quebec Lithium Corp., were forced to close their operations. Nevertheless, with the development of new applications in glass ceramics, air conditioning systems, synthetic rubber, and metallurgy (aluminumpotlines), the lithium industry grew steadily. With the potential application of lithium metal in batteries, nuclear reactors, and fuel cells, a steady growth can be foreseen. New products and new applications are likely to stimulate exploration for expanded reserves as well as the search for new sources from which lithium could be extracted economically. Presently identified reserves and production capacity are sufficient to satisfy the conventional market growth of lithium.

Jan 1, 1994