Search Documents

By S. Bhattacharyya

"Coal bearing rocks are low in strength and have geological discontinuities and moisture sensitivity. Roof and rib falls have been a major cause of fatalities in underground coal mines. Mine engineers design ground control plans for regulatory approvals. A number of tools are available from the National Institute for Occupational Safety and Health to design and assess these plans. Quite often there is not enough geotechnical input information available and databases are used. The Appalachian coalfields have extensive scientific studies to provide reliable regional inputs. Coal mines in the western United States and Canada have different geological and geotechnical conditions, and less available data. Use of inappropriate inputs in the tools like Analysis of Retreat Mining Pillar Stability, Analysis of Longwall Pillar Stability, and Analysis of Roof Bolt Systems may result in unsafe designs or over conservative designs. The tools are convenient but thorough understanding of the inputs, calibration with local test results, and operating experience are important for effective designs. The current paper contains examples of difficulties faced during mine planning using the above tools. INTRODUCTION Sedimentary rocks hosting coal are low in strength. Scientific studies have placed the uniaxial compressive strength (UCS), triaxial strength, tensile strength, and shear strength of sandstone, shale, siltstone, and claystone in lower range of strength among engineering materials (1). Coal bearing rocks are most often weakened by the presence of faults, folds, slickensides, bedding planes, fractures, and other geological discontinuities. The host rocks and coal are often moisture sensitive. The geological discontinuities allow water to enter the strata from surface and underground sources. This combination of low strength, structural weakness, and presence of water results in difficult ground control situations for the coal mines. Roof (2) and rib falls have been a major cause of fatalities in the U.S. coal mines. Modern underground coal mines necessitate wide entries to accommodate large production equipment. The gate roads, section entries, and the mains entries of a highly productive coal mine are as wide as twenty feet (6.1 m). The actual intersection width is nearly thirty feet (9.1 m). Adequate ground control is a key to maintain safe production in such mines. Mine engineers and their consultants routinely submit ground control plans to the regulatory authorities. While working out the necessary roof control system the mine engineers are required to demonstrate the adequacy of the proposed system. There are multiple ways to demonstrate this. Some engineers use traditional load calculation approach of roof bolts (3). Some engineers use numerical methods. Yet a large number of professionals resort to a suite of ground control design software offered by National Institute for Occupational Safety and Health (NIOSH) commonly referred to as “NIOSH Ground Control Toolbar.” These software tools are free and easy to download from NIOSH website. The software included in this package are: Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Coal Mine Roof Rating (CMRR), Analysis of Roof Bolt Systems (ARBS), Analysis of Horizontal Stress Effects in Mining (AHSM), Analysis of Multiple Seam Stability (AMSS), Analysis of Retreat Mining Pillar Stability - Highwall Mining (ARMPS-HWM). These tools are relatively simple to install and use in planning and designing coal mines and prospective coal mines. They accept a number of geotechnical inputs which are collected from either an existing mining operation or from exploratory boreholes. In the absence of necessary input parameters, the programs use default values which are drawn from databases of geotechnical properties built by NIOSH."

Jan 1, 2015

"The Ernest Henry Mining (EHM) ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite. At the end of 2009, EHM converted the ball mill media charge from forged steel to high chrome media. At high pH values (above 10.5), forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response. Given this, the pH in the roughers was dropped from 10.6 to 9.6 and it was found that there was a slight increase in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold. With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.INTRODUCTION The Xstrata Copper Ernest Henry Mine (EHM) is situated 38 km north east of Cloncurry, Australia. The mine began as an open-cut operation in 1998 and transitioned to a multi-sourced operation in December of 2011, utilising ore from the newly completed underground mine in addition to ore mined from the Mount Margaret Mining operations. EHM produces a combined copper gold concentrate containing 25 000 t of copper and 35 000 oz of gold annually, utilising a three stage grinding circuit along with a four stage flotation circuit. In addition to this EHM also produces 1 000 000 t of magnetite concentrate annually via a further grinding and three stage magnetic separation circuit. Based on metallurgical test work performed by Magotteaux between 2002 and 2008, the step to change from forged steel media to 18 percent chrome media was taken in 2009 in a bid to alter the pulp chemistry to improve the flotation performance in the plant (Greet, Kinal, Twomey, & Peatey, 2010). This plant trial resulted in: • Increased dissolved oxygen levels within the pulp, • A ball mill discharge Eh shift of 25 mV to more oxidising pulp potentials, and • An EDTA extractable iron percentage reduction. These improvements in the pulp chemistry resulted in an increase of 1.7 ± 0.6 percent in copper recovery and an increase of 2.9 ± 1.7 percent in gold recovery. As the plant trial using high chrome media was successful, the use of the media was adopted as the standard for the ball mill. This implementation opened the door for further process improvements around the flotation circuit."

Jan 1, 2014

By F. H. Willcox

This publication is the third of a series of reports on hazards and the prevention of accidents at blast-furnace plants that is being published by the Bureau of Mines, Technical Paper 106a being the first and Technical Paper 136b the second of the series. This bulletin, which is arranged in three parts, treats of the causes and prevention of blast-furnace breakouts, explosions, and slips. The first part discusses blast-furnace breakouts, the hazards therefrom, causes, and features of furnace design and methods of operation that tend to prevent breakouts or lessen their number, and points out safety measures to be adopted. The second part takes up the theory and causes of gas explosions at blast-furnace plants and reviews the better methods in use for handling gas. The third part analyzes the causes of hanging and scaffolding in blast furnaces, with the resulting slips that frequently cause injury to the plant and danger to the workmen, describes features of construction and furnace design and methods of operation employed to prevent hanging and slipping, and suggests precautions and safeguards.

Jan 1, 1917

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

"A discrete element computer program named DMC-BLAST (Distinct Motion code) has been under. development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employsexplicit time integration and uses spherical or cylindrical elements that are represented as circles in2-D. DMC-BLAST calculations compare favorably with data from actual bench blasts (Preece et al,1993)."

Jan 1, 1997

The management of risks associated with slope instability is an essential process in the safe and economic operation of open cut mines. The ?slope stability radar? (SSR) has been developed to better manage those risks. The SSR remotely scans rock slopes to continuously measure any surface movement and can be used to detect and alert users of wall movements with sub-millimeter precision. The high level of movement precision and broad area coverage of the rock face can allow for a better understanding of the geomechanics of slope deformation, including magnitude of potential failures and additional warning time of impending instability. Additionally, radar waves adequately penetrate through rain, dust and smoke to give reliable measurements, 24 hours a day. SSR systems have been deployed in many metalliferous and coal mines throughout the world. Over 80 systems are currently being used with current operations in 17 countries. Greater than 200 rock slope collapses and waste dump failures (from several to millions of tones) have been monitored, with ?warning? precursor movements recorded by the SSR. This technology enables a radical change in the management of risks in open cut mining. This paper will present recent case studies of the SSR operation in coal and metalliferous mines. Slope Stability Hazards and Rock Slope Monitoring in Open Pit Mines Surface mining often creates excavation boundaries which are steeper than those would be created under natural processes in the same rock type. They are also undertake quite rapid stress changes during mining and are influenced by significant external forces such as blast vibrations and changes in groundwater. These conditions are likely to allow some degree of instability to develop in the pit slopes. The hazards associated with this instability of pit slopes can be extremely variable in character; ranging from small cobble sized rocks dislodging and falling from mine benches to complete collapse of entire pit walls. It is usually the position of mine geotechnical or geological staff to assess these hazards for mine operations. The assessment of hazards due to unstable slopes can be done by visual observation of precursor signs such as fracturing or rilling of loose material. A more reliable indicator of instability involves the quantitative measurement of outward movement and acceleration of material as an instability mechanism develops. There is strong evidence that small precursor movements of a rock wall occur for an extended period prior to rock slope collapse (Hoek and Bray, 1981). Development of a monitoring system, adopting acceptable slope deformation criteria coupled with warning systems and design of stabilization or risk reduction measures if appropriate has become a standard method of dealing with slope instability. Framework for Slope Hazard Management using the SSR A framework for the management of slope hazards is shown in Figure 1 (discussed in detail in Harries, 2007). Although this framework is specifically for use with the Slope Stability Radar, a similar framework could be developed for other monitoring technologies for monitoring slope deformation. An important point to consider is the sequential nature of the hazard management framework from selecting the context ? identifying hazards ? analysing hazards ? evaluating hazards ? treating hazards. [ ] Once the context of the system has been developed (for example ? to monitor for rapid bench scale collapse), the identification of hazards is the next stage in hazard management. Identification of slope hazards can be relatively straightforward due to the visual nature of the information that the SSR system produces. The areas of excessive wall deformation are highlighted in color maps of the mine slope with a co-aligned photographic image to review the actual site of interest. The responsible personnel must then analyses this data, usually reviewing the deformation style and rate, as well as the size of area that appears to be failing. This information can then be evaluated against organisation protocols (for example it may be only a small sub-bench failure that will be ?caught? by existing benches and hence can be categorized as a lower risk). Once these hazards are evaluated they can then be treated if required. Two major options are available to reduce the risk during this treatment option. We can reduce the likelihood of failure ? for example by buttressing the failure or de-pressurising of water pressures in a slope. However, the most likely plan of action is to reduce the consequence of the failure. One of the most successful opportunities to reduce the consequence of a slope failure is to ensure that no personnel or mining equipment is present at the location of a slope failure when collapse finally occurs. This has been the major benefit of the SSR system to the different mining operations around the world. SLOPE STABILITY RADAR TECHNOLOGY OUTLINE Slope Stability Radar system specifications and capabilities: ? Measurement precision +/- 0.1mm (std.) ? Perforated dish and other features enable it to operate in high wind conditions ? Measurement range is 1700 metres ? Scans 270 degrees horizontally and 120 degrees vertically ? 1 ? 30 minute repeat rate for area scans (varies according to area being scanned ? RF exposure (<0.05mW/cm2) is a factor of 200 below the acceptable limit for the general population (1 mW/cm2) ? Tolerant to vibration and mining equipment ? The system weighs approximately 1500 Kg ? Remote area power supply enabling unmanned, continuous 24/7 monitoring ? Real time monitoring

Jan 1, 2009

By Dominic Fragomeni

"The mineral processing industry has had a long history of innovation that is recognized but not often celebrated. These include significant advances in mineral measurement, testing, comminution, mineral separation and process control technologies that have transformed mineral assemblages into ore.This presentation presents some of the major mineral processing innovations and the impact they have had on our industry. As we look to the future, it is critical that we innovate and change. We will explore some examples of the next developments and how they can be catalyzed in the face of risk management, lower metal price cycles, resource constraints, inertia and the challenge of short term value delivery."

Jan 1, 2017

By Robert A. Cummings

A rock mass classification system has been developed for recommending drift support requirements in block caving mines. This development follows a two-year program incorporating field observations of support practice and performance in rocks of different classes, at several U. S. block caving mines. Popular rock mass classification systems presently in use for tunneling were applied at the various field sites; and were evaluated for conformance with caving mine support requirements and for general utility to caving mine operations. The developed system (MBR System) accepts readily-obtainable engineering and geologic data to yield a rational estimate of support requirements. The background and development of the MBR system is described in this report (Volume I). The use of the system is given in the Manual, a separate volume (Volume II).

Jan 1, 1984

By W. S. Dyer

The lignite deposit at Onakawana on the Abitibi river is of particular interest at the present time, since the Ontario Government has recently decided to proceed with the extension of the Temiskaming and Northern Ontario railway to James bay. Forty-five miles of steel will be laid this year to the crossing of the Moose river. This will cross the lignite field. It has been known for many years that lignite occurred in the Moose River basin, but it was not until drilling was commenced at Blacksmith rapids (or Onakawana, as the camp is now known) in June, 1929, that a seam of economic thickness and extent was found. Early in 1929 the Ontario Legislature voted $25,000 for the carrying out of a drilling programme in the Moose River basin. This came as a culmination of two summers&apos; exploratory work by the Geological Branch of the Ontario Department of Mines, and as the result of a report which said; in effect, that further information concerning the mineral resources of the basin could only be obtained by drilling, and that such a drilling programme was well worth while in order to establish once for all whether lignite, fire-clay, or oil or gas did or did not exist in economic quantities in the region.

Jan 1, 1930

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.&apos; The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

IN dealing with this subject the intention is not to write a detailed description of the various methods in vogue on the Kalgoorlie field, but rather to give a brief outline of three of the methods which are most universally in force, and from which, ultimately, a few comparisons may be drawn. The three methods which the writer proposes embodying in this article are known as &quot;The Rill,&quot; &quot;The Flatback,&quot; and &quot;The Shrinkage.&quot; For comparative purposes each method will be applied to a block of ore 500 feet in length, and opened up by levels 200 feet apart.&quot;The Rin&quot; System. It is necessary in this system, for facilitating mullocking, to make connections between levels by rising and winzing at about every 100 feet or 150 feet along the orebody. After the leading stope is beaten off for the full length ofthe drive, the level is timbered. Single stulls are put in up to a width of fourteen feet. If the span is too great for stulls, set timbers or saddleback stuUs are used. Stulls are lagged over with 4-in gimlet poles, and wooden chutes are built at intervals of 50-feet. Ore passes are cribbed up through the filling directly above each chute, and are constructed of 7-in. round timber or 9 in x 3 in square timber, the passes measuring 4 ft x 4 ft in the clear.Occasionally a double pass may be carried up, one side serving as a travelling way. Stoping is commenced off the winzes, and rills are gradually formed, one on either end of each winze. The rills are generally at an angle of 37&#176; off the horizontal, this allowing for the boring...

Jan 1, 1909

By F. E. Goodwin

Since the last CIM Zinc and Lead Conference ten years ago, significant technical and market forces have influenced how these metals are used, and the geographic distribution of their uses. Unprecedented price fluctuations have opened competitiveness issues, while the rapid growth of the Chinese market has created challenges both inside and outside China. Recent technical developments in battery energy storage, coatings, castings and chemical applications of lead and zinc will be reviewed together with the influence of these trends on end use markets.

Jan 1, 2008

THE object of the present paper is to give a brief description of the metallurgical process followed by the Grand Junction Co, and the results obtained therefrom. All figures quoted are from the actual working of the plant over a period of six months from January to June, 1910. The short ton of 2000 lb. is used by the company. Its gold is valued at 84s. per oz. fine, silver at 2s. per oz. fine. The ore consists essentially of a gangue of quartz and calcite, with 8 to 10%sulphide-pyrite, sphalerite, galena, chalcopyrite, and traces of arsenic and antimony. The colmtry-rock is a highlyaltered dacite. Small stringers of highly-mineralized ore penetrate the footwall of some of the lodes, forming a valuable stockwerk up to 3 ft. in thickness. In stoping, this is mined with the well defined lode, thus bringing into the mill at times a considerable quantity of hard country-rock. The gold exists in an exceedingly fine state of division, consequently rendering it necessary to grind very fine to obtain a satisfactory extraction.

Jan 1, 1912

By Sri Sawmliana, P. Pal Roy

Blasting Gallery (BG) method was introduced in India for higher production and low cost of excavation to substitute conventional hand section and stowing methods for thick coal seam. The Singareni Collieries Company Ltd. (SCCL) adopted this method in the year 1989 and since then successfully operating at GDK-10, GDK-8 & VK-7 Incline mines in Andra Pradesh, a southern state of India. It is also successful at Chora 10 Pit Colliery of Eastern Coalfields Ltd. (ECL) in West Bengal whereas at East Katras Colliery of Bharat Coking Coal Ltd. (BCCL) in Jharkhand State, the method has been partially successful due to some geological constraints of the area.

Jan 1, 2003

"INTRODUCTION Industrial utilization of the present submarginal domestic manganese resources of the United States is wholely dependent at this time on the electrolytic manganese process established as the result of 4 years of continuous operation of the Bureau of Mines pilot plant at Boulder City and 7 years' operations of the Electro Manganese Corporation commercial plant at Knoxville, Tenn.Three Kids ore provided the feed for the Boulder City pilot plant during 3 years of operation. Hence, the electrowinning characteristics of the ore have been thoroughly established, making possible accurate estimates for commercial operations.Before the Defense Plant Corporation constructed the leaching plant, the Bureau of Mines conducted an exploration project to determine the extent and grade of the ore reserves. Additional exploration, development, and mining by the Manganese Ore Cc, have accurately determined the tonnage and grade of ore. A large tonnage of stock piled ore is now available for immediate processing, and a considerable tonnage of openpit ore has been stripped of overburden preparatory to mining. Numerous facilities, such as power, water, and housing, needed for an electrolytic manganese plant are already available.All of these factors, as well as plans for installation of scale electrolytic manganese plant facilities, are presented in detail in the chapter entitled, ""Mining and. Electrolytic Reduction of use from Three Kids Manganese Mine."" The Manganese Ore Co. kindly provided information on the present ore reserves and state of development of the mine."

Jun 1, 1945

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

Several primary ingot producers have introduced price changes for July. Howmet Aluminum Corp., Revere Copper and Brass, Inc. and the Anaconda Co, will increase late-July prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound, Prior to this, Kaiser Aluminum and Chemical Corp. had advanced June ingot values by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants held June quotes at a range nearing 50-50.8 cents per pound. ANTIMONY Although NL Industries, since April of this year, stopped publishing prices for RMM and Lone Star antimony grade, values of domestically-refined antimony in alloy are being made available to industry, The current price of this material is $1.75 per pound of antimony contained in alloy, New York dealer-marketed metal was available in June at $1 -13-$1 .20 per pound. Important industrial uses of antimony are for flame retardants, storage batteries, chemicals, pigments, rubber, plastics, glass, ceramics and machinery.

Jan 1, 1978

By A. Eccles

Phase designs are the foundation upon which all open pit mine sequence optimizations and budgets should be built. Unfortunately, at times, mine engineers skip the step of developing realistic pit phase designs - designs that include access ramps and mineable widths. Without mineable phase designs, their optimized schedules are based on theoretical pit shells or ?quick-and-dirty? plans with no ramps. The output from such optimizations is almost always overly optimistic. Without mineable designs, the production estimates are misleading, because they overestimate ore, and underestimate waste stripping requirements. Worse yet, when plans are not based on realistic phase designs, they can point to exactly the wrong decision in feasibility studies (i.e. ?go? when it should be ?no-go?). This paper discusses the importance and features of good pit phase design, and demonstrates the pitfalls of relying on optimized production sequences that are not based on properly designed pit phases.

Feb 27, 2013

By Edwards A. B

The following note on the mineral association in the ores of the Tennant Creek Goldfield, Northern Territory, is largely based on Mineragraphic Reports Nos. 49, 89, 117 and 193 of the Council for Scientific and Industrial Research. These reports are the results of the examinations of auriferous specimens from a number of mines of the goldfield and are now supplemented by the examination of further specimens from Mt. Samuel forwarded by Mr. V. G. Martin.The Tennant Creek Goldfield lies in the central portion of the Northern Territory, about Lat. 190 35&apos;, Long. 1340 15&apos;, on the Overland Telegraph Line and about 369 miles north of Alice Springs. It comprise an area extending about 50 miles east and west, by 30 miles north and south.The geology of the goldfield has been described by Woolnough. (2)The rocks of the area are of pre-Cambrian age, and consist of talcose, chloritic, micaceous and siliceous schists of sedimentary origin, interbedded with flows or dykes of schistose quartz porphyry, and of granites which were intruded subsequent to the regional metarporphism of the area. The rocks are moderately folded, but the beclding tends to be obscured by a pronounced east-west cleavage. The most continuous orebodies run east and west, parallel with this cleavage.Numerous lenses of hematite occur in the schists, with their long axes, parallel to the cleavage, and the gold values of the field are frequently associated with such hematite bodies. The dimensions of these hematite bodies are variable but rarely exceed a length of 300 ft., with an average thickness between 10 and 30 ft.; the original vertical dimensions are thought to be comparable with their length. The lenses tend to occur in groups when they are arranged en echelon both horizontally and in depth; and erosion has exposed individual lenses to different degrees, ranging from incipient exposure to complete removal. The existence of unexposed hematite lenses at depth has been proved by geophysical surveys, coupled with drilling tests. (3)A few of the bodies are pipe-like. Many are surrounded by a casing of brecciated rock, composed of fragments of hematite and shattered country rock, and presumably caused by subsequent earth movements which crushed the country rock against the resistant hematite bodies. In the early days of the field most of the important gold occurences were found within these crushed zones, or, to a less extent, within the hematite bodies themselves.These occurrences appeared to be associated only with those hematite lenses which were intersected by quartz veins or other lines of weakness, of later origin than the crushing. This led Woolnough to think that the introduction of the gold and attendant bismuth was subsequent to the...

Jan 1, 1942

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and des¬cribes some systems of transportation `utilizing rail haulage, ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940