Search Documents

By Richard Rittenhouse

This program was to develop a new base line system for automated continuous room and pillar type mining. The primary requirement estab¬lished for this machine is that the machine be capable of mining and bolting simultaneously. Additionally, this machine was to provide temporary and permanent roof control, have a productive - full - face semi-automatic mining system, leave a clean entry outby the machine, provide maximum operator protection, provide effective dust suppression and provide air scrubbing to restrict respirable dust to permissible levels. The machine has effectively demonstrated the ability to mine and bolt simultaneously. Additional above ground operation, testing, and time studies are recommended to further verify the machines abilities. Design improvements are recommended for future generation AES machines. These relate to marginal design areas such as side loading on vent duct lift cylinders, etc., that will not impair additional testing of the existing machine.

Jan 1, 1983

By T. H. Jeffers

The Bureau of Mines conducted a laboratory investigation of copper electrowinning from electrolytes produced by solvent extraction. The purpose of the research was to gain a better understanding of the fundamental relationship between copper electrowinning conditions, anode corrosion, and cathode purity. Processing variables were evaluated in a cyclic semicontinuous system in which the depleted electrolyte was used to strip copper from loaded organic extractant. For the production of high quality copper cathodes, the electrolyte was dosed with cobalt and stripped of organic solvent extraction reagent. An optimum cobalt addition of 60 ppm, and removal of the entrained extractant with activated carbon provided the best conditions for electrowinning copper containing the least amount of lead and controlling anode corrosion. As little as 13 ppm of the entrained organic extractant, LIX 64-N, significantly accelerated anode corro-sion. However, the addition of 1,000 ppm of organic diluent kerosine did not affect anode corrosion. After cobalt dosing and removing the entrained extractant, cathodes containing less than 2 ppm lead were consistently electrowon at widely varied current densities, electrolyte copper and acid concentrations, and temperatures. Dosing of the electrolyte with selected impurities including magnesium, aluminum, manganese, and iron did not affect the cathode purity. However, 0.05 giL of chloride ions markedly increased anode corrosion and the sub-sequent transfer of lead to the cathode copper.

Jan 1, 1985

By Russell Barr, Robert E. Cook

As most mining companies are taking advantage of the high market prices for base metals such as steel, copper and zinc, numerous challenges still face them. While demand is strong from countries like China and the United States, demand is still mixed in Europe. This leads to the question of how long these high prices and overall high global demand will last. The tremendous market prices of most precious and base metals have enabled many companies to pay down a significant amount of debt accrued during acquisition and capital expenditure phases. Additionally, mining companies have been able to internally fund and engage in large projects to address future growth, (Less, 2006), thus maximizing the performance of the existing asset base, driving maintenance costs down, and improving and empowering the work-force (Mining Journal, 2006). Market prices and general efficiency gains have addressed these issues to some extent. However, critical issues still face operating managers in the mineral pro-cessing side of the industry. Energy prices, for example, continue to have a negative impact on cash costs for producing an ounce of gold or ton of a given base metal (Cummins, 2003).

Jan 1, 2007

By Ian Hooper, Alan Winter, Stefan Sadokierski, Craig Covil

The existing Tappan Zee Bridge was built in the late 1950s and has been working over its design traffic load for some time now. A new project, which is being jointly sponsored by the New York State Thruway Authority and Metro-North Rail Road, is looking at new alternatives to provide new road and rail crossings of the Hudson River. These include 2 to 5 mile and potentially longer tunnel crossing options that include hardrock TBM and EPBM opportunities. The paper describes the project needs and tunnel concept design work done on some of the alternatives. It also relates to the current EIS process for the project and talks about a possible double-stacked tunnel option. It also talks about the geology and environmental constraints relating to tunneling and provides and introduction to the tunnel ventilation work necessary for tunnel crossing of this magnitude. It does not report on the bridge engineering options being evaluated.

Jan 1, 2005

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By Lucia Kuizon

The Pinnacles Wilderness Contiguous Wilderness Study Area (WSA) (CA-040-303) is 30 miles south of Hollister, CA, in San Benito and Monterey Counties. It is composed of five parcels of public land totaling 5,838 acres adjacent to the Pinnacles National Monument. The U.S. Bureau of Land Management later reduced the size of the Recommended Suitable Area (RSA) to 2,200 acres. U.S: Bureau of Mines personnel examined the entire WSA in May 1984. The WSA is underlain by Tertiary sedimentary and Cretaceous plutonic rocks. Diatoms occur in interbedded tuff, shale, and sandstones in the northern part of the WSA, but outside the RSA. In 1984, there were no mines, prospects, mining claims, leases, or mineral resources in or within one mile of the study area. No energy minerals were identified; however, an oil well was drilled in 1951 in the northern part of the WSA, but outside the RSA; it was a dry hole.

Jan 1, 1985

By P. B. Baxendell

The appraial of producing properties and profitability ntzalysis of a proposed capital expenditure are based on the same principles. In both problems a projection of future cash income is. cornpared to one or more capital expenditures. Several different methods have been in use either to compute a price to obtain a given earning power on the investment or to compute the earning power which will result from a given capital expenditure. One of these, the "Average Annual Rate of Return" method, computes in a simple manner the ratio of the present value of the future earnings after amortization to the present value of the undepreciated balances of the investment over the life of a project. This method, not well known generally, appears to have some rather unique advantages in reducing the computation work required, eliminating trial-and-error solutions, and providing a more accurate answer when applied to oil industry investments subject to the unit-of-production basis of amortization. Its derivation is given and its versatility demonstrated in the solution of certain everyday investment problems. A number of charts, useful in applying this method to profitability analysis and appraisal work, are provided. The current trend in the market values of producing properties is shown. INTRODUCTION Making sound capital expenditure decisions requires an objective means of measuring the productivity of individual investment proposals. Since the best measure of the economic worth of such proposals is their ability to produce profits, it is common practice to grade proposed capital expenditures according to their annual earning power as a percentage of the outstanding capital. The same principles which govern the determination of the rate of return of proposed capital expenditures also apply generally to the problem of determining the appraisal value or purchase price of income-producing oil and gas properties. Both problems are of prime importance in the producing phase of the oil business, where management is faced daily with decisions to drill or not to drill certain development wells, or with the determination of the appraisal value of producing properties. The common feature in both problems is that a projection of future cash income is compared with a known or estimated capital investment to determine itsiearning power or annual rate of return. In the case of development drilling, the cost of the proposed well can usually be estimated with a fair degree of accuracy and the problem consists of finding the rate of return on the invested capital. In the case of appraising producing properties, on the other hand, the desired rate of return is usually known in advance and the problem consists of determining the purchase price which, for the given income projection, results in the fequired rate of return. Certain accounting procedures common to the oil and gas producing business make these two problems and their solutions somewhat different from corresponding problems in other industries, and, in certain ways, simpler. The main difference is in the amortization policy which, for oil and gas production, is frequently on a unit-of-production basis, compared to the amortization on a time basis used in many other industries. The purpose of this paper is to discuss briefly the various methods currently in use for the measurement of productivity of invested capital in producing properties and, in more detail, the derivation and application of what will be called the "Average Annual Rate of Return Method". This rather interesting and not too well known method has some very definite advantages in the solution of many problems common to the oil industry. For the sake of simplicity, federal income tax considerations have been disregarded in the examples used, since they do not affect the principles involved. The use of the production payment route in the sale or purchase of producing properties, which has been amply covered in many other publications, has also not been included in this analysis. METHODS FOK MEASUKING THE EARNING POWER OF INVESTED CAPITAL, Of the many different methods used to measure the earning power of invested capital, four are applicable to oil or gas production ventures. Depending on whether these four methods utilize one or two interest rates, and whether a fixed amortization pattern is used, they may be classified as follows.

By G. Kang

The ferroalloys industry has generated historically substantial solid waste. The accumulated waste causes serious problems to the environment. However, it is possible to transform the solid waste into an environment-friendly resource to serve the human being. Consequently, the construction of plants that are ?environment-friendly? and that accommodate ?recycling? has become a target of most ferroalloy producers in the world to ensure sustainable development. This paper introduces the practice of Shanxi Jiaocheng Yiwang Ferroalloys Works, the biggest manganese metal producer in China, in the development of an ?environment-friendly and recycling? process. The process includes power generation using coal gangue, waste from local coal mines; hollow bricks manufacture using slag and fly ash from the power station; cement production using slag from ferroalloy smelting; recovery of ferrous and non-ferrous elements in the dust from the furnace gas cleaning system; application of silica dust in construction and so on. The final objective of the plant is to realize zero discharge of solid waste. The profit of the ?environment-friendly and recycling? process compensates in part for the operational expense of the environment facilities.

Jan 1, 2004

By H. J. Modi, D. W. Fuerstenau

pH effectively regulates the flotation of corundum through its control of the surface charge. Since collector ions function as counter ions in the double layer, the collector must be anionic when corundum is positively charged and cationic when it is negatively charged. Even a long-chained xanthate will float positively charged corundum. Association of the hydrocarbon chains of the adsorbed collector ions gives rise to increased adsorption and increased rate of flotation. Because of this phenomenon, neutral organic molecules aid flotation although the unionized collector cannot promote flotation independently. Na2SO4 was found to depress the flotation of corundum with animic collectors through ionic competition whereas the same salt activates corundum for flotation with cationic collectors. A close connection between ion association, electrokinetic behavior, and floatability is suggested. As part of the increasing interest in the physical chemistry of flotation, strong experimental evidence has been obtained which indicates that organic ions are adsorbed as counter ions by non-metallic oxide minerals mainly because of the electrical forces which exist at interfaces(1-3). Thus flotation of such minerals without activation should then be appreciable only when the mineral and the collector are oppositely charged. Since only limited work has been reported on the effect of surface charge upon flotation behavior(3) this general hypothesis on the flotation of insoluble oxide minerals has not been tested thoroughly. Investigating the flotation of a mineral for which extensive electrokinetic data exist yields a way to test this hypothesis more extensively. The electrokinetic behavior of corundum in solutions containing both organic and inorganic electrolytes has been studied quite thoroughly' Electro-kinetic measurements have shown that in the case of corundum, simply by controlling pH the solid surface can be charged either positively or negatively. For this reason corundum was chosen for study. The object of this paper is to present a study of the flotation of corundum and to explain the results in the light of our knowledge of adsorption mechanisms gained from streaming potential investigations. This paper is concerned mainly with the effect of surface charge on flotation with anionic and cationic collectors, but in addition such flotation phenomena as collector hydrolysis, Van der Waals attraction between hydrocarbon chains, ionic competition, and activation are discussed. While the present paper is confined to a reporting of the data obtained and some of the more immediate conclusions, it will be seen that the results, in combination with those on other systems, do promise a

Jan 1, 1961

By William R. Yernberg

Most citizens take it for granted, but minerals produced in the mines of the western United States, including Colorado, are crucial to nation’s standard of living and quality of life, said Colorado’s Gov. Bill Owens in his welcoming remarks at the 106th National Western Mining Conference. The conference, which was organized by the Colorado Mining Association (CMA), was held Feb. 4-6, 2004, in Denver. Attendance was425, up substantially from last year’s meeting. The meeting included the CMA annual membership meeting as well as the CMA chairman’s and president’s reports. The meeting also included awards presentations in which companies were recognized for their efforts in pollution prevention, health and safety, and reclamation. The conference also included a tradeshow.

Jan 1, 2004

Application of Gy?s formula is appropriate for calculation of the Fundamental Error (FE) prior to samples being collected at any stage of the minerals process, provided that sampling parameters K and a (alpha) have been determined by calibration of the ores. Two types of calibration procedure are well established in the industry, the Hetrogeneity test and the 32-piece sampling tree experiment. The sampling tree experiment uses the variance and average grade of metal analyses from four series of samples at different nominal fragment size, as the basic input data. Pierre Gy suggested the cube as an appropriate exponent of the nominal fragment size for use in his equation. More recent work suggests that this exponent is variable and characteristic of specific ores and therefore requires calibration. The method described here explains the experimental procedure of the calibration. It is then possible to calculate a sampling nomogram using the sampling parameters K and a. This allows the sampler to determine a suitable protocol for the sampling event that will ensure that the FE does not exceed a predetermined precision at any point in the sampling procedure.

Jan 1, 2007

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013

By J. Kraemer, A. Preusse

In the federal state of North Rhine Westphalia (Germany) small and medium sized companies are beginning to extract the related gas via old shafts or boreholes and to use it as a source for the production of electricity and heat. More than 100 applications for the separate mining right on mine gas had already been filed by beginning of 2002, since mine gas is treated as a mineral resource under the Federal Mining Law. Meanwhile more than 40 mine gas concessions have been granted and first projects are being developed with encouraging results so far. To enhance the applied techniques and their efficiency Aachen University has formed a research team in this discipline. Scope and goals of this research activities are being presented in this paper. Keywords: extraction mine gas, Renewable Energy Act, Ruhr District.

Jan 1, 2003

By Erik Sundström, Magnus Nygren

The study explores the influence and consequences of safety initiatives on the development of safety cultures in the Swedish mining industry. It involves interviews with experts from four mining organizations, highlighting themes such as organizational structures, safety leadership, feedback, and communication.

Nov 1, 2023

By C. E. T. White

Although trace amounts of Indium are found in many ores, commercial production of the metal has come almost exclusively from residues, flue dusts and slags generated by Zinc recovery operations. Our paper attempts to summarize the various approaches used to recover Indium from these by-products. Some comments on production and price trends are included as well as our views on future availability.

Jan 1, 1982

By J. D. Noll, S. E. Mischler

Measurement and sampling of diesel particulate matter in mine air presents a challenge due to the complexity of the diesel aerosol. The results of a series of tests carried out by the National Institute for Occupation Safety and Health, Pittsburgh Research Laboratory, in an underground mine were used to evaluate several measurement methods that are currently used to characterize particulate matter emitted by diesel-powered equipment. This paper presents an overview of these techniques and examples of the results along with a discussion of the advantages and information gained by each technique. The measurement methods discussed include particle size measurements using a scanning mobility particle sizer, total particulate matter measurements using a tapered elemental oscillating microbalance, a size selective sampling method for workplace and personal exposure assessment and a size-selective high volume sampling method for carbon analysis.

By Noel Dent

Increasing interest is being expressed in the development and availability of Electronic Delay Detonators throughout the world. Particularly in open-cast mining, the benefits associated with precise, reliable initiation systems are perceived to be considerable. Many of the systems currently being developed have sophisticated programming requirements associated with them, or are numbered systems that require predetermined layouts to determine timing patterns, and importantly are far more expensive than existing initiation systems.

Jan 1, 1994

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

VOLUME I Volume I of this three-volume report is the result of development of a comprehensive, coordinated approach to site data-acquisition activities to produce key plans and reports during the evaluation and development of a surface coal mine. A logic diagram illustrates activities in the planning and decision-making process from exploration through post-mining monitoring. The report briefly discusses major elements, other than the site environment, which influence development of mining and reclamation plans and refers to other readily available literature for details outside the scope of this study. The essence of the rationale is shown to be the 1 employment of necessary skills at the proper time to evaluate specific data ' requirements and integrate them into a cost-effective program to produce initial and major feasibility reports, mining, and reclamation plans, and the environmental impact assessment.

Jan 1, 1976

By M A. Tuck

The dominant heat loads in a deep underground mine are the surrounding rock mass, autocompression and machinery. In addition heat can be contributed to by other sources. Many block cave, sublevel cave operations and coalmines utilise conveyors to transport broken rock out of mine, in some cases completely, in others in combination with other forms of transport. This broken rock can be loaded onto the conveyor at virgin rock temperature and can represent a major heat input to the ventilation airflow as it is transported out of the mine. The purpose of this paper is to review established knowledge regarding heat flow, from conveyed rock to determine the main factors influencing the heat flow and to develop a methodology for predicting heat flow from caved rock. The paper concludes with suggestions for further research in the area of conveyed rock heat transfer.CITATION:Tuck, T A, 2017. Accurately estimating heat load from conveyed rock, in Proceedings Australian Mine Vent Conference 2017, pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017