Search Documents

By R. D. Currie

A study of the accident statistics in the coal mining industry convinces one that an organized effort must be put forth to prevent the vast destruction of human life in this industry . The fatality rate in Pennsylvania has not improved in the past several years and during 1928 it was higher than the average for the period 1916 to 1927 , inclusive . Although the accident rate for this State is less than that of the coal mines of the United States as a whole , nevertheless the rate is unduly high ; however , there are many companies which have exceptionally good records as regards both fatal and nonfatal accidents . A study of the methods used by some of these relatively good- record companies to reduce accidents in their mines shows that they exert an organized effort to prevent accidents , and that their safety organizations usually affect every employee in and about the mine from the highest official to the check boy . The chief executive must be actively and personally interested in accident prevention if real safety results are to be obtained ; when he shows this interest it is almost invariably reflected in the officials under him and throughout the organization . Safety organizations vary in form and are readily changed or adapted to the varying conditions found in the bituminous field . The companies whose organizations were studied in preparing this report are all getting good results , and it is their opinion that the safety organizations have been a big factor in obtaining these results . At their request the identity of some of the companies whose organizations were studied has not been divulged in this paper , but this does not affect the value of the information concerning their safety organizations .

Mar 1, 1931

Previous methods for measuring the flow of solids in Jnrdraulic conveying have not considered the important effects of slip velocity and particle concentration. In this paper an extension of the method proposed byShirato et al. (J. Chem. Engng. 'Japan, 1: 164-167) for determining mass flow in a vertical conduit is outlined.The present method consists of measuring' the volumetric flow of the slurry (by a magnetic flow meter for instance) and the density of the slurry in two pipe sections of different diameters. Effects of variation of slip withparticle concentration, not previously considered, are allowed.Problems involved in estimating the density of a slurry from differential pressure measurement are discussed.The major problem is the uncertainties in estimating frictional losses due to the wall in two-phase flows. The greater reliability of a more "direct" technique, such as by 'Y-ray absorption, for measuring solid concentration is emphasized.

Jan 1, 1971

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By M. Ramulu, A. Raina, A. Chakraborty, Jethwa Choudhury, Dudhankar

Application of digital image analysis technique for assessment of blast fragmentation is gaining grounds in India, very recently. Central Mining Research Institute, India made its maiden attempt to optimize blast design based on fragmentation assessment of one of the biggest opencast mines of Singareni Collieries Company Limited, India. Indigenously developed photoanalysis software called ‘FRAGALYST’ was used for measurement of blast fragmentation A series of trial blasts were carried out in overburden benches with ongoing blast parameters and pictures of muck pile were taken by video camera for image analysis. Cycle time study of loaders and dumpers was done to determine machinery performance for each and every blast. Optimization of pre-blast parameters like specific charge, specific drilling and post-blast results like shovel cycle time and dumper cycle time, was done to determine optimum range of fragmentation. Interpreting the mean fragment size (K50) obtained by image analysis the blast design parameters were modified.

Jan 1, 2001

By S. T. Johansen, B. T. Løvfall, T. Rodriguez Duran

In this paper we develop a physics-based model for lining erosion in steel ladles. The model predicts the temperature evolution in the liquid slag, steel, refractory bricks, and outer steel shell of the ladle. The flow of slag and steel is due to forced convection induced by inert gas injection, vacuum treatment (extreme bubble expansion), natural convection, and waves caused by the gas stirring. The lining erosion takes place by dissolution of refractory elements into the steel or slag. The mass and heat transfer coefficients inside the ladle during gas stirring are modelled based on wall functions which take the distribution of wall shear velocities as a critical input. The wall shear velocities are obtained from computational fluid dynamics (CFD) simulations for a sample of scenarios, spanning out the operational space, and a model is developed using curve fitting. The model is capable of reproducing both thermal and erosion evolution well. Deviations between model predictions and industrial data are discussed. The model is fast and has been tested successfully in a ‘semi-online’ application. The model source code is available to the public at [https://github.com/SINTEF/refractorywear].

Apr 16, 2024

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

The paper presents the development of an integrated computer aided design and planning of open cast mining, with the use of object-oriented modelling and geoinformation technologies, on the example of interaction of the subsystems on planning optimisation and freight traffics.

Dec 6, 2010

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920's through 1950's, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

Greater use should be made of lineations in investigations of the engineering properties of rock masses and in structural studies guiding prospecting programmes.A prominent alignment of elongate mineral grains and stretched pebbles usually marks the primary direction in which metamorphic rocks have been extended by flow. In local adjustment zones separating masses that have extended different amounts, this lineation has been a direction of slip. Kinks and crumples resulting from this slip lie in secondary lineation directions transverse to the primary mineral lineation.During deformation relatively mobile materials move into dilatant zones caused by irregularities in primary flow directions. This secondary movement transverse to lineated, primary-flow directions is the cause of crenulations and folds with axes parallel to flow lineations.INTRODUCTIONThe arrangement of inequidimensional particles in rocks is rarely statistically random. Platy minerals tend to be parallel to bedding and foliation planes. Elongate particles and linear structures lie most frequently in certain lineation directions. The types of elongate particles in lineated rocks include needle and blade shaped mineral grains, sheared out segregations, and stretched pebbles, amygdules, and aolites.Crenulations and kinks are the most common of the linear structures involved.Faint lineations are readily overlooked. Even strong lineations have been ignored. This is unfortunate as even weak lineations may be important.Use of lineation information Well-developed lineations influence the mechanical properties of rocks. Quarry workers have long known that the mechanical properties of rock masses vary directionally...

Jan 1, 1965

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959

Research by the National Institute for Occupational Safety and Health (NIOSH) on multiple-seam mining has resulted in two new ground control products. Information Circular (IC) 9495 In some U.S. coalfields, particularly in central Appalachia and the West, most mines are operating above and/or beneath previously mined seams. The effects of multiple-seam interactions can include roof falls, rib spalling, and floor heave. These can seriously threaten the safety of miners and disrupt mining operations. Information Circular (IC) 9495 is a proceedings document containing a variety of papers that summarize recent knowledge about multiple-seam mining. A NIOSH study that analyzed case histories collected from 44 U.S. coal mines is described in detail. The study confirmed that overmining is much more difficult than undermining, and isolated remnant pillars cause more problems than gob-solid boundaries. The study's results were the basis for the Analysis of Multiple-Seam Stability (AMSS) software package. The proceedings also contain two papers describing the LaModel family of software. The original three-dimensional version of LaModel is essential for detailed analyses of complex multiple-seam scenarios. LaM2D implements a simplified, two-dimensional model suitable for quick approximations of the multiple-seam stresses and strains. Three papers in the proceedings focus on case histories. One describes the extensive multiple-seam experience at the Harris No. 1 Mine in West Virginia, a second contains examples of "extreme" multiple-seam mining from the central Appalachian coalfields, and a third describes interactions with regard to longwall mine experiences in Pennsylvania, West Virginia, and Utah. The final paper reports on a numerical modeling study that provided some insight into the mechanics of multiple-seam mining. [ ] AMSS Software Package NIOSH has developed a simple, user-friendly computer program called Analysis of Multiple-Seam Stability (AMSS). AMSS can help mine planners to evaluate each potential multiple-seam interaction and take steps to reduce the risk of ground control failure. AMSS begins by evaluating the pillar design. It first calculates the single-seam pillar stability factor (SF)

Jan 11, 2007

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By David Chapman, Glen Frank

Due to the transport mechanics of the depositional environment, glacial soils display a very wide range of grain sizes and behavior. Several nonstandard drilling, sampling, and analytical techniques are therefore required to characterize the subsurface. The paper summarizes the geotechnical investigation for the design of a large project in glacial geology, which will include both large and small diameter pressure balance tunneling. The paper focuses on the challenges presented by the glacial environment and the techniques required to identify and characterize it for design and contract document preparation.

Jan 1, 2001

By B Chi, A Mahanta, R A. M Maddever, O Dominguez

BHP Billiton, in collaboration with Sodern and CSIRO, has developed a downhole logging tool for measuring geochemistry in situ. The FastGradeTM 100 (alternatively, FG100), exploits pulsed fast and thermal neutron analysis (PFTNA) to analyse the rock. This method is based on the detection and measurement of characteristic gamma rays emitted from isotopes in the material that become briefly radioactive when they are bombarded with neutrons. The tool outputs raw spectra arising from three types of neutron interaction, namely, inelastic scattering, neutron capture and neutron activation, which occur in successive time-windows (Smith et al, 2015). The spectra contain peaks at specific energies that are characteristic of the different elements interacting with the neutrons, the gamma count of which is related to elemental concentration. BHP Billiton uses in-house data processing software to convert the measured spectra to elemental concentrations.Much work has been done to understand the tool response under a wide variety of environmental and operating conditions, including logging speed, borehole rugosity, the presence of cavities, water etc. Effort has also been directed at understanding and quantifying the current sources of error in our conventional assays due to sample collection, preparation, and laboratory instrumentation in order to use this information as a baseline to compare against the FastGradeTM 100 results.To date, the FastGradeTM 100 primary use has been as a verification tool (JORC, 2012). However, beyond this, it has considerable potential to improve productivity in both exploration and production environments due to its ability to provide geologists with assay results soon after a hole is drilled.This paper presents initial test work and tool performance, including accuracy and precision under various conditions. Results are illustrated by comparing tool measurements to assays from laboratory samples collected from both reverse circulation and diamond-drilled holes.CITATION:Chi, B, Maddever, R A M, Mahanta, A and Dominguez, O, 2017. Near real-time assay with downhole assay tool (FastGrade™ 100), in Proceedings Eighth World Conference on Sampling and Blending , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017