Search Documents

By S. H. Ash

THIS REPORT covers the second in a series of five projects into which the Conowingo tunnel system has been divided for geographical and practical reasons. It outlines the construction work contemplated-to sink two shafts on the line of the main tunnel that are designated the Nos. 9A and 11 shafts, to turn off from the No. 9A shaft the Lansford and Lykens laterals, and to drive portions of the main tunnel. An emergency pumping plant, consisting of 2 separate pumprooms, each containing 3 horizontal-type centrifugal pumps of 100,000-gallons-per-minute (g. p. m.) capacity, will be constructed at the No. 9A shaft. From the No. 11 shaft will be turned off the Trevorton lateral and portions of the main tunnel, which will connect with the section driven from the No. 9A shaft. Under the proposed project, the Lansford lateral will be driven for a distance of 2 miles, the Lykens lateral for a distance of 10.56 miles, and the Trevorton lateral for a distance of 20 miles. To drive the Lykens and Trevorton laterals for the distance indicated, several construction shafts and slopes must be sunk to permit efficient and safe construction.

Jan 1, 1955

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By Y. K. Wong

This paper describes in detail various problems concerning the construction of a pile-raft foundation supporting a 42-storey tower block. The subsurface generally consists of highly weathered sedimentary rock. A comprehensive instrumentation program is implemented to monitor the behaviour of the foundation system throughout the construction period of the superstructure. Instrumentation observations are highlighted in the second half of the paper.

Jan 1, 2010

By B. W. Prof. Frazier

I PROPOSE in this paper to treat of the chimney merely as a heat engine, as one of the devices resorted to in practice for the conversion of heat into mechanical work. For the sake of simplicity and clearness in the discussion, let us consider the subject in its simplest form. Conceive a chamber, heated from without, in free communicatioH at one end with the external atmosphere, and at the other end opening into a vertical chimney. Let the. cross-section of the chamber be so great, relatively to that of the chimney, that we can neglect the actual energy of the air passing through the chamber. We will neglect, also, all passive resistances to the passage of the air. We will assume that the cross-section of the chimney is constant, and that the air in passing through it neither gains nor loses heat. The following symbols will be employed in the discussion : Po = the normal pressure of the atmosphere, which, it is assumed, is the pressure existing at the level of the chamber. Po = 10332.96 kilograms per square meter. P2 = the pressure of the external atmosphere at the top of the chimney. To = the, absolute temperature of melting ice by the centigrade scale. This is assumed to be the temperature of the external air at the level of the chamber. To = 273°. T2 =the absolute temperature of the air as it passes from the chamber to the chimney. T3 =the absolute temperature of the air as it issues from the chimney. to, t2, t3 are the temperatures, as recorded on the centigrade ther¬mometer, corresponding to the absolute temperatures To, T2, T3 re-spectively to = 0° C. In general, t = T- 273. Io, I2, I3, represent the intrinsic energy of the air at the temperatures To, T2, T3 respectively.

Jan 1, 1882

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2003

Management of Mining Wastes in European Union and Developments in Turkey

Sep 13, 2010

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

The Bureau of Mines is operated to assist in promoting economic development through increased efficiency in the mining, preparation, treatment, and utilization of mineral substances; to aid in conserving mineral resources through preventing waste; and to help the mining industry improve health conditions and increase safety. Accomplishment of those ends is sought through investigation of scientific, technologic, and economic problems of the, mineral industries and dissemination of resulting information. Building materials of mineral origin constitute an important product of mining, and the Bureau makes studies of these in the various fields mentioned. The following commodities come within this classification: Asbestos, anhydrite, asphalt, cement, clay and clay products, diatomite, dolomite, glass and mineral wool, granite, greenstone, gypsum, lightweight building materials, lime, limestone, magnesite, marble, sand, sand and gravel, sandstone, sand-lime brick, slate, soapstone, and trap rock.

Jan 1, 1937

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By Paul D. Klipfel

Introduction Mineral exploration interest, principally for gold, in the south-western Pacific has surged to new proportions. This is primarily due to the application of epithermal exploration concepts in the Australian-Oceana region. Other factors that have contributed to the high level of exploration interest include governmental policies supportive of mineral exploration, along with relative ease of tenure access and a relatively short bureaucratic process. This paper highlights exploration and development activities in the North Island of New Zealand, Fiji, Vanuatu, the Solomon Islands, and Papua New Guinea (Fig. 1). It provides a framework to understand the overall recent enthusiasm that has been brought to the south Pacific by explorationists. Through these recent developments, it is clear that the south Pacific region will become a significant gold producing area and thereby worthy of attention and study. Papua New Guinea alone is the free world's seventh largest producer (Table 1). And, with the addition of production from deposits presently being developed, this status is likely to be raised. History Gold was first noted on various Pacific islands in the late 1500s by Spanish explorers. They thought they had reached the legendary King Solomon mines. Since then, the history of prospecting in the southwest Pacific has coincided with the colonization of the region. Settlers in New Zealand extensively mined alluvial and lode gold deposits starting in the 1850s. The spread of European colonization to the more remote Pacific islands from 1880-1940 was accompanied by varying degrees of prospecting activity by planters, traders, and settlers. Some were successful, others may have been successful, but never returned due to hostile indigenous peoples or disease. In general, records of such prospecting activity are meager and exploration leads are, in some cases, gained through local village folk memory. Most early discoveries were alluvial finds. These led to placer operations, particularly in New Zealand, the Solomon Islands, and Papua New Guinea. Continued prospecting located lode deposits such as the Morobe Gold-field of Papua New Guinea, the Coromandel Peninsula of New Zealand, and the Emperor of Fiji. Some areas were prospected thoroughly. Yet others, such as Vanuatu, remained relatively unexplored until the present exploration surge began. During World War II, interest in minerals was diverted. It was renewed significantly until the middle 1960s and early 1970s when regional porphyry copper exploration was conducted.

Jan 10, 1987

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By G. Stokreef, B. R. Davis, M. Kadiyski, Alvear Montenegro, H-P. Loock, V. Montenegro

An optical probe for burner monitoring in copper flash smelting, first developed at the University of Concepcion, is being industrially tested in a collaboration between Kingston Process Metallurgy, Aurubis AG, and Queen’s University. The sensor uses fibre-optics and optical emission spectroscopy to analyze the light emitted from combusting particles in the furnace reaction shaft. Information that can be extracted from the emission spectrum includes the temperature and brightness of the flame, as well as emission lines or bands from excited atomic and/or molecular species. Laboratory proof of concept testing of the sensor was first completed in a continuously fed drop tube reactor using O2/S stoichiometric ratios between 0.8–4.0. These O2/S stoichiometries capture the industrial operating condition, which is typically less than 1. The results from lab testing justified a plant trial of the optical probe, which was done in the Aurubis Hamburg flash furnace in September 2018. From this trial, approximately 31 hours of spectral data were collected and synchronized with furnace operating data. The results from both drop tower test work and the plant trial are discussed with implications for process monitoring in the commercial furnace. INTRODUCTION Flash furnace smelting is a continuous feed, batch tap, pyrometallurgical process. It is used to treat copper sulphide concentrates and small amounts of secondary materials, such as dust generated by the process. O2 enriched air and the concentrate blend are fed into the furnace reaction shaft through the concentrate burner. As the particles fall through the reaction shaft, they heat up and ignite, causing rapid, exothermic reactions that oxidize the iron sulphide, some copper sulphide and impurities in the feed. Reacted particles fall into the settler of the furnace, melt and separate into a matte and slag, while the SO2 enriched off-gas is carried out of the furnace for heat recovery and H2SO4 production. Operation of the furnace is achieved by adjusting a limited number of control variables. The main variables are the blast feed rate, blast oxygen enrichment, SiO2 flux feed rate and CH4 combustion rate (CH4 is used when the chemical energy of the concentrate is low) all measured relative to a set feed throughput. (Davenport & Partelpoeg, 1987; Davenport, King, Schlesinger & Biswas, 2002) The batch tapping nature of flash furnaces makes operation difficult because these control variables impact each other, and product quality can only be measured when matte and slag are tapped from the furnace. This means that operation of a furnace is based on feedback control from matte and slag assays. Because of the time-delay associated with understanding product quality, there is interest in using technology to monitor the combustion reactions that happen in the furnace reaction shaft.

Jan 1, 2019

By J. D. Steenkamp

In a paper presented at the Heavy Minerals Conference 2001 a laboratory scale investigation on the beneficiation of an ilmenite containing waste stream by magnetizing roasting was reported1.This waste stream contained a high concentration of ilmenite, which was contaminated by chromite and other gangue minerals. Interpretation of the results of the investigation was based on the assumption that during magnetizing roasting of an ilmenite concentrate, under the oxidizing conditions, the magnetic properties of the chromite would remain constant. In this article the following hypothesis was tested: The magnetic susceptibility of chromite would remain constant during magnetizing roasting of an ilmenite concentrate under the oxidizing conditions reported by Gouws and Van Dyk1. The results of this study indicated that the hypothesis is not true. The increase in the magnetic susceptibility is not significant though and it is expected that it will not influence the final ilmenite quality to a large extent. Based on the assumptions that the bulk magnetic susceptibility of the waste stream samples represents that of the ilmenite in the waste stream, and the bulk magnetic susceptibility of UG1 chromite that of the chromite in the waste stream, the results also served to confirm that the waste stream with a high chromite content should be roasted under oxidizing conditions, in a reactor with a well-defined retention time distribution (i.e. a fluidized bed reactor), at a roasting temperature of 750°C (rather than the higher temperature ranges of 800°C and 850°C).

Jan 1, 2003

By E. J. Karges

[For reasons well known to Mining Engineers, fine grinding in the wet form is quite universal inn plants engaged in the traction of metallic values from crude ore In the processing, of non-metallic and industrial minerals, however, fine grinding in dry form is the more common method. The crude materials generally contain less moisture than required for wet grinding, and the products are usually marketed or used in the dry form, most of them as powders. To grind wet would therefore entail the addition of water and the expense for drying the product, which is not justified. This paper will concentrate on the particle size reduction or fine grinding of materials to produce a dry powder]

Jan 1, 1963

By D. Kachongo, Y. Cheng, A. Kashala, D. Samal, G. Mitshabu

Many copper processing flowsheets in the Democratic Republic of Congo include the leaching of oxide ores containing copper and cobalt, copper solvent extraction, copper electrowinning, and precipitation of cobalt salt. Recently, cobalt price gained momentum, driven mostly by the fast-growing electric vehicles battery market. The ore blending scenarios tend to prioritise high cobalt grade ore, whatever the content of copper and other impurities. Therefore, many copper solvent extraction circuits are running below design capacity. The variability of feed induces a variability of the leach solution with respect to copper, manganese, and silica contents. It is thus important to adjust hydrodynamic and metallurgical parameters of the solvent extraction plant to optimise metallurgical performance, production cost, and the quality of the copper electrolyte. This paper presents some results on how solvent extraction plant parameters have been managed in two solvent extraction plants running with lower than designed copper input. INTRODUCTION Referring to a report of the chamber of commerce of the Democratic Republic of Congo (DRC) the online publication Agence Ecofin (2019) indicated that the DRC ranks in the fifth position of the world top copper producing countries with over 1.2 million tons produced in 2018. The same year, 66% of the world’s cobalt was produced in the DRC at over 106,000 tons. If the political situation remained stable and the new tax regime introduced in 2018 did not deter private investors, copper production could reach 1.4 million tons/a in 2020 as pointed out in Mining.com (2019). Forecast figures for DRC cobalt production vary widely depending on analysts. The DRC online magazine Actualité.cd (2018) referring to a ministerial source forecasts over 141,000 t cobalt/a for 2020. The reality will depend on many factors, including the selling price, the supply compared to the demand, and finally the reaction of investors to the new DRC tax regime. The growing electric vehicle batteries market has been the major key driver of the price of cobalt. The five years historical cobalt price graph in figure 1 from infomine.com (2019) shows that the price of cobalt peaked at over 40 USD/lb in the first quarter of 2018. Cited by the online Magazine Creamer Media, Smith (2019) has indicated that the long-term demand of cobalt will likely remain strong.

Jan 1, 2019

Despite technological improvements and better understanding of the hazards, coal dust explosions stilI occur. Experimental explosions in galleries in various countries extend knowledge with the constant aim of providing safer working conditions. The inadvertent ignition of an accumulation of methane is the traditional initiator of the coal dust explosion.There are specific parameters of coal dust explosibility and explosion propagation, including the important volatile matter in the coal, fineness and dispersibility of the dust and its concentration. Accepting that initiation cannot be absolutely prevented, it is necessary to consider explosion suppression. While both limestone dust and water are the chosen explosion suppressants, in practice water has more limitations to its efficacy when related to the degree of explosion violence. These data give rise to the criteria for explosion suppression, differences in favoured mining geometries, and using the same principles, to differences in suppression treatments.

Jan 1, 1988

By R. Mensah-Biney

The NC State University Minerals Research Laboratory (MRL) and Waste Reduction Partners (WRP) of the Land of Sky Regional Council joined efforts in 2000 to initiate a technically sound and practical program for the management of high-volume coal combustion by-products (CCBs) in North Carolina. The accumulation of CCBs from coal burning boilers throughout the state of North Carolina posed a substantial storage problem, and the area was overripe for an effective management program, which would be environmentally sustainable. In particular, the public utility generators had filled storage ponds on their properties, and the storage overload had grown to critical proportions. Much the same situation existed for paper mill biosolids, which were stored on site in landfill cells along with daily output of CCBs from the mill boilers. A conversion process via the patented pyro-process12 (US Patent No. 5,342,442) to produce synthetic light weight aggregates (LWA) from CCBs and paper mill sludge was conceived to process large quantities of both these waste materials. MRL and WRP initiated and formed a consortium that brought together academia, private industry and state agencies to evaluate the production of LWA by the pyro-process. The industry partners included representatives from the power companies, industrial ash generators, expediters for coal ash products, as well as concrete block manufacturers. It was important to welcome interested parties from not only the western North Carolina area and other parts of the state but also from neighboring states including Tennessee, South Carolina and Georgia. Membership of this consortium evolved during the intervening years to include the following participants and supporters: Progress Energy Carolinas; Duke Energy; Santee Cooper; Full Circle Solutions; Land-of-Sky Regional Council; NC Department of Pollution Prevention and Environmental Assistance; Ecusta Business Development Center; Blue Ridge Paper Products; Jackson Paper and Manufacturing Company; Miller Perlite; Appalachian Products; General Shale Brick; Metromont Materials; Small Business Technology Development Center of the University of North Carolina system and North Carolina State University The initial development program conducted at the Minerals Research Laboratory (MRL) was to formulate an acceptable LWA product, which fulfilled user specifications for light weight concrete block and structural concrete application. Support work and program coordination efforts were furnished by retired technical volunteers in WRP. The work advanced steadily, using proven technologies well established in the mineral industry, to generate a very satisfactory LWA. The consortium then concluded that a more comprehensive CCB conversion program would have more appeal for full scale manufacture and commercialization, if a variety of products from CCB separation were generated. This product assortment would include bottom ash, low carbon fly ash, recovered carbon of high purity, as well as the synthetic LWA. The bottom ash would serve the concrete block market, the fly ash was in demand for ready-mix concrete, and the high carbon product could be pelletized and used as a fuel for reburn or by the steel industry, and the LWA was a sought-after component for light weight concrete applications. After scouting all these potential markets and finding them to be viable, the consortium then inaugurated an integrated pilot plant program for the CCB separation and conversion. The plan was organized in three (3) parts: (1) Phase I ? bench scale evaluation studies (2) Phase II continuous pilot plant evaluation and (3) Phase III ? conceptual commercial plant design including marketing efforts and attraction of business entrepreneurs to build a full scale manufacturing plant. Phase II would serve to validate the process in a continuous mode and produce substantial quantities of products for preliminary marketing efforts and for demonstration-of-use purposes. The consortium agreed to the name, CAROLINA ASH PRODUCTS, (CAP), for the integrated pilot plant program. The products generated might be designated with the CAP label as: bottom ash would be named CAP Granules, low carbon fly ash would become CAP Ash, recovered high carbon product would be CAP Carbon, and LWA would have the name CAP Stone. Phase II of the program processed 20 tons (18 t) of ponded ash from Progress Energy storage at a rate of 600 lb (271 kg) of raw ash per hour with favorable results. PRELIMINARY STUDIES Prior to committing laboratory research and development effort as well as support and coordination activities to this program, it was necessary to determine (1) the level of need for a freshly launched CCB reutilization program in this state and (2) what degree of versatility was necessary for such a process. State agency records and a survey of recent boiler operations indicated that in the state of North Carolina at least 77 facilities manage CCBs from their boiler operations. Despite continuing development efforts in more eastern parts of the state, the use of CCBs for commercial applications has not increased to a level which alleviates the need to store vast quantities in private monofills on the generator?s property. More than 1.25 million tons (1.13 million t) of CCBs are landfilled in NC annually, with 300,000 tons (271,985 t) per year generated in western NC alone. Many different boiler types, which span both very old units and those that are modern and efficient, were to be found. These included stoker-fired units, pulverized coal boilers, slag-tap furnaces, and fluidized bed combustion boilers covering a range of sizes. Any systems designed to separate CCB components from all these sources and convert them to useful secondary products would need broad processing latitude and flexibility. Up to the present there has been a paucity of research done in the western part of the state to find productive alternatives to storage in landfills. With tipping fees in our largest landfill now approaching $40 per ton ($44 per t) and escalating transportation fees (about $200 per truckload up to 40 tons, traveling a distance of 25 miles), the problem has become urgent both economically and ecologically. A well-designed, integrated wet process for CCB separation into value-added products had much potential to be less expensive than landfilling as well as to provide saleable materials with acceptable profit margins. These preliminary investigations also revealed that other major waste streams, in particular paper mill sludge and municipal and animal waste biosolids were important candidates for priority attention. Since these biosolids could furnish the organic component of a synthetic LWA product, they could be consumed as part of the same program. This added interest value to a growing list of partners to support and participate in the program.

Jan 1, 2009