Search Documents

By E. G. Davis

The Bureau of Mines investigated gaseous direct reduction of low-grade iron ore concentrates in a continuous fluid-bed reactor. These studies were made in a 4-inch diameter fluid-bed reactor using hydrogen alone, and oxygen-or air-reformed natural gas as the reductants. The percent reduction is directly dependent on the mole ratio of hydrogen in the reducing gas to the oxygen associated with the iron oxide in the ore. Two-and three-stage fluid bed tests were simulated by repeated continuous tests. The results showed that percent reduction of the final product was dependent on the mole ratio of the quantity of hydrogen in the gas of each stage to oxygen in the iron oxide of the initial ore feed. Reduction as high as 87 percent in the single stages and as high as 94 percent in the multistages was obtained when either hydrogen or reformed natural gas was used as the reducing gas. Magnetic separation and concentration of the highly reduced fluid-bed product yielded a high metallic iron concentrate analyzing 85 percent total iron and 80 percent metallic iron with total iron recovery as great as 90 percent. Agglomeration of the high-grade metallized concentrate produced hard pellets analyzing 85 percent total iron and 78 percent metallic iron. Green pellets, with good strength, were made without any binder in a drum pelletizer. Direct melting of the high-metallic fluid-bed product in a basic lined arc furnace produced a nearly pure iron which contained 0.09 C and 0.01 P with 95 percent recovery of the metallic iron in the metal.

Jan 1, 1972

By Jerome Apt

This report presents the methods and results performed pursuant to the U. S. Bureau of Mines contract entitled "Noise Abatement in Mining Machinery," Number H0122054. 2.1 Background Until the Congress of the United States created and passed Public Law 91-173, the Federal Coal Mine Health and Safety Act of 1969, there were no directly-applicable standards for noise exposure for underground coal miners.1 Section 206 of this law, approved December 30, 1969, provided for standards of noise to be applicable to each coal mine. It is as follows:

Jan 1, 1975

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

By C. Lumley

The management of the Anglo Platinum (AP) mining technical systems (MTS) embarked upon a process of defining the strategy for the MTS department. The newly established department forms part of the greater Group Information Technology (IT). The strategic process took place within an environment that had witnessed a dramatic proliferation of IT implementations across the group within the last three years. The IT department has been structured in terms of the classical plan, build and run functions with the applications and integration streams running perpendicular across these three functions. The application stream is divided into commercial and mining technical systems with business systems integration the third stream. The mining technical systems department supports mine management to effectively gather, analyse and disseminate data relating to the ore reserve by integrating a number of strategically selected IT applications to ensure that the safety, legal and operational requirements are met. This service to business is rendered by management of a strategic outsource partner via tightly controlled service level agreements (SLAs). The framework used for creating a mining technical systems department that is empowered to add value to business was formulated using the AP value chain as both the starting point and guiding process to ensure alignment to the greater internal strategy of the business. Keywords: Platinum, Mine planning, Mining technical systems, Value chain.

Jan 1, 2003

By Silvana Costa

In the last two decades, there have been nearly no new mining towns built in Canada. Governments and mining companies have viewed long distance commuting (LDC), commonly known as fly-in-flyout or fly-in mines, as a way to avoid problems associated with building a new community and providing for its sustainability after mine closure. LDC is also considered more cost-effective than building a mine town. The intensification of the use of LDC in the Canadian mining sector has been quite rapid, particularly in northern regions. However, LDC has implications to employees, their families and communities, which deserve further examination, particularly considering the significant expansion in Northern mining and Aboriginal participation in this sector. This paper presents a review of the major issues in long distance commuting, both from an industry and community perspectives. It is a result of preliminary investigation for a PhD research project that will be pursued by a Bridge Fellow and UBC Mining Sustainability Working Group member, and guided by an interdisciplinary research team at the University of British Columbia (UBC). The Bridge Fellowship Program is research-training program linking the UBC?s Faculties of Medicine, Engineering and Graduate Studies. Its mission is to develop creative evidence-based prevention measures for public, environmental and occupational health problems. The SWG is an interdisciplinary student group based in the UBC Department of Mining Engineering, committed to respond to the complex sustainability-related challenges currently faced by the mining industry. In other to pursue this project, it is paramount that industry and local communities alike participate in the development and clarification of research questions as well as in the research design. It is hoped that this paper will function as an invitation for industrial and community partners for such study. The main themes identified for this research are occupational health and safety of LDC employees, family life impacts and community health impacts of this model of resource development.

May 1, 2004

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By S Worden, A Lee Zhi Yi, E Sellers, G Corder, A Littleboy

The global shift towards decarbonisation is driving competition for the extraction of critical minerals such as nickel, lithium, and copper. To meet this demand, new mines are being developed while mines approaching closure are being reimagined as sites of potential resources. This reimagining challenges how mine closure is being conceptualised. In the conventional case, when a mine reaches the end of its economic life, it is closed or put into care and maintenance until it transitions to the next land use, such as agriculture, native ecosystem corridors, solar farms or integrated eco – precincts (Murphy et al, 2019; Holcombe, 2020) (the authors acknowledge that unplanned mine closures have left a devastating legacy of contamination, safety and cultural heritage impacts). Extracting minerals from closed or closing mines will extend mine life and, therefore, delay relinquishment and transition. In this context, innovative technologies are needed to make mining economically viable. In the first year of her doctoral research on improving stakeholder engagement in mine transitions, Lee Zhi Yi has coined the term ‘mine life extension technologies’ (MLETs) to describe a class of technological solutions that optimise extraction of resources after a mine reaches the end of its economic life. Examples of MLETs include agromining (van der Ent et al, 2015), in situ recovery (Robinson and Kuhar, 2018), and reprocessing or reuse of tailings (Gou, Zhou and Then, 2019). MLET extraction offers several benefits compared with conventional mining processes, such as waste remediation, value recovery of minerals, a smaller footprint and less environmental impacts (Sellers, Picorelli and Salmi, 2022). What requires further investigation is the consequences of MLET implementation to host communities or community perspectives towards the proposed technology and subsequent delays in transition.

Aug 2, 2023

By A. Baldwin

This report describes the engineering feasibility and economic advantages of a unique new mining machine using cutting bits that take a constant-depth linear cut in the coal face. The studies show that this innovative new cutting concept, being developed by the Bureau of Mines, can be designed into the basic continuous mining machine. The resulting miner would be attractive to mine owners because coal could be mined with minimum generation of airborne respirable dust, substantial increases in productivity, and elimination of methane ignition due to cutting.

Jan 1, 1977

By V. R. Spironello

The Bureau of Mines is involved in research directed toward the conserva¬tion of important raw materials and the utilization of solid waste. Two of the objectives are to conserve high-quality coking coals used for foundry coke and to utilize waste materials of marginal quality but of high calorific value. These objectives are consistent with Bureau goals. Pilot plant cupola trials were made to evaluate the adequacy of various alternative fuels, and to determine to what extent they could replace the foundry coke in cupola charges. Information was obtained on furnace performance, metal and slag chemistry, environmental questions, and the properties of castings. It was shown that anthracite or bituminous coals can partially replace charge coke up to the 40 pet level. Briquetted materials prepared from fuel fines, and waste prod¬ucts or byproducts of high calorific value, all tend to break down on heating in a cupola so that their use must be restricted to below 20 pet replacement. In cases where pitch-bonded coal fines or petroleum coke were used, carbon pickup by the iron was inadequate for gray iron specifications. Although emphasis during this work was placed on basic slag practice, some acid practice results are included.

Jan 1, 1980

By P Papanastasiou, J Hadjigeorgiou, E Kyriakou

The south west area of Cyprus has a long history of slope instability problems. The location and extent of these landslides has been influenced by ground morphology, geological structure and the presence of weak rocks and cohesive soils. The main triggering mechanisms have been precipitation and/or seismic events. Landslides have contributed to the decision to relocate villages and considerable efforts have been put into maintaining the integrity of the local transportation network. This paper uses a recent case study of road embankment failure near Pentalia in southwest Cyprus to review the available tools for the analysis of slope instability. It further demonstrates how the shear strength reduction technique can be used in a finite element analysis to better visualise the slope instability mechanism of a road embankment and provide a reliable tool in selecting appropriate remedial measures.

Jan 1, 2006

By Paul H. Lu

This Bureau of Mines report summarizes the analysis and eveluation of the field measurement results of a comprehensive ground control study conducted in a mechanized longwall coal mine in West Virginia. Emphasis is placed on the three basic ground control parameters: ground pressure, ground movement, and geomechanical properties. Specific topics include premining ground pressures, front-abutment pressure in the longwall panel, histories of pillar loading, differential roof-strata movement and bed separation, differential floor strata movement, entry roof-to-floor convergence, in situ moduli of rigidity of coal seam and roof and floor strata, and mechanical properties of coal and coal measures rocks.

Jan 1, 1985

A thermochemical model is developed to study the two-stage smelting reduction process for ironmaking without post-combustion. Steady-state multi-material and heat balance equations are solved simultaneously to study the effect of metallisation, slag basicity, coal rank and heat loss on consumption rates of coal, ore, flux and oxygen and production rate of slag to produce hot metal of a given composition, tapped at a given temperature. The model is applied to the commercial data for a COREX-plant producing a wide range of hot metal compositions, tapped at different temperatures. The computed rates of coal, slag, flux, ore and oxygen were found to be close to the reported ones, but an exact match could not be obtained. It is found that a four per cent change in metallisation brings changes the coal rate by five per cent, flux rate by six per cent, slag rate by eight per cent and oxygen rate by 13 per cent, while a ten per cent change in basicity changes the coal rate by ten per cent, flux rate by 13 per cent and oxygen rate by 22 per cent. Further, it is found that an increase in metallisation decreases the coal rate and export gas. At a given per cent metallisation, the coal rate and the export gas are lowest for anthracite compared to all other types of coal.

Jan 1, 1999

By Pierre L. Labelle

Non electric Dual Delay initiators have revolutionized many aspects of underground mining. The units are used in all types of underground blasting operations. Some operations, due to the complexity and variety of their blasts, have extremely large inventories of conventional non electric products. The Dual Delay system has drastically reduced these inventories and has added an important element of versatility to blast designs.

Jan 1, 1994

By D Cumming-Potvin, S W. Jacobsz and E Kearsley, J Wesseloo

This paper describes a physical modelling program that recreated block cave propagation in a geotechnical centrifuge. A brief description of the design of the test along with the sample material and monitoring equipment is given. The samples tested showed caving behaviour and fragmentation distributions that one would expect from caving mines, with one cave deviating due to pre-existing major discontinuities in the sample. A series of fractures formed ahead of and parallel to the cave, implying that an extensional failure mechanism may play a larger role in cave development than previously thought. The results of acoustic emission monitoring of the tests show a seismogenic zone advancing ahead of the cave; however, the quantity and quality of the data is too limited to draw any further conclusions.CITATION:Cumming-Potvin, D, Wesseloo, J, Jacobsz, S W and Kearsley, E, 2016. Results from physical models of block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 329–340 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

An underground mine disaster is an accident of major proportions that takes a significant toll in human lives. A disaster usually disrupts the normal functioning of a mine and may result in entrapment of miners whose normal egress from the mine is cut off. A disaster often necessitates a rescue operation and a means of keeping the trapped miners alive while they await rescue. Explosion, fire, inundation of water or toxic gases, and collapse of a major portion of a mine are among the causes of mine disasters. Miners threatened by such an occurence must either bring the situation under control (e.g., by extinguishing a fire) or remove themselves from the danger. If control is unsuccessful, they must retreat to a place of safety. Four different activities may be involved: evacuation, escape, survival, and rescue. Evacuation is the orderly exit of people from the mine using previously identified escapeways and following a previously determined evacuation plan. Miners whose normal evacuation routes are blocked may be able to find alternative exit routes and escape by their own efforts. For those who cannot, the issue becomes survival while waiting to be rescued. The survival period may last for many days while rescue efforts are mounted from outside the mine.

Jan 1, 1981

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

Coal has become an enormously important export industry. Owing to a range of mainly natural advantages, Australia has been able to almost treble its exports in a little over the last decade. Australia is now the world's second largest exporter and coal is now the nation's largest single export earner.Despite this very significant growth, Australia's competitive position is in jeopardy.

Jan 1, 1984

By P M. Bradbury

The nature of aggressive process chemical requirements typically in the Platinum Refinery Industries, lend themselves to the use of Polymer Composite Glass Reinforced plastics for pipework and other associated equipment in these types of Plants. This paper discusses the basic characteristics of a Polymer Composite glass reinforced piping system and gives sample examples of applications in current present day use.

Jan 1, 2006

By Driver R. C, Moelle K. H R

This paper is dedicated to the memory of our friend Peter McKenzie who contributed much to the knowledge of the New South Wales Coalfields.ABSTRACTA fossil river system was recently mapped over parts of the Southern Coalfield, N.S.W. This river system occurs in the roof strata of the Bulli Seam. Sandstone of a fluvial nature was deposited in its course. The sandstone exhibits strong sedimentary vectorial properties and has a marked influence on strata-control in colliery workings.The sedimentary features analysed indicate an approximate S200W flow direction. Petrological studies reveal a clastic, well-cemented sedimentologically and structurally anistropic rock type. Washouts have been found and isopach maps of both sandstone and underlying roof-strata have been compiled. Relevant measurements were carried out in existing colliery workings and on bore cores.Optical determinations of feldspars revealed the presence of plagiocIase feldspars with few exceptions. Most of the feldspars are altered to clay minerals. It was found that a geographical trend exists in the distribution of feldspars, with more basic plagioclase in the northern part of the field.The source area of the fluvial sandstone lies to the north of the Southern Coalfield.Petrofabric analyses were done on several specimens of the fluvial sandstone. In the vicinity of major disturbances, penetrative fabrics were discovered.Calcites (e, 0112), micas (001), and quartz (crystalIo graphic c) show preferred orientations.

Jan 1, 1967

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009