Search Documents

By D. D. Ndenguma

This investigation compares the results from an experimental and numerical study of air flow in a scaled-down underground coal mine model. This was done in order to determine if numerical analysis can be relied upon when searching for ventilation solutions to control high concentration of coal dust and methane gas in underground coal mines. Steady state analyses were used to identify flow patterns and recirculation regions within the mining section while transient state analyses were used to determine the time taken to extract the initial air from the model. The agreement between the experimental and numerical results indicates that numerical modelling is useful in this regard. The study went further to devise a method of determining the optimum position of the jet fan that is responsible for mine-gas dilution at different stages of mining.

Jan 1, 2014

By John E. Rourke, O&apos

This paper describes some of the results of a project for the design and demonstration of subsidence monitoring systems for underground coal mines. The project was designed to test monitoring systems described in an earlier feasibility report (O'Rourke and others, 1979). General objectives of the project were to develop reliable cost- effective monitoring systems for use above caving- type mining operations, over supported mines, and in urban undermined areas. Topics selected for discussion in this paper include a description of the instrumentation systems, the site conditions, problems of installation, resulting recommendations and an over- view of subsidence performance data obtained. There were some particularly difficult problems of installation to overcome at this site. Some of these could be experienced at any surface or under- ground project, others are probably more directly related to Western coal fields. Almost any subsidence monitoring program may face the following difficulties:

Jan 1, 1982

By Zdzislaw Specht

THIS paper discusses elementary laws pertaining to seismic reflection methods and presents a general and simple criterion for determining the direction of dipping of a reflection horizon from observational data of distance and time. The important development of practical geophysics and the successful results obtained in America, Germany, and other countries, caused introduction of geophysical methods of prospecting in Poland. Of all methods, seismic prospecting has proved most successful in the area of the Carpathian foreland, where new oil reserves are to be expected. Because of the great depth of the sedimentary column in that area, rang-ing sometimes over 2000 meters, it was obvious that only the seismic reflection method could give reliable information regarding the structural features of these strata at such a depth. During the experimental surveys it appeared that the complicated geological conditions of that area do not always allow prediction of the depth and the angle of dipping of reflecting horizons, and for that reason information about the inclination of a given horizon has great importance in the determination of subsurface structure. Therefore the problem arises of obtaining from seismic reflection data reliable information as to the direction of dipping of reflecting strata, without any previous knowledge of the average velocity and depth of geologic horizons under consideration.

Jan 1, 1940

By S. Viswanathan, A. S. Sabau

"Dimensional changes between a pattern die and its corresponding investment casting part occur as a result of complex phenomena such as thermal expansion/contraction and hot deformation (elastic, plastic, and creep) during the processing of the pattern material (wax), mold material (shell) and solidifying alloy. Determining the pattern tooling dimensions is crucial to the dimensional control of the investment casting process. To date, computational methodologies have not been applied to the prediction of dimensional changes in investment castings.This paper deals with the evaluation of wax pattern dimensions, which is one important factor in determining pattern tooling dimensions in investment casting. Cerita 29-51, an industrial wax, is considered in this study. The wax pattern dimensions are determined by considering its thermo physical and thermomechanical properties, restraint of geometrical features by the metal die, and process parameters such as dwell time, platen temperature, injection pressure, and injection temperature.IntroductionThe investment casting process involves making a disposable wax pattern by injecting wax into a metal mold, building a ceramic shell mold around the wax pattern by the application of a series of ceramic coatings to the wax pattern, dewaxing the ceramic shell mold, and casting the alloy into the shell mold. Dimensional changes between the pattern tooling and its corresponding cast part occur as a result of thermal expansion, shrinkage, hot deformation, and creep of the pattern .material (wax), mold material (shell), and solidifying alloy during the processing [1]."

Jan 1, 2001

Appropriate roof control is the most important requirement in underground coal mining and, in the case of longwall panels or second mining in room and pillar extractions, this can be simply expressed in terms of good and predictable roof caveability. Studies of roof caveability have been undertaken in many coalfields around the world. Most of their conclusions. however, are directly related to the mining and geological conditions experienced in these areas and as a result, may not be applicable to the conditions encountered in the Appalachian coalfield. Furthermore, some of these studies appear to be theoretical and conceptual, ignoring many important parameters of the geological environment, whereas others rely heavily on geological information but lack a rigorous foundations upon which quantitative design guidelines can be built. The objective of this study is to analyze caving and mass deformation characteristics above longwall panels in Appalachia and includes: - Analysis of the effects of the geological and geomechanical characteristics of the strata on the caving height and the bulking of the caved-material. - Testing of the applicability of the various theoretical and empirical models of roof caving. Formulation of a numerical around- deformation model for ion-elastic material behavior.

Jan 1, 1986

By M. Jele

? Sulphuric acid plant in umbogintwini. ? Double absorption plant, capacity of 550MTPD. ? Build by simon curve during the year 1973. ? Side stream plants such as: ? Liquid SO2 Plant, ? Liquid SO3 and ? Oleum plant

Jan 1, 2009

By Klaus Rieker

The main train station of Leipzig in Germany is currently being upgraded from a head station to a partially thru station. In order to achieve this, significant ground improvements are necessary. Soil freezing for example is used to create the excavation box retaining walls. The freezing works will be carried out from two tunnels with an inner diameter of 2.4 m (~ 8ft). The tunnels were constructed by the pipe jacking method. The cutter head of the machine was equipped with discs and scrapers. Driving and excavation was carried out using a bentonite supported face. Due to the small arrival shafts, the machine had to be lifted out in components. The essential limitation of settlements during the drives was achieved even better than expected.

Jan 1, 2008

By K. A. Clark

SEPARATION of the oil from the bituminons sands of the Athabaska area of Alberta has been a subject of study by the Research Council of Alberta. The results of the study have been published in the Annual Reports of the Council. However, the last Annual Report in which there is mention of bituminons sand separation is that for 1934. The attention that is being directed toward the bituminons sands at the present time calls for an up-to-date summary of the work of the Research Council of Alberta on the hot-water separation process. STATEMENT OF FUNDAMENTALS OF HOT-WATER PROCESS Studies of the hot-water separation process have been largely empirical in nature. The objective sought has been a complete recovery of oil from the sand in the form of a separated oil which, itself, is free from mineral matter. Various procedures have been tried in the hope of attaining this objective and a very considerable mass of observations and background of experience have been acquired. lt is rime that a theory for hot-water separation should commence to emerge. As a start toward the formulation of such a theory, the statements which follow regarding the constitution of bituminons sand and its reactions with water and air are presented. It is not pretended that they are entirely correct, but it is believed that they lie not far from the truth. (1) Bituminons sand is an aggregate of sand, clay, oil, and water. The sand consists mainly of quartz particles of 100 ta 200 mesh size and smaller, but also of particles of other minerais including mica, rutile, ilmenite, tour-maline, zircon, spinel, garnet, pyrite, and lignite. Clay occurs interbedded with the bituminons sand, of which, also, it is a constituent. lronstone nodules of all sizes up to eight inches in diameter are likely to be present in the bituminons sand beds. The oil is viscous, naphthenic, and of a specific gravity slightly greater than that of water. The oil content ranges up to, and sometimes even exceeds, 17 per cent by weight. Rich bituminons sand from beds not invaded by water has a water content of 3 to 5 per cent by weight. The water is probably present as a film around the sand particles. The oil surrounds the moist sand grains as an envelope. (2) Water wets quartz and other siliceous minerals more readily than does mineral oil. Consequently, water tends to displace the oil film surrounding the quartz and other siliceous particles when the bituminons sand is mixed with water. Whether the oil is completely displaced depends on the properties of the water. That is to say, the materials dissolved or suspended in the water modify its wetting properties.

Jan 1, 1944

By O Haavisto, N Khajehzadeh, L Koresaar

Online analysis of metal content can be used to optimise the grade and recovery of a flotation circuit. Compared to conventional laboratory analyses, the benefit of an online analyser is the speed of the measurement, therefore disturbances (eg changes in feed grade and decrease in recovery) can be reacted to in real time by an operator or automatic process control system. In some cases traditional X-ray fluorescence analysers can be applied to silica analysis in iron ore when the SiO2 grades are high enough and have a negative correlation with iron; however, generally a laser-induced breakdown spectroscopy (LIBS) analyser is more suitable for low Z elements.The Outotec Courier 8® analyser is a LIBS based analyser able to measure elements starting from lithium (Z = 3), thus being able to measure impurities; eg silica and aluminium directly in iron ore slurries. Besides online elemental analysis, the analyser can be combined with optical measurements for rapid continuous measurement of each sample line. Laboratory testing has also shown potential for mineralogical analysis using the combination of LIBS and reflectance spectroscopy.CITATION:Koresaar, L, Khajehzadeh, N, Haavisto, O and Timperi, J, 2017. Online elemental and mineral measurement of slurries in iron ore beneficiation, in Proceedings Iron Ore 2017, pp 561–566 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Antonio De Biase

In October 2006, a 7m Double Shield TBM, boring through very poor volcanic formations, was pushed back by fluid mud, which presence had not been detected during previous field investigations, due to the high covers characterizing the majority of the tunnel axis. The present work describes the investigations made to gain better knowledge of the conditions in front and all around the TBM, the special measures implemented, the exploratory and bypass tunnels excavated, the extraordinary occurrences came true during the execution of these tunnels, the drainage campaigns, the design of the chamber excavated to free the TBM, the dismounting and restarting of the TBM.

By J. M. Stuve

The present Bureau of Mines investigation measured low-temperature heat capacities of NiBr2 (8 to 302 K) and NiS04 (9 to 70 K) by adiabatic calorimetry. The standard entropies (S°, 298.15 K) of NiBr2 and NiS04 were calculated as 29.26 ± 0.06 cal/deg mole and 24.21 0.04 cal/deg mole, respectively. (1 cal = 4.1840 joules.) Heat-of-solution measurements of anhydrous NiBr2 were used to determine its enthalpy of formation (?Hf°, 298.15 K) as -50.64 ± 0.31 kcal/mole. High-temperature enthalpies of NiBr2 and NiS04 were measured by drop calorimetry to 1,150 K and 1,002 K, respectively. Enthalpies, heat capacities, and related formation functions are tabulated to 1,200 K.

Jan 1, 1978

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By N. Paas

Diesel powered equipment has been operated in underground coal fir mare than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trine, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment. The operation if diesel powered equipment is not without challenges. Diesel engines generate exhaust emissions, in particular carbon monoxide, oxides of nitrogen, sulfur dioxide, unburned hydrocarbons, and diesel particulate matter that must be maintained at safe levels. The chief method to control ambient exposure has been dilution by ventilation. A new concept to ensure continued safe ambient emissions levels from diesel equipment in underground mines is the EMISSIONS MANAGEMENT PROGRAM™. The program encompasses all factors that will influence diesel emissions. By ESTABLISHING low tailpipe emissions through technology, such as clean engines, clean fuel selection, exhaust aftertreatment devices and filtration of the exhaust gases via the Dry System ™, this program ensures that the baseline emissions are at their lowest technically feasible concentrations. The DST Dry System™ exhaust conditioner reduces DPM by over 98%, as demonstrated through laboratory research at the West Virginia University. Carbon monoxide and hydrocarbon emissions and odor are similarly reduced. MAINTAINING these low emissions requires an expanded training program for operators and mechanics, onboard feed-back devices and a maintenance program with special focus on events and faults that can alter emissions. Finally, an on-board emissions sampling system allows the mechanic to VERIFY emissions levels and help diagnose engine faults. If the tailpipe emissions fall outside an established limit for a particular equipment, corrective actions will be initiated.

Feb 24, 1997

By Danell. R. E.

A drill monitoring system has been developed which measures performance characteristics of a rotary drill and relates this to the material strength and rotary specific energy. The drill monitor is computer based and is used to produce a profile of the relative in-situ material strength as a function of depth. This information has been used in determining the placement of explosive in selective loading of blastholes and estimating the amount of lump product in a particular section of an ore body.

Jan 1, 1989

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

By R. F. Shurtz

The problem of estimating the precision of systematic samples from a mineral deposit is attacked by interpolating the quality, or other attribute measured, by using Fourier approximation. Such approximation using trigonometric functions yields a particularly simple expression for the variance of the mean value of the attribute sampled. The increasing volume of publication in which the science of statistics has been applied to the problem of predicting the quality of an ore deposit from sets of samples taken from it might lead one to believe that engineering judgment can be replaced by statistics. There is, in fact, an implicit application of the principle of indifference or of "no advance knowledge" which has been discredited in modern statistical theory and practice. These pages will show that it is not always advantageous, efficient, or safe to apply this principle. This problem will be dealt with by using series of orthonormal functions to describe the distribution of the quality of ore in space as contrasted with the more commonly used distribution of quality as a frequency function. Mining engineers are rarely well acquainted with the use of such series or of the functions comprising them. These uses are commonplace in the fields of communication and information theory and it is not surprising that applications taken from these fields should be found appropriate for the analysis of the information contained in a set of samples from an ore deposit. It is hoped that presentation of the following basic, but incomplete, results will generate wider interest in this method and a fuller development of it as well as of the necessary computational techniques. FUNDAMENTAL PREMISES Random variables in the strictest sense are not very common in mine sampling. The sets of samples are almost always taken systematically and are, hence, not subject to all the laws governing random events. Therefore, unless there is indeed random experimental error in the determinations of quality, the treatment of systematic samples of n members as though they were random samples of n members often leads to calculation of confidence limits for the mean quality which are larger than they should be with the result that unnecessary additional sampling is done. The reason for this will emerge in the following discussion leading to Eq. 24 and its generalization. In order to inquire into such questions on a rigorous basis and at the same time avoid arithmetic complications that would obscure the concepts involved, a one dimensional distribution of quality will be assumed. The quality, Q, in suitable units is expressed as a function of the distance, x, along some straight traverse of the deposit. Such a function

Jan 1, 1967

By R J. In, C Moore, P J. Moffitt, T Hansen

Telfer Gold Mine combines a world-class gold and copper resource and longevity of operation as a major gold and copper producer. Telfer Gold Mine has undergone a series of transformations since mining commenced as a high-grade narrow-vein oxide open pit operation in 1977. In 1986, the open pit operation converted from a narrow-vein, high-grade operation, to a low-grade high-volume oxide mining operation utilising dump leach processing technology. Mechanised underground mining of the high-grade narrow-veins commenced in 1990. Total recovered gold production between 1977 to 1999 has totalled 5.7 million ounces. The Telfer Extension Project consists of two pre-feasibility studies, the Surface Extension Project (SEP) and the I-Series Project (ISP). The combined studies represent one of the more significant resource evaluations undertaken in the gold industry in recent times. Geological activities for the SEP pre-feasibility study have included the drill definition of a large low-grade resource within an area of 25 km2 . The surface drilling program has completed 15 000 metres of HQ3 diamond drilling and over 30 000 metres of RC between last quarter of 1998 and late-1999. The ISP pre-feasibility study is currently evaluating the resource potential of both a high-grade low-volume and a lower grade bulk mining scenario, 800 m to 1200 m below the surface of Main Dome. 15 000 metres of underground diamond drilling have been completed between last quarter of 1998 and August 1999 as part of this study. Systems and cultures have been developed to maximise safety, monitor the quality assurance/quality control (QA/QC) on all aspects of the operation, and minimise impact on the environment. All data are stored in database systems, specifically designed for Telfer operations. 3D geostatistical resource estimation using ordinary kriging has been carried out for over 220 geological domains within the 25 km3 of mineralised system. Non-linear geostatistical techniques are being investigated as part of the pre-feasibility study.

Jan 1, 2000

By David Heyl

"El presente texto señala la evolución de los modelos genéticos de geología económica del yacimiento minero Tres Cruces. Dicho yacimiento se encuentra localizado en el noreste del Perú, adyacente al distrito minero de Quiruvilca. A partir del año 1995 se le reconoció como el mayor productor de oro a través de un programa de exploración en la Formación volcánica Calipuy. Posteriormente, el yacimiento fue visitado por variosgeólogos que postularon diferentes modelos genéticos del yacimiento para así estimar su potencial económico -en tanto se incrementaron los datos geológicos del yacimiento. Por ello, el texto presenta el modelo genético de Tres Cruces, como el más adecuado, aunque la evaluación de su potencial econornica está aún en progreso."

Apr 26, 1999