Search Documents

This summary of State laws on explosives wag compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and, in general, how they have been treated. It does not Include any legislation passed after 1942, or any proclamations, regulations, or administrative orders. It does not purport or attempt to be authoritative. If any problem arises involving interpretation of the statutes of any particular State, the original source must be consulted for the exact words used by the legislature. This summary, however, will be useful in determining whether relevant statutes exist, and in locating them quickly, with a minimum of effort. It will be of value also in comparing statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject. To make these comparisons easier, the statutory provisions for each State have been grouped under several major topics in outline form. Although this sometimes has resulted in disruption of the continuity of individual acts, the increased general clarity and availability of comparable sections have more than justified the procedure followed.

Jan 1, 1943

By J. E. Terry

This paper outlines the steps that are being taken to close the gap between training and industry and indicates areas in which more work needs to be done. Although based on experience in the Maritime Provinces, it is applicable to industrial and educational studies across the length and breadth of Canada.

Jan 1, 1970

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By Robert H. Peters

This U.S. Bureau of Mines report identifies the types of serious accidents that occur most frequently at small underground coal mines and describes the strategies that could help prevent these accidents. A wide variety of methods for improving safety are suggested, including improvements in the design of equipment, work procedures, work schedules, safety programs, and emergency response plans, as well as techniques for diagnosing the potential hazards associated with new technologies and work procedures. Some of the papers in this volume focus on preventing specific types of mining accidents-ones associated with materials handling (primarily back injuries), equipment maintenance, improper machine guarding, and ground failure during retreat mining. Although the recommendations in this volume are heavily influenced by research performed at underground coal mines in the Appalachian coalfields, most of the papers contain advice that is equally pertinent to almost any type of mine.

Jan 1, 1994

By R. S. Dean

T HE theory of hardening by heat treatment was, as usual, the most actively discussed phase of metal working theory and in spite of the fact that it is now ten years since the dispersion theory was proposed by Messrs. Merica, Waltenberg, and Scott, it still retains a dominating influence. It is being increasingly recognized. however, that in its simplest form, that is, the purely mechanical effect of very fine crystallites distributed through a groundmass, it is distinctly in- adequate. To explain the observed facts we are obliged to assume some well-defined intermediate stage between supercooled solid solution and conglomerate, however fine be the particles of the latter. This intermediate has been inferred by Gaylor and Preston to be "the rejection of the atoms of the dissolved metal from the lattice of the solid solution accompanied by the possible formation of molecules."' Perhaps this may well be designated as the formation of supersaturated solid solution. Some very definite evidence of such an inter- mediate stage has been found in the hardening of steel where it appears that the very hard martensite may be considered as a supersaturated solution of carbon in a iron. The X-ray spectrometry of drastically quenched steel shows a tetragonal lattice whose parameter changes by tempering at 100" until it coincides with the cubic lattice of iron.? The same gradual change of the tetragonal to the cubic lattice has been observed by Sekito when esamining layers on increasing depth below the surface of a quenched carbon steel.

Jan 1, 1930

By L. J. E. Hofer

"INTRODUCTION This paper is riot to be considered a complete survey of data on carbides; it is only an attempt to correlate the more reliable of the existing data of interest in connection with the Fischer-Tropsch synthesis, and its purpose is to guide future experiment and thought.A general review of the literature on the Fischer-Tropsch synthesis will be published in the near future as a chapter by H. H. Storch for a book entitled, ""The Chemical Utilization of Coal,"" edited by H. H. Lowry. This chapter covers the literature up to l9). It is planned to bring the review up to date in a comprehensive bulletin on Synthetic Liquid Fuel Processes to be completed during the next year. ACKNOWLEDGEMENTSThe author discussed the significance of the data with several members of the Physical Chemistry and Hydrogenation Section.THE PREPARATION OF CARBIDES OF IRON, COBALT, AND NICKELThe reaction of carbon monoxide with Fischer-Tropsch metals was first studied in a quanitaive way by Bahr and his coworkers. The contents of their first papers, 3/ 4/ 5/ which deal with the action of carbon monoxide on nickel, cobalt, and iron, will be described in the following paragraphs, together with the pertinent results of other investigators."

Jul 1, 1944

By G. J. Simandl

"Since the 1980s, China has become the predominant producer of REEs. Recently, it introduced REE export quotas and this started a world-scale REE exploration rush. REE resources are concentrated in carbonatite-related deposits, peralkaline igneous rocks, pegmatites, REE ± P veins, ion adsorption clays, placers, and some deep ocean sediments. REEs could also be derived as a by-product of phosphate fertilizer, U processing, Ti-Zr-bearing placers, and exploitation of Olympic Dam-type sub-type of IOCG deposits. The ideal REE development target would be located in a politically stable jurisdiction such as Canada. REE grade and tonnage, mineralogy, and permissive metallurgy are some of the key technical factors that could be used to screen projects. INTRODUCTIONAccording to the International Union of Pure and Applied Chemistry (IUPAC), the term “rare earth elements” (REEs) encompasses yttrium (Y), scandium (Sc), and the lanthanide series: lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pm), samarium (Sm), europium (Eu), gadolinium (Gd), terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), and lutetium (Lu). This definition is used throughout this paper.REEs are subdivided into light (LREE) and heavy (HREE) categories. LREEs include, Sc, La, Ce, Pr, Nd, Sm, Eu, and Gd and HREE include Tb, Dy, Ho, Er, Tm, Yb, Lu, and Y. Promethium (Pm) does not occur in nature. Concentrations of individual LREEs in the upper crust of the Earth are comparable to those of base metals. Even the least abundant REE (Lu) is about 200 times more abundant than gold.The production of REEs, reported in the form of oxides (REOs), for 2011 is estimated at 140 000 t (Figure 1a). Although high technology industries can substitute several REEs with other materials, these substitutes are typically more expensive or less effective than the REEs they replace. A number of countries, including the United States, consider several REEs essential for national security, their economy, and a general reduction in green house gas emissions. The forecasted demand for individual LREOs is much higher than that of HREOs (Figure 2). Dy, Eu, Tb, Nd, and Y are essential for the US economy and subject to predicted supply disruptions (U.S. Department of Energy, 2010)."

Jan 1, 2012

The work described herein is the opening phase of an extensive system of underground excavation undertaken under contract with a Malayan authority.The specifications called for the lining of all tunnels in earth or broken rock with circular segmented cast iron lining, similar to that of the London tubes, and it is the installation of these linings which it is proposed to discuss.Owing to the long deferred delivery quoted and the obvious need for speed of access to the internal installation, it was decided to defer driving the completed circular section and substitute two small timbered headings.These could later be opened out in turn to full section and lined without prejudice to traffic, since both of them had access to the internal workings.NATURE OF ROCKThe rock series through which the circular sections were driven consisted of:(a) A wide zone of intrusive porphyritic granite, consisting generally of orthoclase phenocrysts in a ground mass of micro pegmatite. This area showed advanced weathering, varying from a stage showing slightly tinted kaolin containing approximately 20% of small boulders to one of ultimate decomposition to pure kaolin;(b) A narrow zone of weathered augite diorite, consisting of rock masses of a maximum weight of some 100-150 tons, isolated by clay seams up to 1 ft. 6 in. in width.The whole area was in a state of quasi-hydrostatic equilibrium, which resulted in heavy pressure immediately after excavation. Freshly broken faces would appear to be quite solid but, within a few minutes, would commence to sweat and "slab off" under pressure and, unless support was placed promptly, the whole face would burst out and run from above. Mucking was slow, owing to the plastic nature of the clay and the ease with which it puddled into slurry.In zone (b) a good deal of trouble was experienced because of the fact that the somewhat heavy blasting necessary tended to cause movement of the large rock masses. Subsequent scouring out of the supporting clay bands by the waterflow permitted settlement of the ground on to the timbers and many reinforcing sets were therefore required.The timbering of the pilot headings and its relation to the cross-section of the circular tunnels is shown in Fig. 1. Top and side spiling was driven in the ordinary way, but in bad ground intermediate sets and breast boards had to be placed. These sets were usually withdrawn after the...

Jan 1, 1941

By Clermont Lavoie, Marc Filion, Marcel Vallée

"Les mineralisation d'or des gîtes de la SOQUEM - Silver Stack dans is canton Bousquet se situent dans une bands de roches pyroclastiques asides du groupe de Blake River, d'âge archéen, dans le même horizon géologique que lee gites aurifères de Thompson Bousquet et Dumagarni situés plus a rest. La propriété a été explores anterieurement a maintes reprises depuis les années 1930, parfois jusqu'aux travaux souterrains, notamment par les groupes Mooshla, Warrenmac et Westwood Cadillac ainsi que par Silver Stack Mines.Ces zones auriferes se situent a l'intérieur de larges halos (jusqu'à 1,000 m x 400 in) de pyrite disséminée (2-5%) dans des tufs a lapilli et des agglomerate acides montrant des concentrations locales de pyrite. La zone 1, découverte en vérifiant par sondage une anomalie E.M., coincide avec une de ces concentrations de pyrite et la teneur en or est ici proportionnelle a la pyrite. Ce secteur se distingue par l'intensité de l'altération en séricite. La zone 2, qui s'étend sur près de 600 m, se situe dans un agglomérat acids, avec une faible teneur en pyrite, et montre de fines veinules de quartz-carbonate.Du point de vue géophysique, aucune methods ne donne des résultats probants: la polarisation provoquée montre de tree grandee anomalies correspondant aux halos de pyrite, tandis que lee concentrations de pyrite détectées par les méthodes E.M. (VLF ou EMH) sont loin d'être toutes aurifères. Les relevés magnétiques aident a établir la structure la où un certain contraste de susceptibilité magnétique est present. Les essais minéralurgiques préliminaires indiquent que la concentration de Bette mineralisation aurifère ne présentera pas de problems majeur."

Jan 1, 1977

By Harold M. Smith

Among the more important raw materials now utilized for the commercial production of synthetic organic chemicals is natural 'gas. Natural gas has been used as a fuel and source of energy almost from its discovery, but its potentialities as a chemical raw material were not realized until recently. Research in the use of natural gas for Chemical synthesis received great impetus from the discovery by Brooks and Humphrey4/ in 1918 of alcohols in the diluted ?acid oil? obtained by sulfuric acid treatment of cracked petroleum distillates. Experimental data soon showed that hydrocarbons from natural gas could be converted to these same products. Laboratory methods for chlorination of natural-gas hydrocarbons, particularly of methane for the production of methyl chloride, methylene chloride, carbon tetrachloride, and chleroform were known before that time but were not developed commercially. Methods for obtaining alcohol by oxidation of hydrocarbons derived from natural gas also were known before 1918 but had not received commercial consideration. Since 1918, and particularly during the past 15 years, the work of chemists and chemical manufacturers throughout the world has resulted in an accumulation of data regarding the reactivity of natural-gas hydrocarbons, and related hydrocarbons found in refinery gases or made synthetically. These data have been used to develop methods for converting hydrocarbons into chemical products and thus form the basis for a large and growing industry.

Jan 1, 1947

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By Evan Just

?We are certain there is need for research in every phase of mining." This statement by R. M. Crump of the Jones and Laughlin Steel Company (047) paraphrases opinion widespread among mining people. It is undoubtedly true. In preparation for this presentation, 193 organizations were asked to describe their mining research efforts. 60% responded, The meaning of "research" was taken in several different ways. The continual efforts of progressive companies to improve themselves were reported as research. We will call this and any effort to solve specific and immediate problems "practical research". The continuing investigation of subjects of long range interest will be called "basic research".

Jan 1, 1961

By SANDEEP KUMAR JENA

This paper reviews the recovery of potassium from different rocks and mineral sources. Global demand for potassium is rising steadily due to the growth of agricultural production. Fertilizer manufacture consumes the majority of the world’s potassium production, with other uses including those in the pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash (K2O) minerals, such as sylvite, kainite and carnalite, in countries like Canada, the United States, Israel and Russia makes them major potash producers, whereas agriculture-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia, Malaysia and India meet their potassium requirements through imports only. In these countries, the huge availability of potassium-bearing rocks/minerals like nepheline syenite, feldspar, mica and glauconitic sandstone, containing around 4 to 17 percent K2O, brings up the prospect of commercial production of potassium. Potassium recovery from minerals/rocks is complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast-leaching have been discussed for the successful recovery of potash values from these rocks/minerals. Although seawater is vastly available, the recovery of potassium from seawater using chemical precipitation, solvent extraction, membrane separation and ion-exchange methods is not cost-effective due to low concentration of potassium.

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By S Harris, A Bossilkov

The Kwinana (Western Australia) and Gladstone (Queensland) industrial areas are among the few dozens of heavy industrial areas globally that demonstrate significant levels of regional resource synergies. Such synergies are also referred to as æindustrial ecologyÆ or æindustrial symbiosisÆ. Fundamentally they involve the exchange of by-products or sharing of utilities between companies in close geographic proximity to achieve competitive advantage and environmental benefit. A concerted research effort is currently underway to foster greater realisation of regional resource synergies in minerals processing intensive regions, in Australia and internationally. This paper summarises current insights from the foundation research into engineering tools and technologies and enabling mechanisms for regional resource synergy developments. Regional resource synergy developments were reviewed for 16 international and two Australian regions. It was found that Kwinana and Gladstone compare favourably with the well-regarded international examples of regional synergy development. Given the fairly strong evidence that self-organisation is critical for regional synergy developments, an implementation model has been proposed that captures entry points for synergy developments at the level of platform (industry collaboration), process (developing synergy opportunities) and project (assessing and implementing specific synergies). It was also found that regional synergies have so far developed in the absence of specific methods for identification and screening of synergy opportunities. Moreover, very limited attention has been paid to the associated technological and engineering challenges. The current technical research effort therefore targets: the development of a toolset for the identification and development of potential synergy opportunities; and assessment of technology needs and opportunities for regional synergies involving water, energy and materials recovery and reuse.

Jan 1, 2006

By Arthur Crowfoot

This paper describing t o concentrating practice of the Phelps Dodge Corporation, Morenci Branch, at Morenci, Ariz., is one of a series of articles on concentrating methods and posts being prepared by the Bureau of Mines. The Morenci concentrator, locally known as No. 6 concentrator, treats 5,000 dry tons of ore per 24-hour day by primary tabling followed by two stages of flotation treatment, at 48-mesh size and 65-mush size respectively.

Jan 1, 1931

By Frederic P. Dewey

THE Bureau of the Mint of the United States Treasury maintains 13 offices for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, eight tables of comparative results, taken from the regular work of the service, are given. These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement. in the assay-results, and follow through decreasing gold fineness and . increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the' agreement of the assay-results; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these are added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion2 I

Aug 1, 1909