Search Documents

By S. M. Spottiswoode

Much as one hopes to predict whether damaging seismicity might occur somewhere in the next shift, this is not possible at present. Recently, an analysis of seismicity at two mines has shown that a small increase in seismicity occasionally occurs before both large and small events. This analysis is extended here to five mines, with the same results. Earthquake seismologists forecast hazard in terms of the average incidence of earthquakes over the last 50 years, adjusted on an hourly basis according to the possibility of aftershocks of events that have happened. The rate of seismicity in any area remains approximately constant when expressed as seismicity per area mined, or better still, per unit of elastic strain energy released. It is suggested that seismic hazard in mines be estimated using historical seismicity and forward modelling, adjusted according to the possibility of aftershocks. In summary, medium-term forecasting of seismicity is viable; short-term prediction of large events is not.

Jan 1, 2010

By M J. Kongas, K M. Saloheimo

This paper presents the art of on-stream particle size and elemental analysis used at iron ore concentrators, followed by the results and experiences from several sites.Online particle size analysis is rather common at medium- to large-sized concentrators. Online X-ray fluorescence (XRF) elemental analysis, however, is only used in some iron ore concentrators, while it is a routine practice in base metal concentrator plants. Online XRF analysis is applicable for process monitoring and control down to four to five per cent silica by measuring Fe assays accurately. With lower silica content, direct measurement of silica and other light elements is required. Some light element analysers that are based on the prompt gamma neutron activation analysis (PGNAA) method have been developed, but they have not performed up to expectations with slurry analysis. Other methods have been tried though these have not been used beyond prototype installations. Operating online light element slurry analyser installations are not common in iron ore applications.There is an economic incentive to mine lower and variable grade iron ore resources, which require concentration and removal of several impurities to produce high-quality concentrates for pellet production. Monitoring such operations by on-stream analysis has significant economic benefits, and there is a need to develop a dependable slurry online analyser for Si, Al, Mg and other light elements. The latest developments in slurry on-stream light element analysis are described.CITATION:Kongas, M J and Saloheimo, K M, 2013. Online slurry analysis for process control and monitoring at iron ore concentrators, in Proceedings Iron Ore 2013 , pp 303-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Mark I. Copeland

This study was conducted by the Bureau of Mines to determine the effect of steel reheating practices in burning natural gas on the amount of silicon required to prevent the formation of copper on steels containing up to 1 wt-pct Cu. Formation of copper, which causes surface hot shortness, was readily prevented by as little as 0.3 wt-pct Si and by 2 vol-pct excess oxygen in the furnace atmosphere when reheating steels containing up to 0.8 wt-pct Cu. Up to 0.8 wt-pct Si content and careful control of reheating conditions were necessary for steels containing 1 wt-pct Cu. Best conditions for these steels were reheating to 2,200° F (1,205° C) in burning gases containing 2 vol-pct excess oxygen, and then to higher temperatures in gases of 6 vol-pct excess oxygen. Slag and mold wash were not detrimental on steels reheated for 8 hr by a soaking-pit-type furnace schedule, but they were problematical on steels heated for 2 hr by a pusher-type furnace schedule. The effect of silicon contents on scaling rates also was determined.

Jan 1, 1974

By Abdurrahman Cetinbas

The effect of water infusion on the flow of methane and on the production of dust was investigated at an active face in the Pittsburgh coalbed. The average total flow of methane at the face decreased by approximately 79 percent, whereas the flow from the ribs increased about 24 percent after infusion. On the day after infusion, dust concentrations appear to have been reduced; however, the presence of large quantities of rock dust obscured the results on the following days.

Jan 1, 1972

The stability of parallel underground coal mine galleries and pillars have been investigated using two- and three-dimensional (3D) numerical stress analysis. Anisotropic horizontal in situ stresses and the direction of the excavations have been considered in the numerical analysis. The stability of the tunnels driven in a coal seam at various working depths has been investigated taking into account different strata conditions and then results from two- and three-dimensional numerical modelling studies were compared. Maximum principal stress components have been chosen in three various directions: vertical, parallel and perpendicular to the tunnel axis. Analysis have shown that in the anisotropic in situ stress field, the favourable direction of underground mine openings which have different strata conditions depend not only on the horizontal in situ stresses but also on the vertical in situ stresses. Furthermore, 3D numerical modelling studies have been carried out to investigate stability of multiple entry longwall panel gate roads and pillars with various width-to-length ratios (W/L). Results of the modelling studies have shown that the critical dimension of coal pillars depends on their width and the direction of maximum horizontal stresses.

Dec 6, 2010

bauma 2004 will feature a couple of firsts for one of the world’s largest construction and building materials machinery exhibitions. The event is scheduled for March 29 through April 4 of next year at the New Munich Trade Fair Center in Munich, Germany. For the first time, bauma will feature an exhibition area dedicated to mining equipment and technology. Also for the first time, the Commonwealth of Independent States (CIS) will be a partner region of bauma.

Jan 1, 2003

By S. T. Camagu, J. Dutta Majumdar, S. L. Pityana

Laser surface alloying was used to develop copper and molybdenum aluminides by injecting premixed copper and molybdenum powder particles into a laser-generated melt pool on an aluminium substrate. Different laser processing parameters were used to produce the composite thin layers on the substrate material. The microstructure and phase constituents of the composite layer were studied by means of scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD) techniques. Experimental results show that the matrix structure of the metal matrix composite layer consists of ?-CuAl2and MoAl5. Surface hardness was increased by a factor of 3.

Jan 1, 2015

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By Kevin Andrews, Terry Hamric, Scott Nelson

"Mining conditions in underground coal mines are dictated by the environment in which the coal seams were geologically deposited. Depositional features can change rapidly, significantly affecting mining conditions. Mine geologists understand factors affecting mining conditions, predict future conditions, and provide guidance to mine management. A case study demonstrates how a mine in Appalachia merged an understanding of depositional environments with mining conditions and drilling data to make informed decisions as the mine encountered geologic anomalies. The assessment included drilling, mapping of geologic hazards and mine productivity, and creation of a conceptual depositional model. Metallurgical coal quality and clean tons per foot served as incentives for continued advance. Mining in the south was historically favorable, with good production and advance rates. As mining advanced north, changing geologic conditions caused the upper seam split to abruptly disappear. The mine ramped down into the lower seam split. Mining in the north area encountered unfavorable conditions, including transition roof, “horsebacks,” sandstone intrusions, roof rolls, and bony floor, resulting in low rates of mining advance. The mine geologist characterized the features and created a predictive model for future mining. Most of the adverse conditions were attributed to the coal in the north being part of an incised, transgressive valley fill environment, as compared to the favorable conditions in the south resulting from a floodplain depositional environment. Geologic conditions, low productivity, and unfavorable future predicted conditions in the north ultimately resulted in mine closure and reallocation of resources to a new mine with better forecasted conditions.INTRODUCTIONThe role of a geologist in assisting coal mining operations to understand and predict the impact of varying geological factors on mining productivity is a critical one, especially when management decisions must be made about the future prospects of a mine operating in difficult conditions. Chase, Newman, and Rusnak (2006) provide a very thorough discussion of the evolution of the role of the coal mine geologist and emphasizes the importance of understanding geology with regard to mine management decisions. Using actual mining performance data to determine which geologic factors are the most critical for mining is a powerful tool for making informed mine management decisions. For example, Nelson, Mullennex, and Miller (1988) provide a case study of analyzing the geologic factors impacting productivity of a Kentucky longwall mine to predict future mining conditions for the operation. In that case, the difficult geologic factors for longwall mining were prevalent across much of the remaining permit area and, in response, mine management converted the operation from a longwall operation to a continuous miner (CM) operation to better adapt to the geology. In another example, Keim and Miller (1999) evaluated geologic conditions impacting a West Virginia longwall mine. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed. Numerous examples of advanced Geologic Hazard Mapping (GHM) methodologies have come from government agencies and academia. For example, development of the Coal Mine Roof Rating (CMRR) system (Molinda and Mark, 1994) provided a standard means for geologists and engineers to communicate quantitatively with regard to mine roof conditions, and the introduction of the Stability Mapping System (SMS) provided an efficient means for analyzing numerous factors affecting coal mine stability (Wang and Heasley, 2005)."

Jan 1, 2019

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

By Christopher J. Bise

INTRODUCTION The level of analysis for the selection of extraction practices and equipment for surface mining differs significantly from that found in underground mining. In underground mines, manufacturers establish the operating ranges of the equipment, such as continuous miners, loaders, and boring machines, based upon required clearances. Even in conventional mining, the drilling and blasting operation is usually based upon experience. The selection of extraction methods and equipment for surface mining is more complex. Since the equipment is not as confined as in deep mining, and the topography tends to be highly variable over the limits of the mining property, primary extraction equipment must be sized according to reach and capacity. Further, due to the depositional characteristics of the over- burden, drilling and blasting patterns must be well- designed to provide proper fragmentation. The following sections provide a general outline for the selection of surface excavation practices and equipment. The topics covered include drilling and blasting and the selection of both primary extraction equipment (draglines and stripping shovels) and secondary extraction equipment (bulldozers, scrapers, and front-end loaders). EXCAVATION FUNDAMENTALS Before discussing surface excavation, a few concepts need to be defined. A bank cubic yard of material is equal to one cubic yard as it lies in its natural or undisturbed state. A loose cubic yard is that portion of a bank yard that after being disturbed has expanded to measure one cubic yard. Swell is the volume increase of a material when it is removed from the natural state. Finally, load factor is the percentage decrease in the density of a material from its natural state to a loose state. Table 1 summarizes these concepts for various materials. When the amount of overburden to be removed to meet a predetermined production rate is established, a suitable bucket size for the primary stripping equipment must be calculated. The following equation can be used: NBSIZE = TBC/[(OF) (BF)] (1) where NBSIZE is the actual bucket capacity after considering the swell percentage, the bucket fill factor, and the operating efficiency; TBC is the theoretical bucket capacity (TBC = COB/NTCPM); OF is the operating efficiency; BF is the bucket fill factor; COB is the cubic yards of overburden to be removed; NTCPM is the number of theoretical cycles per month [NTCPM = (SMH) (3600)/(CT)]; SMH is the scheduled monthly hours; and CT is the cycle time in seconds. FRAGMENTATION PROCEDURES Drilling Where the strength of overburden material is such that blasting is required prior to excavation, drilling is conducted before using explosives. Two methods of drilling are found in mining-percussion and rotary. Penetration of overburden by percussion drilling is carried out by successive impacts of the bit into the rock. Emphasis in this section will be placed on rotary drilling, because for surface mining it is the most versatile form of overburden penetration. Rotary drilling is conducted by rotating a rigid string of tubular rods to which a rock-cutting bit is attached. The drilling energy is supplied by rotation as well as thrust and the cutting action consists of abrasion, scraping, spalling, or chipping. The size range for rotary-drilled blastholes is from 4 in. to 15 in., with 9 in. and 12 in. being common sizes. There are two types of bits used for rotary drilling-drag and rolling cutter. Drag bits are applicable in soft to medium-soft shales or their equivalents. Since their effectiveness is dependent upon a successful scraping action, drilling thrust is lower for drag bits than for rolling cutter bits; the opposite is true for torque requirements. The bits are usually fitted with replace- able tungsten-carbide cutters. Rolling cutter bits, though available in a two-cone configuration, are usually of the three-cone style (Table 2). The rolling cones have either large steel teeth for drilling through soft formations or small tungsten-car- bide inserts for drilling through hard formations. Table 3 relates bit size and weight to the strength of the rock. The major advantage of rotary drilling is its rapid drilling rate. This is due to the fact that, unlike percussion drilling, rock penetration is uniform with depth. Blasting Effective bank preparation deals not only with the fragmentation of overburden but also with the mini-

Jan 1, 1986

By Bruno Gemmi

The objective of the ? 200 million ($280 million) project Parma Railways Station-Urban Transformation was the reconnection of the North and South parts of the town by constructing an 80 m (250 ft) wide sunken artery passing under the four double railway tracks of the station without any impact on train traffic. The site of the project, adjacent to the Parma River, presented water seepage problems at any excavation depth. The use of conventional large diameter bored pile machinery was not allowed by the Railway Authority because equipment dimension and construction phases do not comply with train traffic safety regulations. Foundations for the bypass were thus constructed by minipiles nested into jet-grouted soil using machinery operating within the existing head room and at a safe distance from the tracks. Jet-grouting treatment reached depths of 25 to 28 m (80 to 90 ft) from tracks? grade and embedded minipile-heads were terminated at 2 to 3 m (6.6 to 10 ft) below grade. Load tests on minipiles were pushed to failure. Failure occurred at a 240 t (265 t) load without breakage of the bond between the jet grouted soil and the minipiles. A 0.93 MPa (135 psi) shear resistance ??? between minipile steel casing and the jet grouted soil was measured prior to the failure of the steel casings. Overall measured foundation settlements were well within expected values and were considered insignificant.

Jan 1, 2011

By Eleanor Abshire

THIS PUBLICATION is the third to be prepared as a result of a cooperative project by the Bureau of Ships and the Bureau of Mines for accumulating literature published on zirconium and hafnium. The undertaking also resulted in the establishment of an information center on zirconium and hafnium at the Bureau of Mines station at Albany, Oreg., for the use of research organizations and others. The present bibliography consists of references (with abstracts) to pertinent literature on zirconium. The first publication in this series was Information Circular 7771, Bibliography of Zirconium, published in April 1957. It consists of 969 abstracted reports and 645 U.S. and foreign patents. The second publication, called a supplement to Information Circular 7771, is numbered Information Circular 7830 and consists of 844 abstracted reports and 62 U.S. and foreign patents. It was published in October 1958.

Jan 1, 1962

By Val E. Payne

Issues between resource utilization and resource preservation often develop in connection with coal mining. One such conflict exists in eastern Utah where PacifiCorp and Energy West Mining Company are working with State and Federal agencies to address the resource recovery/resource preservation dispute. The effects of underground longwall coal mining on golden eagle (Aquila chrysaetos) cliff nesting sites have been studied at the Cottonwood Mine since 1986. Subsidence, escarpment spalling, and the nesting activities of the local eagle population were monitored.

Jan 1, 1986

By D Craw, D Falconer

The Morning Star mine is one of numerous historically mined gold-quartz lodes in the Preservation Inlet goldfield of southwest Fiordland. The mine is hosted in Early Ordovician metasedimentary rocks that are composed predominantly of psammitic and pelitic lithologies. These rocks still contain their primary depositional features and are characterised by upper greenschist facies metamorphic grade.   The Morning Star mine lies on the eastern limb of a gently south plunging anticline. A bedding parallel fault-vein and an associated network of minor quartz veins hosts mineralisation. The main fault-vein structure strikes N-NW, dips steeply (~60¦) W, has a strike length of ~350 m, a vertical extent of ~170 m and is up to 2 m in thickness. The internal structure of the fault-vein consists of laminated quartz, massive and fibrous quartz, and silicified breccias/cataclasites. Gold is typically coarse grained (~1 - 2 mm) and associated with pyrite, arsenopyrite, chalcopyrite, tetrahedrite and galena. The geometry of the Morning Star mine is similar in form to that of a saddle reef. Gold-quartz lodes in the Preservation Inlet goldfield are comparable in geometry and host rock to their offset equivalents in the Golden Blocks field of NW Nelson.

Jan 1, 2005

By A. B. Parsons

Jan 1, 1971

By Harry: Lobb Verakis

Mining operations have made tremendous strides in improving the safety of blasting as shown by the significant and continual decrease in fatalities and serious injuries. Advances in blasting technology and blasting practices have played a significant role in reducing fatalities and injuries. However, even with the decline of fatalities and injuries blast area security continues to be by far the leading factor in blasting accidents. Even though there continues to be an increase in the use of industrial explosives and blasting agents in the U.S.A., the decline in fatalities and injuries from blasting accidents has persisted.

Jan 1, 2010

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By Christopher J. Bise

INTRODUCTION Perhaps no other area reflects the art as well as the science of mining-engineering design quite as obviously as strata control. This is due to the fact that the design of mining structures is difficult because rock rarely behaves as a homogeneous medium. Further, the original state of stress and the mechanical proper- ties of the in situ rock are somewhat difficult to deter- mine. However, those aspects that are hard to treat mathematically can and have been successfully approached by model studies and in situ measurements. This chapter will review the fundamentals of strata- control design and will provide examples of applications to typical problems. STRESSES AROUND MINE OPENINGS A close examination of Fig. 1 reveals that, prior to mining, stresses exerted in the overburden can be in both the horizontal and vertical directions. In the example problems of Chapter 1, it was shown that the maximum compressive stress (uv) at any depth (D) below the surface can be approximated as follows: [ ] Further, the lateral stress (oh) is related to the maxi- mum compressive stress by utilizing Poisson's ratio (µ): [ ] As soon as a heading is driven, such as the one in the coal seam shown in Fig. 2, the stresses shift to the sides, or abutments, of the opening. Clearly, these compressive stresses around the opening exceed the pre-mining conditions. The problem of designing an underground opening, therefore, is to determine the maximum stresses and to note if they exceed the ultimate strength of the rock. Table 1 lists several rocks with their corresponding strengths. Figs. 3 to 5 depict the boundary stress concentrations around circular, ovaloidal, and rectangular openings. M is the ratio of the horizontal stress to the vertical stress, or as defined above, p/(l-p). This text will concentrate on the state of stress represented by M = 0.33, which corresponds to the condition of no lateral deformation in a rock having a Poisson's ratio of 0.25. For an ovaloid with an opening width-to-height ratio of 2.0 (Fig. 4), the boundary stress concentrations are at their maximum values at the comers of the opening, with values in excess of 3.0. If the depth of overburden is 500 ft, then the maximum boundary tangential stress ([ ] ) of the ovaloid is: [ ]

Jan 1, 1986