Search Documents

By F. D. DeVaney

Manganese-bearing deposits f the Leadville, Colo., district are of two distinct types. Manganosiderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 900 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 18.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By F. D. DeVaney

Manganese-bearing deposits of the Leadville, Colo. district are of two distinct types. Mangano siderite, a combined or intimately mixed ferrous and manganous carbonate, occurs in unaltered zones as the predominant mineral. From 50 feet below the surface to as deep as 800 feet, psilomelane and wad, both black manganese oxide minerals, are found in intimate contact with hematite and limonite. A typical analysis of the black oxide ore shows 20.08 percent Fe, 19.64 percent Mn, 15.91 percent insoluble, 14.91 percent moisture, 0.94 percent Zn, and 2.13 percent Pb. A considerable tonnage of the oxide ore has been mined for production of spiegeleisen and for other purposes.

Jan 1, 1940

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific- indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1971 at 5 million tons valued at $200 million, averaging $40.00 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, calcium carbonate, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface smoothness, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. The chart in Table 1, updated from the 3rd edition of Industrial Rocks and Minerals, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses.

Jan 1, 1975

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By Laurence F. Kelley

This paper is one of a series being prepared by the United States Bureau of Mines on shaft-sinking methods and costs at individual operations in various mining districts of the United States. The methods and costs described herein are those of The Consolidation Coal Co. at one of its operations in the Tug River district, McDowell County, W. Va. ACKNOWLEDGMENT The author is indebted to Frank R. Lyon, vice-president, Thos. G. Fear, general manager of operations, and Chas. Enzian, chief engineer, of The Consolidation Coal Co., for valuable assistance and collaboration in the preparation of this paper. W. A. Cole, manager of the E. J. Longyear Development Co. furnished valuable data on methods and performance averages.

Jan 1, 1932

By R. O. Burt, D. J. Ottley

"SYNOPSISRecent developments in the use of the Bartles-Mozley table and the Bartles CTS screen are described for the gravity preconcentration of fine heavy mineral and metal particles present in low grade pulps. The B-M table is a relatively new device used for the recovery of particles of up to 100 micron size down to 5 microns or in the case of gold and platinum, down to 1 micron. The CTS screen is a wet screening device used for feed preparation ahead of the Bartles-Mozley table and will size effectively down to about 300 mesh. Results and operating data for a number of different materials are given including outline flowsheets; the effects of the major variables on the performance of the table are briefly discussed. The potential of the B-M table to treat a variety of different ores, coal, tailings, and waste products are considered. The utilization of the B-M table in association with other unit processes to improve overall results as well as to improve the economics of design and performance of plants are also mentioned.INTRODUCTIONA number of new gravity concentration devices have been developed in recent years for the recovery of fine heavy mineral and metal particles but for reasons which include low capacity, high capital or operating costs, competition from other and better processes, the absence of simplicity or reliability in operation etc., only a few which include the Bartles-Mozley table, have been proved to be of commercial application.The name of the machine is derived from the inventors name, Richard Mozley, who developed the B-M table at the University of Bristol in England. The table was subsequently taken up and patented, world-wide, by the National Research Development Corporation a British government agency. An exclusive license to manufacture the table was granted by NRDC to Bartles (Carn Brea) Ltd. in Cornwall, England."

Jan 1, 1973

By G Ma, L Qi, J G. Shellnutt

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Emeishan large igneous province (ELIP) of SW China is host to magmatic Ni–Cu–(PGE) sulfide and Fe–Ti–V oxide deposits which contain economic to subeconomic concentrations of precious and base metals. The formation of a given deposit-type (ie sulfide versus oxide) is thought to be related to the type of parental magma (ie high-Ti versus low-Ti) and the subsequent processes (ie fractional crystallisation and sulfide segregation), which allowed for metal enrichment.We examined the PGE of Baima and Taihe oxide-bearing layered mafic intrusions from the ELIP (Shellnutt, Ma and Qi, in press), and compared them with the nearby Xinjie and Hongge intrusions as well as with the Emeishan flood basalts. The PGE results for the two intrusions are contrasting. The Baima gabbroic rocks are almost PGE-barren (SPGE < 4 ppb) whereas the Taihe gabbroic rocks are variable, but generally much higher in PGE concentrations (SPGE < 2 to ~300 ppb), although the gabbros from both intrusions are enriched in platinum-subgroup PGE (PPGE = Rh, Pt and Pd) relative to iridium-subgroup PGE (IPGE = Os, Ir and Ru). Cu/Zr, Ni/Ir, Y/Pt, Cu/Pd and Ni/Ir systematics suggest that the Baima rocks were derived from a relatively evolved, mafic, S-undersaturated parental magma that was affected by earlier sulfide segregation. In contrast, the Taihe rocks record evidence of both S-saturated and S-undersaturated conditions and that the parental magma was likely emplaced very close to S-saturation. Through comparison of the PGE contents in the Emeishan flood basalts and the Emeishan oxide-bearing intrusions, we provide a self-consistent model for ELIP that the PGE budget in a magma is not strictly controlled by magma series (high-Ti versus low-Ti), but very much by crustal contamination.CITATION:Ma, G, Shellnutt, J G and Qi, L, 2015. Platinum group elements in the Baima and Taihe Fe-Ti oxide-bearing gabbroic intrusions of emeishan large igneous province and problems on propensity of magma series for sulfide- versus oxide-dominated deposit types, in Proceedings PACRIM 2015 Congress, pp 303–310 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By J. R. Thoenen

[Before 1914 Germany held a virtual monopoly on the world supply of potash for fertilizer purposes. During the World War, potash shipments to the United States ceased, and recourse was had to domestic supplies. High war-tine prisms stimulated interest in various sources, and domestic production increased rapidly. At the close of the war, resumption of shipments from Germany mad other sources reduced prices to below pre-war levels, and, as a result, most of the domestic procedures ceased operations. This experience demonstrated that a domestic source of potash was necessary but that it must be of such a nature that it could compete in price with foreign sources. As a direct result the potash content of thick]

Jan 1, 1941

By Vincent A. Scovazzo

Many accepted and useful methods have been developed and used for pillar design. Each method has its own particular strengths and weaknesses. Three methods addressed in this paper are; empirical, analytical, and numerical. Each of these methods have their place in pillar design. Analytical methods result in close approximation of the ideal pillar (most economical, stable, or yielding) and are suitable for use in final mine design and in analyzing existing problems. BOYD uses the analytical method to develop site specific mine pillars design equations. An analytical method, one of many developed by BOYD, is presented here and is based on the procedure used by Wilson (1) and others in development of their empirical equations.

Jan 1, 1995

8186. Aquilina, C. Determinazioni relative di gravita eseguite nel 1939 (Relative Determinations of Gravity Made in 1939), Ric. Ingegn, Rome, vol. 10, 1942, pp, 6376. In 1939, the author made a survey of relative gravity in the Mediterranean-basin, 41° 35,5' to 41° 56.3' northern latitude and 0° 10,3' to 0° 28' longitude, referred to Mt. Mario. Ten stations were covered; 25 other stations had been occupied in the vicinity of Rome and in Albanian mountains during previous years. The new measurements revealed gravity anomalies ranging within the following limits: (1) With a free-air reduction, between + 29 and + 120 mgl., average + 60 mgl.; and (2) with a Bouguer reduction, between + 22 and + 87 mgl., average + 41.5 mgl. - V. S.

Jan 1, 1946

By R. L. Castro

Block caving methods, when operated under favourable rock mass conditions, can achieve higher production rates and lower operating costs than other various existing underground mining applications. For this reason, it has been considered the preferred method for the mining of deep and large orebodies in current and future operations around the world. One of the key aspects in the design of block caves is the selection of the production level layout, which, among other parameters, is based on the gravity flow characteristics of the caved rock. This is because gravity flow has a large impact on total ore recovery and the amount of dilution in a caving operation. Today, there are a number of computer based methods which aim to emulate the gravity flow pattern of the caved rock. In this paper, the authors present the development of FlowSiman improved model of gravity flow based on the cellular automaton approach, to estimate dilution entry, mixing and ore recovery. As part of the model development, flow simulations were conducted and subsequently compared to full-scale data collected at two mine sectors operated by Codelco Chile. The results indicate that by using proper calibrated parameters, good correlations between simulated and measured grades as well as dilution entry are obtained. The potential use of the numerical tool to evaluate drawpoint spacing in terms of recovery and dilution for block/panel caving operations is also presented.

Jan 1, 2009

Jan 1, 1997

By C. J. Hall

Twenty eight pulse release sulfur hexafluoride tracer gas field tests were run in a multi-level multi-vein hard rock mine to measure leakage ventilation. The mine had numerous underground booster fans and gob filled old stoping areas and consequently numerous leakage paths. The tests proved that the equipment and methods developed by the USBM can be used successfully in complicated ventilation circuits. The leakage quantities varied each time a major change was made in the main ventilation circuit. Usually leakage quantities had to be remeasured after a main ventilation change, but measurements could be duplicated for anyone configuration except under certain defined circumstances. The characteristics of an individual leakage path could be determined from the difference between the measured sum of two paths and the calculated characteristics of one of the paths. Many leakage paths could not be evaluated accurately on one shift. Comments are made on equipment performance and field techniques. Programs for the calculation of gas concentrations and recirculation from measured data and for the mechanical integration necessary for a calculated leakage characteristic have been written for an HP 9810 and are included.

Jan 1, 1975

By Jan A. Nemcik

Steel mesh has been used successfully for many years to control friable roof conditions and prevent loose roof and rib material from caving into the roadway. Despite its extensive use, the installation of steel mesh is difficult to automate and many other products have been evaluated as an alternative for skin control. Ideally, the properties of these new products should be similar or better than those of the steel mesh. In particular, development of a strong and resistant shell that minimizes movement along the fractured rock and coal surfaces between the bolt anchors is recommended. A strong surface adhesion and the strength of a reinforced polymer skin can provide the necessary toughening mechanism required to enhance roadway surface support by forming a reinforced polymer/rock surface layer. Most of the Thin Spray-on Liners (TSL) evaluated in the mines are weak with slow curing times, and the plastic mesh currently used to support the coal ribs is relatively weak. Therefore, neither material can seriously compete with steel mesh. Currently, a new polymer product that cures in seconds and forms an instantaneous strata binder that surpasses the properties of steel mesh is under development at the University of Wollongong.

Jan 1, 2009

By William A. Stickney

The zirconium-hafnium separation plant at Albany, Oreg., was the result of a chain of events that started with studies by A. R. Kaufmann at the Massachusetts Institute of Technology. Variations in the listed neutron-absorption cross-section of zirconium caused him to suspect a misprint. As a result of these discrepancies and following his suggestions, Oak Ridge scientists made studies establishing a value of 0.4 barn or lower. This meant that the potential of zirconium for reactor application was greatly enhanced. Since hafnium is invariably associated with zirconium and has a high neutron cross-section, it was necessary that an efficient hafnium-separation method be developed before the superiority of zirconium as a structural material in nuclear reactors could be realized. The Albany plant was built and operated for the Atomic Energy Commission (AEC) under Letter Agreement AT-(11-1) -140, patterned after a plant operated by the Carbide and Carbon Chemicals Corp. at Oak Ridge, Tenn. Construction was begun in April 1951. Hafnium was to be extracted preferentially as hafnium thiocyanate from an aqueous mixture of zirconyl and hafnyl chlorides in hexone (methyl isobutyl ketone) by a liquid-liquid countercurrent system.

Jan 1, 1959

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By J. K. Borchardt

The use of statistical design to optimize deinking process design has been studied for the flotation deinking of newspapers. The interactions of two variables are often important in determining flotation deinking efficiency. The interactions can be synergistic or antagonistic. These interactions would not be discovered using the traditional method of varying one parameter and holding the other variables constant. An experiment design in which two or more process parameters are varied simultaneously is required to identify these interactions. A considerable number of conclusions could be drawn about the relative importance of process variables on ink particle size distribution, ink removal efficiency, and flotation yield loss in a flotation deinking process. However, these findings could be influenced by the deinking surfactant and the ink chemistry.

Jan 1, 2001

The Beginnings of Mineral Processing Research in Canada - A Short Account

Sep 13, 2010

Gold recovered on the strikes at the Central Norseman mill, Norseman, Western Australia, has an approximate assay fineness of 850. Bullion recovered from the cyanide plant at the mine is of much lower value, and occasionally its assay fineness has been as low as 250. This indicates either that the fine gold particles in the ore consist of an alloy richer in silver than the coarse particles or else that a silver mineral, as well as the gold, is dissolved by the cyanide solutions.It had been observed at the mine that the amount of silver in the bullion appeared to increase when galena appeared to be more abundant in the stoped ore. Interest was, therefore, attached to the possible occurrence of a silver mineral associated with galena and, at the same time, soluble in cyanide.Four specimens of ore from different horizons in the mine were collected by the mine staff for examination as to whether any marked difference in the fineness of gold was apparent on a polished surface and for determination of the silver minerals. As the Norseman ore-body is a quartz reef containing a very small percentage of sulphide, the specimens were selected either because they cont;:lined free gold or because they were, relatively rich in sulphides. They were obtained from the following localities at the Phoenix shaft.1. Level 16, section 28.2. Level 16, section 31.3. Level 8, section 31.4. Level 14, section 38.Specimens Nos. 1 and 2 were thus obtained from different positions at the same mining horizon, while specimens Nos 2 and 3 were obtained from different levels in the same vertical section of the mine.All the specimens consist of quartz characterized by thin, discontinuous seams of sericite and the presence of a little ankerite. Gold and sulphides tend to be localized along these seams, but particles of gold and sulphides are also scattered throughout areas of white quartz. This scattered distribution of the sulphides in relatively wide areas of quartz has involved the preparation of two or more polished sections from each specimen.The outcome of the microscopical examination of these specimens has been to determine that there is no appreciable variation in the colour of the polished particles of gold and, therefore, no marked difference in the amount of silver alloyed with the coarse and fine particles. The presence of small quantities of the tellurides sylvanite, hessite and altaite has been revealed, and found to vary in abundance with the abundance of galena.

Jan 1, 1944

IN all wet concentration processes it is of primary importance to determine to what degree the crushing must be carried in order to obtain the maximum profit per ton of ore milled.To effect a clean separation, either by gravity or flotation treatment, between either one valuable sulphide from another, or a sUlphide from the gangue, the ore must have been subjected to grinding to such an extent that the particles to be separated are completely liberated from each other.Insufficient crushing will result in either an incomplete separation of the sulphides from each other, and thus a loss of the one sulphide in the other, or else a loss of the valuable sulphide in the gangue.This being so, the question arises whether the added cost of extra crushing would be economically warranted by the increased recovery consequent on such a step.

Jan 1, 1927