Search Documents

A study of the accessory opaque iron-titanium oxide minerals of the Oiles Complex, central Australia, was an Important complement to an investigation of the magnetic properties of the Complex. These minerals constitute no more than 10 per cent of the rocks sampled, and generally less than 1 per cent of the ultramafic rocks ("magnetite" concentrations were not sampled for magnetic investigation).Titanomagnetite is the main opaque mineral present, although ilmenite exsolution has been widely developed. High-temperature oxidation of these produced mainly titanohematite, pseudobrookite and rutile. Both exsolution and high-temperature oxidation developed along specific crystallographic directions (along {111}), and in Irregular patches. Low-temperature oxidation is generally not well-developed, indicating the small degree of weathering in the rocks sampled.Although the Oiles Complex is layered, no apparent overall preferred orientation of the iron-titanium oxide minerals was observed, other than crystallographically controlled alignment of very fine grains within pyroxene crystals. Other textural features of the opaque oxides are restricted to symplectic intergrowths mainly with the ferromagnesian silicates.

Jan 1, 1971

By S. L. Chen

Keywords: copper, concentrate drying, steam dryer, dryers By placing additional demands on energy and gas flow, the moisture content of a copper concentrate has an adverse effect on the smelting process. Different drying technologies, such as directly heated rotary dryers, flash dryers, and steam dryers, are available to solve this problem. The energy requirements of and off-gas generated from different dryer types are compared. The performance of the steam dryer was found to be superior to that of the others. In particular, the rotary steam dryer and its benefits are discussed. Structural properties confer an advantage on the rotary steam dryer, for wear on tube elements is eliminated, and drying efficiency is improved. If steam is available, the rotary steam dryer is an excellent choice for drying copper concentrates.

Jan 1, 2006

By Mi, Dong Liang, Jingyuan Bai, Victor Zhou, Xujun

Squirrel cage induction motors are the mostly used motors at present. Currently, the rotors of the squirrel cage induction motors are produced by aluminum die casting technique with the advantages of low cost of rotors. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size. Considering the huge quantity of motors, the die casting process is the best solution to produce copper rotor with economic cost. Because of the characteristics of copper, it is difficult to produce copper rotors by casting similar to that done in aluminum rotors. In order to improve the die casting quality of copper rotor, a new tooling structure was developed and the casting process of copper rotor was simulated and analyzed by Any-casting software. The filling process, solidification process, inner gas distribution and residual melt modulus were analyzed. It was found that the design of symmetrical runner and inner runner on both sides was helpful to reduce the impact of molten copper to the cavity surface during the filling process. The use of Slag traps array can reduce die casting defects inside the end rings. That will be helpful to improve the rotor quality. INTRODUCTION Squirrel-cage AC induction motors are most widely used in the world. In 2017, the total installed capacity of AC motors in China has reached more than 1.2 billion kW, and the annual power consumption accounts for about 60% of the total national electricity consumption. To improve the efficiency of squirrel-cage motor will be helpful to energy conservation and environment protection. There are several ways to improve efficiency of induction motors, using copper rotor is one of the most effective solutions. It is well known that the copper’s electrical conductivity is around 40% higher than that of aluminum. If copper is used to replace the current widely used aluminum in rotors, the total loss of motors will be reduced, hence increasing the overall motor efficiency. Copper rotors can be used to produce high efficiency and even super premium efficiency motors without enlarge the motor frame size.

Jan 1, 2019

Blasts should be designed so as to maximise the percentage of charges which shoot to a free face (Le, to a pronounced rock/air interface).Free faces should be rough, parallel and reasonably near to blastholes and, very importantly, concavely·biplanar relative to the charges (see Fig. 6b). The presence of biplanar free faces requires that each charge fragments and detaches its quota of the burden rock before the detonation of:1. later-firing adjacent charges in single-row blasts, and2. dependent charges in multi-row blasts.In multi-row blasts, biplanar faces are best achieved:1. by drilling blastholes on equilateral triangular grids,2. by selecting a VI, V2 or V3 initiation sequence, and3. by using down-the-hole delays.Biplanar faces start to be created only when the conventional value of effective blasthole spacing/effective burden distance (Se/Be) increases beyond about 2.4. Values of Se/Be less than about 2.4 result in planar free faces. Where biplanar faces are created, conventional values of Se/Be are invalid and appreciably greater than real values of Se/Be.

Jan 1, 1986

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By J. D. Morgan

Introduction In 1986, the US economy passed the $4 trillion mark. However, the value of domestically processed materials of mineral origin fell slightly to $240 billion. The value of metals produced from US ores was unchanged at $5.6 billion, as was recycled scrap at $4 billion, while the value of industrial minerals rose slightly to $17.9 billion. Consumer demand strongly affects mining and the US economy is relatively saturated with longlived products. Moreover, in recent years there has been a steady increase in consumer, mortgage, and federal debt, inhibiting new purchases of goods. Motor vehicles and housing are major traditional markets for mineral materials. However, the 242 million US citizens already possess 170 million licensed motor vehicles and 92 million dwelling units. In 1986, domestic motor vehicle production fell 3%, to 11.3 million units, while new housing starts rose slightly to 1.8 million units. Nearly all mineral commodities move relatively freely in world trade. As detailed in Figs. 1 and 2, in the last three decades world production of major mineral materials has greatly increased. At present, substantial excess productive capacity exists not only in the US but also in many other countries. Consequently, the US mineral industry is encountering increasing competition from other sources, along with increasing competition from newer, engineered materials. For example, US production of plas¬tics has risen from 900 kt (1 million st) in 1950 to 22.7 Mt (25 million st) in 1986 - on a volume basis significantly greater than steel. Plastics, too, are mineral-based materials, some 7% of petrochemicals going to their manufacture. 1986 saw increased calls for protection. But President Reagan, in his 1987 State of the Union Message and Economic Report to the Congress, reaffirmed adherence to a policy of free and fair trade. However, he stressed the need for increased efforts to open foreign markets to US exports and to increase competitiveness of US industry US imports of mineral-based minerals in 1986 were valued at $40 billion and exports at $24 billion. Strategic minerals As detailed in Fig. 3, imports supplied a significant proportion of total US consumption of several important materials, including many classified as "strategic and critical." There were no changes in stockpile policy during the year. Congress debated the President's 1985 proposals to reduce stocks of World War II-type materials and to focus more on high technology materials needed for the cutting edge of future military material. But no final action resulted. However, Congressional concern about apartheid in South Africa did result in increasing pressure to limit imports of South African minerals. Meanwhile, the National Critical Materials Council in the Executive Office of the President intensified its efforts to be better able to advise the President. The Defense Production Act provides authority for priorities and allocations, supply expansions, voluntary agreements, and

Jan 5, 1987

A diverse selection of rockbolt designs and resin anchors are available for use in underground mines. Research in recent years at the UNSW Mining Research Centre led to the construction of a rockbolt pull-testing facility. This facility has subsequently been upgraded, commissioned and initial test work has been completed to verify the pull-test process. A test program has been completed with the objective to understand the load transfer mechanism and improve the general performance of rockbolts. This paper describes the results of this research. Une sélection diverse de dessins du rockbolt et ancres de la résine est disponible pour usage dans les mines de métro. Faites des recherches ces dernières années à l'UNSW que le Centre de la Recherche Minier a mené à la construction d'une facilité de l'essai de la traction du rockbolt. Cette facilité a été améliorée par la suite, le travail de l'épreuve en commission et initial a été complété pour vérifier le processus de la traction-épreuve. Un programme de l'épreuve a été complété avec l'objectif comprendre le mécanisme du transfert de la charge et améliorer la performance générale de rockbolts. Ce papier décrit les résultats de cette recherche. Eine verschiedenartige Auswahl an rockbolt-Designs und Harzankern ist dafür verfügbar, benutzen Sie in unterirdischen Bergwerken. Forschung in letzten Jahren beim UNSW-Bergbau Forschung Zentrum führte Ruckerprobung-Einrichtung zur Konstruktion eines rockbolt. Diese Einrichtung ist anschließend befördert worden, ist beauftragt worden und wird abgezeichnet, prüfen Sie, die Arbeit ist vervollständigt worden, um den Ruckprüfung-Prozeß zu verifizieren. Ein Prüfungsprogramm ist mit dem Objektiv vervollständigt worden, den Lastübertragungsmechanismus zu verstehen und die allgemeine Aufführung von rockbolts zu verbessern. Dieses Papier beschreibt die Ergebnisse dieser Forschung.

Jan 1, 2003

By G. M. Bond

Reduction of the emissions of greenhouse gases, such as CO,, is currently the subject of extensive research. A novel strategy is put forward here, based on a biomimetic approach providing accelerated deposition into carbonate form for long-term sequestration. It offers the advantages of a process that: does not require concentration of CO, from flue gases; could potentially be used in an on-site scrubber to provide a plant-by-plant solution to reducing CO, emissions; is an environmentally benign procss with an environmentally benign product; and is based on readily available, low-cost reagents (except perhaps the catalyst).

Jan 1, 1999

By Stephen M. Smading

The Jinping-II hydroelectric project in China features four parallel headrace tunnels approximately 18-km- (11-mile-) long. Two will be excavated by tunnel boring machines (TBM) and two by drill-and-blast. A nearby fifth tunnel is being excavated by a 7.2-m (23.6-ft) TBM to draw down ground water in advance of excavating the headrace tunnels. Unique onsite assembly of a 12.43-m (40.7-ft) main beam TBM and backup system was completed on Sept. 18, 2008 in the remote mountains of the Sichuan province. The equipment was assembled onsite, without previously having been assembled and tested in a factory, using a method called onsite first time assembly (OFTA). This paper addresses the following topics: ? Project description including geology and terrain. ? The decision process leading to onsite, first time assembly, the assembly process and logistics, and lessons learned. ? Design features of the TBM and backup system. ? Operational history from startup to the writing of this article.

Jan 1, 2009

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By Andrew P. Jarosz

The present computerized mine planning systems use CAD-like and Data Base Management System (DBMS) environments for the handling of numerical, textural, and graphical data. These two environments are usually integrated, that the data provided by the DBMS are linked to any graphical element rendered by the CAD system. The subsidence monitoring, analysis and prediction process should be integrated with the mine design process. It should allow for the assessment of impacts of mining on surface, surface utilities, and structures. It should also provide for the measures to control mining, that will create only acceptable levels of negative impacts on the surface. The common data base, and graphical capabilities of the CAD interface, may be used with great advantage for both systems. The findings of the subsidence engineering modulus should be directly incorporated into the mine design system, and vice versa. In this paper the author suggests guidelines for the development of the comprehensive computer system, able not only to predict the vertical and horizontal components of the ground movement, but also assess the induced surface damages, and costs related to subsidence prevention and compensation.

Jan 1, 1995

By K R. Vining, T E. Norgate

A study was carried out to compare the environmental impacts of the two major iron ore agglomeration processes, sintering and pelletising, using life cycle assessment (LCA) methodology. The following agglomeration processing routes, with the fuel options shown, were investigated:sintering with combined natural gas/coke breeze or charcoal as fuel, grate-kiln pelletising with combined natural gas/coke breeze as fuel, and straight-grate pelletising with combined natural gas/coke breeze as fuel. Inventory data for each process derived from the literature, and in some instances supplemented by additional simulations and calculations, were used in the study and the environmental impact categories considered were gross energy requirement (GER), global warming potential (GWP) and acidification potential (AP). The results of the study showed that the GER, GWP and AP for a sinter plant are higher than those for a pellet plant for the same amount of metallic iron in the agglomerated products. These results are partly due to higher consumption of solid fuel and flux in the sintering process. However, it should be pointed out that the study only compared substantially fluxed sinters with acid pellets that may require additional flux (and hence potentially more greenhouse gases emissions) to be a balanced blast furnace feedstock. Extending the LCA to the blast furnace process stage was beyond the scope of the current study. Within the sinter plant, the sintering stage itself is the largest contributor to the GER, GWP and AP. In the case of pellet plant, the pellet induration stage is the largest contributor to the various environmental impacts. The GER and GWP of a straight-grate pellet plant are marginally higher than those of a grate-kiln pellet plant due to the higher electrical power required by the straight grate system. The substitution of coke breeze with charcoal in the sintering process results in an increase in GER but a decrease in GWP. However, a substantial proportion of the GER is derived from renewable sources (wood), resulting in a decrease in the non-renewable components of this environmental impact. Given the source of the inventory data and the assumptions and approximations made in carrying out the LCAs, it is emphasised that the results presented in this paper should be considered as indicative rather than as definitive results for the two iron ore agglomeration processing routes considered.

Jan 1, 2006

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

An important consideration in any mining operation is waste disposal management. Tailings management at Macraes gold mine allows for the disposal of tailings into fully engineered embankment dams and overburden material to be incorporated as construction material into those embankment dams. This paper outlines the current tailings management practices.

Jan 1, 1992

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By N Phillips

Fosterville gold mine recently celebrated production of its one millionth ounce of gold based firmly within a history of refractory sulfide gold mining. Compared with other Victorian gold mines, the disseminated nature of the sulfide gold is a deposit style with low estimation variance combined with established processes to accurately delineate the controlling structures. The systems in place had been established and have worked effectively for the majority of the one million produced ounces.By the end of 2014, diamond drill campaigns targeting the lower Phoenix orebody at depths of 800 m below surface began showing a change to the nature of the gold within the deposit. Coarse visible gold within 0.5–2 m thick quartz carbonate veins were being intersected with regularity showing the emergence of a different zone of gold mineralisation.Data about the new and exciting discovery couldn’t be gathered fast enough, however, established systems and processes throughout the geology and processing departments were not developed to handle a coarse gold environment. Change would be commensurate with the size and scale of the discovery, and new learnings would need to be implemented quickly to keep in front of a mining schedule that was focused on producing tonnes due to the dropping grades of the sulfide ore.Gold assays being returned were showing that the gold nature was different to those of other Victorian deposits. Comparative to the highly nuggety nature of gold found in other Victorian goldfields, the fine grained gold accumulations were dispersed in relatively consistent narrow linear trends grading consistently into the hundreds of grams per tonne. New drill intersections were being returned by the day and research to find developed orebodies that had published information into how to handle such a rapid change yielded few examples.The challenge was to review and set new standards with regards to handling an orebody that transitioned the very nature of the gold being mined. This involved reviewing all steps in the estimation process including data capture and quality control and quality assurance through to mineral liberation through the mill. Difficulties also involved finding analogous orebodies that consisted of both free milling and refractory ores that were dealing with drill assays that were measured as percentages of gold.CITATION:Phillips, N, 2017. Fosterville gold mine – breaking the mould for Victorian gold, in Proceedings Tenth International Mining Geology Conference 2017, pp 393–400 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By Lyman G. J

Dense medium drum separator efficiency was analysed at two Western Australian iron ore concentrators. Efficiency data had hitherto been difficult to accumulate due to the high cost of analysing representative, and therefore large, coarse ore samples. To overcome this problem, recoverable density tracers, which are in effect artificial mineral and gangue, were manufactured in three different sizes (15 mm, 30 mm and 60 mm). Their use enabled partition curves to be studied within one hour of conducting a test: separation densities were generally lower than the feed medium density for all three sizes of density tracer. For a given set of operating conditions, the smaller tracers had lower separation densities and larger ecart probab/es than the large tracers. These phenomena are explained with the aid of a conceptual model of a drum separator, which assumes that the feed ore plunges to the bottom of the drum upon introduction. Particle rising velocities are, therefore, process determining.Medium rheology was altered by adjusting the proportion of solids in the pulp. This was accomplished by changing both the pulp density and ferrosilicon/magnetite ratio. Higher solids volume fractions invariably caused a decrease in separation densities and an increase in ecart probables, most markedly for the smaller tracers. A similar response was observed when feed tonnages were raised.An explanation for these phenomena is sought in the discussion which also suggests means of improving drum separator efficiency.

Jan 1, 1987

By S. H. E. Phillips

This report describes the initial feasibility, the development and the field demonstration of a system for shaft sinking employing a high energy mechanical impact rock breaker and a compatible muck disposal system. The increased shaft sinking rates, decreased costs and improved safety conditions obtainable by the elimination of the less efficient conventional drill-blast-muck cycles are discussed. Four shaft sinking concepts utilizing the impact rock breaker in various shaft configurations are developed and the field demonstration in a rectangular shaft is described. The progress achieved, the problems and their remedies and the proposed modifications to improve the machine are described.

Jan 1, 1978