Search Documents

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

Traditionally, capital costs of major resource development projects have been estimated as a single amount to which a percentage accuracy has been assigned based on the method of preparation of the estimate, that is, on the amount of information available to develop the estimate.However, there is a growing recognition of the importance of a probabilistic approach to capital cost estimates, and of a more rigorous calculation of estimate accuracies and of the presentation thereof. Accuracies can be expressed with more certainty as a percentage of the estimate amount where the percentage represents one standard distribution on the probability curve for the capital cost of that specific project. Thus confidence levels can be stated for various estimated amounts - for example, it can be stated that there is an 85% chance that a stated amount will not be exceeded, or a 90% certainty that a (higher) amount will not be exceeded. Moreover, the right skewness of the probability distribution curve for most projects can be readily recognised and reflected in the evaluations. This enables senior executives and board members to have a clearer understanding of investment uncertainties, and the possible magnitude of commitments.

Jan 1, 1990

By James L. Oleson, Hunter R. Propsom, Kevan J. R. Ford, Robert D. Henderson, Bob Musgrove

"Kinross’ Fort Knox Gold mine, near Fairbanks, Alaska has successfully implemented two major metallurgical continuous improvement projects resulting in growth of gold production and an extension of mine life. In 2009, Fort Knox produced 263,153 oz of gold at a cash operating cost of $543/oz. In 2010, approximately 63% of the gold will be produced from the CIP circuit, 15% of the gold from the gravity circuit and 22% of the gold from the heap leach.In 2009, a 44,000 ton per day run-of-mine valley fill heap leach facility was constructed and commissioned as a cost effective treatment option for low grade ores to supplement the higher grade mill. The heap leach facility will produce approximately 100,000 ounces of gold per year under severe winter conditions. Heap leach gold recovery, based on test work shows 30% after a 55-day leach cycle, with long term ultimate gold recovery targeted at 65%. The paper presents the heap leach design concepts and production data.Additionally in 2009, installation of a Knelson gravity concentrator unit (XD70) was completed. This together with an Acacia intense leach reactor (AILR) has increased overall mill gold recovery from 79.3% to 80.7%. A manual shaking table gold recovery operation has been replaced by batch intensive cyanidation of the high grade Knelson concentrates. Increased removal of coarse gold and difficult-to-leach gold species from the grinding circuit, via the gravity circuit, has improved gold leach recovery in the conventional whole-ore tank leach CIP circuit. The paper presents plant operating data, showing the improvements over the old flowsheet.Focus on the metallurgical properties of the high grade and low grade end components of the Fort Knox ore has resulted in significant improvement to gold recovery."

Jan 1, 2011

By O. Llewellyn Jack

From September 1978 to December 1983, ESD Corporation (formerly a Division of FMC Corporation) undertook the development and testing of a bidirectional auger under contract with the U.S. Department of Energy. Underground testing began in August 1981 at Peabody Coal Company's Marissa Mine near Marissa, Illinois. The auger was developed to increase mine production and coal recovery without increasing land subsidence. It bored 4-foot-diameter by 10-foot-deep holes into pillars on 7-foot centers (each hole recovering 5 tons). All operating during this test was performed by maintenance personnel with the goal of finding ways to increase the machine potential. The maximum excavation rate achieved was 1.4 tons per minute. It was concluded that the concept of drilling short holes to extract coal from underground pillars without surface subsidence was practicable with a wheel mounted auger, but that more power was desirable for this mine, and that the hydraulically driven augering system that provided experimental versatility was not sufficiently reliable for production use.

Jan 1, 1983

By John C. Stankus

Jennmar Corporation. in an effort to improve mine roof control, has conducted extensive study and research comparing tensioned point anchor resin systems versus the use of non-tensioned fully grouted rehar. Preliminary indications are showing that in thinly laminated, weak strata, tensioned point anchor resin systems are providing more effective roof control than the non-tensioned fully grouted rehar. In this paper two case studies are presented in which tensioned point anchor resin systems were utilized to stabilize and control the mine roof in two different mines. Both mines are alike in many ways, but yet very different in other aspects. However, the mines do share one main common factor. and that being the non-effectiveness of the non-tensioned fully grouted rebar in controlling the thinly lamininated strata in each respective mine.

Jan 1, 1990

The process of gold recovery by gravity concentration is incorporated in the metal recovery flowsheet at seven Newmont Mining Corporation owned mining operations in Australia, North America and Africa. In 2009 gold recovered by gravity processing was equivalent to nine percent of Newmont's total gold sales of 5.3 million ounces. This paper will discuss these applications in detail including a review of plant flowsheets and presentation of recent operating results. Operating performance will be discussed with reference to ore characterisation procedures, interpretation of results, design considerations and optimisation practices as they relate to the recovery of gold by gravity concentration.

Jan 1, 2011

By T. Banerjee, D. Felsher, G. Leavoy

"Lake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2000 tpd tonnes per day (tpd) to over 3,000 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. Without operational data on the low aspect mill, combined with a site team that was new to SAG milling, there were many challenges in achieving the target throughput from the circuit. Through the implementation of AwaRE advanced controllers, running in closed loop with PRC fragmentation cameras as well as embedded PARC modules within the Allen Bradley PLC, the site was able to rapidly develop a best operating practise and has been successful in creating a stable and consistent operational environment. The process, lessons learned and eventual solution will be reviewed in this paper.INTRODUCTIONLake Shore Gold is engaged in commercial gold production at both the Timmins West and Bell Creek mines, located in Timmins, Ontario. Run of mine ore is processed at the Bell Creek mill which consists of a conventional gold mill flow sheet involving crushing, grinding, gravity concentration and carbon-in-leach (CIL) for gold recovery. Since 2009, the operating capacity of the mill has been upgraded from 2,000 tpd tonnes per day (tpd) to 3,150 tpd. The most recent expansion involved the installation of a low aspect ratio SAG mill to replace the secondary crusher. This endeavor was split into two phases: the expansion of the back-end (Phase 1) and the front-end (Phase 2) of the mill. Phase 1 of the expansion was completed at the end of 2012 and involved enhancements and capacity addition to the leaching and adsorption circuits, which increased the mill’s capacity to 2,500 tpd. Phase 2 of the expansion commenced at the end of July 2013 and involved the expansion of the crushing and grinding circuits. The expanded front-end of the mill now has a capacity of 5,500 tpd, and processes ore from both Bell Creek and Timmins West mines. The updated flow-sheet, as shown in Figure 1, illustrates the replacement of the two-stage crushing and ball milling circuit with a single stage crusher and a low aspect ratio SAG mill."

Jan 1, 2015

By Dan A. Brown

The following paper was written by Dr. Dan A. Brown, P.E. Brown is an Associate Professor at Auburn University's Department of Civil Engineering. The paper was originally presented at a FHWA's Transportation Research Board meeting and is presented here with the author's consent. Construction and design of drilled shaft foundations in hard pinnacle limestone requires flexibility from all parties involved due to the variability of the subsurface conditions. This article describes some strategies which have been found useful in the Birmingham, Alabama area. The importance of well trained and experienced field personnel in these conditions is noted. It is also vital that engineers understand the construction challenges so as to provide both quality assurance and cost effectiveness in design and in the specifications.

Jan 1, 1991

By Wilson D, Kirkland J

Compressed air energy storage (CAES) uses low cost off-peak energy to compress air and pump it into pressurised underground storage. Expanding the air through a modified form of gas turbine generates electrical energy when required. While generating power, a CAES station consumes approximately one-third of the gas required for the equivalent installed capacity of a conventional gas turbine. Air can be stored in underground rock caverns, caverns in salt domes, or in aquifers. Existing CAES power stations use caverns mined out of salt domes. Aquifer storage for CAES has been proposed, but not yet implemented. The groundwater in the aquifer would be displaced during air injection and when required the air would be extracted using the natural hydro-static pressure. Victoria has no salt domes, but has aquifers onshore in the Gippsland Basin with geological dome structures of suitable depth, discovery pressure, porosity, permeability and caprock for CAES development. Field tests costing several million dollars would be required to prove the suitability. The most suitable aquifer is near Seaspray, where several dome structures exist. The aquifer, comprising of coarse sands capped by coal and mudstone, is some 600 metres deep with a hydrostatic pressure of 6.3 MPa. Computer simulation of injection and extraction of air from the aquifer under various combinations of horizontal and vertical wells, permeability and tubing head pressures indicated the largest aquifer structure had the capacity to sustain a 300 MW station. A well field comprising of 24 directionally driven wells with a horizontal exposure to the aquifer would achieve the air flow rates required. Using plant similar to that recently installed at McIntosh Alabama USA, would mean high capital costs compared to standard gas turbine plant. However, a review of modem gas turbines indicated that they could be easily and economically adaptated to CAES duty. Adapting a 120 MW gas turbine would give 344 MW output. A separate air compression plant would be used. Economic evaluations indicate that, for gas prices above $1.95 per GJ, a 344 MW CAES plant is more economic for intermediate/reserve load duty than simple cycle gas turbines.

Jan 1, 1992

A general outline of the significant features in the quality and manufacture of the more common refractories is given. Where possible, linkage between quality development and control and service applicationhas been shown and explained. INTRODUCTIONThe refractory industry is no stranger to change. New processes and revision of old processes in other industries are the harbinger of new and revised products in refractories.Few of the changes are dramatic; generally they are evolutionary rather than revolutionary. New developments are additional to, and inclusive of, established practice.Therefore in this paper it is necessary to repeat much of what is already known in order to show the development taking place.FIRECLAY REFRACTORIESGeneral technology Fireclay refractories are the most common, the most varied and the most versatile of all refractories. Virtually any composition of silica and alumina up to the composition of kaolin is possible. For purposes of comparison they may be classified in the Continental fashion in accordance with chemical composition or in the American way according to "duty". That the two methods are equivalent is shown by an inspection of the alumina-silica diagram of Bbwen and Greig (1924). 'Fireclay refractories are composed of a glassy and a crystalline component derived from the chemical and physical nature of the raw materials used in their manufacture.

Jan 1, 1961

Accurately estimating load distributions and ground responses around underground openings play a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the loads that will be carried by them, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses to be used in pillar design. The empirical methods are based on equations derived from large databases of various case studies. They are implemented in government-approved design tools and are widely used. There are also analytical and numerical techniques used for more detailed analysis of the induced loads. In this study, two different longwall mines with different panel width-to-depth ratios are analyzed using different methods. The empirical method used in the analysis is the square decay stress function that uses the abutment angle concept, implemented in pillar design software developed by the National Institute for Occupational Safety and Health (NIOSH). The first numerical method used in the analysis is a displacement-discontinuity (DD) variation of the boundaryelement method, LaModel, which utilizes the laminated overburden model (Heasley, 1998).

Jan 7, 2020

By T. G. Carter, R. I. Miller

First, the influence of variation in the

Apr 1, 1995

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By Linge HG, Fernandez PG, Hughes HC

Aqueous oxidation is a possible alternative to roasting for the processing of gold bearing arsenopyrite (FeAsS) concentrates. The reaction has been studied by voltammetry and this has shown, for the first time, that FeAsS can be readily dissolved without passivation at room temperature in dilute sulphuric acid at relatively modest oxidation potentials (0.7 V SHE). The reaction forms sulphur on the mineral surface and the oxidant consumption is thus minimal. Two practical modes of slurry oxidation are listed.

Jan 1, 1989

Drill cores from Section 62, New Broken Hill Consolidated Ltd., were used to study the petrology of rocks associated with the zinc lode. The distribution of the rock types in relation to the lode structure was determined. The distribution of the gahnite-bearing rocks was shown to be only partly conformable with the structure.It was concluded that large scale metasomatism was not widespread, that the rocks associated with the lode (except, perhaps, the quartz-gahnite-garnet rocks) were formed by metamorphism of sediments, and that rocks and lode were contemporaneously metamorphosed.INTRODUCTIONThis investigation was undertaken in order to study the rock types associated with the zinc lode of the Broken Hill orebody, and their relationship to the structure of the ore horizons. The work was confined almost entirely to the laboratory, and is therefore limited in its scope. It is hoped, however, that the information gained may throw some new light on the genesis of the lode.Certain inferences which are drawn from this work are at variance with the ideas of a number of earlier workers.In particular, the idea of large scale metasomatism developing many of the rocks associated with the lode, especially those containing manganese, is questioned. On the contrary, the rocks associated with the lode are more simply explained as highly metamorphosed sediments, in some cases modified by water introduced from surrounding rocks into zones of strong folding and faulting. As a corollary, a metamorphicsedimentary origin for the lode material, either as a concentrated sulphide deposit, or somewhat disseminated...

Jan 1, 1961

By L A. Maslov

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocity anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain .regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

By Kenneth R. Maser

This report describes a research and development program sponsored by the United State s Bureau of Mines. The purpose of the program was to develop reusable explosion-proof bulkheads for a cross-cut emergency shelter, and to study the implementation of such bulk-heads, and the resulting shelters, as part of an emergency escape plan in a normal coal mining environment. The first part of this report reveals a number of significant conclusions regarding the application of emergency shelters. A study of the cause s of, and the conditions prevailing during a mine emergency indicate s that ideal placement of the shelter s would be midway along developing entries, and at the inter section of butt and main entries. The proper spacing of shelters is based on the travel capability of trapped miners, which is in turn dependent on the height of coal. The life of a given emergency shelter, based on an analysis of the above information, will be anywhere from 6 months to 10 years. Consequently, some shelters are regarded as "temporary?, while others "permanent?.

Jan 1, 1975

By Yi Luo, Jeremy Slagley, Arunkumar Rai, Steve Guffey, Syd S. Peng

Research was conducted to study the characteristics of longwall mining machine noises and to develop engineering controls for the reduction of noise exposure at longwall faces. Time-motion noise dosimeter data was analyzed and compared with existing databases. Experiments were conducted above ground on a stage loader/crusher to explore the potential of using active noise control (noise cancellation) in reducing the noise levels. A 5-7 dBA reduction in recorded stage loader noise was achieved. This paper presents the equipment, procedure and results of the noise surveys, as well as the active noise control experiments.

Jan 1, 2005

Up to the end of World War n, flat-back cut and fill stoping with or without square sets was the universal method of ore extraction. Rapid changes in practice occurred during the post-war years; first, ore extraction was fully mechanized; secondly, the stope design for new levels, notably No. 17 Level Zinc Corporation Ltd. and No. 19 Level New Broken Hill Consolidated Ltd., was modified to suit this mechanization; and thirdly, sub-level and shrinkage stopes were developed in orebodies where cut and fill methods would be uneconomical. The following is a brief survey of the changes that have occurred-most of which were inaugurated during the last five years.ROCK DRILLINGDuring 1951 open stoping was investigated in detail. In order to reduce steel handling problems, forged steel onepass detachable bits were introduced, but were soon superseded by the "Swedish method". Investigation showed that when using a bar and arm mounted 3-in. drifter the overall drilling time was approximately 6 min. per ft. compared with 4 min. per ft. using the light jackhammer-airleg combination with 1-in. hex. by 4-in. collared shank tungsten carbide-tipped steel.Although competitive with tipped steels on a cost per foot drilled basis (excluding miner's time), detachable steel bits proved most unsatisfactory for hard drilling conditions.Rapid blunting necessitated frequent bit changes and thus caused lost drilling time. This, together with rapid gauge...

Jan 1, 1957