Search Documents

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Yutaka Saito

"Effect of moisture content must be fully understood for controlling the granule compaction of ceramics. It changes the mechanical behavior of spray-dried granules applied for compaction process, and governs the structure and properties of .ceramics. To understand the time-dependent change in processing, the kinetics was examined for change of moisture content for granules placed in a die and the pressed compacts also. The results were explained in terms of apparent moisture diffusion coefficients. They varied non-linearly with the PVA content in the granules. The results were explained through the non-uniform PVA distribution in the granules.IntroductionMoisture must be controlled in compaction process to produce the green compacts having uniform structure. It affects glass transition temperature of binder and thus the deformation behavior of powder granules under an applied stress. Several studies [1-7] have clarified the effect of moisture content on the compaction behavior of granules and the structure of resultant compacts for both die pressing and cold isostatic pressing (CIP) of pre-formed compacts. In these studies, the moisture contents in the system were equilibrated with the humidity in the atmosphere before compaction. In practice, however, the moisture content in the system may vary with time if the relative humidity of surrounding atmosphere is different from what the granules were equilibrated previously. This is very likely case in real production processes. However, the kinetics of moisture change in the granules as well as in the pre-formed powder compacts have not been well studied. For controlling the microstructure in a system, it is necessary to fully understand the kinetics of moisture change and its relevance to packing structure of powders."

Jan 1, 2000

By Christopher B. Vierrether

Reflected light microscopy, scanning electron microscopy, and electron microprobe analysis have been used to determine the mineralogy, phase percentages, grain sizes, textures, and partitioning of cobalt and nickel in two cobalt-nickel rich mattes. These mattes were prepared by submerged bath smelting from a flotation cobalt-nickel concentrate containing 4.8% cobalt and 5.1% nickel. The concentrate was derived from lead-zinc-copper ores of the Viburnum Trend, southeast Missouri. Eleven discrete phases have been distinguished in the matte samples, three of which contain significant cobalt and nickel. The phases are cobaltpentlandite ((Co,Ni,Fe)9S8), cobalt-bearing marmatite ((Co,Fe,Zn)S), shandite (Ni3Pb2S2), bornite (Cu5FeS4), galena (PbS), magnetite (Fe3O4), pyrrhotite ((Co,Ni,Cu,Fe)1_xS), chalcocite (Cu2S), CuPbS phase, metallic copper, and metallic silver. Cobaltpentlandite and cobalt-bearing marmatite- occur in coarse grains (50 µm) that would separate readily during grinding, but shandite contains small (5 - 10um), abundant inclusions of pyrrhotite and bornite.. Some mineralogical variations between the two matte samples were due to differing degrees of oxidation during smelting,

Jan 1, 1988

By Francois Reizine

Infrared sensors will include scanning detectors and positioning sensors. The focus will be on 1, 2, and 4-color wavelength pyrometer systems which allow the accurate measurement of emissivity and, consequently, of the true temperature even in the presence of scale, slag, and fumes. Such sensors are being used in blast furnaces, BOF's, and galvanizing lines. Laser sensors will be presented using different principles of physics, mainly time-of-flight, pulsed infrared lasers for level measurement and dimensional measurement; triangulation lasers for width and thickness measurements; and laser Doppler velocimeters for velocity and length measurements, including mass flow, elongation, and tension control, cut-to-length applications. These sensors and systems are based on state-of-the-art technical developments to improve productivity and quality and reduce maintenance and downtime.

Jan 1, 2001

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Pingchao Ke

A crystalline polyferric sulfate (PFS) adsorbent was synthesized by oxidizing and precipitating ferrous ions under atmospheric conditions. The morphology, structure, composition and specific surface area (SSA) and adsorptive efficacy to As (III) of the adsorbent were characterized by SEM/EDS and TEM images, XRD patterns, FT-IR spectra, BET SSA analyses and adsorption experiments. The adsorbent presents as morphology of near-spherical aggregate and good crystallinity. A small amount of goethite co-precipitated with PFS in the case of the initial ferrous concentration of 1 mol/L and increased the SSA of the aggregates. The absorbent with co-precipitation of goethite showed good adsorption to As(III) and good filtering performance in the high As(III)-content solution of 10–100 mg/L under acidic, neutral and alkaline conditions (pH 2.09–9.01), and its maximal adsorption capacity and adsorption efficiency were 7911 μg/g and 96% separately. After Adsorption, the stability of the absorbents adsorbing As(III) were evaluated by TCLP tests, and the results indicated that the absorbents adsorbing As(III) were extremely stable, and the concentration of arsenic in all leaching solutions were less than 0.01 mg/L.

By Jan Dabrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures at each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 2D graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mu, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By E. F. Vegman, Ndabezinhle Dube

"In the practice of conventional sintering, production is always afflicted with the problem of being unable to get a uniform quality of produced sinter in the bed. Invariably the top layer of the sinter cake is composed of weak but highly sinter, while the bottom layer is over-fused, forming a sinter that is very strong but less reducible. These symptoms point to a variable distribution of the heat balance in the process of sintering which results in a deficit of heat in the top layers of the sinter bed and an excess of heat in the bottom layers, due to an increasing input of regenerated heat in the heat balance down the bed. This causes losses in the productivities of the sinter machine and the blast furnace.The current work was designed to improve on the solution to the above problem through the establishment of a more accurate combustion zone heat balance of the sintering process. This development is mostly on the method of determining the regenerated heat input in the overall heat balance. Previous methods were based on the assumption that the width and the velocity of the combustion zone remain constant through out its whole life, which is not the case since tests have shown that both its width and velocity increase as the combustion zone moves down the bed. In this work, these factors have been taken into account. Tests and calculations using the model were carried out for haematite and limonitic ores. The high sensitivity of the model to changes in the sinter mix composition and sintering conditions was demonstrated.The results present the following prospects:• The minimum theoretically possible coke breeze consumption during the sintering of any type of iron ore fines, under any sintering conditions, can be established.• The model can be used to control the metallurgical quality of the sinter in any point in the sinter bed since calculation data includes desired basicity, combustion zone temperature and FeO content in the sinter produced."

Jan 1, 2001

By Walter E. Dean

Twenty six samples of carbonaceous gold ores and associated rocks from outcrop and mine localities in northcentral Nevada were analyzed for concentrations of major. minor, and trace elements, total sulfur, and organic carbon. Q-mode factor analysis was used to define six distinctive carbonate, organic, and detrital associations of elements, and to group samples based on these associations. The trace metals that have clearly enriched the organic-carbon-rich samples are V, Zn, Ni, Cu, Cr, and Mo, although few of the samples could be considered "metal-rich" when compared to other organic-carbon-rich black shales. Rock-Eval pyrolysis was used to evaluate thermal maturity and hydrocarbon yield of the samples. Unfortunately, most samples were too thermally altered to be suitable for routine organic geochemical characterization of organic matter. The 813C values of organic carbon in rocks from different deposits have a trimodal distribution, but there is no clear distinction between the three groups of deposits that can be related to age, thermal history, or depositional environment.

Jan 1, 1987

By G. J. Abbaschian, A. B. Gokhale, M. M. Kunjapur

"A laboratory scale model furnace was constructed for obtaining radially inward oriented columnar grains in disc shaped castings. The furnace consisted of eleven circular, concentric, equispaced resistance heaters on each half of a split graphite mold. Water or air flowing through a copper pipe along the periphery of the disc constituted the heat sink. After filling the mold, the heaters were turned off consecutively in top and bottom pairs from the rim towards the center, causing the temperature gradients to move inward. Equiaxed structure was obtained at the center by turning off the inner coils together when desired. Sn:15%Pb alloy was used to cast integral blade disc castings using the above technique to obtain dual-property discs with a central equiaxed structure and an outer columnar grain structure projecting inwards from the blades to the rim. A numerical technique was used to predict the temperature profile in the disc during solidification, and good correlation was obtained with the experimentally measured temperature profiles. The corresponding heat transfer coefficient values obtained were h = 544 Wm- 2k-1 (0.013 cal/cm2- ° C-sec) for cooling between metal and chill and h' = 71 Wm- 2k-1 (0.0017 cal/cm2- ° C-sec) for the heat input from the hot mold to the liquid metal. BackgroundHigh temperature alloys used in the current generation of gas turbine engines have evolved through two main stages of development: in 1950's, the increase in the efficiency of gas turbines was paced by improvements in alloy design, which led to the development of Ni and Co-based superalloys (1). By mid-1960's, it was realized that improved alloy chemistry alone was inadequate in meeting the increasingly stringent service requirements. The focus of research then shifted from alloy development to process development, and resulted in the introduction of directional solidification (DS) techniques for the production of turbine blades and vanes (1,2).Under typical operating conditions, the blades and vanes are subjected to aerodynamic loading, while the blades are additionally subjected to high centrifugal loading and vibratory stresses. The primary material requirements for blades may be summarized as follows (1,3):•,High creep resistance•,Good high temperature tensile strength (typically in the range of•,275 to 550 MPa at temperatures in excess of 750°C)•,Resistance to both low cycle and high cycle fatigue (LCF and HCF)•,Resistance to erosion, corrosion, and oxidation•,Resistance to thermal fatigue"

Jan 1, 1986

By A. E. Isaacson

The U.S. Bureau of Mines is studying the effect of supercritical water, at 400' C and 3,500 psi, and subcritical water, at lower temperatures and pressures, on mixtures of minerals and metals to determine the possible applications of water at high temperature and pressure for processing these materials. This research was conducted using a flow-through bench-scale system. Copper-bearing minerals studied were chalcocite, chalcopyrite, covellite, and cuprite. In general, mixtures of copper minerals and pyrite reacted to form bornite. Intermediate phases formed were chalcopyrite and digenite. Similar reactions occurred between pyrite and metallic copper. A mixture of chalcopyrite and pyrite was inert in supercritical water'. The reaction between cuprite and metallic zinc yielded metallic copper. The cuprite was reduced by hydrogen generated by the reaction between metallic zinc and water. None of the reactions occurred exclusively in supercritical water, but also occurred in water at high temperature and pressure below the critical point. 'Experimental results did show that a dual-reaction process, consisting of solid-state diffusion and fluid transport, was occurring.

Jan 1, 1989

By Norbert Hort, Karl Ulrich Kainer, Carsten Blawert, Daniel Fechner

"With the development of new heat resistant magnesium alloys, the automotive industry has introduced several parts to the drive train. The rising number of large magnesium components will result in a higher quantity of automotive post consumer scrap and the changing legislation will force car manufacturers to take magnesium recycling into consideration. So far post consumer scrap has not been used for magnesium alloy production. Quite a reasonable amount of automotive scrap is likely to end up in a mixed light metal shredder fraction. The separation of mixed magnesium scrap according to several alloys is complex. Therefore secondary magnesium alloys made from blended post consumer scrap would be useful. For this work a matrix of potential recycling alloys was prepared by chill casting and high pressure die casting. The materials were investigated for their microstructure, mechanical properties, heat resistance and corrosion properties. The results will be presented in this paper.IntroductionWithin the last ten to fifteen years several heavy magnesium parts have been assembled in passenger cars, such as gear box housings and crank cases [1, 2]. Reasons are the lately developed new heat resistant alloys and the increasing responsibility of automotive manufacturers to reduce the vehicles weight and thereby CO2 emissions. The latter is pushed by international legislation [3, 4]. The rising quantity of magnesium in automobiles will result in an increasing amount of so called post consumer scrap at the end of the vehicles life.So far magnesium recycling was done only for clean scrap that is free from impurities, contaminations and sorted according to a chemical composition or a single alloy respectively [5- 15]. The latter is also called class 1 scrap and mainly consists of sprues and runners from magnesium die casters [15, 16]. For the upcoming automotive post consumer scrap the materials quality strongly depends on the way end of life vehicles are treated. By proper dismantling of old cars, the bigger magnesium components could be collected and possibly treated similar to class 1 scrap [15]. Up to date automotive manufacturers have no uniform recycling system for end of live vehicles. Most probably a considerable quantity of old cars will be shredded. The resulting light metal shredder fraction will contain aluminium and magnesium scrap, both from several alloys. A separation of mixed magnesium and aluminium scrap is feasible according to [17]. Other authors claimed that the grade of separation of magnesium from aluminium is still not sufficient for a proper industrial recycling process of magnesium post consumer scrap [15, 16]. If an automatic sorting is possible it will probably be very expensive [18]. Therefore, so far the main use of post consumer scrap has been the steel desulphurisation and aluminium production [15]. The use of post consumer scrap for magnesium alloy production has been considered already by [15] and [16] but some problems have to be approached."

Jan 1, 2008

By Jerome P. Downey

In the thermal treatment of electric arc furnace (EAF) dusts, zinc is reduced, volatilized, and ultimately recovered either as liquid metal in a splash condenser or as solid zinc oxide in bag filters. During the process, the duet's chlorine and fluorine content also enters the gas phase and condenses as dross in the splash condenser or as salts which contaminate the zinc oxide product. Pretreatment of EAF dust by pyrohydrolysis appeared to offer a means of minimizing the duet's halogen content. The primary research objectives were to experimentally verify the technical viability of pyrohydrolysis and delineate the process parameters requisite for efficient halogen removal. To this end, representative EAF duet samples were secured and characterized by x-ray diffraction, scanning electron microscopy, and Mössbauer analyses. Specific- experimentation focused on the response of halogen extraction to variations in temperature, retention time, water vapor partial pressure, and various additives. The experimental results proved that 97 to 99 percent chlorine extraction and 80 to 85 percent fluorine extraction are consistently achieved when EAF dusts are blended with silica and roasted at temperatures of 850°C or greater in a furnace atmosphere of 75% steam (diluted by air). A statistical analysis further established that more than- a single optimal point exists, thus affording flexibility in parameter selection (e.g., by increasing temperature, the necessary retention time and additive concentrations are decreased). The findings substantiate the feasibility of pyrohydrolysis roasting in reducing the chlorine and fluorine in the EAF dust to a level that will obviate industrial concerns about halogen contamination. The end-product of the pyrohydrolysis procedure is a de-halogenated, self-fluxing calcine which can be directly charged to a plasma or flame reactor. The paper includes design parameters and flow diagrams illustrating the pyrohydrolysis process integrated with the plasma and flame reactor technologies.

Jan 1, 1992

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994

By Mingmei Zhu, Xin Qiu, Xiaofei Dou, Yu Wang, Tiancheng Lin, Bing Xie

In this study, the slag forming route of the single-slag steel melting when smelting medium phosphorus hot metal was investigated. The CaO-SiO2-FeO-MgO-MnO-P2O5 as hexahydric slag system was adopted in the converter. The effect of slag composition on liquidus was calculated by FactSage, the isogram of phosphorus distribution ratio was calculated by using the regular ion solution model, combining these two tasks, the theoretical slag forming route was obtained. Through experiments, the actual melting point ofthe corresponding components on theoretical slag forming route was obtained, in this way, the theoretical slag forming route was confirmed. Then, the theoretical slag forming route was applied to industrial test in a 210t BOF. After using the new slag formating route, the dephosphorization ratio was increased 3.6% while the auxiliary materials consumption was reduced, and the cost of steelmaking was reduced.

Jan 1, 2015

By Robert Hanson, Mayur K. Patel

"Pneumatic conveying pipelines are used throughout a variety of industries, from food processing/packing to power generation plants, as an efficient means of transporting materials between storage and processing points. In general, different phases of pneumatic conveying exist when material is conveyed from point A to point B in a pipeline. This depends on the operating pressure and the material conveyed. Lean phase conveying exists when pipelines are operated at high airflow rates, relatively low pressures, inducing sufficient turbulence for particles to become entrained in the air stream. Thus, particles are conveyed along the pipelines at velocities in the range of IS-2Sm/s. Generally, the initial capital costs for lean phase system is low, however the running costs are high. The opposite is true for dense phase, high-pressure systems. In considering either conveying system, it is important that the rate of erosion of the pipeline be considered when designing such a system, since it is the rate of erosion that dictates the lifetime of components. In general, the high level of erosion occurs for lean phase flows, where high impact velocity contribute substantially to the rate of erosion as well as other processes such as particle breaking, if the particles are friable. This would lead to poor quality of material, not normally desirable. On a positive note, the process of erosion is used in other applications, which benefits from this process, e.g. abrasive guns.The failure, by puncture, of pneumatic conveyor bends in industry causes several major problems. Two of these are: (a) escape of the conveyed product causing health and dust hazard and (b) repairing and cleaning up after punctures necessitates shutting down conveyors, which will affect the operation ofthe plant, thus reducing profitability.The paper reports on modelling strategy used in the development of a modelling framework and the initial validation phases of the models incorporated within. The modelling framework encompasses Computational Fluid Dynamics (CFD) related engineering tools, based on Eulerian (gas) and Lagrangian (particle) approaches, to represent the two distinct conveyed phases, to represent the erosion process which is used to ascertain the lifetime of conveyor bends."

Jan 1, 2001

By Pekka Taskinen

The converter-less nickel matte smelting technology (DON) adopted more than 20 years ago in Boliden Harjavalta smelter has been since that applied successfully to the processing of large number of nickel sulphide concentrates of various Ni-to-Cu ratios and MgO contents. The operational point of the technology is far from the conventional primary nickel smelting in the smelting-converting route. Therefore, a careful scouting of distribution equilibria of the base and trace elements in the smelting conditions of DON process has been conducted, in order to obtain quantitative information about the equilibria and thermodynamic properties of the nickel mattes at low iron concentrations, less than 10 wt% [Fe] in matte. The series of investigations has included novel experimental and analytical techniques for increasing the reliability and sensitivity of the phase equilibria as well as the element distribution observations carried out in typical high-grade nickel matte smelting conditions.

By Jilai Xue, Jun Zhu, Liang Liu

"Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice with a heating process causing large energy consumption and high production costs. In this work, the floatation separation at room temperature were carried out using two types of skarn scheelite ores. The results showed that CaO and Na203 are better than NaOH as a regulator in pH value. In the rough floatation and first cleaning floatation, CaO (500g/t), Na203 (3000g/t) were used as a pH regulator, waterglass (4000g/t) was as a gangue depressant, oleic acid or sodium oleate were used as a collector. The degree of the obtained W03 concentrate was more than 65% (commercial product).IntroductionThe mainly gangue in scheelite are quartz, calcite, barite and some rare metal ores. There are three main types of scheelite for floatation: scheelite--quartz (silicate minerals) type, scheelite-calcite/ fluorite type, scheelite--calcite/fluorite/barite type. Generally speaking, scheelite--quartz type is separated easily, and others are difficult, on the contrary. The last two kinds of scheelite are always called scheelite--calcite/fluorite (barite) type, because there are similar floatation ability and floatation process between them. Scheelite, calcite and fluorite have same cation - Ca2+, it makes them have close floatation property [1]. Separation removal of fluorite and calcite from scheelite is a difficult technical operation in current industrial practice.The traditional separation method is a heating floatation process (Petrov's process) [2]. It can deal with many kinds of scheelite, and can be obtained stable quality ofW03 concentrate. On the other hand Petrov's process causes large energy consumption, high production costs and bad operational environments. Since 1980s, scheelite ambient temperature floatation has become the mainstream of study [3]. Nowadays more and more studies on scheelite floatation focus on complex reagent system [4, 5], rigid operating rules and at the same time development new regulator [1, 5]. Some research show there are new regulators can concentrate scheelite efficiently, but it may cause high costs, potential pollution and difficulty to spread. Oleic acid and sodium oleate used as collector have high adsorption capacity to scheelite, but same to calcite and fluorite[6]. So, it would not get ideal effect for separation of scheelite. In this work, the floatation separation at room temperature were carried out using two kinds of skarn scheelite ores. Calcium oxide and sodium carbonate was used as a pH value regulator, waterglass was used as a depressant and Oleic acid/sodium oleate was used as a collector. The result of experiment showed that the degree of the obtained W03 concentrate was more than 65% by one time ambient temperature roughing floatation, several times ambient temperature cleaning process."

Jan 1, 2014

By John W. Cash

The mineralogy and textures of cyclone dust, sludge, and occasional build-ups in the American Iron and Steel Institute (AISI) direct ironmaking pilot plant at Universal, Pennsylvania have been studied by reflected light, transmitted light, and cathodoluminescence microscopy, and phase compositions have been determined by SEM-EDS. The cyclone dust consists of particles of carbon, metallic iron, sulfur-bearing iron, and wustite. Measurements of particles in the sludge indicates that 69% are less than 2.5 um across, 21 % are 2.5-5 um, and 10% are larger than 5 um. Mineralogically the sludge particles are mainly carbon and metallic iron, with minor wustite and sulfur-bearing iron. Build-ups that sporadically develop in the furnace consist of olivine, hercynite spinel, metallic iron, wustite, pyrrhotite, pseudobrookite, akermanite-ferroakermanite and gehlenite. The microtextures shown by the build-ups indicate that much of that material has precipitated at the build-up loci. This study has been supported by AISI and the U.S. Department of Energy.

Jan 1, 1995

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By E. Ozberk

The copper and nickel smelting industries are important contributors to the technical and economic well-being of Canada while some of the smelters are among the largest sources of sulphur dioxide emissions in Canada. A review of the operations in six smelters - Falconbridge Limited, Falconbridge, Ontario; Hudson Bay Mining and Smelting Co. Limited, Flin Flon, Manitoba; Inco Limited, Copper Cliff, Ontario and Thompson, Manitoba; Noranda Mines Limited, Horne Division, Noranda, Quebec and Gaspe Mines Division, Murdochville, Quebec - have shown that about 80% of the total sulphur input to these smelters was emitted to the atmosphere in 1980. A simultaneous review of the existing and emerging technologies which can directly or indirectly reduce the sulphur dioxide emissions indicated that it is possible to reduce the emissions to below 20% of the sulphur input to these smelters. This can be achieved by varying degrees of modifications to the smelting operations and installing sulphur fixation facilities at significant costs which may increase the metal production costs. This would consequently make the competitiveness of the Canadian copper and nickel producers more difficult in the already tough world metals market.

Jan 1, 1983