Search Documents

By Elli Nurminen

Fouling of heat recovery process equipment may significantly decrease their heat transfer efficiency. In Copper Flash Smelting process flue dust tends to form build-ups on the heat recovery boiler walls. Thermal transportation properties of copper flash smelting flue dust and its components have been studied. The effects of porosity and temperature on thermal transportation properties have also been determined. The results indicate that dust and its components are effective thermal insulators and build-up layers on the boiler walls are likely to decrease greatly the heat transfer efficiency of the boiler. Decreasing dust layer porosity has a strong increasing effect on thermal conductivity and increasing temperature has a slight decreasing effect on thermal conductivity. The results may be used in CFD-modelling and optimisation of the process.

Jan 1, 2006

By Huang Rui

The coal asphalt is combusted at different temperature in a heating cabinet with the temperature limit by 1200°C. By comparing the mass of the remainder of each experiment, the completely combusting temperature of asphalt smoke can be determined. Based on the experimental process of asphalt smoke, a discrete mathematical model of the asphalt smoke combustion is set by theoretic analysis. Through computer programming, the dynamic combustion process of asphalt smoke is calculated to simulate the experimental model. The result of experiment shows that coal asphalt can mostly react upon 500°C and the mass of remainder is 49.41% to initial mass of sample in the condition. The computing result shows that the temperature and the concentration of asphalt smoke influence its burning temperature approximating linearity. The consumed quantity of fuel to ignite the asphalt smoke needs be considered with the two factors.

Jan 1, 2006

By Christian Hecker

An Eh-pH electrochemical sensor developed for on-line pH and redox potentials copper sulphide flotation process control was studied. The electrochemical sensor cell includes two metallic platinum electrodes, a metallic antimony electrode and a high impedance reference cell which are polarized with a potentiostat. For pH and redox potential determinations, the Sb and platinum electrode potentials are measured, respectively, against the polarized electrochemical reference system. The behaviour of this electrode configuration has been investigated in a laboratory scale. An electrochemical sensor device has been succesfully installed and checked in El Teninte Colon Concentrator's SAG line feeding the copper flotation rougher circuit.

Jan 1, 1999

By A. A. Shook

The off gas from the #5 converter at BHP Copper's San Manuel smelter was analyzed continuously over a period of several weeks using an online sulfur dioxide analyzer. These data have shown that the oxygen utilization efficiency of this copper converter was somewhat lower than anticipated, and that oxygen efficiency declines significantly during the copper blow. A sharp reduction in sulfur dioxide generation was consistently observed at the end of the copper blow, which could be used by converter operators to prevent over-blowing and minimize rolling out of stack.

Jan 1, 1999

By Patricio F. Mendez

This paper presents a formalism to automate portions of the traditional scaling procedure. This formalism, called here Order of Magnitude Scaling (OMS), captures essential components of the governing equations into a set of matrices and arrays amenable to computer implementation using standard linear algebra tools. This approach is valid and specially useful for large systems of multicoupled equations. The matrix approach proposed enables one to automate operations such as normalization, dominant balance, obtention of characteristic values, and check for self-consistency. Also, automation permits an exhaustive exploration of all possible balances and the discovery of unsuspected scaling laws. As an example, OMS is applied to the analysis of the viscous boundary layer with no external pressure gradient. The obtained scaling laws for boundary layer thickness and transverse velocity are the same as those obtained with traditional scaling, and in addition, a meaningful estimation for pressure variations within the boundary layer is obtained; this last estimation is typically not addressed in the manual analysis.

Jan 1, 2006

By N. L. Piret, E. N. Mounsey

Ausmelt technology is successfully used to process primary and secondary materials to produce lead in large-scale commercial operations and to meet stringent environmental standards. The development and commercial data covering these applications and the results with respect to metallurgical, cost and environmental performance are reviewed in commercial operations. A new smelter is scheduled for commissioning in 2000 at Korea Zinc's Onsan site to process lead fume and other secondary materials to produce 50,000 tonnes per annum of lead bullion. The unique features of Ausmelt technology also allow for the efficient processing of polymetallic concentrates and secondary materials, particularly copper and lead, through the effective separation of these elements into metal, slag and fume species. This capability has been successfully demonstrated at a commercial scale and the results and implications for the industry are discussed.

Jan 1, 2000

By A. V. Tarasov

The high efficiency of autoclave processes is attributed to the fact that they are suitable for processing of refractory raw materials, have low capital costs and high productivity, ensure integrated utilization of the feed materials, produce innovative saleable products, completely eliminate any air emissions, provide low-waste or waste-less technology, as well as mechanization and automation of production processes. In the immediate future, it might be expected that autoclave processes will find use on commercial scale for production of heavy non-ferrous metals in combination with other processes (hydrometallurgical, upgrading, sorption and solvent extraction, electrolytic, etc.) to ensure: -Integrated processing of refractory ores and concentrates (pyrrhotite, zinc, copper-zinc, lead-zinc, nickel-cobalt, copper, pyrite); -Production of metallic powders of base metals as commercial products (copper, cobalt, nickel, etc.), composites on their bases, final products and saleable salts. Processing technologies incorporating autoclave processes, especially, at the stage of liberation (chemical upgrading) of minerals, are characterized generally by high overall recoveries of valuable constituents significantly exceeding recoveries common for conventional pyrometallurgical processes (for some elements by several tens of percent). An example is processing of low-grade refractory pyrrhotite concentrates using autoclave liberation of feed material under pressure of a new reagent, i.e., sulfur dioxide. The use of sulfur dioxide ensures a significant improvement in the recoveries of non-ferrous metals and platinoids to sulfide concentrate and smelting of the latter increases the capacity of the smelting units employed and minimizes the yield of discard slag and loss of metals in slag; in addition, it resolves the problem of sulfur dioxide utilization.

Jan 1, 2003

By A. L. Davies

The MTDATA computer software package consists of a rigorous implementation of an algorithm for calculating chemical phase equilibria by the technique of Gibbs free energy minimization and a database of the thermochemical properties of common materials, such as slags, mattes, metals, gases and aqueous solutions. We have used MTDATA to contribute to our understanding of the chemical reactions occurring in several specific unit operations of the Kennecott Utah Copper Garfield Smelter. The following two examples illustrate the range of environments to which the method is applicable. Calculation of the liquidus phase relations of the FSF fayalite and FCF calcium ferrite slags helped in the early diagnosis of several operating problems. Calculation of the deportment of fluorine between the FSF offgas and the FSG scrubber liquor helped in the identification of operating conditions under which significant hydrogen fluoride concentrations could be introduced to the contact section of the acid plant. Without the painstaking assessment of solution phase properties undertaken over many years, these calculations would not be possible.

Jan 1, 1999

By F. M. Doyle, K. Sreenivasarao

Copper and cadmium metal has been recovered from dilute (3 X 10-4 mol/dm3 ) chloride solutions by ion flotation with dodecysulfate, followed by electrolysis. This approach should facilitate treatment of effluents too dilute for effective direct electrolysis. . The adsorption density of metal dodecylsulfate complexes on bubble surfaces was estimated from surface, tension data, and compared well with experimentally-observed metal removal kinetics, and ultimate recoveries. Copper and cadmium were recovered by electrolyzing the foamate, using steel wool cathodes and a graphite anode. The stability constants of the copper and cadmium dodecysulfate complexes are estimated, and used to analyze the thermodynamics of electrolysis. Dodecysulfate was unaffected by the electrolysis process, and hence could be recycled to ion flotation. A conceptual flowsheet for an overall effluent-treatment process is presented.

Jan 1, 1997

By Susan A. Fredholm, Randolph E. Kirchain, Elsa A. Olivetti, Jeremy R. Gregory, Jeffrey B. Dahmus

"A general model for evaluating the economic and environmental performance of electronics recycling systems is developed. This model comprehends the three main functions in a recycling system – collection, processing, and system management – and aims to enable quantification of the impact of context and system architecture on the economic and environmental performance of electronics recycling systems. Such a model can be used both to evaluate and improve existing electronics recycling systems, as well as to design and implement new systems. A case study, based loosely on Maine, is presented to show the utility of such a model.IntroductionAs recycling systems for complex durable goods (CDGs), and in particular for waste electronics, become more widespread, understanding the economic and environmental performance of such systems becomes critical, both to enable improvement of existing systems and to inform the design of new systems. However, with the range of possible system architectures and the important role of locational characteristics (context), understanding the determinants of system performance is challenging [1]. To address this issue, a modeling framework to project the economic and environmental performance of CDG recycling systems, based on contextual and architectural characteristics, has been developed.The modeling framework presented here comprehends the three main functions – collection, processing, and system management – which are common to most recycling systems. These three functions are modeled using a variety of modeling techniques and serve as a bridge between inputs related to system context and system architecture, and outputs related to economic and environmental performance. The models developed here are intentionally meant to be both broad, in order to address entire recycling systems, and general, such that many different systems, both real and hypothetical, can be analyzed."

Jan 1, 2008

By B. Holleis, M. Potesser, D. Spoljaric, H. Antrekowitsch, A. Hengelmolen

"During the past only an optimization of metallurgical furnaces were done without attention on the burners. Nevertheless, furnaces without burners are impossible to use in the primary and secondary nonferrous metallurgy in an economic way. Since the energy cost is increasing and the environmental protection is becoming a global issue, the burners are in the focus of several investigations and optimizations. One possible way is the combustion by oxygen. By using oxygen, the flame temperature increases and therefore, fuel accordingly money could be saved by having a low amount of harmful substances like NOx in the off gas. This paper describes a new burner system which combusts fuel with oxygen or air by diluted combustion, hence low pollutants in the off gas. Furthermore the effectiveness of the burner characterized by off gas analyses and simulation in the new development chamber, but also practical tests at an aluminum smelter are described.IntroductionIn 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today’s and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Wärme-Institut “GWI” in Essen (Germany) and the University of Leoben, different new burners have been developed."

Jan 1, 2008

By Ioannis Paspaliaris, Dimitrios I. Gerogiorgis, Dimitrios Panias

"Red mud fiberization is a process with remarkable potential, alleviating environmental pressure by transforming an aluminum by-product into mineral wool, thus to various marketable products. A promising mineral wool process is molten slag fiberization via an impinging air jet, which avoids mechanical wear and rotating parts. The molten slag which remains after pig iron casting flows out of a heated ladle orifice at a high temperature (1600 °C) and adjustable flowrate, and forms a free-falling vertical jet which visibly radiates its excessive heat: at a given distance, a high-velocity impinging air jet meets the vertical melt jet perpendicularly (or at an angle), inducing intensive droplet generation, subsequent fiber elongation, collection and processing.This paper focuses on high-fidelity CFD modeling of the molten jet flow under external cooling: the model encompasses all physicochemical phenomena (melt laminar flow, radiative cooling) and considers several temperature-dependent slag transport properties in order to understand which operational degrees of freedom (manipulated variables) are useful to process optimization."

Jan 1, 2012

By Viktor Mukhin

"Among the methods proposed for spent activated carbon regeneration, the most acceptable is, thermal reactivation, because in this case the existing equipment for manufacture of activated carbon can be adapted for this purpose.In order to conduct the process of thermal re-activation of spent activated carbon directly at gold mills, a fullscale drum-type furnace with external electric heating has been developed, i.e. EPV-300 model with a throughput rate of 50 to 120 kg/hour. Its use ensures restoration of the adsorption properties of carbon up to the level of fresh activated carbon with an insignificant (by 0.7%) decrease in strength and with a high (95% to 97%) yield of reactivated carbon.During the recent years, activated powder carbon has been extensively used in flotation processes for treating polymetallic ores at ore treating plants to improve recoveries of main metals (copper, lead, nickel, etc.).Especially large volumes of activated powder carbon are used at the Talnakh concentrator of the Norilsk Mining and Metallurgical Complex in Russia for absorption of residual flotation reagents from recycled water in order to ensure efficient selective separation of minerals with similar physical and chemical properties.IntroductionSorption technology based on active carbons use starts being applied in such an important in the widest sense of the word strategical branch of economics as non-ferrous metallurgy. Thus since the middle ninetieth Russian gold extraction industry began to apply widely the processes of sorption from pulps and solutions by means of high-resistant granulated active carbons. That provided the start of gold ore minefield exploration, increasing of gold extraction from the ore and reducing its loss with the ""tails"" of process. At present more than 40% of Russian gold is extracted with the help of sorption technologies [1].Another field of active carbons application in non-ferrous metallurgy is the processes of non-ferrous ores floatation at ore-mining and processing enterprise. For that purpose powdered (less than l00µm) active carbons are used for providing the effective selection of minerals with similar physicochemical properties. This method not only increases the metal extraction level but provides deeper division of them."

Jan 1, 2008

By William James Middleton

The life-cycle assessment (LCA) approach can be an important tool for the quantification and evaluation of environmental impacts associated with metal production systems. At the conceptual phase of a new metals development project, LCA can: ? Aid project decision making by evaluating the environmental consequences of design decisions ? Support project permitting and reinforce site/process environmental impact assessment ? Allow environmental impact comparisons between alternate flow sheets For existing metals production systems, LCA has been used to aid targeted process improvements by monitoring recent historical trends in environmental performance, either through local or external (externalities) process improvements. This paper discusses the life- cycle assessment methodology, and its application as a supportive tool for environmental decision-making in process design and operation, and for site environmental impact assessment and permitting. Selected examples from a recent LCA performed on the Pressure Acid Leach Process for treating nickel Laterite ores are employed to demonstrate the usefulness of the tool.

Jan 1, 2004

By A. N. Aposhian

The electronics industry generates tin/lead bearing by-products that can be recycled for their metal value. This paper will cover the processes used to recycle these tin/lead bearing byproducts from the plating, circuit-board fabrication and assembly industries. Though these processes are well known to the companies who do the recycling, few outside the industry including the generators of the by-products, understand the processes or needs of the industry. This paper will give a broad overview of these processes, and describe the services provided by this industry. The paper will also touch upon the future of the recycling industry, including the legislative and environmental push for the elimination of lead from electronics.

Jan 1, 2000

By Hong Yong Sohn

On the occasion of this symposium in my name, I reflect upon the contributions of my academic mentors and early associates who helped shape my professional career. I was fortunate to have these people around me during my graduate work and at the start of my professional career. In forming my view of the technical field and career, they represented academia, research institutions, industry, and different parts of the world.

Jan 1, 2006

By Linping Yu

A simplified ED process was developed for organic acids recovery from cyclohexanone waste in this paper. In this regard, the one-stage ED was investigated directly without pretreatment, such as ion-exchange or nanofiltration to removal of foulants. The current efficiency and the energy consumption in the ED process for the recovery of carboxylic acids from cyclohexanone waste is theoretically analyzed and experimentally tested. The concentration of recovered carboxylic acid is related to many parameters and still needs more work to be determined.

Jan 1, 2009

By Todd S. Fayram

The Gordonsville Operation of Pasminco US Inc. along with the Center for Advanced Mineral and Metallurgical Processing (CAMP) at Montana Tech studied, developed and implemented a pilot scale hydrometallurgical facility for the industrial recovery of germanium and gallium. This paper describes the joint testing and engineering program that culminated in this successful process.

Jan 1, 2003

By David M. Beckwith

Increased globalization and outsource manufacturing complicate the procurement and enforcement of intellectual property rights on a worldwide basis. Recent legislative and case law developments in the United States highlight the importance of a multinational intellectual property strategy. IP lawyers David Beckwith and John Hankins will discuss planning and pitfalls in this rapidly changing trans-border environment. Topics to be discussed include harmonization with international patent laws, protecting your technology and market space with a comprehensive approach to IP, and patent enforcement issues relating to import/export of products and components in the United States.

Jan 1, 2006

By H. Kurama

In this paper, utilization of fly ash as a value added product in areas such as novel materials, waste management, fillers and agriculture is reviewed with the aim of helping the expand of the usage of fly ash and reduce the environmental and economic impacts of disposal. The used unburned carbon benefication/treatment methods such as low temperature combustion, froth flotation, partical size classification and electrostatic separations to remove unburned carbon particles from fly ash are also discussed.

Jan 1, 2006