Search Documents

By Robert W. Bartlett

"Bioheap pretreatment of sulfidic refractory gold ore prior to cyanide leaching is a promising new technology, especially for low-grade ores that cannot afford to be oxidized by pressure leaching or roasting. When an ore contains both refractory and non-refractory (oxidized) gold, an economic decision must be made whether, or not, to pretreat before cyanide leaching. This choice is more complex than the familiar ore/waste cut-off grade decision. Pretreatment usually increases recovery but delays receiving revenue. Based on choosing the processing route that maximizes the present value of the ore, an equation is developed that computes a ""critical cyanide leachable gold grade"" for determining whether pretreating will be profitable. If the ore's actual cyanide leachable grade, without pretreatment, is above this ""critical grade,"" it will not pay to pretreat. The waste/ore cut-off grade, pretreatment yield (leachable grade after pretreatment), total gold grade, pretreatment operating cost and the project's financial discount rate are parameters in the equation. Results of example calculations are provided. This equation can be used for mine development planning and, when bioheap pretreatment is an available option, for daily operating decisions on individual ore blocks.IntroductionOres that are refractory because of sulfide mineral encapsulation of microscopic gold are becoming important. These ores must be pretreated to oxidize the sulfides to liberate the gold prior to cyanide leaching. The conventional pretreatment process technologies are pressure leaching with oxygen and two-stage fluid bed roasting. However, low-grade refractory ores cannot afford the high operating costs of these processes. And, small mines with limited reserves cannot justify the high capital costs of these processes."

Jan 1, 1997

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By J. Tang, B. Q. Li, R. Akarapu

"An integrated model is developed to represent the three-dimensional electromagnetic wave propagation and thermal phenomena during microwave heating of ceramics and dielectric/biological materials. The model development is based on the edge finite element formulation for electromagnetic fields and the node fmite element formulation for thermal phenomena. Results are presented and compared well with available analytical solutions and experimental measurements. With the model, the effect of sample positions on the electromagnetic and thermal field distributions is studied.IntroductionMicrowave, as an electro-heating source, has been widely used in the processing industries for packaged foods and other materials. The commonly used household microwave oven is a typical example of microwave heating processes. Other industrial microwave processing systems include large-scale microwave guides and cavities, which are used for the sintering operations as required for making ceramic components or for sterilizing the packaged foods."

Jan 1, 2004

By Geza Kisvarsanyi

Ore deposits composed of enargite, tennantite, gold, and pyrite have been mined in volcanic rocks of Oligocene age (35 m.y.) at Recsk, Hungary. Vertical and horizontal zoning of the alunitic-argillic alteration and of the ore minerals led to the concept of an intrusive heat source at depth. Subse-quent drilling disclosed a series of ore deposits in a zoned pattern in and around a stock, separated by a barren gap of 1000 meters from the shallow ore. The ore system is in a intracaldera horst-graben structure, formed by collapse and intrusion in a microplate subduction. volcanic-arc tectonic environment.

Jan 1, 1987

By Alireza Zakeri

To evaluate the behavior of minor elements in the copper smelting process, activities of silver, selenium and tellurium at minor concentration were determined at 1473 K within the miscibility gap of the Cu-S-Me (Me = Ag, Se, Te) and Cu-Fe-S-Me systems varied in Fe/Cu ratio. Phase relations between the immiscible metal and matte phases in the foregoing systems were first established by a quenching technique at 1473 K to supplement the activity measurement data. A Knudsen-effusion mass spectrometer, capable of handling complex gaseous systems and relatively small vapor pressures, was adopted for activity determination. Using a multiple Knudsen-cell, the ion intensity of minor element in the sample under study was measured simultaneously with that in a reference sample. Activity was obtained from the ratio between the measured ion intensities as well as the known activity value of the minor element in the reference sample. Limiting activity coefficients of the minor elements were correlated with composition of the matte. Based on the experimental results, the vaporization behavior of the minor elements has been discussed.

Jan 1, 1999

By Seyed Mohammad Taghavi

In this report, the efficacy of different factors such as temperature of reaction, time of reaction and depth of bed are investigated in a process of recovery of zinc oxide from zinc ore concentration residues in a fluidized bed furnace. Under optimum conditions, there was more than 93.5% zinc oxide in products.

Jan 1, 2006

By Ron Bernard

HW Process Technologies has successfully developed and commercialized various applications utilizing Engineered Membrane Separation (EMS?) systems for the processing of acidic copper hydrometallurgical solutions and wastewaters. Copper hydrometallurgical EMS? applications include water balance control and increased copper concentration in heap and dump copper leach operations, tankhouse bleed stream treatment to separate/recover copper and cobalt from iron, and removal of PLS/Electrolyte suspended solids/colloids to eliminate "crud" formation during copper SX/EW. Similar applications are underdevelopment to provide ionic separations in copper refinery bleed streams, copper smelter acid plant streams, as well as organic/LIX removal from aqueous electrolyte and raffinate streams. Copper mine wastewater EMS? applications include treatment of copper leach solution contaminated groundwaters for copper recovery and treatment of unwanted heap/dump drainage to provide enhanced precipitation, a smaller precipitation plant, improved operating costs and better quality discharge water, particularly in terms of TDS and sulfates. A discussion of the EMS? technology and general separation results on typical process solutions and wastewaters will be presented. HW Process Technologies, Inc. commercial installations treating copper pregnant solutions and leach solution contaminated groundwaters are in-place at an old Asarco smelter/refining operation, Mexicana de Cananea copper mine, and a major U.S. copper mine, with several additional installations pending. Several case studies, including results from a selection of these installations, will be included with detailed capital, operating cost, and system payback data.

Jan 1, 1999

By Cleusa Cristina Bueno Martha de Souza

Hydrometallurgical techniques for processing metals are becoming an efficient method for recovering metals. Although batteries' manufacturers have got rid of mercury content, some efforts have been made for recovering other metals enclosed in the battery formula. This paper discusses the bench scale experiments in the purification process of leached solutions from alkaline spent batteries. After leaching process using sulfuric acid as leachant, the solutions containing Fe, Cd, Pb, MIl, Zn and K were neutralized to precipitate iron hydroxide. In a second step, the purification experiments were carried out with excess of zinc dust to try to remove Cd while Mn and Zn still remain in the solution to be recovered in an electrolysis stage. The purification experiments procedures were conducted at different temperatures and times to find out properly conditions from the viewpoint of metals removal After filtration the solutions were submitted to chemical analysis to certify the metals content extracted.

Jan 1, 2001

By Patrick R. Taylor

A novel method for Chemical Vapor Infiltration (CVI) using plasma technology is proposed, Plasma Enhanced CVI (PE-CVI). Due to the low rates at which CVI is currently performed, the use of plasma as a source of heat may be considered to be a faster and less expensive production method. Precursors fed in the hot region of the plasma gas are completely vaporized and forced by the same flow through a porous preform where it condenses as a new material. In this research, silica and methane where used as precursors to form SiC/on a / graphite felt (preform). To enhance the infiltration process, vacuum was used to increase the flow through the preform. Characterization of infiltrated graphite was perfontied using Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD). A uniform distribution of Sic was observed along the felt with only twenty minutes of infiltration process, yielding a 178% increment in weight.

Jan 1, 1997

By A. V. Tarasov

One or more of the main alloying metals, i.e. copper, silicon, nickel, magnesium, zinc and other metals can form a composition with aluminum, by dissolving in the latter. The thermodynamic computations have indicated that within a range of temperatures from 700°C to 1300°C the reactions of molten aluminum with zinc and nickel oxides are shifted toward formation of free metals because it is possible to use the main alloying metals, i.e. zinc and nickel, in the form of inexpensive intermediate products and waste. The laboratory studies conducted have confirmed a possibility for production of aluminum alloys using intermediate products in the form of oxides of alloying metals.

Jan 1, 2006

By G. Azimi

Calcium sulphate precipitation, mainly as gypsum, during neutralization of acidic hydrometallurgical process solutions can lead to excessive scaling problems. In this work, a self-consistent fundamental chemical model is presented based on the OLI software platform. The model employs the new Mixed Solvent Electrolyte (MSE) activity coefficient model of OLI. A thermodynamic database has been developed and calibrated on experimental data from metal sulphate solutions. The model predicts very well the solubility of calcium sulphate within a wide temperature range and can be used to assess the scaling potential of a particular process stream composition. The effect of temperature, acidity, and divalent metal concentration on the solubility of calcium sulphate in multi-component process streams is also simulated and discussed.

Jan 1, 2006

By M. Giunti, R. Hampson, S. Gray, P. Kapoulitsas, J. Clark

In 1997 Pasminco's Port Pirie Lead Smelter began a modernisation of its lead and precious metals refinery operations. Driven by the anticipated closure of its Broken Hill mine, the new refining process replaced the locally developed continuous process, which had been in operation since the 1950's. Commissioning of the new plant was staged, beginning in late 1997, and finishing early in 1999. The new plant provides for batch refining of lead, and the use of vacuum induction retorting and bottom blown oxygen cupel technology in the silver refining area. The project has resulted in an increase of lead production capacity of 11% and allows the treatment of a wider range of concentrates than was formerly possible. The most significant change has been to double the smelter's silver capacity to over 400 tonnes per annum. This paper describes the successful implementation and optimisation of the new refinery, which is now consistently meeting design capacity.

Jan 1, 2000

By G. Cifuentes

When the applied current is interrupted in a copper electrowinning plant, and then is back in operation, the lead anodes tend to corrode. In order to decrease the corrosion, the damage protective ("back up") anodic currents are applied during the period of interruption. The current work aims to establish the effect of the concentrations of sulphuric acid, copper and cobalt on the anode corrosion, to quantify the effect of various anodic protection levels on the anode corrosion and to propose a method to select the appropriate protective current density value.

Jan 1, 1999

By V. M. Paretsky

Recent developments made in the Gintsvetmet Institute in the field of autogenous smelting processes have confirmed that autogenous smelting continues to be the main prospective technology for pyrometallurgical processing of sulfide raw materials. This technology ensures energy conservation and environmental safety conforming to the current world standards for production of heavy non-ferrous metals. Two alternative processes of single-stage autogenous smelting producing white metal as well as high-basic ferrite-calcium slags have been developed and can be recommended for technical modernization of Russian copper smelters.

Jan 1, 2002

By Ying-Chu Hoh

The extraction of cerium(IV) by valence change with two-phase electrolysis was studied experimentally. The results show that the electro-oxidation extraction depends mainly on the distribution of the solute between the two phases, the reaction on the electrode surface and the diffusion of the reactant and product between the electrode and aqueous interphases. The effects of various parameters on cerium extraction were also studied. The selected parameters were background current, catholyte acidity, agitation speed, operation current and voltage and surfactant addition. The electro-oxidation extraction mechanism can be divided into eight steps. In addition, Wee the rate of extraction is quite fast, the percentage extraction Ce+4 can be taken as an index to show the conversion rate of Ce+3 J to Ce+4.

Jan 1, 1989

By M. I. Kalashnikova

The leaching of metal nickel in copper sulfate solutions is investigated. It is established, that irre-spective of presence or absence of chloride-ion and oxidizer (oxygen) in system process can be divided into three stages, characterizing by restoration and oxidation of metals with formation of metal copper and cuprite and differing in the speeds of sedimentation of copper and transition of nickel into solution. At the initial stage of process along with allocation of metal copper it is be-sieged cuprite, that results in excess of speed of sedimentation of copper in comparison with dis-solution of nickel. At the second stage speed of transition of nickel into solution falls practically to zero, and sedimentation of copper proceeds on reaction of interaction of metal copper with copper sulfate solutions with cuprite formation. During the final period speed of transition of nickel into solution exceeds speed of sedimentation of copper due to course of reaction of resto-ration of cuprite up to metal. Influence of an ion of chloride and oxidizer on formation of various phases is revealed. It is established, that presence of an oxidizer results in increase in a share of cuprite in a deposit. With increase of the maintenance of chloride-ion speed of metal copper allo-cation essentially grows even at presence of an oxidizer in system.

Jan 1, 2006

By Klaus Gamweger

There are different reasons for purging a metal bath. The operations are varied, for example the purging gas can be used as a reactive gas being part of the metallurgical process or as an inert gas using the rising gas bubbles for agitation only. The different purposes for agitation, chemical and thermal homogenization or a preferential movement of the slag to the slag skimming door have to be considered. It depends on the furnace type and its dimensions as well as the process characteristics what the focus is on. For an optimized arrangement of numbers and position of all single plugs in the furnace, mathematical modeling - the CFD Computational Fluid Dynamics method - is used. This paper shows how the operation of purging plugs can influence the metallurgical process of an anode furnace by the example of Jinchuan Copper in China. The potentials for savings in energy consumption as well as in time for oxidation and reduction are presented.

Jan 1, 2006

By M. A. S. Siraa

A program of work was undertaken at the Kennecott Smelter and Refinery to model the complex. This effort contributed a total of eight models of the plant: flash smelting furnace, flash converting furnace, slag concentrator, anode furnace, offgas scrubbing system, acid plant, hydrometallurgical dust treatment plant, and the precious metals plant. Some of these models have been used in a variety of investigations ranging from offgas capacities for a steam generation analysis to an examination of impurities. The culmination of this enterprise has resulted in an on-line control scheme for the flash smelting and flash converting furnaces. These two process control schemes incorporate their respective steady-state heat and mass balances that are executed in response to feed changes while a feedback loop calculates when product grade and temperatures deviate from setpoints. This system has been put into place to improve furnace control and on- line time.

Jan 1, 1999

By Bruce W. Downing

MagPower has developed methods to control the detrimental formation of hydrogen that occurs in electrochemical reactions in numerous commercial applications such as the Magnesium-Air Fuel Cell, electrowinning, zinc alkaline batteries, hydrogen embrittlement, waste water/ metal recycling and coolants. The company?s approach to an alternative energy source is the development of an environmentally friendly non-toxic alternative power source that generates electricity through a combination of magnesium, oxygen and a saltwater electrolyte with MagPower?s patent pending hydrogen inhibitors. The magnesium-air technology has never reached the commercial stage due to its limiting power output caused by hydrogen generation. MagPowerhas solved this problem and has patents pending on its intellectual property; the Hydrogen Inhibitors and has developed several consumer power units for a variety of applications through licensing agreements. The company has also shown that the inhibitors have an impact on zinc electrowinning through laboratory test work where current efficiency was improved. This will significantly reduce power consumption and increase the efficiency of the electrowinning process, as well as reduce the potential acid mist hazards associated with electrowinning.

Jan 1, 2003

By K. B. Dotson

A common international safety and health management system was developed. Analysis of selected major safety and health management systems from around the world was conducted. Functional elements of selected systems were grouped to identify common elements and key differences. Common elements were subjected to qualitative judgments of equivalency and then reconciled. With few exceptions, differing elements were revised to achieve cultural neutrality. The resulting 98 system elements were organized according to the NOSA numbering and title scheme. System summaries were produced in Spanish and English. A pre-implementation self-assessment evaluated conformance in three distinct cultures. The consensus 98 element system was internally named the BHP Copper Five Star Safety System Performance Management Guidelines. Development of a common system within an organization with international operations can enhance the ability of the staff function to share resources, programs and subsystem improvements and thereby increasingly protect workers. Common systems can increase the level of management support by demonstrating increased compatibility of the safety and health management function with traditional business objectives. Safety professionals, industrial and occupational hygienists, business managers and the safety and health of workers will benefit from further development and articulation of common systems for safety and health management.

Jan 1, 1999