Search Documents

Acid generation from reactive sulphide mineral tailings has become a major environmental problem in the mining industry. Initiation of chemical and biochemical oxidation reactions of the sulphide mineral leads to acid generation. A novel concept of safe disposal and utilization of reactive fine mill tailings is presented in this paper. The paper also presents the results of a preliminary laboratory experimental .study of the concept. The tailings are agglomerated using portland cement as a binder. The cold bonded agglomerates are encapsulated with other chemical additives to act as acid neutralizers, oxygen and ironoxidizing bactericides., The primary. factors influencing the choice of bacterfoides to inhibit the acid generating bacteria are their costs, toxicity and environmental friendliness. The paper discusses the utilization of agglomerated' products as aggregates for underground backfill, or as gravel for surface land cover.

Jan 1, 1991

By André L. de Vegt

Soil and groundwater beneath a zinc production plant in The Netherlands are contaminated with metals and sulfate. To avoid contamination of nearby drinking water aquifers, a hydro-geological containment system and a biological treatment plant for the extracted ground water have been installed. Currently about 5000 m3/day of groundwater is extracted from a combination of 12 shallow and deep wells. Heavy metals and sulfate have to be removed from the extracted water before it can be discharged into a river. Several water treatment methods have been studied and pilot tested at the site. The preferred and selected process is based on the activity of sulfate reducing bacteria (SRB) and combines sulfate removal and heavy metal removal in one single installation. Anaerobic bacteria reduce sulfate to sulfide resulting in the precipitation of metal sulfides. Excess sulfide Is biologically converted to elemental sulfur. A full scale biological treatment system was started up in May 1992. Design, start-up, commissioning and operational experiences are reported in this paper. Concentrations of metals and sulfate in the SRB water treatment plant effluent are well within the limits set by the Dutch Authorities for discharge to surface water.

Jan 1, 1995

By Dan Michaelsen, Warwick Stewart

"PT Kaltim Prima Coal (KPC) is a large-scale truck and shovel operation mining thermal-coal in East Kalimantan, Indonesia. The operation produces 15 million tonnes of coal and mines over 120 million bank cubic metres of overburden annually. Approximately 35 percent of the waste rock is classified as potentially acid forming. Acid drainage must therefore be managed to prevent acid formation from spoil dumps and mined-out areas.KPC aims to prevent acid production in dumps by covering potentially acid forming spoils with materials identified as non acid-forming. The covers, built to engineering standards, minimise the flux of oxygen and water to pyritic spoils, thereby controlling the oxidation reaction, and reducing ARD discharge to negligible rates. Cover designs and cover materials vary according to stability, materials availability, equipment availability, and cost effectiveness. A modified field net acid generation (NAG) test procedure has been developed at KPC to identify and segregate overburden geochemical types. This paper discusses the ARD management strategies and operational procedures adopted by KPC to manage potentially acid forming waste rock. The development and field application of the NAG procedure at KPC is presented in a companion paper. Analytical"

Jan 1, 1999

By Peter Willbrandt

The flash smelter at NA was commissioned in March 1972 with an initial throughput of 50 tons of dry copper concentrate per hour. As a result of various measures, for example, oxygen enriched process wind, extension of the radiation part of the waste heat boiler, etc., the throughput could be increased to the present 70 tons per hour of dry concentrate. NA's plant is located on the outskirts of the city of Hamburg. The flash smelter's location and the growing awareness of the German population as regards environmental issues necessitate again and again considerable capital expenditure being spent on environmental protection. Thanks to the numerous small and large measures taken to protect the environment the emissions of dust, heavy metals such as arsenic, copper, lead, etc., and as well SO, could be drastically reduced. This paper will be giving an overview on the present state of the flash smelting process and the impact of the increasing environmental awareness at NA.

Jan 1, 1993

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. is carrying out a low cost production using a Tamano Type Flash Smelting Furnace (T-FSF), which is an improved version of Outokumpu Type Flash Smelting Furnace but without slag cleaning furnace and also by developing its own coke combustion technology. Coke combustion technology that is the basis of the system has been improved several times and, at present, it has evolved to a stage where it can be reproduced on the Computer guided system for Coke Combustion in the T-FSF (CCCT) using a general- purpose computer. This CCCT is featured by 'its trend control and predicting function, and an operator can freely control the operation parameters so as to control the operation flexibly. We have recently developed an overall energy reduction system covering the Smelting Plant to Sulfuric Acid Plant, which we call an Optimum Low Cost Operation System (OLCO) to reconsider the energy costs including coke, heavy fuel oil, and electric power. In this report, we would like to present the recent operation of T-FSF based on CCCT as well as the optimum energy operation utilizing OLCO system.

Jan 1, 2002

By Andrey Dmitriev

The solution of set of equations for the bottom zone presented by a condition of a thermodynamic equilibrium, namely, an equilibrium constant of wustite reduction by carbon oxide, material and thermal the balances, supplemented by the equation of the heat balance for the top zone, allows to calculate the base indices of blast furnace smelting. The calculated indices are extreme accessible at the given parameters of charge and blast. Application of actual degrees of the use of gas instead of equilibrium allows the calculations of actual indices of the blast furnace smelting process.

Jan 1, 2006

By Kwang-Ho Lee

The Onsan copper smelter of LS-Nikko Copper Inc. has operated the Mitsubishi continuous process along with Outokumpu process since 1997. Mitsubishi process is a bath smelting process which needs adequate melts for smelting reaction in the furnace. After a campaign shutdown it requires time to make a start melt. Onsan smelter has had much experience in flash smelting, including the improvement of the concentrate burner which is one of the most important parts in a flash smelting furnace. Based on this experience, the lances of the Mitsubishi smelting furnace were modified in order to making the starter melt with flash reaction. In 2004, the flash reaction in the Mitsubishi S-furnace was completed and was able to make the starter melt using these modified lances. Although at that time it was still under development it reduced the time required to make the initial bath-melt by about half.

Jan 1, 2006

By Lucas Lopes da Costa

Bamboo fibers were characterized in terms of diameter distribution and tensile properties. Polyester matrix composites reinforced with these fibers were investigated for their flexural mechanical behavior. Specimens with up to 30% in volume of continuous and aligned bamboo fiber composites were bend-tested until fracture. The results showed an improvement in the composite strength and stiffness with the amount of bamboo fiber. A microstructure analysis by scanning electron microscopy revealed a reasonable adhesion between the fiber and the polyester matrix which justifies the improved mechanical properties of the composites.

Jan 1, 2010

By Norbert L. Piret

During smelting of copper, arsenic in the feed reports to a large extent to the gas phase and some enters the anode copper. From the gas phase it is transferred during wet gas cleaning directly, or indirectly after dust processing, to aqueous solution. During the electrorefining and anode slimes processing, the anode arsenic content is also transferred to aqueous solution. Technology for the efficient removal of arsenic from process streams and cleaning of aqueous effluents is well established. However, the arsenic-bearing products, which thereby are generated, can vary widely in consistency, quality and quantity, from large amounts of gypsum contaminated with water-soluble arsenic compounds to residues with high arsenic content ' or arsenic products. Arsenic management in a copper smelter not only is involved with the duty of compliance to the gaseous and aqueous emissions standards but also should have as objective the minimization of the generation of arsenic-bearing and, in general, heavy metal-bearing solid waste. The present paper outlines options and the associated economic aspects for minimization of arsenic-bearing solid waste generation, for improvement of the environmental compatibility of the residues to be deposited and for the .production of commerciable arsenic compounds under appropriate market conditions.

Jan 1, 1999

By Dale T. Peters

In the United States, the United Kingdom and numerous other countries, copper has long been the plumbing material of choice. This has been the case since the late 1920s in the United States and since World War II in the United Kingdom. However, in recent years the plumbing tube market has caught the eye of the chemical industry, and several plastic resins have been introduced to the marketplace as substitutes for copper in household plumbing systems. One of these, polybutylene tube, had so many failures in the United States that a class action law suit was filed, and the manufactures of this product were forced to create a trust fund of nearly one billion dollars to repair damages caused by their product. Chlorinated polyvinylchloride (CPVC), in rigid pipe form, on the other hand, has been mechanically acceptable albeit its recent introduction precludes the test of time enjoyed by copper tube in this application. This paper reviews the State of California's portrayal of copper's environmental effects and will be largely based on the data and information assembled by the Copper Development Association Inc. in its presentation to the State of California in August, 1998 in response to the State's Draft Environmental Impact Report for Chlorinated Polyvinyl Chloride (CVPC) Pipe for Use for Potable Water Piping in Residential Buildings. The paper is intended for use as a model for the use of other copper organizations and individuals in responding to similar situations.

Jan 1, 1999

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By Lei Wang, Xiancong Zhao, Hongxu Li, Lifeng Zhang

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Jan 1, 2015

By Toshihiro Tanaka

The information on viscosity and surface tension of molten slag is indispensable to design new refining procedures in ferrous and non-ferrous processes. For example, the authors have tried to develop "Capillary Refining" to remove impurities in liquid metals by applying capillary absorption of molten slag with those impurities into solid fluxes which have a lot of small capillary tubes. It is necessary to adjust the above physico-chemical properties to adequate conditions on the capillary penetration. In the present paper, we discuss our recent trial to predict surface tension and viscosity of molten slag in multi-component systems. We have derived a thermodynamic model to predict the surface tension of molten slag by using ionic size, molar volume and surface tension of pure components. In addition, we have applied neural network computation to evaluate the viscosity of molten slag. We found good agreement of the calculated results with experimental values of the surface tension as well as the viscosity in various slag systems.

Jan 1, 2006

The entrainment of copper matte in the slag during the slag skimming stage of a Peirce-Smith converter was studied with a dam break model. Experiments were carried out with a range of fluid pairs where the lighter fluid was allowed to overflow a weir and the amount of entrained heavier fluid measured. The resulting entrainment is measured as the ratio of the heavy to light fluid withdrawn. The fluids include oil-water, water- glycerol and salt solutions-water pairs to cover a wide range of densities and viscosities. It was found that the Richardson number, Ri, correlates the entrainment well. For the case of the liquid-liquid interface initially at the same height as the weir, the entrainment was found to vary with Ri-1/3. The transient flow was simulated with a volume of fluid (VOF) code written in-house and used a stairstep approach to represent flow obstacles. The code was validated against the experimental results with good agreement for the variation of the heights of the two fluid with time. The simulation showed that the prevailing mechanism for entrainment is due to a pressure differential created across the liquid in the converter during pouring resulting in the heavier liquid being rotated upwards and over the weir.

Jan 1, 1999

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By Chuang Y-Y

A summary is made on the thermodynamic analysis for two of the four ternary systems of the quaternary Cu-Fe-Ni-S. The analysis is being extended to ternary Cu-Fe-S and then to the quaternary. An analysis is already made for the metal ternary but is not reported here. Experiment is being carried out to measure the liquidus surface. of Fe-Ni-S equilbrium with the fcc solid solutions of (Fe, Ni). The presentation at the Symposium will include all the results obtained at the time of presentation.

Jan 1, 1983

By Edgar Blanco

At the Deer Trail Mine, interest in recovering noble metals from oxide ore and tailings oxide ore with 6.0/1.0 g/t Au and 200/140 g/t Ag respectively has led to metallurgic studies focused on finding an adequate treatment for these materials. Using cyanide leaching, the silver/gold recoveries from oxide ore and oxide tailings were 39%/95% and 36%/96%, respectively. Since these recoveries were less than spectacular for silver, it was decided to explore a non-cyanide leaching process that would extract silver and gold better. Based on previous research the possibility of using aqua regia in combination with sulfuric acid was evaluated. On a laboratory scale, variables such as mineralogical composition, concentration of reagents, dissolved oxygen, reaction time, pH and temperature were evaluated. Under optimal conditions it was possible to achieve >65% silver recovery and >85% gold recovery for both oxide ore and tailings.

Jan 1, 2009

By Junji Shibata

Waste solution from the Ni non-electric plating process contains 4.0 kg/m3 Ni, 0.1 kglm3 Fe, 0.0 I kg/m3 Zn, 48 kg/m3 S042-, 98 kg/m3 HP032-and 31 kg/m3 laetic acid as a typical composition. Solvent extraction, cementation, ion exchange resin and precipitation methods are possible to use for the treatment of this kind of solution. In this study, solvent extraction of Ni was investigated using two kinds of extractants to clarify the relation between extraction percent and pH for various extractant mixtures. As Ni ion has an octahedral structure with ligands, the synergistic effect for Ni extraction is considered to take place in solvent extraction using two types of extractants. The investigation of the synergistic effect for Ni extraction was carried out in case of various extractant systems.

Jan 1, 2003

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By Guo Chen, Jin Chen, Jinhui Peng

In this paper, solving common problem of electrostatic precipitator (ESP), which was frequently ruptured of the cathode insulation in the production process were studied. The microwave heating airflow technology was introduced, which takes full advantage of its unique properties, solves the output problem of the high temperature air, achieves purpose of energy conservation, important economic significance and environmental significance. The mathematical models and designing of microwave high-temperature hot air system was calculated. The common forms of heat exchangers and comparative analysis were also introduced. The conditions found to be at the temperature of 240 °C. Under optimum conditions, the microwave heating power was 1482 W. Based on the mention results, this microwave heating method can be applied effectively and efficiently way for the production process of electrostatic precipitator.

Jan 1, 2015