Search Documents

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project's NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

By Kee Jeung Lee

In this study the characteristic factors and formation mechanisms for the hydrothermal preparation of a -quartz crystal powders were investigated to find the optimum synthetic conditions. The degree of Q -quartz crystal face development depended on the relative growth rate of a particular form that varies considerably with the degree of supersaturation, the reaction temperature, the concentration of mineralizers, and the presence of seed crystals in the feedstock. Alkali hydroxides and alkali halides were found to be effective in the reactions as mineralizers, which added in order to increase the solubility of the feedstock. The fine Q -quartz crystal powders were obtained in the temperature range of 250-450% and pressure range of 100-300atm. As the concentration of mineralizers increased, the particle size of crystalline powders became smaller at lower reaction temperatures. The fractional size distribution of synthetic crystal powders was depended on the hydrothermal conditions. As the reaction time and the amount of seed crystals increased, the width of particle size distribution became narrower. The weight mean particle size was in the range of 1 to 10m. The characterization of the products were carried out using XRD. SEM. PSA, FT-IR, Raman spectrometer.

Jan 1, 1997

The oxidation of ferrous ions by oxygen in sulphate solutions is a very slow process, but it tills long been known that the addition of sulphur dioxide increases the rate of reaction very significantly. The kinetics and mechanism of the process were investigated in the laboratory and the results confirmed the advantage of adding small amounts of sulphur dioxide to the oxygen stream for the removal of iron from solutions. The effect of various parameters on the overall rate of iron oxidation and precipitation was studied. In particular, temperature, acidity and composition of the gas mixture were considered and the optimum conditions for the precipitation of goethite were determined.

Jan 1, 1991

By A. E. Wraith

The tuyère flow rates of Peirce-Smith converters and bath smelting reactors are rendered particularly sensitive to accretion formation, bath depth variations and the general aerodynamic design of the blast delivery system by the limited pressure-flow properties of the conventional single stage centrifugal blower. This sensitivity is examined in terms of tuyère practice, vessel management and fixed engineering parameters for Peirce-Smith converters and the Noranda Reactor by use of the flow resistance factor, R*. New understanding of the effect of accretion growth on the flow behaviour of individual tuyères shows that blowing rates and hence throughputs could be optimised by careful attention to operating detail even within present plant constraints. The concept of the resistance vector is introduced to elucidate comparisons between different practices and to provide reference standards for optimisation. On this basis, the benefits of introducing quite moderate changes in the pressure-flow properties of the blast delivery system are considered. In view of recent developments in the flexible use of converters as hybrid bath smelting vessels for matte production, the foundation is now laid for a searching consideration of relationships between vessel volume and shape, blowing requirements, tuyère performance and production rates, the detail of which will be examined more appropriately in a forthcoming paper.

Jan 1, 1999

By John Sakala, Jeyapandian Sasikumar, Sydney Kwalela

The Isasmelt Furnace was commissioned in September 2006 with a concentrates treatment capacity of 850,000 tonnes per annum. However, the converter section became a bottleneck to the high throughput. Over 25% of the Isasmelt Furnace down time was attributed to lack of converter space. Factors that affected converter operations were low tuyere line campaign life (an average of 150 blows), high reverts generation, low conversion rates, and high converter cycle time. As a result of efforts carried out to improve converter operation, the average campaign life has increased to over 250 blows and reverts generation has been reduced from 22% of concentrate treated to 15%. Blister copper conversion rate has increased from 15 tonnes per hour to 19 tonnes per hour and blowing time per cycle has been reduced from 5.7 hours to 4.7 hours.

Jan 1, 2012

By Glenn C. Miller

Cyanide is the most common lixiviant for extraction of precious metals, and its efficient use in open pit mines has contributed to the increase in world production of gold during the previous two decades. With this expansion of precious metals mining using cyanide, public concerns have developed in response to the inherent public perception of cyanide as a tox-in as well as a series of environmental problems that are directly or indirectly related to cyanide use in open pit mining. Some of these have technical or regulatory solutions, while others will require additional investigation before they can be resolved. The following discussion will summarize some of the public concerns regarding the use of cyanide in precious metals mining. The issue of cyanide use in large scale precious mining is controversial, and recent banning of cyanide use in open pit mines in Montana, or complete banning of cyanide in Hungary has reflected those international concerns. The underlying basis for some of the bans (e.g. Montana) reflect a general concern of the environmental impacts of mining, rather than specific issues related to risk of cyanide use. The human safety record for cyanide use, particularly in the developed countries is good, and cyanide is clearly the most efficient lixiviant for precious metals. Indeed, the relatively short lifetime for cyanide in the environment renders it one of the less problematic chemicals used for extraction of gold from ore. Mercury amalgamation or use of bromide as a lixiviant are certainly much more problematic. What, then, is the basis f~r the international concern about precious metals mines that use cyanide. Ifuse of cyanide for gold recovery is to continue, what additional infom1ation needs to be developed that will allow a better management of the risks of cyanide? Which of the concerns are directly related to cyanide, and which are indirect concerns that more related to effects of open pit mining. Under what conditions should use of cyanide be discouraged? DUl::ing June of 2000 the United Nations Environmental Program conducted a two-day workshop on cyanide use in mining that was attended by persons from the mining industry, regulators and environmental community. Support and attendance at this workshop reflected concerns by all three groups on further restrictions for cyanide use and the emerging potential for guidelines for better management of the catastrophic release of cyanide-containing mining waste. The following discussion is meant to focus-on those risks and explore the basis for an often negative reaction to precious metals mining using cyanide. It is presented in the format of a statement, followed by a discussion. While admittedly provocative, the statements are meant to express the concerns? of the public regarding cyanide and the mining industry.

Jan 1, 1998

By Tingyao Liu, Lihui Han, Qing Liu, Bao Wang, Teng Yang, Yong Sheng

This paper mainly investigates the mass transfer phenomena of rare-earth concentrate from leaching process in Rushton stirred tank reactor with rotate speed of 100-600 rpm. In the research, a certain amount of sphere particles with 50-450 μm in diameter is treated as the mineral particles. Comparison of laboratory experiment data with numerical simulation is performed. The results show that the critical impeller speed for complete dispersion is 300 rpm. And the maximum value of turbulence kinetic energy appeared 15 mm away from paddle, where the mixing time is decreased 55% and 80%, respectively, when mineral particles are injected into stirred tank through one or four filling ports. Moreover, with mixing process going on, the numbers of particles near the paddle region accounts for as much as 58% of the total amount. Meanwhile, following the particle diameter increasing, the particle concentration of the upper part of stirred tank reactor is increased.

Jan 1, 2015

By T. Inami

The chlorine leach of the anode slime was studied in order to improve the treatment process at the Niihama Nickel Refinery. The anode slime originates from the nickel matte electrorefining and, contains 3-5% of nickel as sulfides. A comparative study has been conducted on the filter cake resulting from the sulfur filtration of the molten anode slime. The kinetic factors of the chlorine leach such as temperature, grain size were defined. Under the optimized condition, 70-80% of the nickel is recovered from the slime or filter cake. On the basis of these results, the chlorine leach process for the treatment of anode slime has been established. The leaching plant has been installed and successfully operated since 1986.

Jan 1, 1988

By Jack S. McPartland

Historically, research on thiosulfate leaching of precious metals ores has been focused on processing of difficult to treat ores. Thiosulfate leaching of ores and concentrates containing sulfide minerals, copper, manganese and preg-robbing carbon constituents has been evaluated. Cyanide leaching is generally considered an efficient, environmentally acceptable means for processing of non-refractory precious metal ores, Consequently, commercial processing of finely disseminated, oxidized precious metal ores is normally accomplished using alkaline cyanide leaching. Recent changes in regulatory climate have, however, called into question the acceptability of cyanide leaching in a number of locations worldwide. In some cases where the use of cyanide is being questioned, thiosulfate leaching may provide an acceptable alternative. Developments in thiosulfate leaching of precious metal ores are reviewed in this paper.

Jan 1, 1999

By C. H. Tsau

The intermetallic compounds of Ni-25Al-xFe, x is 20-40 at.%, were prepared by arc melting and drop casting into ingots, and were rapidly solidified into ribbons by melt spinning. The microstructure evolution of these alloys with varied Fe content were examined by the x-ray diffraction, optical microscope, scanning electron microscopy and transmission electron microscopy. The results reveal that two phases, {y'} and {B} phases, are existing in the alloys with low Fe content, and the microstructure changes from the mixture of y' and {B} phases to a single 0' phase when the Fe-content reaches to 40 at.%. Also, the formation of y' phase will be suppressed by rapidly solidified process. For annealing both of the melt-spun and the cast specimens, a disorder 0 phase was revealed in both of the ribbon and the cast ingot of Ni-Al-Fe alloys with higher Fe content. In addition, increasing the increment of iron which substituting nickel in this alloys results in increasing the lattice parameter of both {y'} and{B} phases.

Jan 1, 1992

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By K. Soldenhoff

The Bulong deposit, situated near Kalgoorlie in Western Australia and owned by Resolute Limited, is a lateritic deposit containing on average 1.1% nickel and 0.09% cobalt. A process has been developed and tested at the mini-plant scale for direct solvent extraction and separation of Co and Ni from solutions derived by acid pressure leaching of Bulong ore. In this paper, two solvent extraction processes are described. The first process uses Cyanex 272 to extract cobalt and reject nickel to the raffinate. The second process uses Versatic 10 to extract and purify nickel. The loaded strip nickel solution is suitable for electrowinning. Results of both batch laboratory tests and continuous mini-plant trials are presented. The selectivity of the solvents with respect to the major impurities such as Mn, Mg, Ca, and Zn is also discussed.

Jan 1, 1998

The generation of acid mine water is? due to the oxidation and weathering of sulfide bearing tailings and overburdens. Ferrite precipitation prooess has been applied to treat acid mine water. The conventional ferrite preC1pitatlon requires air oxidation at high temperature, or long aging time or addition of magnetite powder ,as promoter. In this investigation, a modified ferrite, precipitation process is developed by which magnetic ferrite can be produced at an ambient temperature. Acid mine waters from Berkeley Pit (Montana, U. S. A.) and from Noranda Tailings (Quebec, Canada) were used. The co precipitation of heavy metals from these two acid mine waters is studied as a function of FeIM molar ratio, oxidation time and settling rate under applied magnetic field. The investigation indicates that the modified ferrite co precipitation can remove substantially all of the, dissolved metal ions from acid mine water. The ferrite product obtained after precipitation' is characterized by XRD, SEM, BET and saturation magnetization. The results show that spinel ferrite, precipitation can be achieved at room temperature and the saturation magnetization of ferrite product from,acid mine water is comparable to that of pure ferrites.

Jan 1, 1995

By W. Zhao

Several years ago, Reddy and Blander presented upriori model for calculating the sulfide capacity of binary silicate melts. It is modified now to apply to CaO-AlO 1.5 melts at different temperatures and compositions. Our predictions are in very good agreement with the available experimental data. From a comparison of binary calcium aluminate and calcium silicate systems, higher sulfide capacities are obtained in aluminate systems. The sulfur can be removed from hot metal more effectively by adding aluminate melts.

Jan 1, 1995

By K. Dzieciol

The paper presents a study about three image correlation methods ?common cross-correlation, mutual information and phase-correlation ? applied to characterize microstructures reconstructed with X-ray tomography. It is shown that phase correlation is not only the fastest, but also the most sensitive method for detection of similar microstructure features, cavities in the present case. A new image correlation indicator is proposed, which takes into account both the phase shift and the amplitude of similar features in compared images. Some preprocessing aspects related to the tomographic reconstruction and filtering out of characteristic noise are also discussed.

Jan 1, 2009

By Uday B. Pal

In the electrochemical vapor deposition (EVD) process, gaseous cation precursors are passed over one side of a porous substrate, and oxygen is passed on the other side of the substrate. The gases diffuse and react within the porous substrate, and the pores get filled with the desired solid oxide. Subsequent solid state electrochemical transport through the solid oxide in the pores continues the reaction, and the film grows over the porous substrate. The EVD process has been used to deposit lanthanum chromite interconnection films and yttria stabilized zirconia electrolyte films over porous air electrodes. The EVD growth of these solid oxide films is found to be parabolic in nature, which indicates that the solid state transport (diffusion) of ions through the film controls the growth. This solid state transport can be analyzed using Wagner's treatment of the electrochemical transport. Conductivity measurements and the information on the defect structure of the oxide can be combined with the EVD growth rate measurements to calculate the solid state transport properties (transport numbers and partial conductivities) of the rate-controlling minority species in the oxide. Using this approach, the EVD growth of other electronic, mixed conducting and ionic solid oxide films can also be analyzed.

Jan 1, 1992

By Kenneth G. Thomas

This paper reviews the alkaline and acid gold autoclaving experiences gained at Barrick Gold Corporation. Alkaline autoclaving was operational at Barrick Mercur, Utah, U.S.A., on carbonaceous/sulphide refractory ore for eight years commencing in 1988. Acid autoclaves have been operational at Barrick Goldstrike, Nevada, U.S.A., on sulphide refractory ore since 1990 and now process 17,500 stpd of ore through six large autoclaves. Information is presented on operating costs, materials of construction, reagent requirements and flow sheet developments that reduced capital and operating costs.

Jan 1, 2000

By C. Segawa

SMM operates an original slime treatment process for recovering precious metals and other metals (Te,Se,Sb,Bi)from the copper and the lead anode tankhouse slimes. In recent years, the amount of slimes has increased and the pyrometallurgical processing units capacity became the bottleneck of the entire plants. For the expansion of the plant, new pyrometallurgical facilities, incorporating a BBOC, was commissioned in 1992 and has now been successfully operated. In addition, unit operations were optimized to increase recovery and reduce operating cost .. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1996

By Xinghui Meng

The recovery of platinum and palladium from automotive catalysts has been investigated by leaching in iodide solutions with oxidants including oxygen and iodine in an autoclave. An ammonium salt was presented in a neutral leaching solution as a key leaching reagent to achieve high recoveries of the platinum group metals (PGM). The effect of temperature, and concentrations of oxidants and of ammonium salt on the recovery of PGM was examined. Under the experimental conditions studied, the recovery of platinum and palladium was found to be greater than 95%. An economical assessment of this process has also been examined and discussed.

Jan 1, 1995

By T. Shibasaki

There is a strong demand in the photo industry to the higher quality of refined silver. Osaka Refinery produces about 27 mtpm of refined silver mainly from copper refinery slimes. Product quality is attained by controlling the impurity level in electrolyte. Copper is cemented with silver oxide and palladium is precipitated by a chelating agent. Both processes were operated previously in batchwise for treatment of bled out electrolyte, Recently these processes have been improved and made continuous to cope with the increased impurity.load. As a result the grade of fine silver has been maintained steadily at Pd < 3 ppm and Cu < 5 ppm.

Jan 1, 1989