Search Documents

By Evan Jamieson

The conditions under which various iron(III) oxy-hydroxides phases precipitate from iron(III) chloride and sulfate solutions at ambient temperatures (<60°C) are reviewed. Many of these precipitates are slow settling and gelatinous but ultimately transform into other more stable or crystalline phases. The phase that forms depends upon the rate of precipitation and pH. A comparison has been made of the iron(III) oxides formed upon the neutralisation of various iron(III) solutions with caustic, slaked lime or slaked magnesia which provide different rates of neutralisation and slowly dissolving solids with localised high pH. Mössbauer spectra of ferrihydrites precipitated under these different conditions are compared and interpreted. Particular attention is paid to the settling rate and settled volume which is likely to relate to industrial thickener and filter performance. It is shown that in pure chloride solutions, poorly settling ferrihydrite is usually produced at 20oC regardless of the choice of base. However in sulfate solutions fast settling precipitates are produced using lime and magnesia but not with caustic. In mixed chloride/sulfate solutions, optimum settling rates occur when the molar ratio of [SO4]2to Fe3+ is about 1:1 and when the sulfate concentration is <0.20 M. It is proposed that ?dense amorphous basic iron sulfate? or well-ordered ferrihydrite is formed on slowly dissolving lime or magnesia surfaces. Implications for industrial liquors are considered.

Jan 1, 2003

By Peter Koh

The velocity solid charge attains when dropping down concentrate chutes is an important boundary condition when developing mathematical models of flash furnace burners and reaction shafts. In this work an experimental rig was developed to measure the velocity attained when nickel concentrate and sand were dropped down a vertical pipe 3m long. The velocity measurements showed that the nickel concentrate did not fall as individual particles. The measured values of the velocity approached, but did not attain, those calculated for solid bodies, the disparity being attributed to friction at the pipe wall and fluid drag losses. After falling 2 m velocities between 5-6 m/s were attained. The analysis was extended and applied to understanding the intermittent problem of puffing which sometimes occurs from the top of the concentrate chute. The pressure at the bottom of the chute is the net result of two opposing pressures, namely that developed by (a)the process air entering through the velocity control device, and (b) the solids falling down the concentrate chute. Flow back up the chute occurs when the former exceeds the latter. The process air pressures in the burner were obtained from CFD simulations of a full burner. Variables considered included air speed through the velocity control device, drop height and furnace draft. The analysis was useful in highlighting the operating conditions which were conducive to puffing and in establishing procedures to minimise its occurrence.

Jan 1, 2006

By M. Cross, K. Pericleous, A. Mouchmov

"Copper - nickel - sulphide alloys are typically cooled and solidified in 4, 8 and 16 tonne ingots. These ingots exhibit a variation of grain size distribution and macro segregation of the prime alloy components throughout. The former is assumed to be primarily due to the dominant relation between grain growth rate and the cooling profile, whilst the latter is heavily influenced by buoyancy driven residual convection. The objective of this research program is to examine the extent to which it is possible to develop a 'broad brush' computational model of this ingot cooling process, that can predict some 'integral' measure of the grain size (e.g. average diameter) and the macro-segregation as a function of operating conditions.A computational modeling software framework, PHYSICA+ is used to simulate the complex process of ingot casting, which involves coupling between different physical phenomena. The entire model involves:(i) a 'broad brush' grain growth model that could be used in the prediction of micro/macro-structure of alloy ingot cooling processes,(ii) a heat transfer and solidification model which takes into account a second phase transformation of P NhS2 to heazlewoodite, and (iii) NS fluid flow simulation which provides a good basis for further micro/macro segregation modeling.At this stage some results of the 3D convection driven thermal cooling and solidification profiles will be shown, together with the 'integral' model for the grain size prediction."

Jan 1, 2001

By Matsufumi Takaya, Yukihiro Sakamoto

"Electric field emission properties from CVD diamond fabricated using pulse-modulated microwave plasma CVD were studied. Diamond was synthesized by microwave plasma CVD apparatus equipped with a pulse-modulated microwave power supply. Pulse conditions were varied from 1 to 10 seconds for pulse periods and from 0.1 to lHz for pulse frequency either. Surface morphologies of the deposits were differed by pulse frequency and duty cycle. As a result, FE properties prepared by different pulse duty cycle were different from continuous film which synthesized using continuous microwave significantly. Highest current density was obtained from the uneven morphology diamond film prepared at 17.5% pulse duty cycle.FE properties of the CVD diamond were depended on surface morphologies that related to the pulse conditions.1. IntroductionDiamond has excellent physical and chemical properties as an industrial material. Especially, hydrogen terminated diamond had the negative electron affinity (NEA) 1) and CVD diamond has this NEA property either as deposited 2). So the electron emission source to the FED is expected as one of this application of CVD diamond as cold cathode of electric devices. We studied on FE properties of various CVD diamond, pulse microwave plasma CVD diamond showed better property than those of other CVD diamond 3).This report studied on· the effect of the duty-cycle of pulse modulate microwave condition on FE properties of the diamond fabricated by pulse modulated microwave plasma CVD."

Jan 1, 2000

By Rong Yang, Qijie Zhai, Wenbin Xia, Changjiang Song

"Tills paper focus on the influence of carbon content and cooling rate on the microstructure and phase formation of Fe-Mn-C alloys under near-rapid solidification. When manganese content is about 11wt.%, more s-martensite can be obtained with cooling rate increasing when carbon content is 0.14wt.%, the formed phase changed from a phase to y phase when 0.74wt.% carbon is added to the samples, and when carbon content up to 2.1wt.%, carbide can be obtained in the sample. A host of stacking fault, which attributes to the strain-induced martensite, can be observed in the sample. The microhardness increased with cooling rate increasing, and under the same cooling rate, the microhardness of samples with 0.14wt.% carbon is highest.IntroductionTo obtain high performance materials is eternal pursuit of material science research. Material scientists have explored many new ways to obtain high performance materials from long time ago. Rapid solidification is one of most popular ways to produce advanced materials by obtaining metastable phases, because it is widely known that the solidification of metals in metastable phases gives access to a whole range of materials with novel properties [1]. Furthermore, nowadays metastable materials have been extensively used in many fields, for example, many of our modem high performance materials such as steel products or aluminum alloys for aeronautical applications are in the form of metastable rather than stable phases [1]."

Jan 1, 2012

By V. Tsukerman, Ivanovam L.

"The potential of hydrocarbon resources in the Arctic oil and gas provinces is enormous. Oil, gas and condensate constitute the basis of mineral resource base of the shelf zone of the Russian Arctic; summary volume of hydrocarbons exceeds 100 billion tons of conventional fuel. Only in the Shtockman gas condensate field in the Barents Sea explored balance reserves equal to 3.2 trillion m3 of gas. It is necessary to establish a special regime of nature management in the Arctic. Environmentally oriented economic activities should be more actively stimulated. The Energy Strategy plans that starting from 2010 in the Barents and Pechora Seas up to 10 million tons of oil and 50 billion m3 of gas will be extracted, reaching the level of 30 million tons of oil and 130 billion m3 of gas in 2020. This task cannot be solved without intensification of geological exploration on the continental shelf. IntroductionThe elaborated strategy of mining enterprises should correspond to the modern paradigm of mining industry development which is not only for extraction of minerals but also for multi-profile structure having comprehensive use of the resources on the rational basis intended for rational complex utilization of mineral resources of the Arctic zone of Russia which by the definition includes maximally full use of the whole aggregate of resources on the economically rational basis with obligatory environmental with resource reproductive and socio-economic functions and deterrents"

Jan 1, 2008

By Yongxiang Yang

High temperature processing of raw materials in metals production and recycling often involves complex multi-phase fluid flow and heterogeneous chemical reactions at various scales. Good understanding of the process physics and chemistry is crucial for process operation and process development. The traditional scale-up process through laboratory scale ? pilot scale ? commercial scale route has been more and more complemented and partially replaced by full-scale process simulation. Computational fluid dynamics (CFD) has become a very useful simulation tool in process research and development. At the same time industrial applications challenge the CFD development with its complex transport phenomena, often in large-scale reactors with small-scale physics and chemistry. The current paper discusses the applications of CFD to a number of high temperature metallurgical and materials processing applications. The research was carried out by using commercial CFD codes as the framework, and the emphasis was given to the special efforts for the development and implementations of sub-models with process-dependent physical and chemical characteristics. To illustrate the application of CFD simulation to high temperature metallurgical processes and coupling of sub-models to the general-purpose CFD codes, five examples are given: (1) melting of aluminium scrap in a rotary furnace for recycling, (2) molten hot metal flow in a heterogeneous coke-bed of a blast furnace hearth, (3) gas flow heat and mass transfer in a submerge electric arc furnace for phosphorus production, (4) high temperature incineration of hazardous waste in a rotary kiln, and (5) transient heating of metals in heat treatment furnaces.

Jan 1, 2006

By S. B. Breyner, A. Ressler, D. Gregurek, A. Spanring

"The changes in process conditions that frequently decrease the service life of refractory products provided incentive for RHI AG to develop high performance bricks, especially for non-ferrous metal applications. Innovative product development was required to determine suitable refractory products for improving lining life. At the Technology Center in Leoben, Austria, practical corrosion testing methods and facilities, including an induction furnace and rotary kiln, enable detailed comparative analysis of brick wear on a pilot scale. In tests that were carried out using a fayalite type slag, the newly developed RADEX VFG magnesia-chromite grade showed very promising results compared to the standard grades. Based on the test results, optimal refractory solutions can be recommended for this challenging industrial application and field trials can be performed directly at the customer's site.IntroductionThe complexity of metallurgical processes in the non-ferrous metal industry, and especially changes to the process conditions in combination with the diversity of metal processing furnaces ''', requires a precise understanding of each individual system for appropriate refractory product selection l2'. In addition, particular importance is focused on the specific refractory consumption being as low as possible.Another important aspect results from the global shortage of resources, which forces companies to invest in recycling processes. In the base metal industry, recycling operations have resulted in significant changes; for example, operating with two slag chemistries and process temperatures will influence the performance of previously suitable linings. The raw material mix for primary smelters has also changed, including higher levels of secondary raw materials in the smelter feed."

Jan 1, 2012

By Michael Stelter

Lead alloys are a typical material for anodes in technical electrowinning processes. The life time of those anodes differs from 2 years to more than 5 years in tankhouse practice depending on the type of alloy, the mechanical damaging and last but not least the chemical corrosion in the electrolyte. Different types of alloys, such as PbSb, PbCa, PbAg, PbSnCa or PbAgCa have been developed and used in the past, their rate of corrosion being more or less a philosophic discussion. Comparable investigations on the corrosion behavior in dependence of the concentrations of alloying metals, the grain structure and the mechanical and thermal treatment during production have not been conducted before. In the last years the Institute for Nonferrous Metallurgy and Purest Materials of the TU Bergakademie Freiberg investigated the corrosion behavior of the typical lead alloys for metal electrowinning under comparable conditions. Correlations between different alloys, mechanical treatments like rolling or thermal treatment like annealing to the rate of corrosion were made, leading to the conclusion that grain structure and grain size are of eminent importance for the rate of corrosion in technical electrolytes. From these results new and optimized lead alloy anodes can be produced with an increase in life time of the factor 3 ? 5. The optimized lifetime in terms of corrosion stability can not protect from mechanical damaging in tankhouse practice, but with a careful practice the increase in lifetime can save a lot of money and problems.

Jan 1, 2006

By R. Mehta, M. Misra, X. Su

"The conventional methods to assess Acid Mine Drainage (AMD) potential of the waste rocks and tailings are based on wet chemistry and leachability tests. These methods are time consuming and expensive. There is a growing interest to develop alternate techniques to establish the reactivity of acid mine tailings and stability of treated waste forms. The Electrochemical Impedance Spectroscopy (EIS) is a reliable non-invasive technique which can be used for quick estimation of reactivity of the potential acid generating tailings. In this paper the utilization of the EIS technique for the estimation of reactivity of tailings is discussed. EIS can also be used to predict the long term stability of different stabilized waste forms.IntroductionMetal contaminated mine drainage is one of the most persistent environmental problems facing the mining and mineral processing industries today. Of all the mine drainage pollutants, acid mine drainage has become a substantial concern because of the potential long-term environmental implications and the accompanying liabilities. The main source of acid mine drainage is the tailings containing sulfide-ores which are generated during the ore processing. When these sulfide minerals, particularly pyrite and pyrrhotite, are exposed to oxygen and water they begin to oxidize. The initial chemical reactions produce acid and the acid dissolves heavy metals present in the tailings. Rainfall and snow-melt flush the toxic solutions from the waste sites into the downstream environment [1-2]. In addition to mining tailings, several Department of Energy (DOE) sites contain wastes which are contaminated with radionuclides and heavy metals."

Jan 1, 1999

By Truan-Sheng Lui, Li-Hui Chen, Hao-Wen Hsueh, Fei-Yi Hung

"Since Ag wires have similar hardness and bonding properties to Au wires, they can be applied in some pads. In the present study, the annealing effect (at 225°C~275°C for 30min) on the tensile mechanical properties of silver wires with f=23µm was investigated. In addition, the micro-structural characteristics and the mechanical properties before and after an electric flame-off (EFO) process were also studied. Experimental results indicate that with annealing temperatures of more than 250°C, the silver wires possessed a fully annealed structure, the tensile strength and the hardness decreased, and the elongation was raised significantly. Under the thermal effect of EFO, the necks of the Ag balls underwent recrystallization and grain growth was induced, and the annealed Ag wires had a shorter zone of HAZ (220µm). The bonding strength and the neck-strength of the Ag wires were more than 7gf and possessed excellent bonding properties.IntroductionThermosonic ball bonding is one of the preferred processes for electronic packaging to connect a semiconductor chip and a lead frame by a thin metal wire. At present, gold wire and copper wire are the preferred interconnect materials to bond with the aluminum metallized wafer pads [1, 2]. Since gold is expensive and the reliability of copper is poorer [3], the study of silver wire has attracted a lot of attention already. In addition, the inherent properties of high ductility and low hardness of silver as well as its workability effectiveness compared to gold, have made it a preferred alternative .[4, 5]"

Jan 1, 2012

By Qin Hua, Xiangru Chen, Qijie Zhai, Yongsheng Yan, Liang Chang

"In this paper, pure bainite ductile iron and their alloying form of 0.2wt% niobium were prepared by a controlled cooling heat-treatment. The effect of niobium alloying on the microstructure, hardness and impact toughness of bainite ductile iron was studied. The results show that adding niobium effectively improves the hardness and toughness of bainite ductile iron. The hardness and the impact toughness of niobium-alloyed bainite ductile iron were investigated by varying the temperature at which samples were fed to the incubator.IntroductionThere are two essential methods to prepare the bainite ductile iron: isothermal quenching [I-31, and alloying [4• 51• Isothermal quenching process is very time and energy consumable, concerned as a high cost technique for mass production. Besides, there are certain limitations on the size and shape of castings in this process. In addition, it potentially harms the environment. As for the alloying, Ni, Mo, and Cu have to be utilized to obtain bainite. However, the large demand and high cost of Ni makes it not feasible in practice.It is well known that niobium can promote the formation of carbon compound, and improves the stability ofundercooled austenite, which is preferred to the increase of the hardenability. Previous studies showed that niobium could refine the grain and improve the mechanical properties of gray cast iron [6-81 • Therefore, in the present work, the effects of niobium and the temperature at which samples were fed to the incubator on the microstructures and properties of niobium alloyed bainite ductile iron were investigated."

Jan 1, 2014

By Mariola Saternus

The quality of the liquid metal has the biggest influence on the quality of the final products. In the metallurgical industry, and especially in aluminium production the refining process is the important technological stage. Today the most popular are refining reactors with impellers like URO ? 200, which can generate small gas bubbles. A rotary impeller also makes the metal bath to be stirred well. There are two basic hydrodynamic parameters: the flow rate of refining gas and the mixing of refining gas (impeller rotation) that influence metal stirring and generating small gas bubbles. The paper presents the influence of the flow rate of refining gas on the hydrogen removal process from aluminium (final hydrogen concentration), taking into consideration the refining process of AlSi7Mg alloy and using URO - 200. The mathematical model of this process is also presented. The equation needed for calculation of the final hydrogen concentration as a function of the equivalent bubble diameter is shown. Basing on this equation the calculations of bubble diameter and optimal refining time are done. This paper presents the physical model (the water one) of aluminium refining process and the gas dispersion taking into account the fact that the gas flow rate is changing from 2,5 to 17,5 l/min and the impeller speed is changing from 0 to 400 rpm. Schemes of gas dispersion in liquid metal in comparison with the model data are shown and the optimal values of the gas flow rate and the impeller speed are chosen.

Jan 1, 2006

By Kimio Itagaki

Thermodynamics and rate process fundamentals are two of the important principles involved in nonferrous production processes. The process configuration establishes whether thermodynamics or rate process behavior is most relevant in a particular application. In this paper, thermodynamic theory and rate process fundamentals are used to analyze the main characteristics of smelting and converting processes. The effect of increased oxygen potential .is examined with emphasis in view of the increased use of highly oxygen-enriched gas in modem smelting processes. Phase equilibrium and the distribution of minor elements between copper or nickel matte and FeOx-SO2- or FeOx-CaO-based slag are reviewed. The use of oxygen-rich gas has no serious effects on &apos;the recovery of valuable copper and silver in the matte phase, while the recovery of nickel and cobalt is adversely affected. The oxygen content in the gas also strongly affects the distribution behavior of arsenic, antimony and bismuth. Analysis of the rate processes occurring in the shaft of flash smelting, and converting furnaces by a 3-D computational fluid-dynamics model is also discussed. After being validated with experimental data collected in a large laboratory furnace, the computer model has been used to simulate the main features of an industrial flash converting operation. The results present quantitative features of the improved mixing of the particle-gas suspension and increased oxygen efficiency obtained with a distributor-cone burner compared with those with a single axial entry burner. The role of basic principles in the engineering analysis of high-intensity matte smelting processes is also discussed.

Jan 1, 2002

By K. Asokan, K. Subramanian

"Electrowinning of copper by monopolar cells require common anode and cathode busbar and crossbars to connect each electrode to the respective common busbar. On the other hand, the bipolar configuration warrants the end electrodes only to be connected to busbars; there is substantial reduction in copper requirement. In the present work, an electrowinning cell with bipolar electrodes and end electrodes, each having an area of 1000 cm2 was designed and operated. The bipolar electrode is made of mixed metal oxide coated titanium mesh welded to plain titanium sheet. Coated titanium mesh acts as anode and the plain titanium sheet acts as cathode. Environmentally unacceptable lead anode and the recurring loss of lead are done away with. Closer spacing of the electrodes, paves way for the application of higher current density leading to mass transfer enhancement. Performance of bipolar copper electrowinning cell is reported.1. IntroductionThe normally adopted practice in electrowinning of copper is the conventional monopolar configuration. In this practice, the individual electrodes act either as anode or cathode. Hence there is a need to connect every one of the electrodes to the common anode or cathode busbar and crossbars running across the top of the cell are necessary. The common busbar carries very high current which is divided among the individual crossbars and hence has to be thicker in relation to the current load of the cell. The drawback of the need to use common busbars of thicker cross section and the need to have crossbars are obviated in the bipolar configuration."

Jan 1, 2009

By V. Bojarevics, K. Pericleous

"A number of different methods have been developed for noncontact electromagnetic treatment of liquid metal and to investigate the melting/solidification processes. Applying AC magnetic field in terrestrial conditions, along with the buoyancy and thermo-capillary forces, results in turbulent flow. The use of a homogenous DC magnetic field allows damping both of the turbulence and the large scale flow at different rates leading to surprising results at some stages. The dynamic interaction of the turbulent flow with the oscillating interface needs to be accounted if it is required to levitate liquid metal of up to few kilograms without the contact to container walls. At the high values of magnetic field some oscillation modes are damped quickly, while others are modified with a considerable shift of the oscillating droplet frequencies and the damping constants from the non-magnetic case. Numerical models are used to investigate behavior of liquid metal suspended in high DC magnetic fields providing microgravity-like conditions with laminar viscosity and heat transfer to the surroundings.IntroductionSince the early Electro Magnetic (EM) levitation experiments [1] in AC magnetic field it became apparent that the levitated liquid metal is prone to oscillation and instability. The EM and electrostatic levitation experiments with liquid metal droplets show difficulties related to confinement stability and a need for complex correction functions to establish a correlation between the measurements and the droplet material properties [2,3]. Intense internal fluid flow is visually observed, apparently being in the turbulent regime for earthbound conditions."

Jan 1, 2012

By Alim Ullah

Process, quality and management control are necessary in order to produce DRI of required quality and at minimum cost. Although the characteristics of the two (2) principal inputs, that is, iron oxide feed and natural gas (for gas-based DRI plants) can affect the operation of a DRI plant significantly, they are outside the control of plant operators, at least in the short run. The quantity of reduction gas, its composition and reduction gas temperature are some of the key process variables. Statistical Process Control (SPC) can be used in a DRI plant to minimize the production of off-grade material and costs, as well as to improve the overall operation of the plant. One of the key quality variables to be measured and controlled is percent metallization, defined as FeM/FeT*100 where, FeM and FeT respectively are metallic iron and total iron in DRI. Control charts are used to monitor the quality of DRI produced and, when necessary, corrective actions are taken to bring the product back within the control limits. Management control can consist of essentially following how well the plant performs against some pre-established standards of parameters like daily production, downtime, consumption of material and energy, etc. In this respect, it is suggested that yield, defined as theoretical consumption/actual consumption of iron oxide feed, be used to monitor the consumption of feed material. Similarly, instead of using natural gas per ton of DRI produced, a better criterion would be efficiency, defined as theoretical natural gas consumption/actual natural gas consumption.

Jan 1, 2006

By Pradeep kumar Jha, Manas Mohan Mahapatra, Sabin Kumar Mishra, Satish Kumar Ajmani, Satish C. Sharma

"Due to mechanical/ electrical failure in the C.C. line or inadequate availability of molten steel from coming ladle, sometimes one/two outlets of a multi-strand tundish in continuous casting unit is closed. Closing any of the outlets affects the flow distribution inside the tundish which in turn governs the quality of steel coming out. Hence it is important to study which of the outlets should be closed to have proper results in terms of flow behavior and inclusion removal inside the tundish. Present study aims at finding the effect of closing one or two outlets on flow behavior and inclusion removal in a multi strand tundish. It was found that closing the near outlet (outlet near to the inlet) increases the inclusion removal tendency than closing the other two outlets in a six-strand billet caster tundish (only three outlets are considered because of symmetry).IntroductionContinuous casting process transforms molten metal into solid on a continuous basis. This process is the most efficient way to solidify large volumes of metal into simple shapes for subsequent processing [1]. Molten metal is tapped into the ladle from furnaces. From the ladle, the hot metal is transferred via a refractory shroud (pipe) to a holding bath called a tundish. The tundish allows a reservoir of metal to feed the casting machine while ladles are switched, thus acting as a buffer of hot metal as well as smoothing out flow, regulating metal feed to the moulds and cleaning the metal [2]."

Jan 1, 2012

By A. Siegmund, R. D. Prengaman

Lead anodes used in zinc electrowinning generally contain 0.5 - 1.0 % silver to reduce the rate of corrosion over the service life. For good quality zinc, the cathodes must contain less than 10 ppm lead. In order to reduce the lead contamination of the cathode, the lead anode must become coated with a protective layer of Pb02/Mn02. The formation of this layer may take as long as 30 - 60 days, during which time zinc production is substantially reduced and the cathodes are contaminated with lead. To improve the mechanical properties of Pb-Ag-anodes alloying elements such as calcium, strontium, barium and others are added. The production of cast lead-silver or lead-silver-calcium anodes often results in the formation of numerous holes, voids or laps in the anode surface that can initiate localized internal corrosion. Based on the experience as the major supplier of rolled anodes for copper electrowinning, RSR Technologies has developed an improved anode for zinc electrowinning. The anode consists of a rolled Pb- Ag-Ca-alloy with a controlled surface grain structure. It forms an adherent protective oxide coating within 2 - 3 days when placed in an electrowinning cell. The preferred calcium and silver contents of the alloy are 0.03 - 0.08 % and 0.3 - 0.4%, respectively. Rolling sheets significantly reduces the presence of internal porosity or laps. The lack of defects results in long anode life. The rolling also produces a uniform grain structure to which the corrosion product readily adheres, thus significantly reducing the conditioning period.

Jan 1, 2000

By Ivanildo Hespanhol

"DALYs are a measure of the health of a population or burden of disease due to a specific disease or risk factor. It evaluates the time lost because of disability or death from diseases compared with a long life free of disability in the absence of disease. DALYs are calculated as the sum of years of life lost by premature mortality (YLL) and years of healthy life lost in states of less than fully health, i.e., years lived with a disability (YDL), which are standardized by means of severity weights, thus: DALY=YLL+YLD.WHO has established for wastewater use in irrigation (1) the same reference level of health protection as established for drinking water quality (2), i.e., the additional burden of disease from consuming water irrigated food should not exceed 10-6 DALY(Disability-Adjusted Life Years) loss per person per year (pppy). This level of risk means that a single additional case of disease may occur in a population of 1 million, during a life time (70 years). In a individual basis is equivalent to the occurrence of a mild disease during about 31,5 seconds.Such a restrictive risk is almost impossible to be attained in most developing countries which may not be able to afford the cost of wastewater treatment and of other protective measures, even for restrict irrigation.This paper presents proposals to adapt the reference level of risk to local technical, cultural, economical and social conditions of developing countries on the basis of a risk benefit approach."

Jan 1, 2008