Search Documents

By N. J. Rarmrez, C. Perez, J. D. Calderon, L. Lopez

"Among the thermal characterization of any material, one of the variables to know is the coefficient of thermal conductivity because this value can tell how much heat passes through the material and if the material could be used as an isolator. In order to determine this parameter is required some kind of special equipment and controlled conditions which implies high costs in the development of tests. The present paper proposes a design of a low cost measurement system in order to determine this coefficient with the lower possible error. This equipment was thought for companies or labs where they do not have the economic resources or the infrastructure (environmental controlled labs, heat flux transducers, human resources with specialized knowledge) to do this kind of tests.The system is based on ASTM C 518 - 04 [l] and integrated by two plates (one that contains a thermal resistance and which temperature is controlled by a closed loop controller and the other one with a route of water flow). The thermal resistance is actuated by a relay and a supervisor system checks the total time the relay is on in order to determine the effective power applied to the system. The contact faces of the plates contain a group of temperature sensors connected to a data acquisition system that process and record the temperature in each measurement point.With the power applied to the system, the measurement of temperatures and a process of calibration is possible to determine the coefficient of thermal conductivity. IntroductionWithin the thermal characterization of a material of known variables is the coefficient of heat transfer, since this value can know the amount of heat the material is capable of transferring or isolating. To determine this ratio requires specialized equipment and controlled conditions, which implies high costs in the development of a test. This article proposes a design of a low cost machine to allow closer this coefficient with the least possible error. This equipment was done thinking about companies that do not have the infrastructure (laboratories, controlled environment, heat flux sensors, human resources expertise) and financial resources to conduct these tests."

Jan 1, 2011

By Michael J. Nicol

This paper summarizes some of the results of a study of the reactions involved in the Caron leaching process and identifies the roles of the major dissolved species in the kinetics of dissolution of iron alloy particles formed during reductive roasting. Using rotating disk electrodes and synthetic leach solutions, the reduction of water with the evolution of hydrogen was found not to occur on a dissolving iron surface under typical leach conditions. It has been established that the oxidative dissolution is governed primarily by a reaction involving reduction of Co(III) to Co(II) ions. The reduction of oxygen was also found to make a significant but largely indirect contribution to the kinetics of the dissolution process. The dissolution rates of various iron-nickel-cobalt-copper alloys which simulate the dissolving alloy particles in a Caron plant were measured in synthetic leach solutions under aerobic and anaerobic conditions. The initial dissolution rates of iron, nickel and the iron alloys were found to increase in the presence of thiosulphate, whereas the thiosulphate had a negative effect on the dissolution rates of cobalt and copper. It is shown that the eventual passivation of the iron occurs sooner in solutions rich in Co(II) ions. Whilst these conditions are present in the quench slurry, on-site measurements have shown that due to the very high concentration of reduced dissolved species, passivation does not occur until the slurry is strongly aerated. In the light of these fundamental findings, options for optimizing the rate of dissolution and minimizing the extent of passivation of the iron and iron alloys are discussed. Keywords: Ammonia, leaching, alloy, kinetics, passivation.

Jan 1, 2004

By I. M. S. Moraes

Caraiba Metais has a plant for the purification and the cristallization of the crude nickel sulfate removed from its copper electrolyte purification system. In November 1994, an interdepartmental group was formed to study the Q.F.D. method, through its application on the improvement of the quality of the nickel sulphate hexahydrate. The team, formed with representatives of the following areas : production, technology, marketing, sales, maintenance, laboratory and TQC office, had also the task of checking the applicability of the method to other products of the comp any. This paper describes the main steps such as the survey of customer's demands, the preparation o1 the quality matrix, stablishing the planned quality matrix, the planned and the designed quality, and the consequent identification of the engineering bottlenecks. It is also shown how these bottllenecks were studied and solved. The application of the method allowed the team to identify means of increasing the production capacity by 40%, to improve the intrinsic quality of the product (including packaging), and to increase the reliability of the process.

Jan 1, 1997

By John L. Sundstrom

Complete systems were designed -and are in operation to recycle the effluent streams and to remove impurities from tankhouse. electrolyte, Heavy em¬phasis was placed on making usable products from as many streams as poss¬ible at minimum capital and operating costs. Almost complete recycling: and reuse of water and sulfuric acid were paramount. Techniques used in-clude solvent extraction - electrowinning, evaporation - crystallization and filtration.

Jan 1, 1992

By E. S. Geskin

"This paper is concerned with the construction of a formal technique for the selection of a metallurgical technology. Exergy consumption is used as the criterion of process efficiency. Different items of the exergy balance are considered and techniques for the reduction of exergy consumption are determined. The selected techniques of exergy saving enable us to identify processes which should be used at different stages of steelmaking. The combination of the selected processes enables us to suggest a technology for conversion of iron ore into steel products. The selection of this technology narrows the range of further search of metallurgical processes. The paper shows that qualitative thermodynamic analysis can be used as the first step in the design of metallurgical processes. IntroductionThe existing processes for making, shaping and treating of steel enable us to convert the available iron bearing ores into marketable steel products. However, the energy cost of metal production is much higher than thermodynamically required, while the metal properties are much lower than thermodynamically available. Increasing cost and declining availability of energy and raw meterials make the creation of new steelmaking technologies imperative. In recent years, the number of novel processes for the making, refining, and shaping of steel have been suggested and tested. Some found a practical application. However, the tested technologies make up a small portion of the physically available routes for the conversion of iron ore into a marketable product. It is also not evident that the optimal routes have been tested and that the selected technologies are the best among those tested.Although the development of new metallurgical technologies must be based on the experimental and practical information, the number of the alternative routes for the making, shaping and treating of steel, as well as the cost of examining each single route, make necessary the use of analytical techniques for the evaluation of the possible ways of process development."

Jan 1, 1988

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior of TiO2 nanoparticles was thermogravimetically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanoparticles, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500 °C at heating rate of 1O 'Cumin. The weight increase curve showed a maximum of ca 30 wt% at around 750 T and then gradually decreased to ca 12w% at 1000OC. This would be caused by the formation of TiS2 followed by the decomposition of TiS2 to lower sulfides, such as Til.08S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanpparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By Yutaka Yasuda

The particle dispersion phenomena in a turbulent gas jet of the flash smelting process has been investigated. The particle number density in a non- reacting jet was measured experimentally by taking photographs of the particles in flight and counting them using the image analysis. Numerical computations were also performed using a mathematical model for a turbulent particle laden gas jet The experimental particle number density data were then compared with the predicted results of the model. Good agreement was obtained between the experimental and predicted data. The effects of the parameters such as the injector design, particle loading and air flow rate are discussed. Optimization of the concentrate burner design can be achieved with the help of experimental and theoretical simulation as performed in this work.

Jan 1, 1994

By M. J. Bagshaw, J. D. Hunt, R. M. Jordan

"Continuous casting processes, and the roll casting process in particular, offer considerable potential to the Aluminium industry, both meatallurgically and economically.The three major limiting process problems that occur during roll casting are Centre Line Segregation', 'Sticking' where metal adheres to the rolls during casting, and 'Heat Line' formation. 'Heat Lines' are localised semi-continuous longitudinal defects, usually a few cms in width, where the cast metal leaves the roll bite partially molten. These defects occur at relatively low casting speeds when the mean slab exit temperature remains several hundred degrees below the solidus temperature. The objective of the work described here is to develop a better understanding of the roll casting process in general, and in particular, to understand the phenomenon of 'Heat Line' formation.A steady state two dimensional finite difference model has been developed to describe the roll casting process, incorporating a variable heat transfer coefficient through the roll bite. In the model the difference equations are formulated using a control volume method and latent heat is incorporated according to the Scheil equation. A Gauss-Seidel type technique is used to obtain the solution. Because the rate of heat evolution is non-linear the temperature in each box is determined by using a Newton-Raphson method. The solution for a box can be multi valued and therefore lead to instability particularly near the vicinity of the front. A stability 'criterion is presented which shows that to obtain a stable solution it is better to have long narrow boxes rather than boxes with small dimensions in both directions.The model explains why heat lines form in terms of the variable slab/roll heat transfer coefficient.Experimental measurements of slab exit temperatures are also presented. These were obtained on a Hunter twin roll caster for the binary AI-Cu system, at two compositions over as wide a range· of casting speeds as possible. The experimental results are compared with the predicted ones."

Jan 1, 1986

By Aarne Kopanen

In recent years, various renovations have been carried out in the production chain of the Outokumpu copper refinirg process. The anode casting shop, which is the final integral production section at the Harjavalta copper smelter built in its original form in 1945, was fourxl unsuitable for technical and capacity demads during longer periods of operation, and a new casting shop was built in 1974. The electrolytic copper refinery of Outokumpu Oy at Pori was built in 1941, and subsequently expanded in two stages. Even with its present limited scale of production it has been fom important to mechanize the main operations. This work was started in 1967 with the design and construction of the starting sheet machine connected with the cathode washing and unloading machine as a combined unit. Mechanized treatment of anodes has gained advantage particularly from the new design of a highly automated anode casting shop. In the further development of the mechanization a stripping machine for, starting sheets was designed and installed, starting operation in 1974.

Jan 1, 1976

By Minge Zhao, Yuandong Pei, Zhixing Zhao, Zejun Ma, Lili Ban

"Confocal scanning laser microscope (CSLM) has been applied to carry out the in-situ observation of melting and solidifying characteristics during iron ore sintering process, accompanied with TG-DSC test. It can be found that apparent Liquid phase forming temperature(LFT) and ending solidifying temperature(EST) is about 1190? and 1160?, respectively. Forming liquid phase during sintering process goes through four courses, these are shrinking, expanding, shrinking and expanding coexisting and expanding totally. For Yandi fine, the corresponding temperature of these four courses is about 1120-1160?, 1190-1196?, 1218-1220? and 1233-1270?, respectively. Although CAJ fine has more difficulty in forming initial liquid phase, but when liquid phase expands, it may have better fluidity and easier for liquid phase formation. Adding enough CaO, CAJ fine takes on high fluidity like Yandi fine, because liquid phase during sintering process is formed mainly by reaction between CaO and Fe2O3.IntroductionConfocal scanning laser microscope (CSLM for short) has been applied to carry out the in-situ observation of metallurgical phenomena, especially in steelmaking process. Recently, many researches on ironmaking process were conducted with CLSM. While for high temperature properties during sintering process, there are limited reports on in situ observation1-2). In this paper, melting and solidifying characteristics of iron ore were observed with CLSM under simulated sintering temperature, and high temperature properties of iron ore during sintering process was clarified based on the in situ observation results and TG-DSC research."

Jan 1, 2012

By Wilky Desrosin, Alicia E. Ares, Carlos E. Schvezov

"In the present research the horizontal directional solidification Zn-Sn alloys (Zn-4wt. %Sn, Zn- 6wt. %Sn, Zn-10wt.%Sn and Zn-30wt.%Sn) was carried out by extracting heat in two opposite directions. For this purpose, ceramic molds, a muffie, a horizontal furnace with two heat extraction systems at the ends, a measurement, acquisition and recording temperature system, eight K-type thermocouples and an electronic recorder were used. The main parameters involved in the columnar-to-equiaxed transition, CET, were: the moment of start and end of solidification at each position under consideration, cooling rates, the average temperature gradients and critical temperature gradients at the CET, the average speed of liquid and solid interphases left and right, advancing in opposite directions. Also, solidification kinetics was found to be different between horizontal solidification two-way heat extractions, with preliminary results of the vertical unidirectional solidification. In the solidification experiments, the velocity and accelerations of the liquidus and solidus interphases usually occurs at the end solidification zone of the samples.IntroductionSolidification of metal alloys, which starts in the external equiaxed region (chill), results in two basic types of structures in a single solidified alloy sample: columnar and equiaxed. The presence of both structures indicates the occurrence of the colunmar-to-equiaxed transition phenomenon[!].Studying the colunmar-to-equiaxed transition, CET, is of great technological interest for the evaluation and design of the mechanical properties of the solidification products. To this end it is necessary to understand the mechanisms by which it occurs. As found in previous studies [2-5], the CET occurs by competition between columnar and equiaxed growth. Mainly is controlled by the parameters of casting, such as the alloy composition, the density of the present nuclei in the liquid, the cooling capacity of the metal I mold, and the degree of convection in the liquid [7-10]."

Jan 1, 2014

By Susumu Nagae, Hajime Ikeda

Recently, a number of mine development projects have been setback by social, economic and, environmental circumstances that had not been seen before. Many of these problems do not always originate from direct mine pollution. Typical examples of these are· conflicts between the exploration company and the local residents, sudden objections just before the development is to begin, and unexpected tightening of environmental regulations. The common background to these problems is expanding global environmental awareness. This includes complex factors ·such as the expansion of exploration to remote regions, the brisk activities of environmental NGOs, the increase of international environmental laws and, governmental policy changes. Today, the range of issues concerning mine development is widening significantly. The participation of local residents arid NGOs in the development planning, together with the company and government, has become essential for smoothly carrying out mine projects and making them more beneficial for stakeholders. Introduction The common image of the environmental problem with respect to mining is direct mine pollution, such as the collapse of tailings dams, pollution from refineries, and acid mine drainage. All over the world, the mining industry has made large investments in capital and technology to solve and prevent mine pollution, and these efforts have been making steady achievements. However in recent years, new cypes of environmental problems which are not originating directly from mine pollution are emerging frequently. Most of the problems are concentrated at the exploration stage to early stage of development, which have less impact on the environment. In the worst case, mining project may be forced to cancel and could cause serious damage to the industry because they could not collect their investment. I would like to take a general view of the examples of new types of trouble, their characters, background, and strategies against these problems.

Jan 1, 2000

By D. A. Horne, V. R. Daiga

Certain steel mill wastes contain significant amounts of zinc oxide due to the use of galvanized scrap during the steel making process. Typically electric arc furnace (EAF), and basic oxygen process (BOP) flue dusts contain 20 to 30% zinc oxide and 40 to 50% iron oxides, along with smaller quantities of lead and cadmium. These materials can be recovered from the flue dusts by using a proven rotary hearth furnace (RHF) process. By-products of the recycling operation include a crude zinc oxide fume, which is captured in a baghouse filtering system, and sponge iron that may be recycled into the steel making operation. Crude zinc oxide properties plus the operating experience from two commercial RHF installations utilizing MR&E's DRyIron™ Process will be presented.

Jan 1, 2000

By Elsa Agante

Recycling of solid wastes, a common practice nowadays, requires the separation of the different materials in order to increase the products added value. The separation of one plastic from mixtures of different types of plastics is not easy due to their similar physical properties, but different techniques are available, from automatic sorting systems based on optical sensors to techniques adapted from mineral processing, namely gravity, froth flotation and electrostatic processes. In the last decade, many researchers have addressed the separation?s problem of different polymers, like Polyethylene Terephthalate (PET) and Polyvinyl Chloride (PVC), two polymers commonly used in packaging which have similar density. One proposed technique is the classical froth flotation performed in agitated cells. Froth flotation is a versatile and relatively cheap process widely used in mineral separation. It is based on the different behaviour of particles in the presence of an inter-phase air-water, which depends on the materials surfaces properties. Froth flotation can be affected by some variables such as impeller speed and air flow rate. Agitated cells, when used with low density materials, like plastics, can produce overstated turbulence that prevents the adhesion and collection of particles in the froths. In this case, separation is favoured by column flotation smoother hydrodynamics. This paper proposes the separation of PET from PVC by column flotation. The experimental work was carried out in a column of 9cm diameter and 1m high. The effects of some operating conditions, such as depressor and frother concentration, air flow rate and feed grain size on products grade and recovery were evaluated and the best flotation conditions for the separation of these plastics were established.

Jan 1, 2006

By Ryokichi Shimpo, Akio Fuwa

"The process-measurements of copper smelters in Japan were investigated for the summary of the latest technique and for the fundamental study of process control. The smelters investigated are those employing flash smelting furnace and P.S. converter, one reverberatory furnace and P.S. converter, and one continuous smelting converting furnace (M.I. process). Respective process is then considered, consisted of several reactors of different functions. The measurement methods were summarized in each reactor, including the measurement points. The methods of chemical analyses of the samples in each reactor were also investigated.IntroductionAn investigation on the process measurements, chemical analyses, and system control in copper smelters in Japan were carried out for understanding and summarizing the technique of the pyrometallurgical copper smelting operations. The typical seven processes in six copper smelters were investigated in the period from 1985 to 1987. The smelters investigated were Touyo Smelter of Sumitomo Metal Mining Co., Ltd., Kosaka Smelter of Dowa Mining Co., Ltd., Saganoseki Smelter of Nippon Mining Co., Ltd., Tamano Smelter of Hibi Kyodo Smelting Co., Ltd., Ashio Smelter of Furukawa Co., Ltd. and Naoshima Smelter of Mitsubishi Metal Co., Ltd. They include five flash smelting furnace and P.S. converter systems, one Mitsubishi continuous smelting and converting process (M.I. process), and one reverberatory furnace and P.S. converter system.The investigation was performed by making inquiries about the measurements, chemical analyses, system control, and their future prospects to the engineers in each smelter and by summarizing up in each item. The system control and future prospects were summarized in another paper titled ""Process Control Scheme of Copper Smelting Processes in Japan and Future View."

Jan 1, 1989

By Andrzej Szymanski

Recent developments in medicine have stimulated activities that? involve mineralogy. They include inplantation of inorganic and organic parts into bones and soft tissues, and uses of elements as basic stimulators for the human body. In addition contamination of the environment has increased the concentration of sane elements in food. Consequently f both the environment and food structure vary with geographical regions and influence human health. These activities in medicine have created the new fields of biomineralogy and of biogeochemistry as activities for the future.

Jan 1, 1989

By K. Abe

Onahama Smelter has two green-charge reverberatory furnaces and the annual smelting capacity is 600 thousand tons copper concentrate. In addition to the concentrate, various kind of industrial wastes has been processed and utilized. First, the brick waste from converter is ground and used as raw material of castable for repairing the copper melt launders. Second, the slag containing calcium-sulfide from other foundry is fed to the reverberatory furnaces. Calcium sulfide is oxidized to CaO. The melting rate of concentrate is accelenlled and the slag loss is decreased. Third, the tip tire made of waste car tire is charged into the reverberatory furnaces as fuel. The steam of waste heat boiler for turbine generators has been increased so as to decrease the electricity cost. Fourth, the sulfur accretion from other chemical plant is blended into the copper concentrate and the sulfur is recovered as the gypsum for sale. Fifth, the processed waste oil has been utilized in the copper concentrate dryer by which the smelting capacity was increased effectively. Consequently, Onahama smelter contributes to the society by processing the wastes to the harmless slag and utilizing them as fuel through the copper smelting.

Jan 1, 1996

By Luis W. Pommier

The wastes of the plating industry are generated in the process of rinsing the plated objects and during the cleaning of the plating shops. High volumes of hazardous waters are neutralized on site producing recyclable water, generating a metal rich, hazardous, filter cake. Occasionally, a complete plating bath has to be discarded which increases the metal content of the filter cakes. These filter cakes are discarded as hazardous at a cost of over $ 250 per ton. The metals found in the cakes are generally copper, nickel and chromium or zinc, lead and cadmium, assaying from 2% to 15% or even higher content of each metal The metals and their contents are highly variable. Some plating shops discard their products directly to hazardous waste sites, others, have them collected by companies which consolidate wastes from several producers prior to discarding. These wastes, richer in metal content than mine ores, need neither mining nor crushing and grinding for concentration. The commonly found impurities in the mine ores, i.e.: pyrites, arsenic, and valuable metals which are present in minute quantities, are absent in the filter cakes. The processes available to selectively recover the metals from the filter cakes, are discussed based on their technical and economic merits. The flow-sheets include leaching, solvent extraction when required, and electrolytic refining. Examples, showing the separation of copper, nickel and chromium and also of zinc and lead in pilot plants, show the technical and economic viability of the processes.

Jan 1, 1996

By Robert W. Hyers

Electromagnetic levitation has proven important in a wide range of experiments, all affected by fluid flow. For some experiments such as viscosity measurements, only whether the flow is laminar or turbulent must be established. For other experiments, however, quantitative assessments of velocity, shear stress, or shear strain rate are required. In most cases it is difficult or impossible to measure the internal flow in levitated droplets directly. The samples are usually small, opaque, reactive, high-temperature, metastable, or all of these. Furthermore, recirculating flow limits the utility of tracking surface particles, since they collect in stagnation points ratherthan following the flow. Most research groups have chosen mathematical modeling to assess the internal flow in levitated droplets. A variety of analytical and numerical methods have been applied, including both laminar flow and various turbulence models. A number of these models are reviewed and their impact on different containerless experiments is assessed. Much of the research reviewed here was performed by alumni of Professor Julian Szekely, and by others using similar methods.

Jan 1, 2006

By Peter Kettle

This paper describes the performance of the copper industry over a period of some two decades and examines the theme that improvements in operating efficiency have not been matched by improved returns on capital. The financial performance of the copper industry is analysed using CRU's MICA database. Regression analysis indicates a two percentage point increase in operating margins but no increase in returns on capital. The gain in operating efficiency appears to have been mainly achieved in the mid 1980s. The investment boom of recent years has resulted in a rapid increase in the industry's level of debt and gearing ratio (now some 47%). Data on 44 copper mine projects is used to show the linear relationship between scale and capital costs. Typically new capacity costs some US$5,000 /tpy. The relationship between cash costs and capital intensity of projects is also plotted. The greater attention now being focused on efficient use of capital means that capital intensity rankings will become increasingly important in determining which projects go ahead.

Jan 1, 1999