Search Documents

By Muhlis Nezihi Saridede, Burak Birol

"Plastic wastes become a huge problem day after day due to the growth of plastic industry. Hence, plastic wastes are used as a raw material for other industries to eliminate this problem. Polyethylene Terephthalate (PET), which is a commonly used for plastic bottles, may be used as a reductant for iron production because of its C and H content. In this study, composite pellets containing iron ore concentrate, flux and reductant were prepared. Crystallized PET bottles and coke were used as reductant after ground. The prepared pellets were reduced at 1400°C for 30 min. and iron nuggets were produced successfully. Usage of waste PET purely as reductant in composite pellets gives a higher metallization degree and proper carbon content than coke or PET and coke mixture.IntroductionPlastics can be seen everywhere, especially at packaging industry in our common life. The increase of plastic usage ends up with an important problem, the increase of plastic wastes. Many studies have been carried out about usage of plastics as reductant in blast furnace such as Ogaki et al.[1], Heo and Baek [2], Saridede [3], Minoru et al.[4], etc. Besides, Kato et al. [5], Nomura and Kato [ 6] and Rongfang et al. [7] have pointed out the use of plastics in coke ovens regarding to its calorific content. In EAF steelmaking, a mixture of coal/coke and plastics can be used as an energy resource instead of only coal or coke. [8] Also, the usage of PET and PC in self-reducing composite pellets increased the reduction rate. [12]PET (Polyethylene terephthalate ), which is commonly used for soft drink plastic bottles, is an important municipal waste due to its C and H content. Its molecular formula is (C10H8O 4)n. Demir and Dincer showed that PET can be crystallized at 250°C to have the ability to be ground to a size of -100 µm. [11]"

Jan 1, 2011

By Kyle S. Brinkman, Kenneth L. Reifsnider, Fazle Rabbi

"Mixed ionic and electronic conducting (MIEC) ceramic membranes are HeteroFoaM's which play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC), oxygen separation and permeation membranes, partial oxidization membrane reactors for natural gas processing, and high temperature electrolysis cells. Dual phase oxygen membranes consisting of an ionic conducting phase Ceo.sGdo.z02 (CGO) and an electronic conductive phase C0Fe204 (CFO) were fabricated and characterized by structural (XRD), microstructural (SEM-EDS) and broadband dielectric measurement techniques. In-situ measurements of the dielectric properties of working oxygen separation membranes are presented which indicate that the material's dielectric behavior can be an indicator for MIECperformance.IntroductionCeramic membranes which transport oxygen ions play an essential role in a number of energy conversion related systems including the solid oxide fuel cell (SOFC) [l ], oxygen separation and permeation membranes in the commercial and nuclear arena [2, 3], partial oxidization membrane reactors for natural gas processing [4], and high temperature electrolysis cells [5]. For the electrolyte functions, the membranes must transport oxygen ions only. On the other hand, permeation membranes, typically used in combustion devices to support oxy-fuel combustion or for partial oxidation reactions involving the production of synthesis gases, require mixed oxygen ion and electronic conduction (MIEC). Traditionally the tailoring of the ratio of ionic conductivity to the materials electronic conductivity, measured as the transference number, has been accomplished by the introduction of aliovalent doping elements creating point defects in the material facilitating the diffusion of charged species. However, several decades of research have not yet produced single phase materials which possess the concomitant ionic and electronic conductivity required for use in membrane separation applications. It is clear that novel ""dual phase"" heterogeneous materials will be required and that the surface reactions of these materials will be of particular importance as the industry moves toward thin films membranes [6]."

Jan 1, 2013

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By M. T. Ernett

Significant amounts of arsenic are often present in effluents arising from the mining of sulfide ores for the extraction of metals such as copper, gold, lead and zinc. The arsenic is usually removed from the process effluent by co-precipitation with iron because of its common occurence in the mined ore bodies and the excellent adsorptive property of the precipitated hydrous ferric oxide compound. There has been controversy, however, over the long-term stability of the arsenic-bearing ferrihydrite which is produced. This paper presents the results of laboratory studies which indicate that the cations of calcium, magnesium, zinc, cadmium and lead, increase the pH range of effective arsenic adsorption in the Fe-As precipitate from 4-7 to 4-9. The increase in the pH range is similar for all of the added cations investigated. Sulphate ions are shown to have a minimal effect on the residual dissolved arsenate concentration. Silicate ions reduce the adsorptive capacity of ferrihydrite if they are present before the arsenic is adsorbed.

Jan 1, 1994

By M. I. Kalashnikova

Gipronickel Institute has developed the technology of treatment of difficult to concentrate sulphide Pb-Zn concentrates (Zn-19,9%, Pb-8,4%, Cu-0,34%, Fe-8,8%, Ba-6,8%, S-18,7%, Ag-106 g/tonne). The technology consists of pressure leaching, impurity removal from leaching solution, electrowinning and Pb-Ag containing cake treatment. Despite low zinc content in initial concen-trate the technology allows production of solution which is suitable, after standard procedure of impurity removal, for electrowinning with production of zinc grade SHG. Comparing to the standard technologies the flowsheet developed provides the lesser expenses per zinc unit because of decreasing of liquid to solid ratio at pressure leaching stage. The initial concentrate is characterized along with low content of principal metals by high con-tent of barite, which makes flotation of pressure leaching residue more difficult. That is why in this case the hydrometallurgical treatment was chosen. At optimal parameters of chloride leach-ing found during laboratory experiments the principal components extraction was 99.5% for Pb and up to 92% for Ag.

Jan 1, 2006

By J. E. Murphy

Neodymium was electrowon into a Mg-Cd molten cathode at 650 °C from NdC1,-KC1 electrolyte. With the chloride system, neodymium was deposited into the molten alloy cathode until the neodymium concentration reached 20 wt pct. The alloy was then vacuum melted to remove the Mg and Cd. The current efficiency exceeded 80 pct under optimum conditions and the purity of the metal was 99.9 pct after vacuum melting. As an alternative approach, neodymium was electrowon at 1,030 °C from Nd,O, dissolved in a molten fluoride eleotrolyte. With the oxide-fluoride electrolyte, the metal was electrowon in a molten state with current efficiencies up to 60 pct. The purity of the metal was 99.8 pct with oxygen and carbon as major impurities. A number of problems were encountered including anode effect, low oxide solubility in the electrolyte, high neodymium metal solubility in the electrolyte, and reactivity of the metal with the cell materials. Approaches to improved cell, operation and prospects for commercial adoption of the electrolytic production of neodymium metal are discussed.

Jan 1, 1995

By Vinay Kumar, Jae-Chun Lee, Rakesh Kumar, Manis Kumar Jha, Archana Kumari, Pankaj Choubey

Present work is a part of developing novel recycling technique for waste printed circuit boards (PCBs) i.e. the liberation of metals from PCBs by organic swelling followed by the treatment of resin to remove/ recover hazardous soldering materials. In order to recover the hazardous metallic constituent lead from the liberated resin, initially the leaching studies were made using fresh solder containing 63.9% Pb and remaining tin. Experimental results obtained in different conditions viz. time, temperature and acidity showed -97.20% of lead dissolution with 6M HNO3 at solid to liquid (S:L) ratio 1:10 (g/mL) and temperature 90°C in 75 minutes. The result of the studies validated with crushed PCBs shows that almost total lead and tin was leached out with 6M HNO3 and 6M HC1 respectively at S:L ratio 1:10 (g/mL) and temperature 90°C within 50 minutes. The results will be useful for the treatment and safe disposal of PCBs resin.

Jan 1, 2011

By Scott R. Giese, Lucas Dix

"Recently, there is a growing trend in the aluminum foundry industry to develop· improved melting and casting processes to produce lightweight, high-strength, and thin-wall castings for the aerospace and transportation industry. One casting method that has demonstrated industrial potential for producing clean, thinwall castings is vacuum-assisted, counter gravity casting. This process has the benefit of expeditiously and quiescently filling the casting cavity with a dramatic reduction of furnace related and reoxidation inclusions. Additionally, lower casting temperatures can be utilized because the application of vacuum during filling overcomes the resistive internal cavity pressure resulting in a finer, as-cast microstructure. The paper explores and discusses the processing and design conditions in improving the mechanical properties of A206 casting alloy using the vacuum assisted, counter gravity casting process.IntroductionThe process of metal casting has been, over the centuries, the chief production technique for components used in everyday life. However, the casting process has certain inherent problems that can adversely effect the properties of a finished product. These problems are directly attributable to the gravity pouring technique used to transfer molten metal to the mold and to fill the mold cavity.A recent study for the American Metalcasting Consortium demonstrated reoxidation products created during the casting process are five times more likely to cause product rejects than entrapped molding aggregates, melt slag, or furnace lining materials1. Formation of nonmetallic and intennetallic compounds are more prevalent in aluminum and titanium alloys because of their reactiveness to furnace lining materials and their high affinity for oxygen. The incorporation of undesirable compounds can be attributed to four areas of the casting operation. The sources are charge materials, melting technique, pouring methodology, and casting cavity filling. Aluminum foundry men have addressed the first three areas by selecting high quality melt stock, non-stirring melting equipment, and the use of porous ceramic filters. Unfortunately, little consideration is given to the last, but yet tl.1e most important part of the casting operation, the actual fill mg of the casting cavity.The generation of inclusion defects during the casting process can be described by two methods. As the liquid metal flows in the gating network and casting cavity, abrupt changes in flow d1rect10n cause the metal to become agitated. This mechanism liquid metal splashing, is generated by instability of the advancing liquid metal interface from turbulence effects as schematically illustrated in figure 1a2 . The surface oxide film bursts under high velocity conditions, folds over, and becomes dispersed and incorporated in the bulk liquid. Additionally, fragmented liquid droplets ejected from the disturbed interface oxidize and become dispersed in the metal stream."

Jan 1, 2000

By Supachai Surapunt

The distribution behavior of V A minor elements (As, Sb and Bi) in the smelting stage of the Mitsubishi process were evaluated thermodynamically based on thermodynamic data and operating data. The fractional distributions between the gas, slag and matte phases considered as the degree of vapor saturation of 1.0 are as follows: 53.8, 27.2 and 19% for As, 23.6, 56.6 and 19.8% for Sb, and 91.3, 1.1 and 7.6% for Bi, respectively. Arsenic is mostly distributed to the gas and slag phases. It is effectively eliminated by volatilizing and slagging. Antimony is mainly in the slag phase, which is suitably removed by slagging. Bismuth is easily vaporized to gas phase. The degree of vapor saturation has a large effeet on the distribution behaviors of the three elements between the three phases. The amount of a minor element in the charge has an effect on the distribution of As but no effect on the distributions of Sb and Bi. Increasing matte grade and temperature results in the change of distributions for As and Sb, significantly. The change in the distribution ratio between slag and matte phases also considerably affects the distributions of As and Sb. The distribution behavior of Bi is not significantly changed by the change in matte grade, temperature and distribution ratio.

Jan 1, 2003

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. Green balls with 0.8% bentonite and others with 2% hydrated lime were obtained under the same conditions of 1.5% coke, 1.45 basicity and balling at 8.5% moisture for 13 min in disc pelletizer. The properties of two types green balls were as follows: drop numbers of 4.8 to 5.0 times/0.5m, compressive strength of 19.7 to 24.2 N/pellet and thermal shock temperature of 280 to 385?, respectively. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8% and climbs up to 3113 N/pellet under the following conditions: preheating at 1050? for 10 min and firing at 1300? for 15 min. The hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6% to 70.6%, RDI+3.15 increased from 90.1% to 98.8% and reduction swelling index dropped from 22.4% to 7.4%, respectively. Therefore, hydrated lime can not only replace bentonite as binder to enhance the firing behaviors of green balls, but also effectively improve the metallurgical performance of fluxed pellets which can be used as high quality feed for blast furnace.

Jan 1, 2011

By Pertti Koukkari

The novel Jarogain process combines treatment of the jarosite residue of zinc manufacturing and processing of arc furnace dust from steelmaking to a holistic recovery technology. The new hydrometallurgical approach is targeted to recover the major constituents (Fe, Zn, Pb) as well as valuable components such as Ag, Au, In and Ga from the jarosite-dust mixture as reusable concentrates. The fractionation process proposed by VTT and Aalto University takes advantage of jarosite being readily fine powder and directly available for wet chemical processing. Jarogain process provides an energy efficient opportunity for jarosite utilization as value added products. The experimental proof-of-concept of key stages of the process will be outlined with a comparison of available pyrometallurgical treatments of jarosite waste. The techno-economical assessment is based on estimated investment and variable production cost using the discounted cash flow (DCF) analysis.

By F. J. Hogan

In early 1982 Atlantic Cement Company, a wholly-owned subsidiary of Newmont Mining Corp. will come on line with a new water granulating grinding facility at Sparrows Point, Maryland to produce 800, 000 tons a year of separately ground granulated blast-furnace slag. The process and product will be unique to the United States. This paper will review some initial investigations undertaken to evaluate the cementitious properties of granulated slag. The effect of slag fineness on strength development is discussed and data is presented showing a relationship between glass content and hydraulicity and grindability of slag.

Jan 1, 1982

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By Takashi Fujii

In the OG (Osaka Gas) process which includes a fusion process of sewage disposal sludge in coke bed knowledge of molten and fluid properties of the sludge are most important to controll the process in good condition. Thus, the softening and melting temperatures and viscosity were measured by the sessile drop technique and a rotating viscometer. Obtained results are summarized as follows: Melting character of sludge slag is varied according to their composition, but closely related to CaO/SiO2 ratio in ordinary sludge and to CaO/(Cr2O3,+Al2O3+P2O5) ratio in Cr2O3 containing sludge. Fluid property of sludge slag has a correlation with optical basicity or Riboud parameter, However, the correlation is poorer than that of metallurgical slags. Especially, chromium oxide containing sludge shows high viscosity and behaves somewhat different manner from ordinary sludge.

Jan 1, 1992

By Julie M. Melluish

The metallurgical response of the Point Leamington deposit has been studied. Two series of bench tests were conducted and various ore samples and flotation products were examined using image analysis techniques. The majority of sphalerite and chalcopyrite grains in this texturally complex ore were found to be smaller than 10 micrometres. Copper recoveries were low with losses mainly as fine inclusions in pyrite. Sphalerite recoveries were somewhat better due to a generally coarser habit. Gold and silver recoveries were also low and only solid solution silver was identified in the ore. The deposit shows poor economic prospects unless additional tonnage of high grade zinc ore can be delineated.

Jan 1, 1989

By M. D. Crites

As part of a multi-year program for assessing the viability of chrome-free refractories in copper smelting, converting and refining furnaces, dynamic corrosion tests have been conducted on a series of refractories from the magnesia-alumina system, using a ferrous silicate slag. The corrosion rates of the test refractories are compared with those of a reference mag-chrome brick, and recommendations are made for more in-depth evaluations of the more corrosion-resistant materials.

Jan 1, 1999

By Raj P. Singh

Two design-of-experiments studies were carried out to investigate the leaching of technical grade molybdenum tri-oxide (TGM) in the presence of hydrochloric acid and the mother liquor of ammonium di-molybdate crystallization used as an ammonia source. Results indicated that leaching of TGM in HCl is possible only when used at about 1N concentration. In high concentrations of HCl, technical grade MoO3 had very high solubility (7.5 to 40 g/L Mo). The most suitable conditions for HCl leaching of TGM were obtained at a slightly elevated temperature of 80°C. Using about 1N HCl at 80°C, potassium in the leached solids (TGM) decreased to about 110 ppm, a value typically obtained in TGM leached in HNO3 - NH4NO3media (3.5 - 4.0 moles /L HNO3 + 0.5 ? 1.0 moles/L NH4NO3). Mo losses under these conditions were 0.8-0.9 g/L Mo. The HCl-leach method, presented here-in, has a significant advantage in chemical cost and environmental benefits over HNO3 ? NH4NO3 purification method.

Jan 1, 2006

By Li Fangi

This paper describes the characteristics and regularities of a process to recover rare earth minerals from Baotou Ore with H-205 collector. H-205 is a kind of hydroxamic acid with amide as a polar group and poly-cycle aromatic hydrocarbon as a non-polar group, having strong ability to capture RE minerals (bastnasite, monazite). When adding a certain dosage of water glass and some other modifying agents, and maintaining pH value between 8.5 and 9.5, RE minerals can be effectively separated from calcium and barium minerals, such as fluorite and barite, etc. Under normal flotation temperature and concentration, when using H-205 to float RE minerals, it needs a bit longer conditioning time (a few minutes longer than that for the conventional collectors). It is also shown that the reagent has the property of resistance to hard water. The laboratory scale and pilot scale tests of the process have been carried out on bulk froth containing RE minerals and fluorite taken from Ore Dressing Plant of Baotou Iron and Steel Company, in both cases, high grade RE concentrates were obtained and the recovery increased remarkably. Therefore, the process has a great practical value.

Jan 1, 1989

By Hélio Wiebeck, Fabio J. Esper, Wildor T. Hennies, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz

"Natural rubber reinforced commonly with carbon black to produce vulcanized material, turns into a new environmentally friendly nanocomposite when carbon black is replaced by organically modified clays of Brazil. Carbon black is substance derived from the oil refining process with consequent pollution to the environment. Its substitution in this industrial process must contribute to diminish the oil derived products dependence. As the added clays are only a third in weight of the traditionally carbon black added, then, to obtain the same final volume it is necessary to add low cost neutral filler that does not damage the technological characteristics of the final material. This paper presents results using as neutral filler of this type rice husk ashes from industrial wastes. Experiences realized with this nanocomposite material show results of quality and technological characteristics similar or superior to those of the rubber made with carbon black.IntroductionTraditionally rubbers are black or a very dark color. But they can have different appearance when filler of distinct composition of the carbon black is used. The carbon black is substance derived from the oil gotten during the final phases of the mineral fuel treatment with consequent pollution of the environment. Carbon black show nanometric grain sized distribution and a depth black color, because these properties it is also used for computer printers inks production. The substitution of this substance, traditionally used as a reinforced load in the rubber production, will have to contribute in such a way to diminish the dependence of these products as to diminish the pollution of the environment. The present work shows the results of the use of another kind of mineral nanoparticulate material substituting carbon black in the production of some rubber products. This nanoparticulate material is the organic modification of smectite clay treated with some types of ammonium quaternary."

Jan 1, 2008