Search Documents

By John C. Stankus

ldentifcation of potential roof problems in coal mines has long been a complex issue due to the wide variety of mining and geological conditions. It is well known that mine roof falls are related to many different factors such as roof strata properties, sandstone channels, regional and localized horizontal stress, vertical stress, and tectonic stress. Many times, a combination of these factors causes roof problems. Through years of ground control experiences, Keystone Mining Services LLC, (KMS) has developed a Roof Instability Rating (TUR) system to predict potential roof problems. The first RIR analysis was presented at the 19th Ground Control Conference (Watts, et al., 2000). The RIR system includes: quantifying each individual factor, weighting each factor, combining individual factors, finalizing the RIR, and setting the criteria for the areas where special support is needed. In this paper, the application of the Roof Instability Rating (RIR) system at Enlow Fork mine will be presented.

Jan 1, 2001

By Michael J. Friedel

The fundamental problems associated with ground control reflect the inability of mining personnel to "see" the development of anomalous conditions. Toward this end, the U. S. Bureau of Mines is investigating the application of seismic refraction tomography for imaging the process of pillar yielding, at the Foidel Creek coal mine, near Steamboat Springs, CO. The inherent three-dimensional problem of imaging coal pillar stress is reduced to a single plane by considering only the stress transmitted from the pillar to the adjacent floor rock. This approach exploits the fact that refracted seismic energy is essentially confined to the adjacent higher velocity sandstone strata. The tomographic analysis using ray-tracing based on wavefront migration resulted in a robust P-wave tomogram from which regions of high velocity indicate zones of high stress concentration, whereas low velocity zones indicate regions of stress relief. The interpreted region of high stress concentration occurs at the pillar end nearest to the working face of the adjacent longwall panel. This finding is corroborated by vertical pressure cell measurements recorded in the pillar. The stress diminishes toward the pillar perimeter with local minima correlating to the locations of observed pillar spalling. Time-sequence monitoring, as the longwall face advances, is recommended for evaluating changing stress conditions.

Jan 1, 1993

By G. K. Rogers

Portals, which are the surface entrances to underground excavations, are frequently overlooked and often difficult areas In terms of ground control. Failures commonly occur In the typically high angle approach cuts and Initial subsurface portion of the portal. In order to permit rigorous design of all types of portal structures, failures are Identified and subsequently classified. Based on the failure classification and suggested analysis methodology, optimum ground and support loading can be determined.

Jan 1, 1988

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By Douglas Morrison

By applying modern 3D numerical modelling techniques to the analysis of a pillar cascade failure in a room and pillar mine, it has been possible to simulate the collapse and develop an understanding of the role of low rock strength areas within the mine. The cascade collapse occurred in a normal strength area but would not have occurred without the influence of a low strength rockmass in one section of the mine. The numerical analysis made it possible to develop a realistic assessment of the residual pillar strength. With the introduction of regular empirical pillar performance assessments, critical pillars or groups of pillars can now be identified proactively. This has led to an aggressive extraction ratio of 90% that manages pillar failure, avoids pillar and roof collapse and prevents surface subsidence. Since the mine also has significant waste products, the use of backfill for ground support has made it possible to significantly improve the performance of strategically located pillars, and so achieve even higher extraction ratios.

Jan 1, 2003

By Robert W. Bruhn

A 125 foot high steel lattice frame tower supporting a 500 kV EHV transmission line and located over the gateroads of a longwall mining operation was subjected to ground movements from the mining of adjacent longwall panels. Under an agreement with the owner of the powerline, the mine operator was required to minimize mining impacts on the transmission line. In view of this requirement, the mine operator prepared a forecast of the expected subsidence ground movements prior to the onset of mining. These forecasts, in conjunction with finite element analyses of the tower superstructure under the imposed ground movements and wind loadings. suggested that the structural capacity of the tower would probably be diminished little, if at all, by mining. Ground movements determined by survey during mining of the two longwall panels were found to be in close agreement with predictions. Strains measured in selected tower members during mining generally agreed with values calculated by the finite element analyses. The study confirmed a methodology to predict subsidence and to assess its effects on steel lattice transmission towers.

Jan 1, 1990

By Rodger Fry

All coal deposits contain anomalous geologic conditions which have an impact on roof control, Run-Of--Mine (ROM) coal quality and production costs. To remain competitive in today's coal market and provide a safe working atmosphere, mine operators need to know in advance of mining the geologic conditions which prevail in the coal deposit. In order to identify geologic anomalies within a coal seam and surrounding roof rock in advance of mining, the Radio Imaging Method (RIM) survey procedure has been developed. This paper describes the RIM procedure and how it is used to predict various geologic conditions within a coal deposit. Figure 1 illustrates the RIM in-mine and surface surveys which can be used in an underground mine. [ ] RIM is an electromagnetic (EM} wave process which consists of in-mine and surface survey techniques. Both techniques are used in underground coal mines to detect faults, interbedding, sandstone channels, and thinning coal. Thesurface survey can also be used to determine seam correlation and continuity in strip and underground mining. In-mine and surface surveys work by propagating EM waves along straight paths through the coal. As the RIM signal travels along a ray path, it interacts with the seam material and surrounding rock. This interaction causes the signal to lose energy thereby decreasing its strength along the path. The amount of energy loss per unit path length depends upon the coal seam height and type of surrounding roof and floor rock. A reading of the signal level is taken at the end of the ray path at the receiver location. This reading is used to determine the loss (attenuation) rate of the signal along the path. The signal level data is compiled and analyzed through computerized algorithms which construct images of any anomaly present. This graphical depiction of the coal provides a basis for further geologic interpretation. By comparing the images reconstructed by the RIM analysis to in-mine geologic mappings made while mining through RIM study zones, it has been confirmed that RIM can help detect the following; Rapidly Thinning Coal Incompetent Roof Rock Poor Floor Lithology

Jan 1, 1984

By Brian E. Travis

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to steel. The finished polymer mining grid product is a viable alternative to conventional supplemental roof control meshes such as chain link fence and welded wire. Polymer mining grids are a fraction of the weight, have comparable load support qualities, and will not rust or corrode in even acidic or alkaline conditions. Specific flame retardant additives can also be incorporated to make the polymer grid self extinguishing for use in underground "gassy" environments.

Jan 1, 1992

By Daniel W. H. Su

This paper presents a retrospective assessment of ground control research and its successful application by CONSOL Energy over the past 25 years. Recognizing the need to improve the understanding of coal pillar design mechanics under shallow, medium, and deep covers, an extensive underground coal pillar instrumentation program was initiated in the mid 1980s. Combined with sophisticated numerical modeling technique and laboratory tests, results from this instrumentation program were used to advance the concept of coal pillar design and to demonstrate that numerical modeling can be used to predict in situ coal pillar strength, especially under non-ideal conditions where interface friction and roof and floor deformation are the primary controlling factors. To evaluate the impact of longwall mining, a 10-year subsidence research program was initiated in 1986 that encompassed surface, subsurface, and underground measurements, as well as a sophisticated numerical modeling technique. Results from the research revealed that interface friction and shearing between rock layers within the overburden had a profound effect on surface subsidence development and the resulting strain. Recognizing the impact of horizontal stresses on CONSOL?s mining operations, extensive horizontal stress measurements were conducted using the USBM Borehole Deformation Gage and the CSIRO Mininfrac system in the mid to late 80s. Roof extensometers and CSIRO HI Cells were used to measure roof displacement and roof stress concentration in longwall headgates and tailgates, which resulted in the definition of right-hand and left-hand longwall panels. Pillar design modifications, combined with cable bolt application and innovative standing support installation, were then successfully employed to mitigate horizontal stress impact on the right-hand longwall headgates and left-hand longwall tailgates. An in-house floor bearing capacity test apparatus was fabricated and employed underground to determine mine-specific floor bearing capacities which, along with other geotechnical parameters, were then used in the mine-specific shield design. To promote caving of thick, massive sandstone immediately behind longwall face supports and to improve face conditions, the hydraulic fracturing technique was successfully employed by CONSOL to pre-fracture the sandstone prior to longwall mining. Face monitoring and numerical modeling confirmed the effectiveness of the hydraulic fracturing technique. A roof geology reconnaissance program was initiated by CONSOL in the early 1990s to improve roof control, safety, and production. Information obtained from the reconnaissance program was used successfully to guide mine planning decisions and daily roof support practices.

Jan 1, 2011

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By H. N. Maleki

The results of five years of geotechnical investigations are presented to develop productive and stable longwall layouts for the Foidel Creek Mine. The program was initiated during the pre-mining stage, and has continuously provided the data required for mine design. From several stress determinations at the mine, the relationship between geologic structure and the stress field/depth was established. The results were used for orienting the entries for improved stability. Cave conditions and load transfer to panel boundaries were evaluated from closely monitored full extraction mining and computer analysis. Back-analyses of ground movements, as compared with the actual measurements, indicated that cave conditions were favorable in spite of the presence of competent, thick-bedded sandstones in the mine roof. Gate pillar design using a yield-rigid concept was developed through computer analyses and underground instrumentation, resulting in 35 and 75 ft wide pillars. The influence of a slickensided bedding plane at the roof contact on pillar yield zones, core confinement, and pillar behavior was evaluated.

Jan 1, 1988

By Ding Xu Chu

There are many methods developed for measuring the crustal stress in China. Among them only two methods have been adopted in practice, i.e., overcoring method (for which the sensors include: Piezo-magnetic stress gauge, steel-ring strain cell, 3-dimensional hollow-inclusion stress ,gauge, and Leeman's-like stress gauge) and hydraulic fracturing method. For the former method, one of those sensors is installed in a borehole, 36 mm in diameter, then prestressed, and finally overcored with a drill bit of 130 mm in diameter. After that the deformation of the borehole wall is measured, from which the in-situ stresses are determined. In order to avoid the errors resulting from the difference in elastic modulus for various kinds of rocks as well as from the installment of the cells, we have developed a technique to calibrate the sensor on-spot using a confining pressure calibrator and produced a very good result. For the later method, the measurements are achieved by isolating a certain section of a borehole and then injecting water to pressurize it till a tensile break is induced. It is identical to the typical technology used internationally. For many years, through field observations and a large number of laboratory experiments, we believe that the most efficient way of stress measurement for engineering purposes is the overcoring method using Piezo-magnetic stress gauge. It is characterized by stable and reliable measurement values, high accuracy and high adaptability. Taking the measurements in the intact rock mass as an example, the measured stress magnitudes are within accuracies of 8% and the errors in orientation are about 5 degrees. It can even be used perfectly in deep water. Up to now, we have performed in-situ stress measurements in more than 70 sites and obtain more than one thousand sets of data. The deepest depth used in the overcoring method is 80 m in vertical borehole and 780 m in tunnels.

Jan 1, 1987

By Naj Aziz

A series of laboratory experiments were conducted on a variety of bolt types to examine the load transfer capacities of different profiled bolts in short encapsulation push testing. A 75 mm section of 150 mm long bolt specimen was anchored in a 75 mm long stainless steel tube using full resin encapsulation. Six types of different profiled bolts and two non - profiled bolts were tested. Bolts with higher profile were in general found to have greater shearing resistance and higher stiffness than low profile bolts. Widely spaced profiles allowed greater displacement at peak shear strength, and bolts with no profiles produced very link load transfer capability. Rough surfaced plain bolts showed a significant load transfer capability in comparison to a factory supplied smooth surface bolt which supports the belief that rusted bolts have higher lnad transfer capability that un-rusted bolt surfaces.

Jan 1, 2003

By H. N. Maleki

This paper presents a field evaluation of six tailgate secondary support systems, with the objective of optimizing support efficiency for maintaining open gate roads. Support systems consisted of a combination of three wooden crib configurations, with either tension rebars or truss bolts. The effectiveness of the support systems was evaluated through measurements of ground movements, support load, and observations along 2000 linear ft of a tailgate. It was concluded that floor heave, crib width to height ratio, cribbing pattern, and support spacing have significant impact on tailgate stability and access after the passage of the first longwall face. Guidelines were suggested for selection of secondary support for other applications.

Jan 1, 1986

By Brian G. D. Smart

A scheme is presented whereby the complexities of design and operation of a hydraulically powered coalmine support are modelled using the finite element method. This enables predictions to be made of the interaction of the support with its environment in a variety of operating conditions. The model is a two dimensional representation. The modelling scheme was applied in two case studies. In the first, the performance of a four leg support was uprated by increasing the front leg force. The finite element model enabled changes in overall support performance to be verified. In the second case study, the change in lateral force developed by a two leg support was assessed with changes in support operating height and floor foundation stiffness. The modelling scheme is capable of further development with the possibility of extending the model into three dimensions and the addition of control elements that would enable an actual mining sequence to be represented.

Jan 1, 1992

By Fred Leighton

Outbursts, or the sudden and sometimes catastrophic expulsion of coal and gas into the working area of a coal mine, are a little understood and growing problem. The AE/MS (Acoustic Emission/Microseismic), or rock talk, activity prior to and associated with several outbursts has been recorded using ultrasonic and micro- seismic equipment and has been analyzed by the Bureau of Mines. Analysis of these data indicates that outbursts are comprised of several failures in rapid succession and that anomalous AE/MS data suitable for providing failure warning are generated 15 to 45 minutes prior to the failure. This paper discusses the techniques for recording and analyzing these data and presents sane case histories.

Jan 1, 1982

By Kevin M. Connor, O&apos

An example application is presented in which Time Domain Reflectometry (TDR) was utilized to monitor roof strata movements during pillar extraction in a potash mine. The study was initiated when Western Ag-Minerals decided to implement secondary mining of pillars in order to extend the life of their Nash Draw Mine. A prototype operation was conducted in one mine panel to assess mining equipment and procedures, and to determine if ground control problems would develop. An instrumentation array was installed by personnel from New Mexico Tech and Western Ag to monitor strata movements, changes in pillar stress and surface subsidence, and these data are being analyzed by the Bureau of Mines. This paper is limited to a discussion of roof-floor convergence and roof strata movement to illustrate the application of TDR to ground control. Plots are presented which demonstrate the capability of distinguishing location, magnitude and mode of rock movement using TDR to interrogate coaxial cables grouted into holes drilled in the roof.

Jan 1, 1990

By M. E. Duncan Fama

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface modelling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model predicted the fender would suffer considerably more deformation and strain.

Jan 1, 1992

By Ismet Canbulat

The cut out distance in the continuous miner sections in South African collieries is limited to 12 m. However, this distance can be extended to 24 m by the permission of the Department of Mineral and Energy (DME). This paper investigates the risk of roof Calls associated with the extended cut out distances permitted by the DME. Extensive underground experiments have been conducted using sonic probe extensometer under various geological conditions to identify the effect of cutting distance and tinge on the stability of the workings and the performance of the support. The results showed that that the most critical parameter with respect to ground control aspects of extended cut out distance is the bord width, which determines the amount of deformation that will take place in the roof. This was confirmed by the numerical modelling. The results also showed that a significant portion of the maximum deformation in the roof takes place before the ratio of cut out distance to bord width exceeds two. This indicates that once the face is extended more than twice the bord width, the roof will stabilise, assuming that no geological discontinuity is present and that there will be no further geometrical changes in the area as a result of for example the development of an intersection.

Jan 1, 2000