Search Documents

By Andre Vervoort

The roof in coal room and pillar panels is normally stratified and can be thought of as beams or plates supported by the pillar sides in the roadways and by pillar corners in the intersections Underground measurements showed the effect of the face advance on the additional total movement of the roof skin and on the relative movement between various layers in the roof. The latter consists of the opening of bedding planes and of the lateral sliding of layers over one another. Both phenomena increase locally the axial load along full column anchors. Four models have been used to come to a better understanding of the roof behavior: a beam either clamped above the pillar side or laying on the pillar sides and a three-dimensional boundary clement model with and without bedding planes. The shape ref the curvature of the roof deflection is host approached by a clamped beam: the other models overestimate the movement at the sides. The largest roof deflection for a given Young's modulus is estimated by the model incorporating bedding planes. This model estimates that the bed separation occurs close to the face (within the first meter) and within 0.2 m of the sidewalk. In some simulations, openings are even recorded just ahead of the face. Further underground measurements should focus on these findings, as the effectiveness of the support is directly related to the amount of bed separation and sliding, which have occurred prior to the support installation and which still cart occur abler installation.

Jan 1, 2000

By Thomas Barczak

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water¬to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water¬solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

Jan 1, 2003

By James Arthur

In deep coal mining the support of the underground roadway is fundamental and without knowledge of the mechanics of ground control a mine is unlikely to be operating safely and efficiently. It is therefore important for the support system to be designed sat¬isfactorily for the size of the excavation required and to do so an understanding of the behaviour of the surrounding strata is re¬quired. Over the last 15 years there has been a major change in the industry and the support systems adopted. The industry has been privatised, legislation has been updated, a comprehensive research programme has been carried out and guidance docu¬ments produced. The paper will show how privatisation has not allowed support standards to deteriorate, highlight research, the legislation and guidance documents updated and how this has led to a reduction in accidents and falls of ground..

Jan 1, 2002

By Edward McHugh

While less than 1% of reported accidents are associated with slope stability problems. slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technol¬ogies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyperspectral imager were conducted to assess its value for improving geologic maps of poten¬tially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized moni¬toring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

Jan 1, 2002

By Xun Luo

In this paper we report on the use of microseismic monitoring techniques to investigate the fracturing process associated with longwall mining. The study was carried out at three mines in Australia and concentrated on some major concerns of the mines, such as failure patterns and growth rate associated with mining progress, their implications to water ingress and gas emissions, caving processes in the goaf and precursors of roof falls. The results have shown that a zone of shear fracturing has occurred further ahead of the longwall face than predicted using conventional longwall geomechanics theory. Failure patterns in the roof and floor vary from mine to mine and this appears to be dominated by geological structures. The reaction of faults, the formation of fractures which allow gas emissions and precursors roof falls have also observed. Results from this work have opened up new understanding of longwall caving processes and proved that microseismic monitoring is a very useful technique for studies of longwall geomechanics and hazard controls.

Jan 1, 1998

By K. Y. Haramy

Deep coal mines with strong roof and floor strata frequently encounter face and rib bursts. The burst problem becomes more severe with increased depth. While the exact causes of bursts are often difficult to determine, localized high stress zones are common to their occurrence. This Bureau of Mines report describes a study at a mine using longwall systems that experienced both face and floor bursts. The study correlates shield loading, entry closure, and forward abutment pressure increases to observed burst occurrences. The results indicate that strong roof strata that overhang behind the longwall supports create additional abutment stress. When caving lags behind the face and the abutment zone does not advance ahead of the face during mining, stresses on the face may increase to a critical level, resulting in a burst. The critical level occurs when the stress in the abutment zone exceeds the ability of the coal and/or adjacent strata to store strain energy. Caving characteristics may be improved by inducing fractures in the roof or by providing sufficient support resistance to shear the roof. Data analysis of a major burst indicated a dramatic increase in floor heave, with a maximum occurring 80 to 100 ft inby the face, and a lag in the cave line behind the face supports. Analysis of the effects of caving characteristics and floor heave on burst occurrences is presented.

Jan 1, 1987

By William Monaghan

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH's Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

Jan 1, 2004

By A. W. Khair

This paper presents an analysis of ground movements recorded from longwall operations in the Northern Appalachian region in West Virginia. The site chosen for the investigation was selected due to varying heights of overburden and topography and was instrumented for both surface and subsurface measurements. The instrumentation areas consisted of two panels covering various sections with unique geologic and topographic features. Instrumentation included surveying monuments and shallow boreholes using an inclinometer for measuring horizontal strata displacements. Vertical strata deformation was monitored utilizing a unique design of the mechanical grouting method. Full length borehole profile extension was measured using Sondex displacement rings in the inclinometer installation. Subsurface displacements, i. e. caving zone, fractured zone, and highly deformed non-fractured zone were identified. The nature of surface disturbances with respect to varying geologic settings were compared, and an attempt was made to simulate final strata caving and bed separation using finite element analysis.

Jan 1, 1987

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By Kevin Andrews, Scott Nelson, Terry Hamrick

"In the process of Geologic Hazard Mapping (GHM) for underground coal mining, geologists evaluate the effects of various geologic and geotechnical conditions to assist with optimization of mine productivity and with selection of more favorable areas for future development. The methodology involves correlation of multiple geologic factors (such as overburden depth, proximity to sandstone channels, and areas with weak immediate roof strata) with conditions encountered during mining (roof falls, floor heave, pillar spalling, etc.). Such studies yield maps that identify areas where mining is likely to be difficult and allow mining engineers to foresee favorable and unfavorable mining areas when planning new or expanding mines. To expand the benefits of GHM, work has been done to correlate geologic factors with room-and-pillar mining advance rates. Average mining advance rates are mapped and then correlated to different areas, as characterized by GHM. This process exposes the geological characteristics that have a material impact on mining rates of advance, improving the rates of advance into future mining areas with similar geological conditions. The final result of the work allows mine planners to not only design the mine qualitatively accounting for areas of unfavorable conditions, but also allows the mine planner to more accurately apply rates of advance for mine timing and production sequencing. The use of GHM to predict mining advance rates in unmined areas enhances the benefits of traditional hazard mapping and provides quantitative data that can be incorporated into mine sequencing models.INTRODUCTIONThe role of a geologist in the coal mining industry has evolved significantly over the last 30 to 40 years. Geologic Hazard Mapping (GHM) mapping for coal mines began in the late 1970s and early 1980s (Chase, Newman, and Rusnak, 2006). Since its beginnings, the GHM process has evolved significantly and continues to take on new levels of sophistication. Numerous case studies of GHM application to predict future mining conditions exist in the literature. For example, Artrip, Nelson, and Newman (1993), documents the geotechnical characterization of roof and floor for mining in the Imboden Seam in Virginia where previous mining efforts had been abandoned due to adverse mining conditions. In addition, Keim and Miller (1999) summarize evaluation of geological influences on a longwall mine in West Virginia. In both examples, significant geotechnical and geological information was available, including the opportunity to compare predicted mining conditions against actual conditions as mining progressed."

Jan 1, 2018

By Kent D. Mctyer

Mining commenced at Tasman Mine in late 2006. The current method of mining is bord and pillar using continuous minerbolters and shuttle cars for first workings and secondary extraction using mobile roof supports. The two stage process was chosen to accommodate irregularly shaped coal deposits, allowing adjustments to be made to extraction ratios for better management of subsidence and to maximize the efficiency of the operation. Following the completion of the first three full/partial extraction panels, the mining method was changed due to variable caving. Another partial extraction method, referred to as the Duncan Method was adopted; it involves stripping the developed square pillars on four-sides on retreat to leave a load-bearing remnant coal pillar. The system of partial extraction has been successful in meeting safety, productivity, and subsidence targets.

Jan 1, 2011

A two-dimensional time-dependent analysis of a overburden-coal pillar-weak floor strata interaction problem is presented as a beam model consisting of a composite roof beam resting on multiple elastic foundations (pillars) underlain by a composite rock mass representing immediate floor strata. Several different material models may be considered for the immediate floor strata. The analysis can include all openings and pillars in a panel and permits bed separations in the roof composite beam. The model has enabled identification of the relative significance of different geometric and mechanical behavior parameters which govern the system. The paper presents the theoretical background for the model as well as its application to a mine in Illinois where surface and underground geotechnical observations have been conducted over the last two years.

Jan 1, 1988

By S. M. Matthews

The magnitude and orientation of the in situ stressfield has been determined as a key factor in controlling the stability of openings for both coal mine development and extraction. Monitoring of roadway and pillar behaviour in conjunction with numerical analysis has identified specific stress control measures that have been successfully applied to improve productivity in underground coal mining operations. The influence of the major horizontal stressfield on the stability of openings has been identified at a wide range of sites including mines in Australia, Britain, the USA, New Zealand and Japan. Stress mapping, stress measurement and stress monitoring techniques have been applied to define the in situ stress regime and, together with the correlation of measurements of rock deformation and rock reinforcement behaviour, has enabled appropriate stress control measures to be developed. Stress control measures for development headings have required the selection of roadway orientation, roadway sequencing, reinforcement density and pillar size. The monitoring of behaviour at a range of trial sites has confirmed significant improvements in development stability. Stress control measures for longwall extraction have required rational selection of longwall orientation and extraction direction. Where a mine layout design incorporating the optimum longwall layout design has not been possible, the use of sacrificial roadways has been successfully applied to protect key roadways from stress concentration effects. Comprehensive in situ monitoring of behaviour has been carried out to confirm the mechanisms involved.

Jan 1, 1992

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By Yunqing Zhang

Roof failure occurs much more frequently at intersections than entries and crosscuts. Using a commercial finite element package, four-way and three-way intersections reinforced with the tensioned bolts are modeled. The 3-D model considers bolt pre-tension, bolt installation procedure, bedding planes and in-situ horizontal stresses. The modeling results from both four-way and three-way intersections are analyzed with regard to the intersection stability. The mechanisms of tensioned bolting at the intersections are investigated and some tensioned bolting guidelines for intersections are given. Based on this study, a better way to enhance intersection stability is to use longer bolts than entries or crosscuts and increase the bolt density near the intersection corners.

Jan 1, 2003

By Klaus-Dieter Beck

RAG American Coal Holding, Inc. affiliates operate two longwall mines in the Pittsburg seam in Pennsylvania, the Cumberland mine and the Emerald mine. A unique situation in longwall operation occurred at these mines as the mining activities reached the property boundary between the two mines. The retreat direction in the longwall panel in Cumberland mine is West-to-East while in Emerald mine, it is East-to-West. This unique condition required an adequate design for barrier pillar between the two mines to minimizing the mutual effects of longwall retreat when both longwall faces met and an adequate roof control plan for gateroads. Field studies that involved mainly roof-to-floor convergence monitoring were conducted to assess the effectiveness of the employed barrier pillar in isolating the mutual effect of longwall retreat. Three-dimensional finite element numerical modeling was used to evaluate the gateroad roof and pillar stability. The modeling was conducted such that it duplicated the actual mining process as realistically as possible. The modeling results predicted that the employed barrier pillar and the roof control plan would ensure stable gateroad systems in both mines during and after the two longwall faces met. The prediction was confirmed because mining operations in the two longwall panels were completed without any noticeable ground control problems.

Jan 1, 2004

By Jinsheng Chen

The major functions of longwall headgate entries are to provide access ways to the outby submains or mains for coal transportation and to the longwall face for fresh air and for transporting men and material during longwall operations. Any roof control problems such as cutter roofs or roof falls in the outby headgate entries could result in significant production delays to the longwall face and may be a threat to miners' safety Under a thinly laminated immediate roof and a high horizontal stress field, even a longwall headgate entry that has an angle of less than 45 degree to the maximum horizontal stress may experience roof deterioration in the outby headgate if the longwall panel mining sequence and retreat direction are not properly considered. This paper attempts to analyze the causes of the roof control problems experienced in the longwall gate entries at our Cumberland and Emerald mines in Pennsylvania and to determine the optimal longwall panel mining sequence and retreat direction for the future mining area at Cumberland

Jan 1, 1998

By David C. Johnson

Coal mining in Illinois has resulted in many structures being exposed to subsidence damage. Damage mitigation techniques (DMT) applied in the foundation design/construction have proven successful in minimizing damage in several test cases. To determine the practicality of these techniques, the Costs of their application are investigated. The AMT costs are compared to foundation and total house costs for various classes and sizes of houses. An economical and effective subsidence resistant foundation construction is proposed.

Jan 1, 1993

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997