Search Documents

By Jessica M. Wempen, William G. Pariseau, Michael K. McCarter

"Quantitative analysis of mine-wide subsidence at the kilometer scale and details of stress distribution about an advancing longwall face are estimated using an adaptation of the finite element method. The method is well suited to the tasks at hand. For greater realism, variability of strata properties is taken into account as are the effects of joints and cleats on elastic moduli and strengths. Evolution of pillar stress and entry closure remote from the face is readily quantified in a series of analyses that simulate face advance. Computed results compare favorably with the evolution of closure measurements about an instrumented pillar in a two-entry headgate. The appropriateness of the finite element method is confirmed. This method is based on first principles that avoid empirical schemes of uncertain applicability and numerical models “calibrated” by fitting computer output to mine measurements.INTRODUCTIONMine-induced seismicity is intimately related to strata mechanics associated with longwall coal mining and room and pillar mining, as well. Strata deformed beyond an elastic limit often tend to fail rapidly by brittle fracture and, thus, to emit acoustic signals in the form of elastic waves. Understanding the induced seismicity in coal mining offers the potential for early warning of hazardous conditions. Many years of experience with seismic phenomena associated with hardrock mining suggest considerable complexity should be expected. However, recent coal mine studies (Pariseau, 2014; Pariseau, 2015; Pariseau and McCarter, 2015; Pariseau and McCarter, 2016) have shown high correlations of seismicity with element failures in finite element simulations. The main lesson learned from these studies is one elaborated by Iannacchione et al (2005); deviation from normal activity is an early warning of ground control difficulty. For example, an abrupt increase in seismic event rate, or equivalently, an increase in element failure in finite element simulation of panel advance, is a cautionary indication for ground control. Present and past study results demonstrate the effectiveness of finite element simulations for mine design and early detection of potential ground control issues."

Jan 1, 2018

By Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non¬fatal injuries to human workers. A commonly used technique is to devise an "incident prevention plan", which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident - in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of "events of interest". This paper introduces a novel technique - "Taxonomic Analysis", which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984¬1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

Jan 1, 2003

By Kun Li, Shuaishua Yue, Huigui Li, Yuan Ruifu, Yongxiang Xu, Huamin Li

"Coal seams in Tashan Mine of Datong Coal Group in China average 49.2 ft (15m) thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 12.5 ft (3.8m) and the top coal caving height was 36.7 ft (11.2m). The gateroad pillar between panels was 124.6 ft (38m). During retreat mining, serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore, pillarless mining was experimented.Using numerical modeling and comparative study of cases of similar mining condition, it was decided to employ a 19.7 ft (6m) wide pillar, rather than the previous 124.6 ft (38m) wide pillar. Support system for the gateroads was designed and implemented. During gateroad development, pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion.Since the development of gateroad has just completed, and retreat mining has not begun, the effectiveness of the proposed methods is unknown at this point. However, monitoring will continue until after mining. The results will be published in a separate paper.INTRODUCTIONGeneral descriptionTashan mine is located about 15 Km south of the city of Datong, Shanxi province, China (aure 1). The 2014 raw coal production was 25 million mt."

Jan 1, 2015

By E. Yasar

This paper describes the use of the sand and plaster physical modelling technique to investigate the deformation around mine roadways using a variety of support methods in a particular form of stress field. The characteristics and conditions of coal measures rock were considered prior to the preparation of the models and the insertion of support The investigation has clearly shown how floor lift, roof failure and sidewall movements of mine roadways in laminated weak rock conditions gradually develops as a result of the increase in the stress and, also, how it is related to the level of support used.

Jan 1, 1995

By Y. Luo

This paper presents a number of mathematical models for predicting the different phases of the complete surface subsidence process associated with underground longwall mining. A computer program developed based on the mathematical models is briefly introduced.

Jan 1, 1992

By R. Fraher

Hazard analysis utilizes interaction mechanisms in combination with geologic, structural and mining conditions to delineate areas of potential damage in seams subject to interaction. Using characterizations of conditions peculiar to multi-seam mining, such as innerburden thickness, geology and structures, initial interaction contour maps can be constructed. Geologic hazard analysis is then carried out on roof, pillar and floor conditions in the affected seam using lower seam rock properties and layout geometries in the overlying seam. Either safety factors or damage ratings can then be developed representing degree of hazard in the lower seam. The final hazard map shows both the aerial extent and magnitude of potential damage from interaction.

Jan 1, 1992

Numerical simulation for microseismicity due to mining at one of the collieries in Australia was carried out and the results were compared to the observed microscismicity. 3-D Stress analysis showed stress concentration on the edges of the mined areas and on the coal pillars- The stress concentration ahead of the coal face was biased to the tailgate. This is similar to the observed distribution of microseismic events. Stress reduction above and below the mined area was seen. Tensile stress was observed mainly above the mined area. It was realized that compressive failure due to nearly vertical maximum principal stress and nearly horizontal minimum principal stress in retreat direction (NS) might occur ahead of the face. Tensile failure due to nearly vertical minimum principal stress above the mined area was expected. Compressive failure due to nearly horizontal maximum principal stress in EW direction and nearly vertical minimum principal stress above and below the mined area were also expected.

Jan 1, 2001

By Michael Kelly

Longwall mining is the principal method of underground coal mining in Australia, with 70 million tonnes being produced by longwall mines in 1999. However, the mechanisms that control longwall geomechanics are still not clearly understood resulting in stoppages costing several hundred million dollars per annum The CSIRO has been investigating longwall geomechanics with consultant groups and minesites through several ACARP supported projects since 1994. The research has aimed to improve longwall support design and control methods by defining strata failure mechanisms and their occurrence about underground extraction panels, It also aimed to develop better predictive tools bur a broad range of underground environments. As a result of site studies at more than 8 locations some of the aspects that have been touted to control longwall geomechanics, especially from a 3D aspect are highlighted. These aspects include stress controls, geometry, faulting, depth. longwall width and changes in lithology.

Jan 1, 2000

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By Satyendra K. Singh

If the extraction is beneath massive roof strata, the roof tends to 'bridge' across large spans without failing, the caving behaviour is complex and irregular. Understandably, these give rise to many geotechnical problems with safety implications and involving sometime huge direct and indirect costs. Only two important problems, 'feather-edging' in pillar mining and `severe periodic weighting' in longwalling, are discussed in this paper in the background of geomechanics investigations in Australia at Blue Mountain Colliery and in South Bulga Colliery respectively. `Feather edging'- a major source of injury and fatal accidents in Australia and South Africa in such situations, refers to a phenomenon where the roof, at the goat edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. The results of the first comprehensive, monitored trial in an Australian pillar extraction coal mine, suggests how the roof falls into feather-edging caving (generally) because of multiple shear-planes (interpreted) and how it may be alleviated. Because of complex fracturing behaviour of massive roof strata, periodic weighting at a longwall face is certain to manifest itself as 'yielding supports', heavy conditions', rapid convergence and in the worst case, as a cause of face stoppage. After briefly discussing the programme of instrumentation (in a chain-pillar and over the would-be goal) and results, this paper attempts to improve mechanistic understanding of the related geotechnical issues associated with the weighting behaviour and aims at establishing a 'threshold' value of weighting severity index (suggesting intensity of periodic weighting) with an objective to optimise operational controls before mining through potential (future) weighting areas.

Jan 1, 2000

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By Phillip E. Gramlich

Through extensive practical experience and multiple studies, tensioned roof control systems have proven beneficial in difficult mining conditions. Due to increased mining of less desirable seams, tensioned roof control systems have claimed a progressively larger share of the total number of roof bolts installed in the US coal industry. Each tensioned roof control system has its benefits, but also has problems concerning cost, cycle time, stress concentration, load retention, and protrusion into the mine opening. For example, resin-assisted mechanically anchored bolts (also known as resin point anchor bolts) have a fast cycle time and the potential for high tension loading, but the stress from the mechanical shell is concentrated in a small area and can create concerns with certain roof structures (Zhang and Peng, 2001). Resin point anchor bolts can be difficult to fully grout. The cost of resin point anchor bolts can be an issue; a two-piece resin point anchor bolt has a large number of parts (10) and manufacturing steps (9), adding to its higher cost. Tension rebar bolts can achieve high loads and are easier to fully grout but have longer cycle times. In addition, a high percentage of the installed load can ?bleed off? if the resin mixing time or the ?hold time? before tensioning is short-circuited. Tension rebar bolts can be notorious for protruding into the mine opening, creating an obstruction for man and machine (Figure 1), in particular, with reduced mining heights. A new tensioned roof control system has been developed that doesn?t have moving parts, is cost effective, provides fast cycle times, has a low profile, and is simple t install.

Jan 1, 2014

By M. W. Fabjanczyk

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By Jesse L. Craft

Field investigation of surface subsidence events associated with both active and abandoned underground coal mines in the United States has established criteria that enable the prediction and classification of mine-related subsidence. The key was establishing the role of geology in all types of subsidence and the recognition of beam subsidence in specific geologic settings. The classification is based on overburden thickness, variations in stratigraphy, topography and mine plan. Types of subsidence are Pit, Room, Sag, and Beam. Pit subsidence is associated with three geologic settings: shale overburden, seasonally wet unconsolidated overburden, and perched water table in unconsolidated overburden. Room subsidence occurs where the roof across the width of the room fails to the surface and a shallow depression develops. Sag subsidence develops where the pillars are failing in conjunction with roof failure. Overburden thickness is generally greater than 150 feet. Beam subsidence can occur in all terrains. It is associated with retreat mining and room and pillar mining where pillar crushing or pillar compression has taken place and barriers are left inplace. They occur as beam arch or one-sided beam subsidence. Beam arch failure occurs where mining has taken place on both sides of a coal barrier. One-sided beam failure is associated with retreat mining moving from a barrier towards the entry in hilly topography. This type of subsidence occurs where a hard, thick, rock unit is acting as a bridge supporting the overburden and outcrops on the hill side.

Jan 1, 1992

By Joe Wickline, Mark A. Van Dyke, Wen H. Su

"Geological factors and mine design contribute to mining-induced seismic activity, and this is especially true in longwall mining. Massive rock units are a key cause of seismic activity due to catastrophic failures that release large amounts of energy. Other factors, such as overburden depth, panel design, pillar design, rock strength, and proximity of the massive rock unit to the coal seam, all have a role in the potential and size of a seismic event. A recent seismic event was recorded by a deep longwall mine in Virginia at 3.7ML on the local magnitude scale and 3.4 MMS by the United States Geological Survey (USGS) in July 2016, which had no impact on the mining operations. Further investigations by NIOSH and Coronado Coal researchers have shown that this event was associated with geological features that have also been associated with other, similar seismic events in Virginia. Detailed mapping and geological exploration in the mining area has made it possible to forecast possible locations for future seismic activity. In order to use the geology as a forecaster of mining-induced seismic events and the energy potential, two primary components are needed. The first component is a long history of recorded seismic events with accurately plotted locations. The second component is a high density of geologic data within the mining area. In this case, 181 events of 1.0ML or greater were recorded by the mine’s seismic network between January, 2009, and October, 2016. Within the mining area, 897 geophysical logs were analyzed from gas wells, 224 core holes were drilled and logged, and 1,031 fiberscope holes were examined by mine geologists. From this information, it was found that overburden thickness, sandstone thickness, and sandstone quality contributed greatly to seismic locations. After analyzing the data, a pattern became apparent indicating that the majority of seismic events occurred under specific conditions. Three maps were created using MineScape geological mapping software. MineScape deploys an interpolator known as FEM (finite element method) and is based on a series of gridded triangles to forecast the probability and magnitude of an event if a particular panel were to be mined. The forecast maps have shown accuracy of within 74%–89% when compared to the recorded 181 events that were 1.0 ML or greater when considering three major geological criteria of overburden thickness of 1900 feet or greater, 20 to 40 feet of sandstone within 50 feet of the Pocahontas number 3 seam, and a longwall caving height of 15 feet or less."

Jan 1, 2017

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993