Search Documents

By J. Torma-Krajewski, C. Hipes

Many mining companies apply ergonomic principles, but it is done either informally and/or reactively. Examples of an informal approach include replacing worn equipment, such as seats, with models that have ergonomic features, or modifying tasks to eliminate safety hazards that will also reduce risk factor exposures that may result in musculoskeletal disorders (MSDs). A reactive approach is followed when modifying a task/equipment after an MSD occurs. Neither one of these approaches involves a systematic method of proactively applying ergonomic principles to actually prevent injuries or illnesses. This paper will discuss how Vulcan Materials Company applied ergonomic principles and the interventions implemented to reduce risk factor exposures.

Jan 1, 2007

By Steve Kral

President Bush’s National Energy Program and his Clear Skies Initiative both emphasize the use of coal to help meet the nation’s growing energy needs. And why not? Coal is currently responsible for more than 50 percent of the nation’s electricity generation. That fact, though, seems to be lost on policy makers, the environmental community and the public. Critics of coal advocate the increased use of renewable energy sources and the increased use of natural gas. Renewables, though, are only capable of generating a tiny fraction of the power required. Natural gas is expensive. And natural gas production cannot keep up with demand, especially given the nation’s increasing energy needs.

Jan 1, 2003

By G. T. Lineberry

Underground mine development begins with the positive investment decision to mine and ends with the inception of full-scale exploitation. It incorporates all activities, personnel, and equipment required for creation of underground access to a mineral deposit. Because of the depletion of near-surface mineral resources, the reduced mobility of large surface mining equipment, increasingly stringent environmental constraints, and the introduction of promising innovations to rock penetration and rock excavating equipment (e.g., continuous miners, rock borers), under-ground mining is projected to account for an increased share of worldwide mineral production in the foreseeable future. Without proper engineering during the mine development phase, failure of the underground mining project is axiomatic. A frustration attendant to coverage of the complex area of underground mine development lies not only with the need for treatment of the many disparate specialties within the area but even with the lack of systematization of these specialties in what is recognized as a vital precursor to successful mining. Section17 offers insights into (1) the basic principles of the planning and design process, including baseline assessment, reserve determination, premine planning, and subsystem design (Chapter17.1); (2) equipment selection and sizing, with emphasis on exca-

Jan 1, 2008

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

By David Belknap, Clay Haynes, David Egger

Rehabilitation challenges were met nearly two months ahead of contract schedule for the Design-Build, Fast Track Scituate Aqueduct & Tunnel project in Cranston, Rhode Island. The aqueduct and tunnel were built in the 1920s and consisted of three sections—a 2.3 m diameter reinforced concrete section that extends approximately305 m before it transitions to a horseshoe-shaped 2.3 m wide by 2.1 m high cast-in-place concrete tunnel that continues for approximately 5.3 km until it transitions back to a 2.3 m circular section that extends approximately 1.9 km to the end of this project. Major repairs were required to assure sustained operation of this water supply tunnel.

Jan 1, 2005

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. There are many standards available across multiple industries that prescribe emission limits and test methods for electronic devices. Due to the unique environment of an underground mine, it may not be enough to simply adopt a standard from another industry to mining. A literature review has been conducted, and an overview of EMI standards in other industries will be provided in this paper. Also, an example of how a standard can be applied to mining equipment is presented. Finally, recommendations on standards which could potentially be applied to mining will also be included. This work will inform the mining industry of EMI standards in other industries so that mine workers and technology manufacturers have guidance of the steps that can be taken to investigate and reduce the impact of electromagnetic interference and potentially work toward electromagnetic compatibility. The findings and research involved in this effort can also be used to explore the need to develop mining-specific EMI recommendations and standards.

Nov 25, 2021

By Desiree Willis

Disc cutters have determined excavation rates of rock tunneling projects for more than 50 years. First developed in 1956 by James S. Robbins, disc cutters (then 279 mm or 11 in. in diameter) were used to bore limestone of 190 MPa (27,500 psi) unconfined compressive strength (UCS) and were loaded with 7.12 t (15,700 lbs) each. Modern cutters have reached up to 508 mm (20 in.) in diameter and are typically loaded with up to 31.7 t (70,000 lb) to economically bore through the hardest of rock up to plus 400 MPa (60,000 psi) UCS. New developments, such as larger cutter diameters, are geared to increasing the bearing capacity and wear life of the cutting structure. This, in turn, increases cutter life, cutter load and cutter penetration. Disc cutters have also been re-designed on a small scale for use in hard-rock utility installations. Additional variables also affect the three factors, including cutter spacing on the cutterhead, cutterhead diameter and cutter materials.

Jan 1, 2007

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

A practical core-based method for estimating in situ stress was tested using 360° measurements of rock core diameter in a laboratory setting. In several mining districts across West Virginia, rock cores were recovered from exploration core holes and oriented using an acoustic televiewer (ATV) summary log. Measurements of diametral variation were performed at 0.1-foot depth intervals using a benchtop device comprised of a pair of diametrically opposed contact digital indicator gauges working in tandem. The diametral profiles were evaluated to determine strain direction and strain magnitude. Stress magnitudes were calculated when values for Young’s modulus, and Poisson’s ratio were available. Stress direction results are compared to other stress determination methods, including downhole overcores, drilling-induced fractures, and borehole breakouts. The testing and analytical methods used are similar to the diametrical core deformation analysis (DCDA) method (Ito, Funato, and Shono, 2012), but with a number of important improvements.

Jan 7, 2020

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By V. K. Kollipara

Air flow patterns in the face area of a room-and-pillar mining are critical for understanding the dust dispersion characteristics and for developing engineering controls. SIUC has previously performed a CFD study to analyze the airflow patterns in the face area when continuous miner is making a straight cut. Results from this study identified low air velocity and re-circulation zones in the face area and illustrated the significance of line curtain, and scrubber operation on the air flow patterns. This paper discusses similar analyses when continuous miner is making a right turn cut as it is considered to be the dustiest cut among all the cuts made to advance an entry through a crosscut. This paper presents results for box-cut development for a right hand turn x-cut. This paper also addresses line curtain advance and air leakage through the curtain on the airflow patterns in the face area for such a cut. Low air velocity and recirculation zones were identified by analyzing the velocity vectors.

Jan 1, 2012

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

By E. A. Adey, C. Baciu, P. Whitbread-Abrutat, M. Varul, T. Ejdemo, R. K. Shail, F. Wall

Responsible mining requires stakeholder engagement throughout all operational stages and after mine closure. By assessing the current and anticipated future socio-economic and environmental impacts, a company can maximise the positive impacts they can have on a community, whilst minimising any negative impacts. Despite the current emphasis on companies maintaining effective stakeholder relations to gain their ‘social license’ to operate, findings of the present study reveal a wide variation in community expectations, with different degrees of ‘acceptability’ evident across seven sites in Romania (Rosia Montana), Sweden (Kristineberg), the United Kingdom (Cornwall), Bosnia Herzegovina (Vihovici) and Russia (Karabash, Gay and Mednogorsk). These variations reflect the current status of mining within a community, as well as its socio-economic background and the nature of existing engagement with mining companies already operating in the region.

Jan 1, 2011

By Steve Kral

The mining industry is no stranger to hard times. Throughout its history, the industry has faced the ups and downs of commodity prices, difficult-to-mine-and-process ore bodies, labor issues and other problems. Throughout it all, though, the mining industry continues to provide the materials needed for society —even in the face of attacks by those who seek to cripple the industry or have it go away. The reason the mining industry survives, of course, is that mankind requires the products the industry produces. And, in recent decades, the industry has developed new technologies and improved on existing ones to produce those products in environmentally sound ways. At the same time, the economic benefits have been enormous to communities throughout the world where mining takes place.

Jan 1, 2002

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

By Youngtak Ko, Wonnyon Kim

Korean contract Mn-nodule field in the NE equatorial Pacific is composed of seven sectors showing average water depths of 4,513 - 5,025 m. Of the various factors controlling the property of Mn-nodules, water depth has a potential linkage to chemical composition, shape and abundance of nodules. To clarify such a possibility, we review more than 20 years of research data in one of the northern sectors (hereafter KR1) where there is a marked contrast in water depth. High-resolution seabed mapping clearly separates a northern part from a deeper southern part, cutting across the middle of the KR1. In terms of nodule occurrence, manganese nodules in the deeper north are comparatively larger (2-4 cm) with rough surface (t-type) and discoidal shape (D-type), while those in the south are generally small (<2 cm) with smooth surface (s-type) and irregular shape (Itype). In addition, the nodules in the north have higher metal contents including Cu, Mn and Ni. Such connections of water depths to nodule occurrence and metal contents are commonly observed in the Korea licensed Pacific nodule fields. However, the relation between nodule abundance, size and water depth may be a different story. In KR1, nodule abundance and size are probably controlled by morphological features especially in the north. Seamounts in the north continuously provide rock fragments as new nuclei for the nodules. As a result, the nodules can not grow larger than 2 cm and show the shapes of newly formed nodules (i.e., smooth surface and irregular shapes). Such an interpretation is supported by anomalously high backscattered intensities in the side-scan sonar image map of the north, which possibly reflects a younger generation of magmatic activity.

Sep 1, 2014

By C. G. Hunkin

In situ, or in-place leaching is concerned with the extraction of metals from natural mineral disseminations without removal from their geologic location which, in many cases, amounts to the reversal of the deposition process accompanied by a presumed increase in velocity of the processes, if the project is to be profitable. Solution mining processes involve removal of minerals such as sulfur, common salt, and potash, generally leaving cavernous voids, in contrast to in situ leaching which term is applied to the selective dissolution of a mineral from its gangue without sensible disturbance of the formation. Where such a process can be operated, the advantages are manifold and have been so recognized by miners from the earliest days of mining. Recent technological developments have encouraged a reassessment of the status of in situ leaching, and it now appears possible to extend the application of the method from a few isolated special situations to many uranium and copper deposits. Anaconda&apos;s interest in the techniques stems from long experience with vat and heap leaching, &apos;dump leaching, and natural leach activities associated with several established mines. Increasing activity through-out the industry has been noted, particularly in leaching low grade pillars and the peripheral zones of operating mines, often by the introduction of leach solutions via boreholes drilled from surface. Reactivation of dormant mines] using similar techniques has been successful. Over the long term, environmental improvement activity will lead to excess sulfuric acid production, even to a disposal problem. The cost of leach solutions and reagents must be reexamined in this light. The mineral industry now classifies as uneconomic deposits of readily soluole minerals whose potential value, on a per acre basis, may De several times that of many currently profitable oil field reser-

Jan 1, 1971

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008