Search Documents

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at temperatures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Formation changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite. © 2007 Elsevier Inc. All rights reserved. Keywords: Biwabik Iron Formation; Duluth Complex; Mineralogy

Jan 1, 2007

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By G. E. S. Valadao, J. D. Miller, C. L. Lin

Filtration is an important solid liquid separation technology employed widely in the mineral processing industries. The effectiveness of the filtration operation can be influenced by numerous variables, related to the particulate phase, the slurry rheology and the equipment. The classical approach for analysis is based on Darcy's law. Knowledge of the cake poremicro structure and its correlation to macroscopic cake properties is required to model the filtration operation from a fundamental point of view. Since cake formation seems to occur randomly, a 3D Monte Carlo method was used to simulate cake formation. The configuration for simulation was a space with width of 500 m, length of 500 m and height of 4000 m. Size distributions of five different industrial products whose particle size distributions follow the Rosin Rammler distribution function were used. The particle shape was assumed to be spherical. The simulated cake structures were described in terms of volume porosity (volume of pore space per unit volume of cake) and surface porosity (area of pore space per unit area of a cross section). The results indicate: 1) it is possible to simulate 3D packing, which mimics cake structure, using the Monte Carlo method,2) segregation phenomena occurs during simulated cake formation, 3) the values of calculated porosity for simulated samples B, C, D, and E were lower than those determined for corresponding industrial products Br, Cr, Dr, and Er, and 4)some structures of simulated samples seem to correlate with laboratory leaf test data obtained for different products from plant operations.

Jan 1, 1999

By T. E. Bernard

Occupying a refuge alternative (RA) is an accepted practice in mine fires and explosions when escape is not feasible. MSHA has promulgated a final rule on refuge alternatives that includes a recognition that thermal environment is an important consideration. To this end, an environmental index was specified. The question remains about how to test a refuge shelter to demonstrate that it meets the final rule. The analysis followed five activities: A. Provide an estimate of heat generated by an individual refuge alternative occupant; B. Evaluate the Steadman Apparent Temperature criterion of 95°F; C. Discuss simulations based on body temperature or skin temperature limits; D. Suggest method of simulating human heat generation during refuge occupancy; and E. Suggest alternative methodologies/criteria for evaluating heat and humidity survivability inside a refuge alternative.

Feb 27, 2013

By Klaus Rieker

Over the last 30 years Wayss & Freytag Ingenieurbau AG has gained a lot of experience in mechanized tunnelling on various major projects. During this period most important developments concerning the machine technology for EPB- and Slurry-Shields have taken place. Since the first application of a hydro shield for the Wilhelmsburg Collector project in Hamburg in the early seventies, several stages of development have led to the current state-of-the-art in mechanized tunnelling. The continuous improvement of TBM techniques allows the execution of high quality tunnelling, particularly with regard to maximum safety and efficiency. The practical experience of the construction companies is of essential importance in order to continue further development and improvement.

Jan 1, 2005

By Bernd Hagenah, Katie Theis, Cristina Lauzon, Petr Pospisil

Lidding over or tunneling existing transportation infrastructure is currently under review in several U.S. cities. The main reasons for this are the use of the created space for urban development, the reduction of noise and exhaust fumes for the residents, and, thus, a significant increase in the quality of life. The main aspects to be considered during the planning process are (1) total investment and operational costs, (2) impact of construction works on current traffic, (3) safety and fire protection, and (4) socio-environmental issues. The paper presents some basic planning principles, and experiences of recent urban highway coverages are shared.

Jun 23, 2024

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By D. Earley

High metal prices and new world trade standards and accounting for environmental liability in financial disclosures are creating markets for metals commodities that are produced using ?green technologies?. A promising "green" gold leaching system uses a polysulfide based lixiviant which is non-toxic and non-polluting. Laboratory testing has demonstrated selective gold extraction rates comparable to those of cyanide. The polysulfide lixiviant is a dilute aqueous solution which can be inexpensively produced from readily available chemical reagents and even mining wastes. The reagent system is self-buffering and maintains the optimal chemical environment for leaching. Treatment of residual leach solutions is not necessary because the lixiviant itself is not toxic, and breaks down as the system equilibrates. Simple closed system boiling is used to recover gold from process solutions. The polysulfide lixiviant can then be readily renewed and recycled back into the system, forming a closed loop system that conserves reagents and energy which minimizes operating costs. Economic projections have shown that the system can be used profitably for standard ore types and grades.

Jan 1, 2009

By G. Kosick, G. Dobby

CEET, an acronym for Comminution Economic Evaluation Tool, was jointly developed by MinnovEX Technologies Inc. and 13 major mining companies for the purpose of designing and predicting the performance of grinding circuits. It fundamentally differs from other methods by using as its’ data set a geostatistically significant population of hardness data distributed across the mine block model. Historically the characterization of an orebody for the purpose of either designing a grinding circuit or predicting the performance of an existing circuit has been done with a relatively limited number of discrete samples. In addition to power selection, shell sizing, and costing for multiple circuit options, CEET also outputs tons per hour, P80, and operating cost on every mining block for subsequent integration back into the block model. This paper will provide an overview of what CEET is and how it works.

Jan 1, 2001

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the United States. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before fi ring to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150 kt (165,000 st) of barite in 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender or weighting agent in products such as paints, plastics and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, to add weight to rubber mud flaps on trucks and to add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around X-ray units in hospitals, nuclear power plants and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses accounts for an estimated 78 kt/a (86,000 stpy) in the United States.

Jan 1, 2009

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By R. L. Virta

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans Inc., is the industrial minerals annual review editor. Abani Samal, member SME, of Pincock Allen & Holt, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock Allen & Holt, ceramics and refractories ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer Inc., construction materials. ? Jerry Gauntt, member SME, of Marston, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. ? Candace Trimble, Oil-Dri Corp. of America, specialty minerals. Their help makes possible this June industrial miner-als issue. On behalf of ME readers, the editors thank them. Ball Clay Four companies ? H.C. Spinks Clay (owned by Lhoist Group), Kentucky-Tennessee Clay (owned by Imerys Group), Old Hickory Clay, and Unimin Corp. ? mined ball clay in four states in 2008. Production, on the basis of preliminary data, was 964 kt (1.1 millon st) with an estimated value of $45.3 million. That was a 10- percent decrease in tonnage from 1.07 Mt (1.2 mil-lion st) with a value of $49.2 million that was produced in 2007. Tennessee was the leading producer state with 63 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 73 percent of production was airfloat, 16 percent was crude and 11 percent was water-slurried.

Jan 1, 2009

By Helmut Hass, Michael S. Shultz

For many tunneling, deep shaft and deep excavation projects ground freezing is one of the best if not the only technique available to create a watertight and load bearing temporary support system in soft ground conditions. When appropriate attention is given to the details of the ground freezing system design, ground freezing is a very safe method and is economically viable with competing techniques and combinations of techniques. Recent innovative uses of the technique in Europe are highlighted in this paper and compared with current uses in North America.

Jan 1, 2005

By Carlo Sampaio, Moacir Veras, Aaron Young, Carlo Petter

"Three major challenges for the mining industry are the minimization of energy use, water consumption and environmental impact. Therefore, any technique that reduces milling waste, decreases water usage and shrinks impact during mine life must be considered a major innovation in mining.To these ends, one of the most impactful developments in mining within the last 10 years has been the expanded use of high technology sensors to create preconcentrations of mine ore (Jönsson, 2014). The most common sensors used are charge-coupled device (CCD) cameras, that allow through a red, green and blue (RGB) coloring system, the separation of minerals with different colors, tones and, in many cases, with differences in brightness.More recently, the development and use of dual energy X-ray transmission (DE-XRT) to enable the separation by atomic density of the constituent minerals within a given rock has become a reality. Within this work, a rapid bibliographical review of the CCD and DE-XRT methods and examples of their usage within mining and the industrial minerals sector are presented.Sensor-based sorting in miningAutomation within mining is one of the industry’s current goals. Sensors of various kinds have been used as steps toward automation in recent years, from improving the safety and productivity of haul trucks through the use of cameras and global positioning satellites (GPS), to the divination of slope failures. Just as with other mining areas, sorting has improved dramatically and made great steps toward automation in recent years (Wotruba et al., 2014).Sensor-based sorting (SBS) uses spectromatic sensors to identify intrinsic characteristics of particles and separates them by either mechanical or pneumatic means into different product streams (Wotruba et al., 2014). SBS can be used with great effectiveness to improve gravimetric beneficiation through the selective separation or preconcentration of run of mine ores (ROM)."

Jan 1, 2015

Using mines in Canada, Boart Longyear, a leading provider of drilling services and products, has put its Stage 3 Coring Bit to the test and each time the bit has passed the test with great success. After more than a year in the field at a major mine operation in Sudbury, Canada, the Stage3 coring bit broke life records to become recognized as the most productive design in the industry. In addition to the proven advantage seen in regular bit life increases of as much as 300 percent in some cases, the design is quickly being recognized for its cost-saving operational impact. In Sudbury, the mine operation realized actual cash savings of more than C$45,000 within an eight-month period by making the switch to Stage3 bits. For years, the Sudbury Basin team has relied on the Alpha Extended Crown bit with the Express Waterway geometry option, ordering approximately 500 units per year. This 07 COM ECEX configuration performed well in medium-hard, non-abrasive to ultra-hard, non-abrasive formations with an average bit life of 150 m (490 ft). While satisfied with the performance of the Alpha Ex-tended Crown, the team agreed to put the new Alpha Stage3 to the test. Boart Longyear?s field engineers supplied five drill sites with Alpha Stage3 bits in a 07 COM configuration. After thoroughly testing the Stage3, the results were clear. Even with the well-known performance and versatility offered by the previously preferred configuration, the Stage3 set a new standard of bit performance. The new bit maintained its cutting edge for up to three times longer than the Alpha Extended Crown, a significant performance increase when compared to the 07 COM ECEX.

Jan 1, 2009

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

By Qinghua Gu, BUQING XUE, XUEXIAN LI, JIANGSHAN SONG, Qian Wang

To solve the problem of time-consuming and low precision in updating the open-pit vehicle transportation network, a high precision road network model construction method for unmanned vehicles in open-pit mines is proposed. This method can be divided into two steps. In the first step, an improved deep learning image processing model named DeepLabv3 + C (DeepLabv3 + Concat) is presented. Then, the road information extracted by the DeepLabv3 + C network is used to construct a three-dimensional model of the open-pit mine road network. In the second step, aiming at the time-consuming problem of unmanned vehicle meeting in open-pit mines, a vehicle meeting strategy was proposed. This strategy is used to guide the navigation of unmanned vehicles in open-pit mines. Besides, the DeepLabv3 + C network is verified by comparing the mIOU (means Intersection Over Union), accuracy, and continuity of road image extraction with the mainstream networks. The road network model constructed in the first step is quantitatively analyzed, and its performance is compared with GPS trajectory clustering methods. At the end of the paper, vehicle running simulation is carried out on the road network model by using Unity (a 3D visualization simulation software). The results show that the road network model constructed by this method can meet the navigation requirements of unmanned vehicles in open-pit mines, and the feasibility of the vehicle meeting strategy is proved.

Jan 11, 2022

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

A possible process for extracting tellurium and antimony from a residue generated in alkaline sulfide leaching of telluriumbearing alkaline skimming slag was proposed. The central composite design was employed to define the optimal leaching conditions for tellurium and antimony extractions from the residue sample. Using a 23 factorial matrix, the best performance for tellurium and antimony extractions (96.36% and 99.64%) were obtained at 175 g L−1 Na2S concentration for 80 °C during 60 min. The notable degree for influencing tellurium and antimony extractions was leaching temperature, Na2S concentration, and leaching time. The analysis of variance results indicated that the regression model was significant and suitable to be used for the optimization of independent variables within the range. The model was validated under optimal operating conditions based on the experimental design results. Antimony and tellurium in the leach liquor were separated and recovered by H2O2 oxidation followed by Na2S-Na2SO3 reduction. 98.93% of antimony was precipitated selectively during H2O2 oxidation, while 95.06% of tellurium was precipitated during Na2S-Na2SO3 reduction. NaSb(OH)6 and elemental tellurium was obtained as the product.

According to the classification of water conservation mining in shallow coal seams in China, when the ratio of the impermeable layer thickness to the mining height is less than 18, the mining belongs to the category of special water conservation, and the strip backfilling mining method is employed. This study is based on the geological conditions in northern Shaanxi. By analyzing the stability of the impermeable layer, the stability criterion of the impermeable layer was developed. The study also investigated the compositions and properties of the backfilling materials. The results show that reasonable subsidence of the impermeable layer is allowed during mining under the basic precondition (upward cracks and downward cracks are not connected).

Jan 7, 2020

By Syd S. Peng

Mountaintop removal (MTR) mining started in West Virginia nearly 30 years ago. This surface mining method can extract multiple coal seams as thin as a few inches in whole and minimum rock dilution in very steep mountainous terrain. MTR is highly efficient, even if coal seams are in close proximity and small in a real extent. Consequently, MTR has been widely used in the Central Appalachian coalfield (mainly Kentucky, Tennessee, Virginia and West Virginia) with great success. In that respect, there has been no demand for research and little scientific research has been performed to investigate its impact on the surrounding area. During the past two years, however, the debate over MTR mining has grown quickly and has become very intense. This article describes chronologically issues raised by various parties, legal actions, impacts on mining permit applications and research projects developed to address the issues.

Jan 1, 2000