Search Documents

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001

By Charles J. Kucera

Today's highly publicized issues of resource development and environmental protection are not new. But recently these issues have been played one against the other, and some would have us believe they are mutually exclusive. Why? Because modern man has realized that the shortest route to achieving economic progress is to subdue nature. He extracts mineral resources from the earth to provide the raw materials upon which other processes and services are based. But often in his search for economic progress he finds that other highly- held values (e.g., an unspoiled environment) have been violated. The natural response is a counter action - to attempt to protect nature. But this response is basically unsatisfactory because it is reactive.

Jan 1, 1979

By G. van Eck, H. Smit, L. Meyer

The Cook Islands (CI) possesses within its Exclusive Economic Zone (EEZ) a massive field of polymetallic nodules representing one of the world’s largest undeveloped cobalt deposits, along with large quantities of other metals critical to achieving global energy transition targets. In February of 2022 the Seabed Minerals Authority (SBMA) of the CI granted Moana Minerals a license to conduct our nodule exploration program. This paper describes how Moana Minerals chose to approach conducting exploration activities, one of the greatest challenges to Deep Sea Mining (DSM) development and the securing of the social license to advance to eventual mining of the resources, in an unconventional manner. The remote location of the project poses logistical challenges in mobilizing to and operating in the region and is a significant cost driver. Historically, exploration campaigns mobilized large vessels from mainland Europe, the Americas, and Asia as this model works well when contemplating long duration and widely temporally spaced campaigns without the need to revisit. Moana Minerals, when considering these challenges determined a multi-year deep sea mining (DSM) exploration program conducted in such a remote location can be better optimized by the deployment of a smaller yet highly capable “exploration optimized” vessel that is dedicated to the task and is based full time in the Cook Islands. INTRODUCTION The paper describes the challenges of exploration in remote regions including the South Pacific, and how an unconventional consideration of the problem led to the solution. Completion of an Environmental and Social Impact Assessment begins with a detailed environmental scoping study, resource update sampling requirements, and engineering data and sample requirements, which identifies the exploration goals of the project and technology needed to accomplish those goals. The method walks the reader through vessel and technology selection, discusses the challenges of equipment selection considering size and capability, describes the final arrangement, and provides results from the initial exploration campaigns. We followed the project from conception through the shipyard conversion, mobilization, and initial operations in the Cook Islands. The result shows how a smaller vessel with limited budget makes a large impact on the exploration capabilities in the region while building public trust. The Anuanua Moana is the first dedicated deep sea minerals exploration vessel modified with a suite of technologies that allow it to compete technically with existing ships but operate locally in the smaller ports of the South Pacific. The unique combination of size and technical capability gives the Anuanua Moana advantages over other vessels. This paper shows the importance of the Anuanua Moana in the development of offshore exploration strategies in the emerging deep sea minerals space.

Feb 22, 2026

By R. L. Virta

Four companies mined ball clay in four states during 2005. They included H.C. Spinks Clay (owned by Franklin Minerals), Kentucky-Tennessee Clay (owned by Imerys), Old Hickory Clay and Unimin. Production was estimated to be 1.32 Mt (1.45 million st) valued at $53.3 million, based on the results of a preliminary survey of the ball clay industry. Production in 2004 was 1.22 Mt (1.34 million st) valued at $54.1 million. Tennessee was the leading ball clay producer state with 61 percent of domestic production, followed by Texas, Mississippi and Kentucky.

Jan 1, 2006

By J. W. Jamieson, J. Escartin, A. Steinführer

Evidence of hydrothermal activity on two Mid-Atlantic Ridge oceanic core complexes (OCCs), at 13º30’N (the Semyenov 1 through 5 fields) and 13º20’N (the Irinovskoe field) (Fig. 1) were studied using CTD casts, dredges, TV-grabs and SP surveys during previous research cruises to these sites (Cherkashev et al., 2013, McLeod et al., 2009). In late 2013, the Semyenov and Irinovskoe fields were revisited, this time with an autonomous underwater vehicle (AUV) and a remotely-operated vehicle (ROV) during the ODEMAR (Oceanic Detachments at the Mid-Atlantic Ridge) cruise on the French research vessel "Pourqoui Pas ?". Here we present the first visual surveys and direct sampling of these vent sites. High-resolution (~2 m) bathymetry of the 13º30’N and 13º20’N OCCs and their associated vent fields was collected during 4 and 5 AUV dives, respectively, using the GEOMAR AUV "ABYSS" (Fig. 1). These surveys were flown between 70 m and 100 m above the seafloor, typically at a constant height to reduce vehicle movement. The AUV was equipped with Eh, turbidity, and temperature sensors in order to detect active hydrothermal venting. Over twenty ROV dives with the ROV "VICTOR 6000" allowed for the visual exploration of the OCCs and collection of 59 hydrothermal rock samples from the vent fields. As a result of these exploration activities, the first robust estimates of the size of the deposits, and the geologic controls on sulfide accumulation at these sites can be determined.

Sep 1, 2014

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

The truck haulage data from open-pit mine sites are usually massive and multidimensional with multi-peak Gaussian distributions. Artificial neural networks (ANNs) are well-known machine learning algorithms to handle massive and multidimensional data for building models. Moreover, Gaussian mixture modeling (GMM) is a suitable option for processing the data under multi-peak Gaussian distributions and improving model accuracy. For the first time, this study used a back propagation neural network (BPNN), an extreme learning machine (ELM), and a Bayesian regularized neural network (BRNN) coupled with GMM to deal with the complex truck haulage data and build three weighted ensemble models (WE-BPNN, WE-ELM, and WE-BRNN models) to predict truck productivity at mine sites. Decision tree (DT), random forest (RF), gradient boosting machine (GBM), and extreme gradient boosting (XGBoost) were used to build models to be compared with the weighted ensemble models. The results showed that the WE-BRNN had a higher accuracy than the WE-BPNN and WE-ELM models. The proposed weighted ensemble models performed better than the benchmark models in predicting truck productivity, indicating that a weighted ensemble approach based on the GMM analysis significantly improved the model accuracy. Based on the relative importance analysis, haul distance was the most crucial input variable for predicting truck productivity. This study provides a new approach to predicting truck productivity, which will help mining companies make sound budget decisions and improve mine planning.

Mar 2, 2023

By R. J. Robbins

The mechanization of hard rock underground mines offers a large potential for reducing cost, improving efficiency, and increasing profitability. However, in spite of serious efforts by quite a number of equipment developers and mining company initiatives, the industry has achieved little real progress. The task is difficult and the blasting alternative to mechanical excavation is an effective and well-developed method, which continues to improve in spite of its inherent limitations. A large number of machines have been built and tried. Only a few developments have succeeded to make a major impact on underground hard rock mining. It is certain that hard rock mines would be laid out and designed quite differently if the mining engineers knew they had available continuous mechanical excavation machines. In the absence of the machines, mines will be designed for excavation by traditional methods. It is not easy to utilize mechanical excavation in a mine which is designed to operate with normal drill and blast excavation. This is certainly an impediment to machine development. But what if an ore body cannot be mined conventionally, simply because the mining company cannot get permits to satisfy the ever increasing strict EIS requirements of the general public and governmental agencies? This may provide the incentive necessary to develop the equipment that will be needed by a new mining method that will have almost no impact on the environment.

Jan 1, 2001

By B. R. Stewart, L. W. Zelazny

The exclusion of coal fly ash from regulation as a hazardous waste has led to increased interest in returning ash to the coalfields for co-disposal. A multi-year column study used coal refuse with high potential acidity (4% total-S), and two alkaline ashes in various bulk-blends. The unamended refuse acidified rapidly, producing acidic (pH 1.7) leachates, high in dissolved metals. Treatments blended with sufficiently high amounts (20 to 33%) of alkaline ash produced alkaline (pH >8.4) leachates with low metal levels, while lower ash blending rates acidified over time to produce metalliferous leachates. Examination of solid materials indicated that pyrite oxidation was occurring to some extent in all treatments. A regression equation (r2 = 0.95) was developed to estimate time to net acid release for mixtures of these materials. Ash alkalinity and refuse potential acidity must be balanced to insure water quality for co-disposal environments, or the ash materials should be isolated away from acidic drainage waters.

Feb 24, 1997

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By Dennis Ofiara

Several recent tunnel jobs have required special adaptations of hard rock TBMs. Some of the special job conditions are ?no blast? launch requirements, small shafts or launch pits, proximity to existing underground structures, and short tunnels where the TBM must be retrieved through the primary lining. This paper describes a few of these projects, and the machine adaptations that have made TBM excavation feasible.

Jan 1, 2008

By George Anagnostou

Time-dependent ground behavior may have important implications for the construction process or the life of a tunnel. The paper gives a concise overview of the influence of time on the deformations and the stability of underground openings, including topics such as face stability in soft ground or the time-development of pressure or deformations in squeezing or swelling rock. While keeping in mind practical questions of tunnel engineering, emphasis is placed on understanding the observed time-dependency, on the underlying mechanisms (such as pore water pressure dissipation or chemical processes) as well as on the respective inherent prediction-uncertainties and design-uncertainties.

Jan 1, 2007

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

By J. A. Rusnak, M. M. Gadde, S. S. Peng

In situ stresses are one of the key inputs to a successful underground excavation design. Because of the complex mechanisms involved in arriving at the current state of stress at a point in the Earth’s crust, often the only reliable way of estimating in situ stresses is by actual measurement. In the United States coal mines, overcoring relief method is by far the most popular technique used for estimating the virgin stress field. Typically, for stress measurement with overcoring, a vertical borehole is drilled into the roof or floor of an underground coal mine opening to a certain distance and change in borehole diameter is monitored at multiple points along the length of the hole when this borehole is overcored. For the measured stresses to represent the pre-mining stress field, the measurement points should be located beyond the influence zone of the mine opening. Actual data from several US coal mines have been collected to check if the measured stresses by overcoring represent true in situ stresses. The data indicate that most of the stress measurements were within the excavation influence zone. A three-dimensional numerical modeling methodology was applied to one of the collected cases to correct the measured stresses for the excavation influence. The modeling approach demonstrated the usefulness of integrating numerical modeling into a stress measurement program to estimate ‘true’ in situ stresses.

Jan 1, 2006

By Wern-ping (Nick) Chen

The Florida Department of Transportation District 6 (FDOT D6) began a study in 1987 for a master plan to improve the traffic circulation and congestions between the Port of Miami (POM) and downtown Miami, FL. This study included a tunnel connection between two man-made islands, the Watson and the Dodge islands. Though a finding of no significant impact (FONSI) was completed in 1992, the project remained on hold for about 10 years. In 2002, Florida Turnpike took over this project, re-evaluated its benefits to the lo-cal communities, determined its feasibility (specifically the tunnel options) and established a probable cost. In 2005, the FDOT D6 regained its charge over the project and concluded that a bored tunnel under Biscayne Bay is feasible. Its primary components are: ? Widening of the MacArthur Causeway Bridge, to accommodate truck traffic to the Port of Miami. ? A tunnel connection between Watson Island and Dodge Island, where the POM is located. ? Connections to the POM roadway system, either for the traffic from the city of Miami or for the truck traffic from I-395 to the POM. The project will improve access to and from the POM and provide a dedicated roadway connector linking the POM with the MacArthur Causeway (State Route 41/1) and I-395, specifically for the trucks in and out of the POM without going through downtown Miami. As identified in the project information memorandum (PIM), its primary objectives are to: ? Improve access to the POM, helping to keep it competitive and ensuring its ability to handle projected growth in its cruise and cargo operations. [ ] ? Improve traffic safety in downtown Miami by removing POM traffic, trucks and buses from the congested downtown street network and, in doing so, facilitate ongoing and future development plans in and around downtown Miami.

Jan 1, 2009

By E. R. Bauer

In response to the mandates in the MINER Act of 2006, NIOSH conducted refuge alternatives research that included characterizing the utility, practicality and survivability of refuge chambers and outby safe havens. NIOSH also prepared and delivered a report to Congress in late December 2007 that summarized the findings of the research, included recommendations concerning the design and performance specifications for refuge alternatives, and focused on specific information that could inform the regulatory process on refuge alternatives. This document highlights NIOSH's research and recommendations concerning refuge alternatives, survivability evaluations of refuge chambers, and presents a brief review of the current deployment of refuge chambers in underground coal mines in the U.S. The research has lead to the conclusion that refuge alternatives have the potential for saving the lives of mine workers if they are part of a comprehensive escape and rescue plan, and if appropriate training is provided. DISCLAIMER: ?The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.?

Jan 1, 2009

The Barrick Zaldivar mine is an openpit, heap-leach copper mine in Region II of northern Chile at an elevation of 3,300 m (10,826 ft), approximately 1,400 km (870 miles) north of Santiago and 175 km (109 miles) southeast of the port city of Antofagasta. In 2006, Zaldívar produced 307 million lbs of copper, with reserves estimated at 5.7 billion lbs. The mine uses conventional methods of openpit mining: Pure cathode copper is produced by three stages of crushing and stacking the ore, followed by heap leaching and bacterial activity to extract copper from the ore into solution. A solvent extraction and electrowinning process then removes the copper from solution and produces the cathode copper. A flotation plant also recovers copper contained in the fine fraction of the crushed ore. In 2006, an existing A-frame structure that covered copper ore from the mine?s secondary crushing operation was damaged beyond repair. The material delivery configuration of this original structure had the conveyor carrying incoming ore directly over the low roof to drop ore into the building at its peak, and ore trickling from the sides of the conveyor had accumulated on the roof, overloading it. A better solution had to be found, and fast: First, the Chilean Commission does not permit uncovered piles of this type since the extremely fine material leads to serious pollution problems. Second, Barrick Zaldivar is very concerned about worker safety, and the amount of dust created by the uncovered pile was not acceptable. Finally, some amount of copper was lost in the dust generated by the winds of the Andes. The major issues faced by Barrick Zaldivar in designing a new structure included:

Jan 1, 2009

By Peter L. McSwiggen

The mineralogy of the Biwabik Iron Formation changes dramatically from west to east as the formation nears the basal contact of the Duluth Complex. This reflects a contact metamorphism that took place with the emplacement of the igneous Duluth Complex at tem¬peratures as high as 1200 °C. However, the mineralogy of the Biwabik Iron Formation also varies vertically through the stratigraphy of the unit. This variability in both the vertical and horizontal dimensions makes it difficult to predict exact horizons where specific minerals will occur. The iron-formation has been subdivided into four broad stratigraphic units (lower cherty, lower slaty, upper cherty, and upper slaty) and into four lateral mineralogical zones (1-4). Zone 1, the westernmost zone, is characterized by quartz, magnetite, hematite, carbonates, talc, chamosite, greenalite, minnesotaite, and stilpnomelane. The silicate mineralogy in Zone 2 of the Biwabik Iron Forma¬tion changes very little. However, the minerals begin to change dramatically in Zone 3. Most significantly, Zone 3 is characterized by the appearance of grunerite in both a tabular form and a fibrous form. In Zone 4, the original silicate minerals have completely reacted, and a new suite of minerals occupies the iron-formation. These include grunerite, hornblende, hedenbergite, ferrohypersthene (ferrosilite), and fayalite.

Jan 1, 2007