Search Documents

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert system shells designed for real-time processing plants that also included the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. Significant performance increases have been achieved using these systems, but in general, they suffer from the static nature of their rules and to a degree the process models also. Typical improvements quoted in the literature suggest throughput rate increases of 4 to 8 percent and recovery increases of 1 to 4 percentage points. In over 30 years of designing and installing expert systems we have never seen performance numbers less that these but have often seen numbers in excess of the high values. However, once the system has been installed and tuned up the performance usually does not improve much thereafter. Granted, the initial increases in throughput rate and recovery are significant but a question always lingers, that is, can the expert strategies be modified further to squeeze a little more improvement out of the system. The answer to this question is a resounding yes, however a complete understanding of what we do well as designers and operators of expert control systems is required as well as how we can improve upon our best practices is required to move us from the performance plateau we have been on for a number of years to a new higher level of performance.

Jan 1, 2009

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Clayr Alexander

Stillwater Mining Co. (SMC) is engaged in developing, extracting, processing and refining palladium, platinum and associated metals (PGM)from the J-M Reef. This geological formation is located in Stillwater, Sweet Grass and Park counties in southern Montana. Associated byproduct metals include rhodium, gold, silver, nickel and copper. SMC’s current mining operations are near Nye, MT. The company is currently developing a second underground palladium and platinum mine, the East Boulder project, about 21 km (13 miles) west of the Nye operations. A 5,650-m (18,550-ft) tunnel is required to gain access to the ore-bearing horizon (J-M Reef).

Jan 1, 1999

Editor?s note: Each year, the June issue of Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue. Thank you to the industrial minerals annual review editor, to the technical committees chair and vice-chair, and to the authors of the individual commodity profiles. Jim Norman, member SME, of GeoTrans, Inc., is the industrial minerals annual review editor. SA Ravishankar, member SME, of Cytec Industries, is chair of the industrial minerals technical committees. Technical committee vice chairs include: ? Abani Samal, member SME, of Pincock Allen & Holt, agricultural minerals. ? Aaron McMahon member SME, of Pincock, Allen & Holt, ceramics and refractories. ? Bradley S. Van Gosen, member SME, of the U.S. Geological Survey, chemical raw materials. ? Mark Zdunczyk, member SME, of Continental Placer, Inc., construction materials. ? Jerry Gauntt, member SME, of JEG Minerals Consultants, fillers and pigments. ? Michael Cheshire, member SME, of Indiana University, sorbents, filters and process aids. Their help makes possible this June industrial minerals issue. On behalf of ME readers, the editors thank them.

Jan 1, 2008

By D. R. Wilburn

This summary of international mineral exploration activities for 2012 draws upon information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry and presents analyses of exploration activities performed by the mineral industry. Three sources of information are reported and analyzed in this annual review of international exploration for 2012: 1) budgetary statistics expressed in U.S. nominal dollars provided by SNL Metals Economics Group (MEG) of Halifax, Nova Scotia; 2) regional and site-specific exploration activities that took place in 2012 as compiled by the USGS and 3) regional events including economic, social and political conditions that affected exploration activities, which were derived from published sources and unpublished discussions with USGS and industry specialists.

May 1, 2013

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the US mining workforce who are potentially exposed as various ore bodies are drilled, blasted, hauled by truck, crushed, screened, and transported to their destinations. The current Mine Safety and Health Administration (MSHA) permissible exposure limit (PEL) for RCS remains at approximately 100 μg/m3 , but it is noteworthy that the Occupational Safety and Health Administration (OSHA) has lowered its PEL to 50 μg/ m3 (with enforcement dates staggered through 2022 for various sectors), and the National Institute for Occupational Safety and Health (NIOSH) has held a 50 μg/m3 recommended standard since 1976. To examine a method for reducing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on eighty miners across seven unique mining sites. The data was then collated and partitioned using a thresholding scheme to determine exposures that were in excess of ten times the mean exposure for that worker. Focusing on these short duration, high magnitude exposures can provide insight to implement controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20% or more by reducing exposures that occur during just 10 min of work per 8-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By Mohammad Djavid

The one-pass tunneling pipe jacking method has often been the most schedule and cost efficient method for the pipe line installation. The main challenges in jacking pipes larger than 108 inches and for longer runs are: transportation and logistics, requiring high jacking forces, keeping line and grades, control of ground surface settlement, providing adequate external lubrication, and the potential of damaging the joints and pipe spigots. In recent years, 144" diameter pipes have been jacked for short runs of up to only 300 feet. In this article design and construction of installation of up to 1,000 linear feet run of 144-inch internal diameter, reinforced concrete pipes without intermediate jacking station in Chicago O?Hare International Airport are discussed. The article also presents discussions regarding the subsurface saturated silt formation, shallow cover, dewatering, jacking and receiving shafts, jacking forces, lubrication and settlement data.

Jan 1, 2008

By D. F. Machuca-Mory

A change of support model consists of a procedure to change a stationary histogram at a small data scale to represent a larger scale; typically a distribution of sample drill-hole data is changed to represent a chosen selective mining unit (SMU) scale. Most grade variables average arithmetically. Thus, the mean stays the same for different scales, and the variance changes according to well-established theory using average variogram values. The longstanding challenge has been to predict how the shape of the histogram changes. The discrete gaussian model is widely used because it appears reasonable and introduces few artifacts; there are no artificial minimum/maximum values and the target mean and variance are reproduced exactly. The resulting distribution shape, however, is strongly dependent on a multivariate gaussian distribution. The authors generalize the approach by taking advantage of a property of the isofactorial model, which allows one to specify where the random function falls on the spectrum between a low-entropy mosaic model and a maximum-entropy diffusion model. A measure of dissemination (MD) is computed using a ratio of the madogram and the variogram. The change of support algorithm is developed that uses a variable measure of dissemination (VMD) that is easily calculated and fit to data from the deposit. The resulting VMD change of support model is very flexible to represent different mineralization styles encountered in practice; global predictions of recoverable reserves are more accurate and decision-making is improved. A number of real examples are shown to demonstrate the approach.

Jan 1, 2008

By Keith Bowers, Frank Mimnagh, Eddie Woods

The CTRL London Tunnels The Channel Tunnel Rail Link (CTRL) London Tunnels comprise 36km of internal diameter bores that were driven by Earth Pressure Balance (EPB) Tunnel Boring Machines (TBMs). The tunnels were constructed between the autumn of 2002 and the spring of 2004. The permanent works also included the 1.1 km long station box at Stratford, five ventilation shafts of depths between 30 and 54 m, 29 cross passages and various large diameter sprayed concrete lined connecting tunnels. The tunnels were driven under densely populated areas of north and east London, as depicted in Figures 1 to 4. Under the parliamentary CTRL Act the project had obligations to make

Jan 1, 2005

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The use of phosphorus by mankind is long established. From use in agriculture, foods, high tech electronics, and more recently in EV battery cathode production, one cannot escape its impact on today’s society. This paper will review and describe the circular journey of phosphorus through its value chain from the mining operation of phosphate ore through beneficiation into downstream chemicals production and finally into the EV battery cathode production space. This will include a review of phosphoric acid production from phosphate concentrate using wet process route and thermal route. The wet process route discussed will be via dissolution of phosphate concentrate by sulphuric acid. The thermal route will discuss thermal decomposition of phosphate concentrate using submerged arc furnace to produce yellow phosphorus followed by its combustion to produce phosphorus pentoxide and subsequent hydration to produce phosphoric acid. It will also discuss briefly other phosphate derivatives for specialty chemicals and recovery of phosphorus units from wastewater treatment plants, sewage sludge and incinerator ash. Finally, the paper will discuss the use of phosphorus in EV batteries in the form LFP cathode materials and its production. It will also briefly discuss the LFP battery recycle.

Sep 11, 2023

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Bauxite residue (red mud) is an alkaline waste derived from the industrial process for extraction of alumina from bauxite ore. Some bauxite residues contain considerable concentrations of critical metals, for example, rare earth elements. Lithium in red mud was also reported as a potential resource. In the current study, a Li-rich red mud was leached using acetic acid to investigate the leaching behavior of lithium followed by neutralizing with hydrochloric or oxalic acid. By neutralizing red mud using diluted hydrochloric acid (0.01 mol/L), 58.04–60.27% of lithium was leached using 25% acetic acid at 95 °C for 60 min. In the meantime, more than 95% of sodium and 85% of calcium were also dissolved in the leachate solution. While oxalic acid (0.5 mol/L) was used to neutralize red mud prior to acetic acid leaching, lithium performed lower leaching efficiencies (42.41–46.88%) in comparison of using of hydrochloric acid–neutralized red mud. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the condition. In this study, 25% (v/v) of acetic acid, at 85 °C for 60 min, was demonstrated as optimum conditions for lithium extraction from oxalic acid–neutralized red mud using acetic acid. The results would be useful and of interest for lithium recovery and purification from red mud.

By M. T. Ansari

"This article explains the ways in which investment on mining infrastructure is a geopolitical issue. It discusses the effect of installing sufficient infra structure to get the product to the world market, and argues that there is a risk involved in depending on traditional suppliers who wish to invest in the infrastructure. It explains how to make a distinction between dedicated purpose infrastructure and general use infrastructure by examining the positions of the main actors in mining projects. It argues that these positions can not be understood as analogous to projects in developed countries. To conclude, infrastructure is a crucial link in the supply chain to market but the relative size of such projects in relation to the economy means that investors decisions in developing countries have quite different implications from those in developed countries."

Jan 1, 2011

By Paul M. Godlewski, Joseph P. Gildner, David S. McAllister

With construction underway on the 22.5 km (14 mile) Initial Segment of the Link Light Rail transit system in Seattle (including the one-mile EPB-driven running tunnels and mined station at Beacon Hill), the Sound Transit Board on May 20, 2004 voted on selection of a preferred route for an approximately eight-mile extension northwards from the central business district to Northgate, and authorized immediate start of advanced conceptual/preliminary engineering and geotechnical exploration programs scheduled to be completed in Spring 2005. The extension includes approximately914 m (30,000) route-feet of bored running tunnels, a mined station with platform level approximately 60 m (200 ft) below grade, three (possibly four) cut-and-cover stations and a cut-and-cover cross-over structure, as well as an aerial terminal station at Northgate and other line-section below-grade and aerial structures. All tunneling will be in glacial soils.

Jan 1, 2005

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By T. W. Beck

Overexposure to respirable dust remains a widespread health hazard to roof bolter occupations in underground coal mines. Recently implemented mist drilling technology was evaluated for its effectiveness in controlling respirable dust exposures for roof bolting personnel. This work presents the findings from NIOSH field and laboratory studies comparing respirable dust levels on mist drilling roof bolter machines to dust levels measured on machines using a conventional vacuum drilling system. Gravimetric and instantaneous respirable dust samples were collected for multiple drilling cycles. These dust measurements were used to assess the potential dust control capabilities relative to conventional drilling. Controlled laboratory tests found 0.3 mg/m3 more respirable dust with mist drilling than with the conventional vacuum method. A separate field investigation of the two techniques observed higher dust levels around the mist bolting machine.

Jan 1, 2008