Search Documents

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By N. S. Tanious

The need to provide better mine roof support and control in longwall tailgate entries prompted the Bureau of mines to search for a replacement product for wood cribs. Their search isolated steel-fiber-reinforced concrete (SFC) as the most effective replacement. Through successful laboratory and underground mine tests, handmade SFC cribs proved to be a viable and more effective roof support system. However, to ensure wider usage, U. S. Steel Mining Co. initiated a joint development and evaluation program with Burrell Construction Company in order to mass produce SFC blocks of reasonable dimension, weight, and cost. Small specimens and full-size cribs were evaluated during this program to determine their compressive strength and post failure characteristics. After considerable testing and adjusting of various concrete mixtures, a final formulation for the SFC crib blocks was selected. That formulation permitted the construction of SFC cribs possessing a nominal crib strength of 3200 psi (22.1 x 106 Pa) and a nominal modulus of elasticity of 1.0 x 106 psi (6894.76 x 106 Pa). These SFC cribs can support from 3.5 to 14.5 times as much load as a wood crib, depending on the size of the wood crib being replaced. Both laboratory and limited mine tests, conducted by U. S. Steel Mining Co. have shown the SFC crib to be an economical and effective means of roof control.

Jan 1, 1984

By F. E. du Plessis, P. De Waal

Through the development of innovative in-line mineral quantification sensors, the possibility has arisen to apply modern control theory to implement automatic process control for electrostatic high tension (“HT”) roll separators. A pilot-scale set-up was constructed to enable continuous tests to be carried out. A typical dry mill feed was continuously pre-heated and separated with a modern lab scale HT roll machine. The mineralogy as well as mass-flow of the non-conductor stream was quantified in-line, and the combined streams were re-circulated in an endless loop by a combination of vibration feeders and a bucket elevator. A fractional factorial experiment was executed to determine the most significant control parameters of the HT roll separator. Then a multi-input, multi-output dynamic model of the HT electrostatic separator was extracted by the application of standard system identification techniques for automatic control. The most important control variable to ensure a stable product grade could be identified. This allowed a robust single-input, single-output controller to be implemented. The process variable and set-point was mineral grade and the control variable was electrode voltage. Roll speed was manually adjusted while the mineral grade was kept on set-point by the control system. The roll speed, where maximum mass flow and therefore maximum yield was produced on-grade, could therefore be rapidly determined. Atmosphere humidity and ore temperature served as disturbances. Some other adjustable parameters were kept constant during the experiments, namely feed mineralogy, splitter settings and feed rate. Delivery of maximum yield, with a controlled grade, can improve production while reducing the burden of complex manual tuning. Manual tuning previously involved coping with multiple parameters with uncertain cross coupling influences on the end result. Even the end result was typically only known after completion of mineral assays. Automatic grade stabilisation and yield optimisation for a HT roll separator bank requires in-line measurement of mineralogy and mass flow, as well as the implementation of a robust process control system.

Jan 1, 2005

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

By Louis W. Cope

Mongolia is known in western countries as the location of rich dinosaur fossil fields. However, the country is even richer in mineral resources. The Ministry of Industry and Trade reports 6,000 mineral occurrences of 80 metals and minerals. Mongolia has already attracted much foreign investment in the mining sector. Mining is the country’s largest industry. It is responsible for 17 percent of the gross domestic product, 65 percent of industrial output and 57 percent of export earnings.

Jan 1, 2006

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By Ö. Kaya

The removal of gangue minerals from three different graphite ores (Inebolu, Akdag?madeni and Çoraklidere) from Turkey by acid leaching was studied. Acid leaching experiments were applied to the flotation bulk concentrates, which were obtained in determined optimum conditions after preliminary flotation tests. The effects of acid type, acid concentration, leaching temperature and leaching time on the dissolution of gangue minerals were studied. The most suitable leaching conditions were determined to be 20% HCl + 4% HF for acid type and concentration, 85 ºC for leaching temperature and 4 hours for leaching time. After removing the gangue minerals at these optimum conditions, the total carbon contents of the samples from Inebolu, Akdag?madeni and Çoraklidere increased from 23.51% to 40.07%, from 37.93 to 60.47% and from 42.28 to 59.47%, respectively.

Jan 1, 2009

By Steve Polegato, J. Coady Marsh, Gary Landry

The Donkin-Morien Mine in Cape Breton, Nova Scotia, has successfully completed the excavation of a 7.6m (25-ft) diameter access decline over a distance of 3.5km out under the Atlantic Ocean. The tunnel, completed in December 1984, was driven through a sedimentary sequence of sandstone, siltstone, mudstone and various gassy coal seams prior to intersecting the Harbour Coal Seam where development work will commence. The tunnel was driven by a Canadian prototype tunnel boring machine (TBM) manufactured by Lovat Tunnel Equipment, Inc., Toronto, Ontario. The 7.6m (25-ft) diameter full-face shielded TBM operated at various grades from 0-20%. This paper outlines the TBM design, excavation, support and backup system utilized in the drivage. Problems encountered and drivage rates will be addressed.

Jan 1, 1985

By S. E. Phillipson

The Mine Safety and Health Administration?s (MSHA) Roof Control Division (RCD) collects a variety of geological and engineering information pertaining to mining conditions in surface and underground mines throughout the United States. Recently, lineament analyses, trends of geologic structures, and inferred stress directions based on mapping at mines with problematic ground conditions, have been integrated into a GIS. The incorporation of different kinds of information into the same geographic coordinates and map projection, placed on digital geologic maps, allows site specific data to be evaluated in a regional geospatial context, identifying trends in the orientation of horizontal stress or patterns of structural geologic features. As more information is collected, the GIS will evolve as a tool for district- and basin-wide evaluations of controls on ground instability, and may evolve into a predictive tool for some kinds of geologic hazards. In addition to the geologic and geotechnical evaluations, the GIS also serves as a searchable database of previous mine investigations. The database can be searched for a variety of criteria, and the results displayed in real geographic coordinates to find the locations of previously visited mines or to evaluate mine fatality and injury data. This not only allows old reports to be found, but also places the information in a geospatial context with respect to neighboring mines or geographic areas. The GIS also has the capability to serve as a digital mine map repository, where maps can be stored in digital, georeferenced format for display in relation to each other and various themes of interest. This allows evaluation of multiple seam mining interactions and proximity to other mines, and on a national level could serve as an abandoned mine map database.

Jan 1, 2008

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill. The design of the Hicom mill is unique. Based on a high speed centrifugal motion of the grinding chamber, very high power intensity is delivered to the grinding process. Most significantly, a high acceleration field, 50 times stronger than gravity is produced, creating very high power input per unit of mill volume, and exceptionally fast particle breakage rates, typically 50 - 100 times greater than those in conventional tumbling mills. A mill developing such forces has significant implications to comminution technology and practice.

Jan 1, 1999

By G. M. Wali Ullah, MEHMET KIZIL, ` Micah Nehring, PETER KNIGHTS

In operations that use the sublevel stoping mining method, production scheduling takes into account factors, including ore reserve envelopes, ore grade averages, equipment capacity, feed controls to the mill, and geotechnical restrictions, across the scheduling horizon. Mathematical programming is one of the most effective methods for enhancing the decision-making process in regard to the most viable production schedule in light of a given set of limitations. The majority of research on sublevel stope mining focuses primarily on a single objective of optimisation, which is to maximise the net present value (NPV). Environmental, social, and governance (ESG) considerations are becoming more prevalent in the mining industry. This includes aspects relating to deforestation, land disturbances, gas emissions, community relations, and water usage, among many others. Institutional and other kinds of investors are becoming more interested in the work that resource companies do regarding their ESG obligations. This review article identifies the gap in the existing literature and proposes to simultaneously optimise the production schedule around three objectives. Two of these relate directly to ESG aspects.

Nov 6, 2023

By A. D. Kalogeropoulos, T. N. Michalakopoulos

This paper deals with the numerical simulation of rock cutting laboratory tests using the discrete element method. The main objective is to provide a method for calibrating numerical DEM models of rock cutting in a systematic way so that realistic results are yielded. The numerical models are developed with the discrete element code Yade, which models rocks as a collection of bonded spheres. The models are calibrated in a four-step process based on the design of experiments method and optimization. The calibrated models are evaluated both quantitatively and qualitatively against actual laboratory cutting tests, in terms of the ratio of the simulated mean cutting force to the actual one and the cutting force time series, respectively. The fully calibrated models showed that the simulated cutting process matched qualitatively the actual cutting force recordings and underestimated the mean cutting force by approximately 3%. It is concluded that well-calibrated numerical simulations of the rock cutting process can provide not only a better understanding of the process itself but also quantitative data regarding the cutting force and energy requirements.

Dec 28, 2022

By R. M. Tyson

Sulfides present in the troctolitic and footwall rocks are placed into one of three major zones (hornfels, cloud, and basal) on the basis of their stratigraphic position and mineralogy. Hornfels sulfides, enriched in Fe, represent remobilized sedimentary sulfide. Sulfides from the Cloud Zone are probably magmatic and are enriched in PGE, Cu, Ni, and Ag. The basal sulfides, composing most of the ore, resulted from contamination of the magma by remobilized sedimentary sulfide. The basal sulfides exhibit a differentiation trend in their mineralogy and chemistry. PGE, Cu, and Ag are enriched with increasing differentiation which is attributed to fractionation within an immiscible sulfide liquid.

Jan 1, 1986

By M. K. Mohanty

Over the years, screen bowl centrifuges have been widely used for dewatering fine coal in coal preparation plants in the United States and elsewhere. Its popularity is attributed to its relatively low cost, its high capacity of providing low moisture content product and its relative ease of operation and maintenance. It is generally recognized in the engineering and scientific communities that screen bowl centrifuges provide some degree of particle size separation while dewatering fine coal in a common application. However, the extent of differential partitioning of coarse and fine particles achievable by a screen bowl centrifuge has not been systematically studied in the past. The present investigation was aimed at conducting a parametric study using a statistically designed experimental program to better understand and optimize the size classification performance of a screen bowl centrifuge. A continuously operating screen bowl centrifuge having a bowl diameter of 0.5 m was used for this study at the Illinois Coal Development Park. Three key operating parameters, i.e., feed flow rate, feed solid content and pool depth, were varied to conduct a total of 17 experiments using a three-level factorial test matrix. Some of the best size separation performances achieved in this study may be described as having an imperfection value of 0.13 at an effective separation size (d50c) of 38 µm and an imperfection value of 0.27 at an effective separation size (d50c) of 2.8 µm. Due to an effective separation of ultrafine high ash materials, the ash content of the screen bowl feed was reduced from 22.3% to a minimum of 8.84% with a combustible recovery of 84.1% and an ash rejection of 71.6%. A higher combustible recovery of 92.1% was achieved at a product ash content of 12.5% with a d50c of 2.8 µm and imperfection of 0.27.

Jan 1, 2008

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985