Search Documents

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By A. G. Moon

Kennecott Copper Corporation's Chino Mines Division concentrator is located in Hurley, New Mexico. Construction of the concentrator was started in 1910 and its capacity was progressively increased over the years to the present nominal 20, 425 t/d of ore (22, 500 stpd). The principal copper minerals present in the ore are chalcopyrite and chalcocite with much of the chalcotite intimately associated with pyrite. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the deisred pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. In 1972 a major renovation of the flotation and regrinding circuits was com¬pleted and at that time a new lime distribution and control system was placed in operation. Limestone is obtained from a nearby quarry west of Hurley. The limestone is crushed, sized and fed to a rotary kiln and the quicklime product is stored prior to slaking. The lime is slaked, as required, in a mixing tank-classifier type slaker and the lime slurry is pumped to a concentrator storage tank from which it is distributed through a conventional closed loop system. The current average lime usage rate is approximately 6 kg/t of ore (12 lb per st).

Jan 1, 1976

By G. Hoffman

Sustainable development has brought social, environmental and energy efficiency concerns together with management and governance of natural resources. Cement manufacturing, an energy- and natural resource-intensive industry, is adapting to meet sustainable development goals. Emission standards for cement plants and increasing energy costs have lead to changes in the use of natural resources and recycled materials. Utilizing pozzolans or supplementary cementitious materials (SCMs) as mineral admixtures in blended cement or as a substitute for cement in concrete lowers energy costs and CO2 emissions. Although the western U.S. is rich in natural pozzolans, artificial products, particularly fly ash, have greater use as mineral admixtures. Pozzolans and SCMs have many beneficial properties, such as preventing alkali-silica reactivity, a common problem in the western U.S. Barriers exist for mineral admixtures in the cement and concrete industries because of past inconsistencies in quality or availability. New environmental regulations on the primary industries producing artificial mineral admixtures could adversely affect the quality and quantity of these materials in the future.

Jan 1, 2009

By A. A. Bilgin

The prevention of acid mine drainage (AMD) in situ is more attractive than down-gradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied to an abandoned coal mine pool in Pennsylvania. The pool had a pH of 3.0 to 3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by the enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2007

By D. Drymonitis, G. Gialoglou

"Placer gold mineralizations have been observed in the north-eastern parts of Greece. Some of them have been at first evaluated to be of special interest so, exploration campaigns have been designed and carried out. Among the other exploration techniques applied on the sites of interest, drilling was the one to give the detailed information and data for the evaluation of the deposits. Having collected the data from trenching and two consecutive drilling campaigns, they were processed geostatistically to estimate the ore reserves and therefore the economic interest of the deposits. The latter was done by using exploitability indices, which would give a rough idea whether the deposits were economically feasible. A small number of such deposits have been spotted in the area and have been explored and evaluated as above. The present paper deals with the most important of them, giving all the process followed and the results derived from the exploration carried out."

Jan 1, 2005

By Paul D. Tomlingson

The difficult and often harsh working environment of the mining industry can stress both personnel and equipment to the extreme. Often, the unintended consequences of this environment lead to confrontations between departments, as each goes about its tasks of mining, maintaining or supporting these activities. On occasion, the confrontations may result in criticism of other departments for perceived or real sins or omissions. The offended department may not be able to change the circumstances, but can only complain while frustration persists. The most effective solutions are the actions of the mine manager. By establishing mutually supporting roles of each department and specifying conditions for the interactive conduct of maintenance, the mine manager can better assure that the inherent problems of the mining environment are neutralized.

Jan 1, 2011

By Z. Mullard

The introduction of social media platforms has ushered in a new era of interaction and information exchange, which impact business-to-society relationships. Mining companies are closely watching these platforms, as the industry takes a cautious approach to control flows of information. This paper explores the risks, challenges and opportunities of using social media, based on a qualitative mixed methods investigation with stakeholders from the Canadian mining industry. Generational and language barriers, misunderstanding and limited motivation from regulators make implementing social media platforms challenging and risky at an organizational level. The benefits of social media include being able to mobilize communities and share information in real time. Despite the challenges, the study found that 62% of mining stakeholders are incorporating social media tools, mostly in an ad hoc manner. Flexible strategies for transparent communication and public engagement are creating new opportunities for information exchange.

Jan 1, 2011

By T. B. Acton

There are two types of ore transportation systems in use at Newmont's Magma Copper Co. San Manuel mine in Arizona-rail-mounted, box-type rotary cars and the newer rail-mounted, bottom-dumping ASEA cars. Though the cost per car for the ASEA units greatly exceeds the cost per rotary car, the advantages of the ASEA units, including much faster dump times, have made the ASEA system a successful alternative at the San Manuel mine. The rotary system of ore transportation has been in use at San Manuel since production began in 1956. The system employs 7.9-m3 box-type cars to transport ore by rail to shaft pocket areas. A rotating dumping mechanism turns three cars at a time upside down to empty them, and returns them to an upright position. Trains of 15 cars each are dumped in about six minutes. Each 15-car train is pulled by an 18-t rated trolley locomotive. There are about 400 rotary cars in service at San Manuel and the system is used for the majority of ore haulage. This well-proven rotary method was instrumental in achieving the December 1977 world record of 272 Mt hoisted from an underground copper mine. Magma Copper Co. began using ASEA cars in late 1977. Designed by ASEA of Sweden, the cars are built for San Manuel by Kasper-Hall Manufacturing Co. in Tucson. The cars basic design feature is a hinged floor that opens at the side as the car is pulled through the dump. As it passes over the dump, a fifth wheel attached to the hinged floor (opposite the hinges) travels along a rail in the dump. This rail dips down into the pocket and then returns to track level. As the fifth wheel travels along the rail, the car floor opens, the car dumps, and the floor is then returned to track level. As the car is dumping, the body remains suspended over the pocket by wheel rollers attached to each side of the dump. Trains of 10 cars each are emptied in about 45-50 seconds. Each ASEA train is pulled by an 18-t rated trolley locomotive, adapted at San Manuel to allow it to pass through the ASEA dump. At minimal cost, "wings" are welded to each side of the locomotive. These wings suspend the locomotive over the pocket as the train passes through the dump. Advantages of the ASEA System Major design characteristics of the ASEA and rotary systems are shown in the accompanying table. The comparison points out some of the following advantages demonstrated by the ASEA system. • Faster dumping-An ASEA train dumps in 50 seconds, while a rotary train takes at least six minutes. There is no stopping or starting when dumping an ASEA train. The train enters the dump area, dumps, and leaves in one continuous motion-in contrast to rotary trains which must stop and start five times to dump. With the rotary system, three cars are spotted in the dump mechanism by remote control. When the cars are in place, the train operator activates the dump, the cars are turned over, and then returned to an upright position. This process is repeated until all 15 cars in the train are emptied.

Jan 4, 1980

By Todd Schrauf, James Scott, Mark Smith

"Cyanide heap leaching of gold ores in areas with extremely low winter temperatures requires special considerations to prevent freezing of the leach solution. Factors that impact the solution temperature include ore temperature at the time of stacking and during operation, burial of drip irrigation lines, use of geomembrane covers and heating of the leach solution. Thermodynamic modeling was performed to simulate expected ore and solution temperatures under different operating strategies for Kaminak Gold’s Coffee gold project in the Yukon Territory. Mean monthly temperatures at the site ranged from a low of -22.5 °C (-8.5 °F) to a high of 13.6 °C (56.4 °F), while in situ ore temperatures ranged from -0.5° to about -1.5 °C (31 ° to 29 °F). The modeling results were used to optimize the operational parameters and indicated that a combination of drip line burial and heating of the leach solution during the winter months was required to maintain solution temperatures above freezing during the initial years of stacking, although as the size of the heap increased, heating was no longer necessary.Modeling objectivesThe successful operation of a cyanide heap leach under extremely cold winter temperatures requires the implementation of operational strategies to prevent freezing of the leach solution and the ore within the heap. Thermodynamic modeling of the heap provides the means to quantify the effectiveness of these different operational parameters on maintaining the required operating temperatures to avoid freezing within the heap. The operational parameters that were evaluated with the model included:"

Apr 1, 2016

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By James R. Walpole

Less than 100 years ago the first major federal regulatory agency, the Interstate Commerce Commission was established (in 1887), and since that time literally hundreds of other federal agencies have been created. The regulations set by these agencies tremendously affect the individual citizens of this country as well as U.S. institutions. A few examples of the myriad agencies established include the Food and Drug Administration. (1907), the Bureau of Mines (1910), the Federal Reserve System (1913), the Federal Trade Commission (1914), the Tennessee Valley Authority (1933), the Securities and Exchange Commission (1934), the National Labor Relations Board (1935), the Small Business Administration (1953), the Federal Maritime Commission (1961), the Equal Employment Opportunity Commission (1965), the Farm Credit Administration (1971), etc., etc. Eight years ago, on December 2, 1970, still another federal agency was established by the reorganization plan of President Nixon -- the Environmental Protection Agency (EPA). The Administrator of EPA was given authority to regulate certain activities affecting the environ-ment, which were formerly within the jurisdiction of the Department of Interior, the Department of Health, Education and Welfare, the Federal Radiation Council, the Atomic Energy Commission, the Department of Agriculture, etc. Within weeks after the formation of this Agency, Congress began to enact legislation which would be administered by EPA. Over the last eight years a considerable number of such laws have been passed, a few of which include: the Clean Air Act (1970), the Noise Control Act (1972), the Federal Water Pollution Control Act (1972), the Marine Protection, Research, and Sanctuaries Act (1972), the Federal Insecticide, Fungicide and Rodenticide Act (1973), the Safe Drinking Water Act (1974), the Toxic Substances Control Act (1976), the Resource Conservation and Recovery Act (1976), the Clean Air Act Amendments of 1977, etc. It may be helpful to review, in a summary fashion, the major provisions in some of these statutes, and accompanying regulations, as they relate to water quality control in the mining industry. The Safe Drinking Water Act and the Federal Water Pollution Control Act contain provisions to be examined, as well as the Resource Conservation and Recovery Act and the Toxic Substances Control Act. One other law, the Surface Mining Control and Reclamation Act (1977), is not administered by EPA although it does contain many provisions related to environmental control, and it will also be dis-cussed because of its importance to the mining community.

Jan 1, 1978

By Shi Wang, Hongbin Liu, Meiliang Wei, Wu Liu, Xiaojun Wang, Yuxian Ke, Xuepeng Song, Tiejun Tao

The study investigates the influence of water migration on the fluidity of fresh cemented paste backfill (CPB) with and without flocculant under variable shear rates. The research utilizes nuclear magnetic resonance (NMR), rheological tests, and scanning electron microscopy (SEM) to analyze water migration, rheological properties, and microstructure evolution. The findings reveal that water migrates to more stable states as shear rate increases, and the addition of flocculant enhances water migration and increases shear stress and apparent viscosity. The study establishes relationships between water content and rheological parameters, providing insights into the flow characteristics of fresh CPB for pipeline transportation.

May 4, 2022

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By F. M. McEvoy, E. J. Steadman, R. Murfin

In England, the provision of aggregate is determined by the historical relationship between construction and aggregate consumption. This approach does not necessarily lead to sustainable decision-making and can be seen as being driven by political expediency, rather than reasonable environmental consideration. The introduction of the statutory requirement for Strategic Environmental Assessment (SEA) in the UK has provided the opportunity to examine this issue on a more rational basis. This paper provides a practical application of a SEA based approach, to the provision of aggregates at a regional level. The process, underpinned by relevant information on resources and environmental assets, suggests that alternative supply scenarios for aggregate provision are tested in a transparent, consistent manner with increased genuine stakeholder consultation. It supports a move away from "predict and provide" approaches to one where aggregates are sourced with the best balance of environmental costs and benefits.

Jan 1, 2005

By Werner Burger

The Hallandsås project with a long history, first started in 1991, is well known in the tunneling community. In the past it has been stopped twice for technical and environmental reasons. The third attempt started in 2004 using a dual mode rock TBM. The heterogeneous highly fractured and abrasive rock mass as well as large areas of water bearing zones present most difficult subsurface conditions. The tunneling concept is based on the use of watertight segmental lining and a TBM able to operate in open mode, possibilities for extensive pre excavation grouting and high pressure closed mode operation up to 13 bar to cover exceptional conditions.

By L. Gutierrez, S. Gering, C. Calderon-Arteaga

"Drill and blast represent the most important, and sometimes the costliest processes in the mine. The cost of drilling and blasting operations greatly contributes to the “high cost trends of the overall mining operations” (Afum and Temeng, 2015). The use of available information to improve the drill and blast processes can be the difference between a wasteful process and one that is optimized for costs, safety and desired fragmentation. Mining operations have access to several types of data sets that include a variety of different systems. This information can be used to improve, evaluate and apply processes for drilling and blasting. This may include different types of data from the different stages of the process (before, during and after the drilling and blasting operations), such as hole locations (planned and actual), penetration rates, drill operators, fragmentation (expected and resulting), explosive (design and usage), geology, vibration and others. This information can be used on its own or combined for further analysis to reduce costs, improve safety and evaluate results. Fortunately, due to advances in mining software, drill and blast engineers can exploit this data and create reports to evaluate results and improve the drill and blast process. However, as users start combining information from multiple datasets and establishing standard operating procedures for reporting across multiple sites, it becomes valuable to create auditable, automated and sustainable workflows for handling the information.In some cases, the task of aggregating and standardizing the data formats has already been completed and is available to consumers via the Enterprise Data Warehouse (EDW). A data warehouse team extracts data from the source systems and transforms it so that it is meaningful for decision support (Wixom, Watson, 2007). The author’s initial implementation plan for the drill and blast solution included using data stored at the sites on local servers. However, we learned early in the process that much of the work for aggregating and supplying the required data was already completed and was available in the EDW ready for use. This saved time, reduced risk and added value to the system.The goal for this case study is two-fold: to show how information can be used to make decisions and improve processes, especially highlighting the value of using an EDW for managing drill blast information; and to discuss how technical challenges encountered during the implementations were resolved. This article targets users that want to better manage their drill and blast data or try to set up standardized workflows for using this information.This case study will discuss the process of implementing a drill-and-blast workflow at multiple sites within Freeport-McMoRan (FMI) using both data at the sites and information available from the EDW."

Jan 5, 2017

By P. A. Plunkert, D. E. Morse, L. McCartan, J. F. Papp

The mineral sector is a fundamental part of the U.S. economy. It contributes to the real gross domestic product (GDP) at several levels — basic (mining), intermediate processing, manufacturing of finished goods and construction. The real GDP during 2004 increased by 4.4 percent. The nominal GDP was about $11.7 trillion. Housing starts were up by slightly more than 4 percent for the year. And the nation’s unemployment rate decreased to5.5 percent in 2004 from 6 percent in 2003. Interest rates continued to be low (prime rate was 5.25 percent at the end of 2004) but have risen gradually, following rising inflation.

Jan 1, 2005

By Floyd C. Bossard

In underground mining operations, the over- riding issue has to be protection of worker health and safety. The employees underground, making a living in a dangerous occupation, know these are major issues. These men bargain their lives and health on the presumption that the operating management knows its business, and they, the underground employees, can pursue their occupation with the assurance that management has provided a safe and healthy ambient underground environment. When management assumes the mantle of protection of underground workers, it has to be positive that qualified engineers have designed the project, and that capable operating personnel are in charge and always available. Those persons with these responsibilities must be knowledgeable in the engineering and occupational health aspects of sine ventilation. The ultimate function of a mine ventilation system is to provide a comfortable, healthy and safe ambient environment for the underground workers. The attainment of these objectives has been complicated with the increased application of electrical equipment and diesel-powered mechanized mining equipment underground (discharging toxic diesel emissions); increased production rates with the attendant increased production of airborne dust; and mine development in increasingly hostile mineral formations containing combustible strata gases, radon gas emissions, along with high heat and humidity. In general, the modern mechanization of present mining operations has resulted in a sore complex set of problems for the engineer planning the underground ambient environment.

Jan 1, 1983

By F. Freme

Coal production in the United States in 2007 totaled 1.03 Gt (1,145.6 million st), according to preliminary data from the Energy Information Administration (EIA) (Ta-ble 1). This is a decrease of 1.5 percent, or 15.6 Mt (17.2 million st) from the 2006 record level of 1.05 Gt (1,162.7 million st). Although coal production declined in 2007, U.S. total coal consumption increased for the year. Coal consumption in 2007 in the electric power sector was higher by 1.9 percent, while coking coal consumption decreased by 1.1 percent and the other industrial sector declined by 5 percent. (Note: all percentage change calculations are done at the short-tons level.) U.S. coal exports were significantly higher in 2007, while coal imports remained at about the same level. Total coal stocks increased slightly during the year, as some consumers continued to rebuild their stockpiles that had been seriously depleted in 2005 due to transportation issues. The growth in coal consumption during the year was primarily a result of the weather-related increases in the demand for electricity in 2007. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers) in the United States grew in 2007. Coal-based generation also increased, resulting in a 17.9-Mt (19.8-million-st) increase in coal consumed in the electric power sector. Coal use in the nonelectricity sector decreased by 3.8 percent to 74.7 Mt (82.4 million st). In the international markets in 2007, U.S. coal exports increased to levels not seen in recent years while coal imports were mostly static. U.S. coal exports totaled 53.7 Mt (59.2 million st), an increase of 8.6 Mt (9.5 million st) above 2006. Coal imports in 2007 ended the year at 32.9 Mt (36.3 million st), 91 kt (100,000 st) higher than in 2006. Coal prices in 2007 were split, with most domestic prices higher for the year while the international prices were overall lower. Although the average delivered price of coal increased for most users in the United States in 2007, the increases were smaller than what had been expe-

Jan 1, 2008