Search Documents

By Tuanhui Wang, Qiwei Wang, Quanrui Liu, Jianhui Xu, Chao Wang, Yu Liu, Yuefeng Li

Rockburst is a highly destructive geological hazard that can cause casualties and equipment damage. To achieve highaccuracy discrimination of rockburst intensity, this article proposes an improved model that addresses the inefficient maximum membership principle used in traditional rockburst fuzzy evaluation models. The stress coefficient σθ/σc, brittleness coefficient σc/σt, and elastic deformation energy index Wet are selected as evaluation indicators for rockburst classification. Subjective and objective weights are obtained using the Delphi method and entropy weight method (EWM). Three types of membership function distribution forms are then used to obtain the membership degrees of each indicator to rockburst grades: trapezoidal membership function (TMF), normal membership function (NMF), and quadratic parabolic membership function (QPMF). Finally, six traditional models and six improved models are established using the maximum membership principle (MMP) and weighted average-maximum membership principle combination evaluation principle (WMP), respectively. Based on the analysis of 100 sets of rockburst field data, the accuracy, precision, recall, and F1-score of the improved evaluation model are increased by 11.3%, 0.097, 0.068, and 0.089, respectively, compared to the traditional model. The Delphi-NMF-WMP model is selected as the best model, with four performance indices reaching 97.0%, 0.979, 0.979, and 0.978. The best model is applied to evaluate the rockburst intensity of the Cangling Tunnel, Dongguashan Copper Mine, and Jiangbian Hydropower Station Diversion Tunnel, with evaluation results consistent with the actual situation, demonstrating the reliability and scientificity of the model.

Feb 28, 2024

By Terry R. Guilinger

A minitest of the new potassium chloride-potassium carbonate two-stage in situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing carion-exchange reactions. The test a1 so indicates permeability anisotropy and the existence of disturbed flow fields. The research was partially funded by the U.S. Bureau of Mines.

Jan 1, 1984

By George Wilson

When pumping abrasive slurry mixtures, special attention must be given to pump design and construction. The second article in this two-part series describes some design features to consider when selecting centrifugal slurry pumps. Hydraulic Design Most centrifugal pumps are conventionally designed to achieve the desired hydraulic performance at the highest efficiency and lowest cost when handling clear fluids in reasonably clean environments. Manufacturing limitations are not imposed on the configuration of the pump, since conventional materials such as cast iron, bronze, and stainless steel are used. Manufacturers and buyers usually select the highest specific speed commensurate with the lowest cost attainable. Part life is almost infinite. When a centrifugal pump is designed for slurry service, the important factors in pump design are wear and materials of construction; size and efficiency assume lesser importance. The pump must operate at low rotational speed and the impeller has to be a truly radial flow design. These factors immediately determine that the pump must be of a low specific speed design in the range of 600 to 1800. The specific speed is a type number that is constant for all geometrically similar pumps; it designates the geometry of the impeller and casing. [ ] where n = rpm, Q = flow (US gpm), H = total head (ft), and Ns = specific speed. Since wear is a function of velocity it can be shown that for a given head and capacity, wear will increase with increased Ns. Centrifugal Pump Casing The casing has a profound effect on performance. If designed incorrectly it can destroy a large part of the energy given to the flow by the impeller, resulting in low efficiency, high hydraulic forces, and excessive wear on both the casing and impeller. In a conventional spiral volute, the static pressure around the impeller is uniform only when there is a free vortex velocity distribution in the volute, i.e., when the spiral flow from the impeller coincides with that of the volute spiral. This occurs only at the best efficiency point (BEP), between the pump's best operating zone and over capacity zone. Departure from the free vortex velocity distribution in the volute at partial or over capacities produces circumferential pressure gradients at the impeller periphery, which is directly proportional to the specific gravity of the mixture being pumped. At partial or over capacities, the flow will not tolerate the abrupt deflection at the tongue and severe energy losses and wear are created near the casing throat and on the impeller. Concentric and semi-concentric volute designs produce uniform static pressures at the impeller periphery and make the pump, much less sensitive to "off"' BEP operation. Hydraulic forces and wear are considerably reduced-eliminating the tongue prevents abrupt deflection of the flow, turbulence is minimized, and the velocity in the casing volute and throat is reduced. Good efficiency is sustained over a wider operating hand. Casings of this design are easy to cast. • Spiral volute (conventional)-Radius to the outer periphery of the casing and the volute area constantly increases. • Semi-concentric casing-Radius to the outer periphery of the casing and volute area remain constant within a certain angle. • Concentric casing-Radius to the outer periphery of the casing and volute area remain constant through 360°. The degree of concentricity must be reconciled with efficiency, hydraulic radial load, and wear for each specific speed chosen. Up to 1200 Ns the casings can be fully concentric without sacrificing too much efficiency. Above 1200 Ns, the casings can be semi-concentric. The angle of concentricity

Jan 10, 1981

By C. J. B. Dreyer

In terms of resources of amphibole asbestos only South Africa can be considered. There are only two asbestos producing fields, one in the Northern Cape Province producing only crocidolite and one in the Eastern Transvaal producing only amosite. The banded ironstone sequence in which amphibole asbestos occurs is discussed, and the genesis of the fibre is briefly reviewed. The properties and characteristics of amphibole asbestos are discussed and compared to those of chrysotile. Approximately 300,000 tonnes of amosite and crocidolite are produced annually. Crocidolite has a potential for a fivefold increase of production, which could be sustained beyond the year 2000. An estimate of the resources of the various producing fields in South Africa is made. Mining methods are reviewed and evaluation techniques discussed.

Jan 1, 1978

By Zephaniah Varley, Satoshi Akai, Richard Sage, Steve Redmond, Mike Murray, Rohit Shetty, Gerald Skalla

One would be hard pressed to find another project as complex as this one given its configuration, the variety of issues to address and the required construction techniques. Contract C710 is currently under construction as part of Sound Transit’s Link Light Rail, connecting downtown Seattle with Sea-Tac Airport. The paper describes the construction-to-date of the deep mined station under Beacon Hill using the Sequential Excavation Method (SEM). This deep “binocular” station is being mined through some of the most challenging soft ground conditions in the USA. The excavated volume of the station is approximately 60,000 cy (46,000 m3) and the station comprises a variety of geometries and cross sections ranging from 235 sf (22 m2) up to 1,670 sf (155 m2). This underground complex includes platform, concourse, cross-passage and emergency ventilation tunnels together with station egress and ventilation shafts. Various excavation sequences are in use for the different tunnels including the twin-sidewall drifts for the impressive45 ft (13.7 m) wide by 42 ft ( 12.8 m) high concourse cross adits. This station has two train platforms approximately 165 feet (50m) below the surface. This station, constructed in highly variable glacial deposits including water bearing sands and silts approximately 50 ft below multiple perched water tables in an urban setting, creates a very unique and challenging situation. The ground is being managed with various types of ground improvements such as jet grouting and vacuum assisted deep dewatering wells from the surface, and from underground by use of “SEM Tool-box Items” such as barrel vault canopy, grouted pipe and rebar spiling, chemical grout,

Jan 1, 2007

By H. G. Naidu, Raj K. Singhai, S. P. Singh

Introduction The economics of open-pit mining de¬pend heavily on the cost of overburden removal. It is necessary to maintain a pit slope as steep as possible. Steeper slopes lower the volume of overburden to be handled, thus lower the cost of material handling. There is, however, a limit to which the pit slopes in any given situation can be steepened. Steepening beyond this point could jeopardize the pitwall stability, ren¬dering it unsafe. It might even result in curtailment of pit production. Several factors affect the stability of pitwalls. Some are natural, such as topogra¬phy and regional and local geology. Others are man made, such as pit geometry, ground water management, equipment, drilling and blasting, and the type of excavation. Greater control can be exercised in the latter with proper planning and by following a set of procedures based on field experiences. This article deals with one such control¬lable factor - drilling and blasting. The eco¬nomics of steeper pit slopes is discussed, followed by a record of drilling and blasting practices in western Canadian surface mines. Microprocessor-based instrumentation and its application to blasthole drilling is also described. Economics of steeper pit slopes The economics of steeper pit slopes is not a new issue. It should be reinforced, though, that pit slopes must be as steep as possible to ensure maximum recovery of minerals at a minimum stripping ratio. For operating, economic, and safety reasons, different pit slopes are maintained during different phases of pit development. Figure 1 shows a hypothetical ore body, cylindrical shape, with a radius of 225 m (740 ft) and located 30 m (100 ft) beneath the surface. The mining operations are planned at two different slope angles of 25° and 40°. The ultimate pit depth was established on the basis of the criterion of "break even pit." The variation of the stripping ratio at differ¬ent mine levels is shown in Fig. 2. Table I summarizes the eco¬nomics involved for two pit slopes, 25° and 40°. Figure 3 presents the profits during the life of the mine for these two pit slopes. This study shows that steeper slopes for an open pit operation are far more advanta¬geous than flatter slopes. But, what is the optimum slope at any one point in the life of a moving pit? And how can the stable slopes be maintained over the short- and long-term? Canadian blasting practices A survey of blasting practices in western Canadian surface coal mines revealed that, at most mines, hard consolidated overburden is drilled and blasted. Blastholes are drilled with rotary crawler-¬mounted rigs using bits in the 220 to 310 mm-diam (8.5 to 12 in.-diam) range. Typi¬cal hole depths are 12 to 18 m (40 to 60 ft) to accommodate the pit bench heights of 12 to 15 m (40 to 50 ft). For a 12-m (40-ft) high bench, a typical hole will be 14.6 m (48 ft) deep including the subgrade drilling of 2.6 m (8.5 ft). Half of this hole will typically be a powder column and half will be stemmed. For a 15-m (50-ft) bench, a typical hole will be up to 18 m (66 ft) deep including the subgrade drilling. Drilling patterns are usually 9 m (29.5 ft) spacing and 9 m (29.5 ft) burden. De¬pending on local geology and hole diameter selected, drilling patterns of 8 x 8 m, 8.5 x 7.3 m, and staggered patterns of 11 x 5.5 m

Jan 1, 1989

By Jie Zhang, Xi Zhang, Yu Wang, Wei Zhao

The study proposes a novel reagent scheme where adding a small amount of citric acid (CA) significantly improves the depression effect of sodium silicate on calcite and fluorite. The flotation results suggest optimal concentrations for CA and sodium silicate, achieving nearly complete depression of the minerals. Theoretical analysis indicates that CA dissolves calcium ions on the mineral surface, enhancing the adsorption of sodium silicate and preventing collector adsorption.

Mar 27, 2022

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago, there were only a small number of projects that stretched beyond 100 kt/d (110,000 stpd) throughput rates. Today, and moving forward, virtually all the major copper projects are sized beyond this, with throughput rates up to 250 kt/d (275,000 stpd) now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 (5,650 cu ft) flotation cells, through to the 257 m3 (9,076 cu ft) cells and to the current 660 m3 (23,380 cu ft) machines. The contributions of specific copper concentrators to this growth phase are reviewed in this article. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 1, 2014

By D. Dodgen, L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million tom of ash, boiler slag and FGD (flue gas desulfurization - "scrubber") materials as by-products. Utilities and others who bum coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Feb 24, 1997

By Mark Colwell

This paper summarizes the results of a research project whose goal was to provide the Australian coal industry with a longwall installation roadway (faceroad) design methodology that could be utilized by suitably qualified colliery personnel. This goal was achieved in 2012 and the design methodology (and software package) is referred to as Analysis and Design of Faceroad Roof Support (ADFRS). The intended benefits to underground operations, in the provision of this information and resource, are a safer and more productive workplace.

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

By H. Lowers, B. Van Gosen

The Iron Hill (Powderhorn) carbonatite complex is a 31 km2 alkalic intrusion located about 35 km south-southwest of Gunnison, Colorado. The intrusion has been well studied and described because of its classic petrology and architecture of a carbonatite-alkalic complex. The complex is also noteworthy because it contains enrichments of titanium, rare earth elements, thorium, niobium (columbium), vanadium, and deposits of vermiculite and nepheline syenite. In particular, the complex is thought to host the largest titanium and niobium resources in the United States, although neither has been developed. It may be economic to extract multiple resources from this complex with a well coordinated mine and mill plan.

Jan 1, 2007

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By R. Q. Honaker

Dense medium processes are used to clean over 50% of the coal that is fed into preparation plant facilities worldwide. The dense medium is formed using ultrafine magnetite which is recovered after the cleaning step using drain-and-rinse screens and magnetic separators. Despite the high efficiency of the recovery system, magnetite losses of around 0.5 to 1.0 kg/ton are common. Considering the recent escalation of magnetite to around $300/ton, an alternative source of magnetic material from coal combustion bottom ash has been investigated. A relatively low cost recovery system has been developed. Dense-medium tests using the bottom ash magnetics revealed a high level of efficiency as indicated by probable error values around 0.03 over the range of medium densities investigated. The results from both the recovery and coal cleaning efforts will be discussed in detail.

Jan 1, 2009

By M. Menéndez

Enhanced gravity separation appears to be one of the most promising methods for processing all types of <200-µm coal feeds and tailings. Systems based on this technology are reviewed, and the results of investigations based on C900 Multi-Gravity Separator tests conducted to assess the treatment of <200-µm, extremely difficult-to-wash coal settling pond tailings are presented. Multi-Gravity Separator processing tests of ultra-fine tailings with a high clay particle size content (22.6% <10 µm and 60.1% <40 µm) and a 69.56% ash content show that this material can be effectively treated after desliming (<10 µm) of clay-size particles to produce a coal with a 20.6% ash at a separator combustible material recovery of 69.3%. Desliming is shown to be critical in reducing coal ash content and combustible material recovery. Similar improvements are anticipated in the recovery and separation pro-cesses for other enhanced gravity separation systems from the desliming of feeds. Although not a conventional form of treating Multi-Gravity Separator data, the existence of well-defined polynomial relationships based on the product of drum shake amplitude and shake frequency relative to product coal recovery, product ash content and yields at varying wash water flows is demonstrated. Low-amplitude and intermediate- to high-frequency bed agitation are shown to produce optimum ash reduction results.

Jan 1, 2007

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By Andrew J. Petruska, Rik Banerjee

This study explores implementing a machine learningbased system to generate a 3D surface repre- sentation of the roof and support straps in the mine. Event cameras have been chosen for their performance in high-dynamic-range lighting conditions and for their low latency. To enable automated drilling and bolting, 3D vision using eventbased cameras has been developed. A ground-truth set is created using two, time-synced event cameras and a LiDAR camera. These sensors are used to construct a ground-truth dataset of corresponding event- camera images and surface maps from the LiDAR. The network is tested with stereopairs of event images and produces a depth image with ±5 mm RMS error on average across 1000 test images.

Feb 1, 2024

By T. M. Barczak

Pumpable roof supports provide an alternative approach to secondary support in underground mining. Unlike all other supports that are either partially or fully prefabricated prior to being transported into the mine, the pumpable support is fabricated in place in the mine entry. This reduces the underground material handling efforts and thus the injuries historically associated with in-mine support construction. On-site fabrication also facilitates application of the support in areas that are inaccessible to transportation equipment such as scoops or rail cars, making it ideal for many bleeder applications. One of the main advantages of the pumpable support is that it fully bridges from the mine floor to the roof, thereby eliminating the requirement of ?topping off? the support with wooden wedges or crib blocks that soften most other support responses. This report examines the development of modern pumpable roof support technology and provides a full description of the performance capabilities of each of the support products now on the market.

Jan 1, 2008

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986