Search Documents

By D. S. van Vuuren

Titanium bearing resources can selectively be chlorinated at temperatures below 200°C if the Ti02 in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials. A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process. In contrast to previous experience with low-grade titanium-bearing slag containing about 30% Ti02, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300°C and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases. Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln. Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours. Keywords Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By M. Karimi

Artificial neural networks (ANNs) have found their applications in the modelling of unit operations of mineral processing plants. In this research, laboratory-scale tests were conducted, using a three-inch diameter Mozley hydrocyclone. Main parameters included pressure drop at inlet, solid per cent, vortex and apex diameter were adjusted. The corrected cut size (d50c) and the flow rates of underflow and overflow were determined. Multi layers perceptron (MLP) feed forward network architectures were designed to predict the responses. The results showed a good correlation between experimental and network output, for corrected cut size and flow rates. Keywords: hydrocyclone, artificial neural network, corrected cut size, flow rates.

Jan 1, 2010

By D. Grgic, A. Giraud, F. Homand

RESUME : Le comportement mécanique partiellement saturé du minerai de fer a été étudié à partir d’essais de compression simple sur des éprouvettes à pression capillaire imposée par les solutions salines. Les échantillons restent peu saturés (32 %) même pour une humidité relative de 94 %, du fait de la présence de mésopores. Jusqu’à 90 % d’humidité relative la résistance diminue régulièrement. De 90 % à 94 % une forte chute est observée et pourrait être liée à la fois aux effets capillaires et à l’hydratation de certains minéraux. Le cycle hydrique subit par la roche dans la mine a été modélisé en 1D à l’aide d’un code de calcul entièrement couplé pour les milieux poreux partiellement saturés. Les calculs ont montré notamment une diminution importante en paroi des contraintes totales au cours de la phase de désaturation et une augmentation importante au cours de la phase de resaturation. Ces variations pourraient induire un endommagement du massif et être à l’origine d’instabilités, et soulignent l’intérêt d’une modélisation avec une géométrie plus adaptée. MOTS-CLEFS : mines de fer, partiellement saturé, pression capillaire, résistance, modélisation. ABSTRACT : The partially saturated mechanical behavior of iron ore has been studied from uniaxial compression tests on samples in which the suction is imposed with aqueous solutions. Samples are little saturated (32 %) even for a 94 % relative humidity because pores are too large. Up to 90 % relative humidity the strength decreases regularly. From 90 % to 94 % a great decrease is observed ; it could be explained by the capillary effects and the moisturizing of some minerals. The hydrous cycle imposed to the rocks in the mine has been modeled with an 1D fully coupled code for partially saturated porous media. The computations have shown an important decrease in the total stresses at the wall during the desaturation stage and an important increase during the re-saturation stage. These variations could induce a rock mass damage and instabilities, and highlight the necessity of a modeling with a well-adapted geometry. KEY-WORDS : iron mines, partially saturated, suction, strength, modeling. ZUSAMMENFASSUNG : Das mechanische Verhalten von teilweise gesättigten Eisenerz wird durch einachsige Druckversuche untergesucht. Die Prüfkörper haben einen durch Salzlösungen gestimmten kapillarischen Druck. Sie bleiben kaum gesättigt (32 %), sogar bei einer relativen Feuchtigkeit von 94 %, aufgrund der Anwesenheit von Mesoporen. Bis eine relative Feuchtigkeit von 90 % verringert sich gleichmässig die Druckfestigkeit und zwischen 90 % und 94 % merkt man eine starke Abnahme in Verbindung, möglicherweise, mit kapillarischen Effekten und Hydratation von bestimmten Mineralen. Die nümerische 1D Modellisierung des gezwungenen Wasserzyklus im Stein der Mine ist mit einem für porösen Medien ganz vernetzten Rechnungcode geführt. Sie zeigt besonders ein bedeutendes Sinken der Gesamtspannung während der Entwässerung und eine bedeutende Steigerung während der Sättigung. Diese Veränderungen könnten die Beschädigung des Gesteines herbeiführen und die Grundlage von Unstabilität sein. Sie unterstreichen die Wichtigkeit eine Modellisierung mit einer gut geeigneten Geometrie. STICHWÖRTER : Eisenminen, teilweise gesättigt, kapillarischer Druck, Druckfestigkeit, Modellisierung.

Jan 1, 2003

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

The additive property of dispersion variances was found experimentally by D.G. Krige using data from the gold deposits of the Witwatersrand. In this property, called ?Krige?s relationship?, the dispersion of a small unit, v, within the deposit is equal to the sum of the dispersion of v within a bigger unit, V, and the dispersion of these units, V, within the deposit, D. It is known that the variance of the grades decreases as the support increases, the so-called volume-variance relationship. To analyse volume-variance and Krige?s relationship, the methodology herein proposed combines blending piles and geostatistical simulation to simulate the in situ and the pile grade variability. Variability reduction in large piles is based on the volume-variance relationship, i.e. the larger the support, the smaller the variability (assuming perfect mix). Based on a pre-defined mining sequence to select the blocks that will form each pile for each simulated block model, the statistical fluctuation of the grades derived from real piles can be simulated. Using this methodology, one can evaluate within a certain time period the expected grade variability for various pile sizes, and also calculate the Krige?s relationship between the small blocks and the piles of different sizes. A real case study using a large Brazilian iron ore deposit illustrates the methodology and demonstrates the validity of the results.

Jan 1, 2014

By B. K. Loveday, N. V. Ramlall

A study was carried out to evaluate various batch flotation models for the recovery of minerals in a UG2 platinum ore. The major minerals in a UG2ore can be grouped as platinum group minerals, chromite, and siliceous gangue. This study also examined the entrainment of minerals during flotation. The models were ranked using statistical methods and an analysis of model-fit residuals. Entrainment parameters obtained from model fitting were evaluated for logic using a simple mineral-to-water ratio versus time plot. The foremost conclusion from the study was the importance of entrainment modelling. The measurement of water recovery increased the size of the data-set, and the inclusion of a simple entrainment model was statistically significant. The overall fit to the data was improved, and the entrainment model provided logical information on the recovery of gangue minerals that were not considered to be floatable.

Jan 1, 2015

By Antonio Karzulovic, Sergio Olavarría, Patricio Adriasola

The economical analyses of different Chuquicamata open pit mine planning scenarios, indicate that the pit closure should occur at latest in the year of 2017. However, about 60,000 m of drill holes have demonstrated that below the pit bottom there is a potential of 2.3 billion tons of ore. Hence, Division Codelco Norte developed the scoping engineering for a large underground panel caving operation, similar to El Teniente mine. This project considers the exploitation of a 2500 m 300 m footprint, with three 250 m lifts. The plan considers to initiate the construction in the year 2009, to begin the production in the year 2015 and achieve a production rate of 45 million tons per year in the year 2021. A large-scale transition from open pit to underground mining like this one presents three main challenges: (1) to include the geotechnical aspects relevant for mine design and mine planning, (2) to define the proper surface and underground infrastructure, and (3) to fulfil the project deadlines and to achieve the production targets. This paper summarizes this transition project and discusses these three main challenges.

Jan 1, 2006

By P. J. Hancox

Heavy mineral deposits have been known from Liberia since the1950s from both river and beach placers. The heavy mineral content of beach sands ranges between 28?62% and the suite includes ilmenite, rutile, zircon and magnetite. These occur together with kyanite, sillimanite, staurolite and garnet. The average ilmenite content is 82% with minor zircon (11%), rutile (6%) and monazite (1%). The ilmenite is, however, of poor quality with haematite intergrowths and a titanium content ranging from10?42.4% (average ±25% TiO2). The amounts of rutile and zircon, while of suitable quality, have also previously been deemed too low for economic exploitation.

Jan 1, 2000

By N. Kinoshita, Y. Inada

The authors have proposed and discussed storage of low temperature materials such as LNG, LPG and frozen food in rock caverns. In this case, as the rock mass around the caverns will receive effects of low temperature, it is necessary to consider the thermal behavior and the stability of caverns. In this study, strength and deformation characteristics obtained by the uniaxial tension test and the compression test at low temperatures were discussed. Using the results, temperature and stress distribution around caverns when LNG was stored, were analyzed. Then thermal behavior of the rock mass around caverns was discussed. Die Autoren haben Lagerung von Niedertemperatur-Materialien wie LNG, LPG und tiefgefrorenen Nahrungsmitteln in Felskavernen vorgeschlagen und diskutiert. Da in diesem Fall die Felsmasse um die Kavernen den Effekten der niedrigen Temperatur ausgesetzt ist, ist es erforderlich, das Thermalverhalten und die Stabilität der Kavernen zu berücksichtigen. In dieser Untersuchung wurden Stärke-und Deformationseigenschaften, die durch ein-axialen Spannungstest und Kompressionstest bei niedrigen Temperaturen erhalten wurden, diskutiert. Mit diesen Ergebnissen wurden Temperatur- und Stressverteilung um die Kavernen bei Lagerung von LNG analysiert. Dann wurde das Thermalverhalten der Felsmasse in der Umgebung der Kavernen diskutiert. Les auteurs proposent et discutent l'entreposage de matériaux à basse température, tels que le GNL, le GPL et des aliments congelés, dans des cavités rocheuses. Comme, dans ce cas, la masse rocheuse entourant la cavité subit les effets des basses températures, il est nécesaire d'étudier le comportement thermique et la stabilité des cavités. Dans cette étude, les auteurs discutent des caractéristiques de résistance et de déformation, obtenues par essai de tension uniaxial et essai de compression à basse température. En se servant des résultats, ils analysent la répartition de la température et des pressions autour des cavités, lors du stockage de GNL. Ils discutent ensuite le comportement thermique de la masse rocheuse autour des cavités.

Jan 1, 2003

By E. Machaka, A. Cornah

"Mineral resources are typically informed by multiple data sources of varying reliability throughout a mining project life cycle. Abundant data which are imprecise or biased or both (‘secondary data’) are often excluded from mineral resource estimations (the ‘base case’) under an intuitive, but usually untested, assumption that this data may reduce the estimation precision, bias the estimate, or both.This paper demonstrates that the assumption is often wasteful and realized only if the secondary data are naively integrated into the estimation. A number of specialized geostatistical tools are available to extract maximum value from secondary information which are imprecise or biased or both; this paper evaluates cokriging (CK), multicollocated cokriging (MCCK), and ordinary kriging with variance of measurement error (OKVME).Where abundant imprecise but unbiased secondary data are available, integration using OKVME is recommended. This re-appropriates kriging weights from less precise to more precise data locations, improving the estimation precision compared to the base case and to Ordinary Kriging (OK) of a pooled data-set. If abundant secondary data are biased and imprecise, integration through CK is recommended as the biased data are zero-sum weighted. CK consequently provides an unbiased estimate with some improvement in estimation precision compared to the base case."

Jan 1, 2015

By L. Andrews

Keywords: mineralogy, phase-chemical, chemical-looping combustion, XRD, SEM, EDS, QEMSCAN, PGM, slag, matte, ilmenite Mineralogy, traditionally associated with concentrator studies, is being increasingly applied to problems in pyrometallurgy. Such investigations commonly make use of a number of techniques, and the results are combined for a meaningful interpretation, which can lead to a successful solution. Mineralogical applications are described from pyrometallurgical operations. Examples are given of studies and investigations involving mineralogy in chemical-looping combustion, feed monitoring to platinum-smelting furnaces, and losses to slag in base metal and platinum smelting.

Jan 1, 2011

By D. H. Diering

The paper takes the reader into the depths of a modern ultra-deep South African gold mine and gives a perspective on the vertical and horizontal extent of the tunnel networks in such a mine. Depending on the mine design layout employed, tunnels once excavated are subjected to various levels of stress change over their life time, and the support requirements are explained. It is suggested that shotcreting is the only viable ultra-deep level support medium, and after looking at the latest developments, the logistical problems are put forward. In an effort to overcome most of these problems, the South African ultra-deep mining industry embarked on a collaborative research programme in 1998. The importance of tunnelling and in particular tunnel support as a critical technology for future successful ultra-deep level mining is stressed. While not yet fully ?on top of? these problems and challenges, our industry is now fully addressing them and we expect to make significant progress during the next 4 to 5 years.

Jan 1, 2000

By P. H. S. W. Kulatilake, B. Malama

To simulate brittle rocks, a mixture of glastone, sand and water was used as a model material. Thin galvanized sheets were used to create joints in blocks made out of the model material. To investigate the failure modes and strength, both the intact material blocks as well as jointed model material blocks of size 35.6 × 17.8 × 2.5 cm having different joint geometry configurations were subjected to uniaxial and biaxial compressive loadings. Results obtained from the intact model material blocks are used to validate a new intact rock failure criterion for biaxial loading. Results obtained from both the intact and jointed model material blocks are used to develop a strongly non-linear new rock mass failure criterion for biaxial loading. In this failure criterion, the fracture tensor component is used to incorporate the directional effect of fracture geometry system on jointed block strength. The failure criterion shows the important role the intermediate principal stress plays on rock mass strength. Zur Simulation spröder Gesteinsarten wurde ein Modellmaterial aus Dentalgips, Sand und Wasser hergestellt. Daraus wurden Blöcke gegossen, in denen mittels dünnen, galvanisierten Blechen Trennflächen erzeugt wurden. Die Blöcke mit Abmessungen von 35.6 × 17.8 × 2.5 cm wurden in einaxialen und biaxialen Druckversuchen belastet. Es wurde das Versagensverhalten und die Festigkeit von intakten Blöcken sowie durchtrennten Blöcken mit unterschiedlicher Trennflächengeometrie untersucht. Aus den Ergebnissen der Versuche an intaktem Material wurde ein neues Versagenskriterium für biaxiale Belastungen validiert. Die Ergebnisse der Versuche an intakten und durchtrennten Blöcken wurden verwendet, um ein neues stark nicht-lineares Versagenskriterium für geklüftetes Gebirge unter biaxialer Belastung abzuleiten. Darin wird der Bruchtensor verwendet, um den Einfluss der Trennflächengeometrie auf die Festigkeit zu erfassen. Das Versagenskriterium stellt heraus, welche Bedeutung die mittlere Hauptspannung für die Gebirgsfestigkeit hat. Un mélange de platre dentaire, de sable et d’eau a été utilisé pour développer un matériau analogue des roches fragiles. De fines feuilles galvanisées permettent de créer des discontinuités représentatives des discontinuités naturelles dans des bloques fabriqués avec ce matériau analogue. Les modes de rupture et la résistance, tant pour le matériau intact que pour le matériau avec ses discontinuités, ont été étudiés sur des blocs de 35.6 × 17.8 × 2.5 cm soumis à des efforts de compression uniaxiaux et biaxiaux. Différentes configurations de géométrie de discontinuités ont été considérées. Les résultats obtenus à partir des blocs intacts permettent de vérifier un nouveau critère de rupture pour les roches intactes soumises à des efforts biaxiaux. Les résultats obtenus, tant avec les blocs intacts qu’avec les blocs avec discontinuités, sont utilisés pour développer un nouveau critère de rupture, fortement non linéaire, pour les massifs rocheux soumis à des chargements biaxiaux. Dans ce critère de rupture, un tenseur de fractures est introduit pour caractériser les effets directionnels de la géométrie des systèmes de discontinuité sur la résistance des blocs avec discontinuités. Ce critère de rupture démontre le rôle important de la contrainte principale intermédiaire sur la résistance des massifs rocheux.

Jan 1, 2003

By J. P. Piguet, Y. Wileveau

ABSTRACT : An experimental programme for damage assessment was performed in the vicinity of the main shaft of Andra’s Underground Research Laboratory, currently under construction in the East of France, when the shaft is crossing the Kimmeridgian marls between 80 and 100 m depth. The mechanical behaviour was analysed by mean of convergence and displacement measurements. The disturbance into the wall was assessed using numerous methods such as measurement of sonic velocities, permeability measurement and VSP measurement in radial boreholes. The intensity of the damaged zone is low, and its extension does not exceed 0.5 time the radius of the shaft. It does not seem to depend on blasting patterns. ZUSAMMENFASSUNG : Ein Forschungs- und Versuchsprogramm wurde aufgestellt, um die beschädigte Zone im Bereich der Kimmeridgemergel zwischen 80 und 100 Meter Tiefe beim Zugangsschacht des im Bau befindlichen Andralabors im Osten Frankreichs zu berechnen. Das mechanische Verhalten der Formationen wird auf der Grundlage von Konvergenz- und Verschiebungsmessungen ermittelt. Verschiedene Messmethoden, wie z.B. mikroseismische Geschwindigkeite Messungen, Permeabilitäs- und Beschleunigungsbestimmungen in strahlenförmigen Bohranordnungen, erlaubten die Ermittlung des Beschädigungscharakters der Schachtwand. Die Intensität der beschädigten Zone ist niedrig, ihre Ausdehnung übersteigt nicht die Hälfte des Radius des Zugangsstollens und scheint unabhängig vom Schema der Sprengstoffanordnungen zu sein. RESUME : Un programme expérimental visant à évaluer la zone endommagée autour du puits d’accès du Laboratoire de Recherche Souterrain de l’Andra actuellement en construction dans l’Est de la France a été mis en œuvre lors de la traversée des marnes du Kimméridgien entre 80 et 100 m de profondeur. Le comportement mécanique des formations est évalué à partir de mesures de convergence et de déplacements. La mise en œuvre de nombreuses méthodes, telles que des mesures microsismiques, des mesures de perméabilité et d’accélérométrie en forages radiaux, a permis de caractériser l’endommagement en paroi du puits. L’intensité de la zone endommagée est faible et son extension ne dépasse pas 0,5 fois le rayon du puits. L’endommagement semble indépendant des schémas de tirs testés.

Jan 1, 2003

A Seismic Hazard Scale (SHS) has been developed to provide a practical seismic hazard assessment tool applicable to mine site personnel. It has been applied to seismic data sets from numerous Western Australian mines. The SHS is applicable when quantifying seismic hazard on a mine wide scale, on a mining block scale, and on a local cluster-by-cluster scale. Spatial mapping of variations in seismic hazard is a particularly powerful application of the scale. The SHS is sensitive to temporal increases in seismic hazard. It has also been shown that the SHS can be applied to estimate seismic hazard when seismic monitoring data are not available. The SHS is a simple derivation of the Gutenberg-Richter relation. There are assumptions and limitations to the SHS that need to be considered when applying it to mine seismicity data.

Jan 1, 2004

Control of flotation processes is mostly managed by plant operators, who assess the performance of the plant based on their own experience and other heuristic rules. These rules tend to be subjective or ill-defined, since most of them are concerned with the structure of the flotation froth, such as colour, bubble size and shape distributions, froth mobility and froth stability. These phenomena are very difficult to quantify objectively, and inexperience on the part of the operators, human error, etc., can lead to significant inefficiencies in plant operation. In this paper the development of a fuzzy system to support the control decisions of plant operators is described, which leads to significantly smoother control action and more stable plant operation than could be obtained with crisp sets of rules or manual control strategies. Keywords: flotation, fuzzy logic, image analysis, genetic algorithms, rule induction

Jan 1, 2000

By J. E. Davidsen, M. Honstad

"A well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. A worn or short tap-hole channel can lead to more violent flow, significantly increasing the fume emissions during tapping and leading to more metal being mixed with and lost to the slag. Over time, a worn tapping channel might cause side channels and damage to the lining around the tap-hole area. This can result in a burn-through which is a considerable safety risk and will cause significant production losses. At Eramet Norway Porsgrunn, tap-hole maintenance has been done regularly with electrode paste for over three decades with good results. This article summarizes some of the experiences obtained from this practice on a 33 MW SiMn furnace, as well as a change to a coal tar pitch-free binder. IntroductionA well-maintained tap-hole channel is important in order to achieve good and stable furnace operation over time. Metal and slag are regularly tapped from the furnace and may cause a lot of wear on the tapping channel, increasing the risk of lining damage and ultimately leading to a burn-through. On furnace 10 at Eramet Norway Porsgrunn, the tap-hole area is the part of the lining that has been by far the most prone to burn-through since the startup of the furnace.Experience shows that almost all lining problems have started with burn-through in the tap-hole area or in close proximity to the tap-hole. During tap-hole repairs, side channels with metal and slag have also been observed emanating from the main tapping channel. In addition, a shorter tapping channel will cause more violent flow. This can lead to more metal droplets being entrained in the slag, and increase the risk of the furnace not being closed properly at the end of the tap.As a burn-through is a considerable safety risk, and also causes significant production losses, systematic work has been performed over the years to maintain the tapping channel in order to prevent burn-through."

Jun 1, 2019

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By Durell Denysschen, Rafael Abela

The recovery of gold from old mine dumps has been carried out over the last two decades. The gold value and price together with recovery methods, determine whether it is economical to process a dump. Pre-concentration with cyclones and spiral concentrators may offer a method to process dumps considered currently uneconomical to treat.

Jan 1, 2006

By A. P. N. Sutherland

Pipelines for transporting high concentration slurries are often designed using methods applicable to homogeneous non-Newtonian laminar flow. Many industrial slurries though comprise coarse particles in a non-Newtonian carrier fluid, and existing experimental evidence from tests with such slurries demonstrates that they are not homogeneous. Under laminar shear conditions the coarse particles settle, even in statically stable carrier fluids. To understand this better, the Institute of Materials Science and Technology (IMST) at Cape Peninsula University of Technology (CPUT) is conducting ongoing research into the flow of these high concentration non-Newtonian settling slurries. Since pressure gradient and flow rate measurements alone are insufficient to adequately model the flows, an electrical resistance tomography (ERT) instrument developed by the University of Cape Town (UCT)was incorporated into the pipe test loop to determine pipe cross-section concentration and velocity profiles. The software developed to do this is modular and allows different image reconstruction and cross-correlation algorithms to be implemented and tested without significantly changing the rest of the application. At a total frame capture rate of 566 frames/sec a 2.67 GHz Intel Celeron processor with 500 MB of RAM is fast enough to calculate and display velocity profiles in ?real-time? at an update rate of one profile every two seconds. Examples of experimental concentration and velocity profiles obtained using the system are shown and some proposed improvements/extensions to the system are listed.

Jan 1, 2008