Search Documents

By Nareetsile S., J. Kabwe

In the past few years Orapa and Letlhakane Mines have investigated various new technologies to enhance and improve production. The goal has been to improve productivity, reduce operating costs and make the mines more profitable The advent of Global Positioning Systems (GPS) in the early ’80s brought about the realization of this concept. Orapa and Letlhakane Mines started using GPS in 1999 and it is now used atLetlhakane mine for surveying, vehicle tracking and dispatching and for floor control system. Orapa Mine uses GPS in surveying, floor control and drill navigation. It will also be used for vehicle tracking and dispatching in mid-2001 following the installation of a fleet management and control system. The introduction of GPS at both Orapa and Letlhakane mines have improved productivity and reduced operating costs in the areas of drilling, topographic survey and floor control. In vehicle tracking and dispatching GPS has allowed for real-time information management for timeous decision-making which optimized fleet run time hours.

Sep 1, 2001

By Monica M. Cole

The Empress nickel/copper deposit west of Gatooma in Rhodesia occurs within gabbro and amphibolite, disposed at the contact of a granodiorite stock (Barebottom Hill) and the surrounding greenstones of the Archaen Bulawayan System. The orebody has a pipelike form and a poor surface expression due to plantation of the area by Miocene (Africa) and later Victoria Falls erosion cycles. Barebottom Hill represents a monadnock remnant in the geomorphological surfaces while traces of the once larger Empress orebody have been removed. Limitations in soil geochemistry necessitated both studies of the vegetation ecology and the biogeochemistry of the area, both of which were anomalous. The use of geobotany was found to be restricted but biogeochemistry offers a most effective prospecting tool and was found to define the sub-outcrop of the ore-body more precisely than soil geochemistry since these methods reflect and differentiate anomalies emanating from bedrock mineralisation and those due to surface phenomena.

Now a new generation of computerized drill rigs has been launched and they are based on modern standard PC-computer technology. The rigs have been well embraced by the market and more than 100 units have left the assembly line. The new generation has taken a quantum leap forward with respect to drilling accuracy, logging capabilities, reduction of manpower in some types and serviceability compared to the previous generation of drill rigs. The Can bus technology, well proven in the automobile products, is the backbone in the new generation control system of Atlas Copco. The short-term development is now focused on establishing this new automation platform on other product lines of Atlas Copco products. The long-term objectives is to offer the mining industry Atlas Copco products with one common automation platform. Essential for Atlas Copcois to contribute to the work with the on-going Data Exchange standard between mining machines and mining computer systems (IREDES). Our belief is that an accepted standard will make mine automation programs affordable for a wider base of the mining industry, because of the possibilities to a cost effective integration of different equipment with a minimum of system integration problems and machine specific interfaces.

Sep 1, 2001

By B. Hayen

The principal advantages of fibre optics as compared to copper wire are well known and include almost perfect electromagnetic isolation, light weight, small size, excellent transmission security and substantially better bandwidth/distance performance. The decreasing cost of the optical fibre technology (both fibre cable and equipment) has led to another generation of private networks, which provide much larger bandwidths, very high reliability and an increase of the maximum geographical coverage. The larger bandwidth allows to transport all types of information on a single network. Typical communication requirements are speech (audio), computer data, LAN info, control information, video, etc. OTN or ‘Open Transport Network’ is a transmission system based on the latest available technology in fibre optics. It is characterized by the dual ring approach, resulting in high network availability, and the integration of different types of services in one network. As such, it can fulfil almost all transmission requirements for voice, data, LAN, video and any special service required.

Sep 1, 2001

By M. U. Ozbay

The stability of pillars is analysed on the assumption that pillars shed load in a stable manner if the slope the strata load-deformation relation is steeper than that of pillars in the post-peak regime. Concepts of local stiffness, mine structural stiffness, and critical stiffness are discussed. Procedures are described for the determination of strata stiffness for various pillar layouts by use of the available boundary-element computer programs. The postpeak stiffness of pillars is assessed from the available data relating to the post-peak load-deformation relationship and width-to-height ratio. Stability analyses are carried out by the contrasting of strata stiffness with post-peak pillar stiffness. It is shown that the strata stiffness becomes unacceptably small for a stable yield-pillar layout when the span exceeds about 5 times the depth. The strata stiffness is found to increase, thereby increasing the stability, as the span-to-depth ratio, number of pillars, and percentage extraction are decreased. It is also found that the stability in a yield pillar becomes difficult to achieve when al the pillars in a layout are in the descending part their post-peak load-deformation curve

Jan 1, 1989

By J. T. Collins, C. J. Cloete

Secunda Collieries forms part of Sasol Coal, the coal division of the Sasol Group of companies, and already produces 29 Mt of coal per annum from its four collieries: Twistdraai, Brandspruit, Bosjesspruit, and Middelbult. The successful establishment of this mining complex was achieved only through a unique team spirit in which the central services and the decentralized teams under the leadership of the mine management of each of the four mines played an important role. The Secunda mining complex has now reached the optimization phase, during which the mining cost, productivity, safety, and quality of work become as important as production. The setting of priorities and problem solving over the long, medium, and short term are essential for improving the performance of the four collieries. Management had to adapt to the fast-changing environment during the enormously fast build-up of production. The major challenges in the environment were posed by the frequent dolerite intrusions, the extremely hard cutting conditions caused by carbonated nodules and thin sandstone intrusions in the coal seam, and excessive roof and face pressure in some areas due to semi-massive sandstone formations in the rock strata.

Jan 1, 1986

By RT White

For a number of years the steel tube and pipe industry has worked on resolving problems of product quality. These have largely been resolved and new products have been developed to take advantage of new developments. To fully coordinate market acceptance guidance on use of galvanized piping was also required. This was largely achieved locally in 2004 with the publication by the SABS of ARP 060 - Guidance on the use and application of hot dip galvanized steel piping for the transportation of potable water in South Africa. Use of this document is not easy however and a need to have a simple computer model to assist the specifier was identified. Working with a major tube and pipe manufacturer this is now being developed and this paper will provide the background to the model?s development and its intended use. There is still a need for a partner Code of Practice on the performance of galvanized piping in buried conditions and the need for this will be highlighted together with current available information.

Jan 1, 2006

By G. C. Howell, H. A. D. Kirsten

The mining-induced effects around narrow tabular stopes have traditionally been evaluated in terms of elastic continuum analyses. An understanding of the phenomenological behaviour of the rock surrounding deep-level gold mines has accordingly been developed on the basis of such analyses. However, elastic analyses do not afford reliable representations of the behaviour of rock in which failure may occur on discontinuities. This paper describes investigations that show how the stress and stiffness characteristics of a rockmass are affected under such circumstances for representative ranges of values for the relevant parameters (depth, span, support stiffness, field stress ratio, and discontinuity strength). These investigations afford a substantially different understanding of the mechanical behaviour of rock that is subject to failure. Instead of forming an arch across the abutments, the rock in the hangingwall bears directly across the stope onto the footwall and, instead of being subjected to tension, the nether hangingwall is clamped in compression in the horizontal direction.

Jan 1, 1993

By N. Birtek, R. P. King

The washability characteristics of fine South African coals were measured and were found to be well characterized by an M-curve having the equation Z = aQb exp(cQ) x dQ, where Z is the ash content per 100 units of total feed and 0 is the mass yield. Parameters a, b, c, and d were determined for 23 different samples of coal from important coal seams in the main South African coalfields in the size range 0,0025 to 1 mm. The relationship between ash content and relative density was determined and correlated by means of two linear relationships. This characteristic behaviour was explained in terms of the liberation of macerals and the different association between the mineral mater and the two major macerals vitrinite and inertinite. The results obtained in this study can be used to calculate the expected performance of an ideal separation process, and can also be used as input for the simulation of real beneficiation plants. An example is worked through in detail to illustrate the method of calculation.

Jan 1, 1990

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By J. W. Wilson, P. C. Graham

Raise-boring experiences in the gold mines of the Anglo American Corporation Group by J. W. Wilson M.Sc., M.I.M.M., F.S.A.I.M.M., M.A.I.M.E. and P. C. Graham M.Sc. (Eng.) Gold mining is being carried out at ever-increasing depths in South Africa. For reasons of safety and human comfort, it is becoming imperative for raises to be developed by means other than conventional drilling and blasting. Raise-boring is an attractive alternative method. Initial raise-boring experiences in South African gold mines showed disappointingly high costs due to the abrasivity and difficulty of drilling Witwatersrand quartzites. Consequently, a research and development project was instigated with the objective of making raise-boring an economically viable technique in hard abrasive rock. A Robbins 61R raise-borer was made available to the Research and Development team and a number of raises have been drilled. During these trials two advances in cutter design were tested. This paper presents the results obtained, including drilling costs, and provides details of the equipment used.

By L. A. Vermeulen, D. D. Howat

Extensive work was done previously on the wear of grinding media and on the comminution processes operative in bal milling based on the determination of the number-size and mass-size distributions of samples of balls taken from bal mils by a specially designed device. Proof that a sample is as nearly representative as possible of the whole mass of material from which it is drawn is usually extremely difficult. This paper reports a special case in which a direct comparison was made between the number-size and mass-size distributions obtained from a sample drawn from a mil and those from the whole bal charge emptied from the mil. Exposure of the internal defects of the grinding balls caused them to develop irregular shapes after wear had reduced their diameters by about 50 per cent. As a result of the marked change in the morphology of the grinding components, an anomaly was observed between the proportion of small components collected by the sampler and that determined in the total charge. Except for this anomaly, a marked similarity was found in the data relating to the larger components in the sample and the total charge, indicating that the sample obtained by the procedure outlined is representative of the mass of the grinding charge in a mill.

Jan 1, 1989

Duties: The successful applicant will be responsible to the Planning Superintendent for long and short term Mine Planning. The current expansion programme requires production to be derived from new mines, using the most modern equipment. Considerable forward planning is required. Qualifications: Applicants should possess a degree or diploma in Mining Engineering. Experience: Five to eight years' experience in hard rock mining is required of which some part has been spent on mine planning. Conditions: Salary to $7,000. Ample opportunity for further promotion exists in this expanding organisation. The person appointed will be eligible for benefits including discretionary annual staff bonus. An executive home will be provided in the new township with services at nominal rates. Primary schooling is available at Kambalda and the bus service operates for post primary students attending schools at Kalgoorlie. Reasonable relocation expenses within Australia will be met by the Corporation. Employment is conditional upon passing the necessary medical examination for admission to the Western Australian Mining Industry. Written applications, which will be treated in strict confidence, stating nationality, age, marital status and setting out qualifications and experience should be addressed to: The General Manager Operations-W.A., Western Mining Corporation Limited, Post Office Box 80, BELMONT, W.A., 6104. The envelope and application to be marked- "Attention: Senior Mining Engineer".

By J. P. Hugo

Nuclear energy - its interactions with mining and metallurgy - PRESIDENTIAL ADDRESS given by J. P. Hugo Pr. Eng., B.Sc (Eng.) (Rand), Ph.D. (Sheffield) Energy is the life blood of the modern technological era in which we live and it was, I think, Benjamin Franklin who said that the manipulation of energy was the basis of all science and technology. This is perhaps an oversimplification, but there can be little doubt that our life today, and the improved standard of living we aspire to, are governed almost entirely by our ability to generate and manipulate energy. This ability has made it possible for Man - each specimen a feeble twentieth of a horsepower - to travel to the moon, to recover valuable minerals from the depths of the earth, to do arithmetic at unbelievable speed, to lessen the drudgery of manual labour. For these and virtually every aspect of our life we are dependent on energy from external sources. It is, therefore, not surprising that the per capita consumption of energy, and more particularly electricity, has become one of the most reliable criteria by which to measure the standard of living and technological advancement of a country.

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

By D. F. Howarth, F. F. Roxborough

Some important aspects of the design of rock-cutting systems remain relatively unexplored. Two areas of practical significance in this context form the subject of this paper: cutting in jointed or fissured rock, and groove-deepening. A series of controlled laboratory experiments on the performance of disc cutters in jointed rock showed that the spatial and geometrical configuration of jointed rock masses needs to be taken into consideration in the design of mechanized rock excavating systems. One series of experiments showed that, under favourable geometric conditions, the energy required to cut in a jointed rock mass is at least half that required to cut otherwise intact rock. Groove-deepening-the progressive deepening of a groove by successive passes of a cutter-is a potential operational feature with most mechanized rock-excavating systems. Laboratory experiments revealed an important fundamental cycle of events associated with disc cutters when progressively deepening a groove in intact rock. Furthermore, in contrast to pick cutting, groove-deepening by discs is shown to be an efficient operation and one that should not necessarily be avoided. This can be directly attributed to increased interaction between the disc cutters as the result of an increase in magnitude of the lateral forces generated as a groove is deepened.

Jan 1, 1982

By B. G. Meyburgh

SYNOPSIS As a result of a test programme over a period of approximately ten years and a decision to extend the uranium plant, it was decided to design and erect the first full-scale Purlex Plant in the Republic of South Africa. The plant at Buffelsfontein G.M. Co. Ltd. was commissioned in August, 1968, and to date has produced results superior to those predicted in the original estimates. The capital expenditure was R678 000 for a plant capable of treating 1 600 gallons per minute of pregnant solution. Compared with the conventional resin ion exchange process, it has been found that the saving in production costs is 21 cents per pound U3O8 produced. The amine loss is 10 parts per million, which is equivalent to a total organic loss of 250 parts per million. The uranium loss in the raffinate is less than 0.001 g/l U3O8. The final product is of a high quality and it is probable that it is pure enough to convert to the fluoride directly.

By J. W. Wilson, J. G. Taylor

The mechanization of haulage drilling in the gold mines of Anglo American Corporation by J. w. WILSON, Ph. D., C.Eng., M.AIME, F.!.Min.E., F.I.M.M. (Fellow), and J. G. TAYLOR, A.C.S.M., C.Eng., M.!.M.M. (Visitor) Some one-thousand kilometres of tunnels are mined annually in the gold mines of South Africa. Until two years ago, mechanized drilling on South African gold mines was not an economic proposition because of the availability of inexpensive labour and the fact that mechanized equipment developed for other mining markets could not perform satisfactorily in the tough, abrasive quartzites of theWitwatersrand System. A project team from the Technical Development Services Organisation of the Anglo American Corporation, in collaboration with various manufac turers of drill rigs and drill steel, has been concerned with the development of suitable equipment for mechanized main-haulage drilling. After two-and-a-half years of extensive testing and development of drifters, drill steels, and bits, many of the problems encountered have been sotved, and gradually jumbos mounting pneumatically and hydraulically powered drifters are being phased into production on various gold mines of the Group. A description of the development work is given, and actual operating results are recorded, together with details of the drilling and blasting techniques used.

Jan 1, 1975

There are presently no suitable underground mine production scheduling optimisation models available for application to sublevel stope mining. Scheduling underground production for maximum return is therefore still a manual process, which generally involves scheduling production from the next available highest cash flow stope within the operational constraints of the project. In most mining operations, the scheduling problem is too large and complex to guarantee truly optimal results through manual scheduling. This paper reviews some general optimisation studies that have been proposed for underground hard rock mining. Furthermore, an example of a mixed integer programming model is presented for a small conceptual sublevel stoping operation. Comparative results of a schedule generated by a mixed integer programming (MIP) production scheduling model and a manually generated model on a nine stope example is presented. Results indicate that the potential benefits of the MIP production scheduling model for the purpose of maximising NPV are significant. Finally, a new constraint was formulated to limit multiple exposures of fill masses for use in an existing MIP production scheduling model. Testing of the formulation took place on the central stope of the nine stope example, which showed that the formulation performed its task without breaking other operational constraints.

Jan 1, 2007

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979