Search Documents

Toxic gases, mostly carbon monoxide (CO) and nitrous oxides (NOx), are invariably generated by commercial explosives under practical conditions of usage because of oxygen unbalance and non-ideal chemical reaction. Permitted explosives are statutorily required to meet the criteria stipulated by regulatory authority for their toxic fume quality for their safe use in underground coalmines. Solid blasting using P5 explosives contribute around 60% production from Indian underground coal mines. Low pull and yield per blast in solid blasting has been identified as a reason for low production and productivity of Indian underground coal mines. In an effort to improve performance of solid blasting, it was envisaged to apply air decking between suitable P5 explosives using high density polyethylene (HDPE) spacers under a Ministry of Coal, Government of India funded project. A non-deflagrating slurry explosive composition having high air gap sensitivity was specially developed for this purpose, so that air decked cartridges get detonated sympathetically with single priming. However, statutory authority in India apprehended that the use of oxygen negative HDPE spacers can influence the generation of toxic gases. The effect of using HDPE spacers on the generation of toxic gases was studied under simulated laboratory conditions with newly developed as well as with three commercial P5 explosives. The results of studies presented in this paper revealed that the level of carbon monoxide increases linearly and there is no significant effect on the level of oxides of nitrogen due to the use of HDPE spacers with selected explosives. Studies also revealed that this newly developed slurry explosive can be used for air decking up to 15 cm using HDPE spacers of weight not more than 21 g without exceeding the permissible limits for toxic gases.

Jan 1, 2008

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installationof LBs remains a challenge. In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By T. Feroze, B. Genc

"Blind headings in room and pillar coal mines are a major source of methane and coal dust. Most methane and coal dust explosions therefore occur in the blind headings. The primary cause of these explosions is the disruption of the local ventilation system. Line brattice (LB) ventilation systems are used to ventilate blind headings by directing air from the last through road (LTR) into the heading. The amount of air available to ventilate the face of the empty heading depends on the heading dimension, settings of the LB, and velocity of air in the LTR. LBs are commonly installed by underground supervisory staff based on work experience, which may result in ineffective ventilation. The correct installation of LBs remains a challenge.In this study, a validated computational fluid dynamics (CFD) model has been used to analyse the effect of the LB ventilation system variables on the air flow rates close to the face of the empty heading. Full-scale three-dimensional models with various heading heights, heading depths, LB settings, and LTR velocities were simulated. The air flow rates and patterns at various locations inside the heading were analysed. A comparative study was carried out to quantify the effect of each of these system variables on the flow rates close to the face of the heading. Based on the findings, a user-friendly numerical model was formulated that can be used to estimate the flow rate close to the face of an empty heading for different practical settings of the system variables. This model can help the supervisory staff to swiftly implement the ventilation plan according to the regulations and the mine standards. The model can also serve as part of the curriculum for educating future mining engineers."

Jan 1, 2017

By D. Burrows

Traditionally, characterisation of the mineralogy and textures of ore and rock samples were based on observations of hand specimens and thin sections using an optical microscope. The extent of the data collection was limited by the available tools and thus variations in mineralogy and texture were generally not described by quantitative data. These qualitative to semi-quantitative approaches, even though well established over the years, resulted in variable observations and data sets. The data were unlikely to be representative of a sample and limited statistical validity meant the results could not be reliably used in modern digital mining design and planning. With recently developed SEM based quantitative mineralogy tools and the corresponding methodologies, ore textures can be quantified and compared numerically. The numerical data can not only enhance the understanding of an orebody in geological terms, but can also be used in the creation of metallurgical models for mine and mineral processing design and simulation. These capabilities provide valuable inputs to risk assessment studies and the evaluation of mineral projects.

Jan 1, 2007

By J. B. A. Solar Menéndez, M. A. Martínez Fidalgo, L. A. Alvarez-Santullano

1. ANTECEDENTS This present communication refers to the results of the research project entitled "Training in the correct use of chemical oxygen self rescue apparatus and also an analysis of apparatus autonomy", carried out under the auspices of the Specific Collaboration Agreement signed between the Industry Council of the Principality of Asturias (Spain) and INSALUD (National Silicosis Institute, Spain). The antecedents of this project lie in work undertaken by the National Silicosis Institute aimed at optimising efficiency in the use of chemical oxygen self rescuers through improvements in worker training. To be precise, by means of Agreements drawn up between the above-mentioned parties, a simulator was designed and incorporated as the basis of a training station within the " Fundación Barredo" of the Industry Council of the Principality of Asturias. This has been operative since the year 2001 and, up to the present, 2300 Asturian coal mine workers have been trained there. What prompted this activity was the observation of various errors in the use of the self rescuers, deriving from their innate characteristics, especially with respect to the sensation of discomfort - the high temperature and humidity of the breathed oxygen, resistance and inconvenience - and limited autonomy. It was precisely this insight that, in critical situations, lack of familiarity with the conditions of discomfort likely to be experienced during the evacuation process might lead to rejection of the equipment, with fatal consequences, that has justified the setting up of this training and simulation centre. The centre is able to provide all mine workers with the necessary training, and experience of the characteristic sensations experienced when using such equipment (Fig.. 1).

Jan 1, 2003

By X. Jia

The ability to perform three dimensional imaging at micron-scale resolution of real mineral floc sediments and structures using commercially available Micro X-ray Tomography (XMT) instrumentation can be used for the analysis of aggregates and granules, liberation and dewatering of sediments. This paper presents are view of recent work by the authors relevant to the mining and minerals industries. It covers three main topics: X-ray imaging of agglomerates and multi-component mineralic particles,, permeability of sediments, and dissolution of granules with potential application to heap leaching.

Jan 1, 2008

When designing coal mine roof support, it is necessary to account for the uncertainties and variability that inherently exist within the rock mass and support elements. The performance of a support system is affected by these uncertainties, which are not taken into account in the current deterministic design methodologies used in South Africa. The key to the design of a roof support system is a better understanding of roof behaviour and uncertainties that can been countered during extraction. This paper sets out to develop a method that takes all uncertainties that exist within the rock mass and the mining process into account and provides a quantitative risk-based design methodology.

Jan 1, 2009

By M. Kumral

One of the most significant elements in solving the co-kriging equations is the matrix solver. In this paper, the singular value decomposition (SVD) as an equation solver is proposed to solve the co-kriging matrices. Given that other equation solvers have various drawbacks, the SVD presents an alternative for solving the co-kriging matrices. The SVD is briefly discussed, and its performance is compared with the banded Gaussian elimination that is most frequently used in co-kriging matrices by means of case studies. In spite of the increase in the memory requirement, the SVD yields better results.

Jan 1, 2012

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Safety and health can be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard is called AziSA, which means ?to inform? in isiZulu. AziSA provides an architecture that allows for connection of any type of sensor and that is particularly suited to wireless sensing. On the safety side, the CSIR is developing a suite of sensors specifically around the risk of rockfalls. Sensors such as an electronic replacement for the barring tool, or a thermal sensor that can detect loose rock, can already be used to identify potential hazards in the hangingwall. When these sensors are combined with location and time information in a single database, it becomes possible to build maps of risk and to extrapolate risk into unmined areas. It is also easy to confirm that routine safety procedures like barring are actually taking place. In the future, it is proposed that entry inspections will be made using remote techniques that will not place an individual miner at risk. While miners will still be required to bar or place support, they will do so with a clear idea of which portions of the hangingwall are safe, and which present risk. On the health side, if a network such as AziSA is deployed in the stope, it becomes much easier to monitor the condition of individual miners. The work strain experienced by miners can be monitored through heart-rate sensors, and their core body temperature can be monitored using various novel techniques discussed in the paper. Additional sensors can be added to quantify worker exposure to hazards such as noise or dust. Individual sensors allow for people who are at an unacceptably high risk of developing heat disorders to be treated timeously, and they also allow for team management based on objective measures. Over a longer period, position sensing and environment monitors, or personal dosimetry, provide a powerful management tool to prevent workers from being overexposed to hazards, and to confirm that management instructions are being followed. Cost-effective sensing in the stope is a major challenge, but one that can be overcome through technology like that used in AziSA. Sensing provides opportunities both to make immediate interventions when workers are exposed to unacceptable risk, and to manage the long-term exposure of workers to hazard.

Jan 1, 2010

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution, the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallization and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. Furthermore, the autoclave circuit invariably is a high capital cost component of the plant and an area that is carefully scrutinized when debottlenecking and capacity increases are being considered. This paper identifies a unique proven way of increasing the capacity of existing or new exothermic pressure oxidative leach autoclave circuits by as much as two or three times.

Jan 1, 2009

By J. L. Porter

This paper takes a personal look, through the author?s own experiences, at the implementation of innovations in the narrow-seam, hard-rock mining environment of South Africa?s mining industry over the past 40 years. A number of examples are used to illustrate some of the successes and failures over this period. More importantly, the examples are used to illustrate that the bulk of the investment for these projects should have been applied in a manner that could have achieved more sustainable results. The use of the word ?technology? in this context is also examined, as it is the author?s contention that only measuring the performance of machinery fails to encapsulate the potential of the entire system describing the scope of the innovation being implemented. These experiences and observations are projected onto the current backdrop of upheaval in the relationship between key industry stakeholders and the sustainability challenges facing areas of the mining sector in the South African economy. The paper concludes with some opinions on where attention can be focused in order to develop new thinking that can be applied for the safe and economic extraction of the nation?s mineral wealth.

Jan 1, 2014

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as the capacity of the laboratory to process the samples within a given timeframe. In general terms, grab sampling is known to be problematic because samplers tend to over sample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five percent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given with respect to the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2009

By A. L. Edwards

A retrospective study was conducted on the Rand Mutual Assurance (RMA) noise-induced hearing loss (NIHL) compensation claims from 1998 to 2008 to determine if the 2008 milestone agreed at the 2003 Mine Health and Safety Summit was achieved. The number and costs of NIHL compensation claims in different commodity sectors and workplaces were collated. A secondary analysis of the ages of employees compensated after 2008 was conducted. A complementary retrospective analysis of audiogram data investigated the percentage loss of hearing (PLH) shift in different homogeneously exposed groups and occupations at two gold mines. The compensation claims analysis indicated a significant decrease in NIHL claims from 1998 to 2008, but the milestone was not achieved. The reason may be either that claims have not been submitted timeously as required by Instruction 171 and that the current submissions are a result of pre-2003 noise exposure, or that employees who were baselined are still developing NIHL owing to ineffective hearing conservation programmes in place in the mining industry. On the basis of best practice for hearing conservation, recommendations are made for leading indicators in hearing conservation programmes and for reducing the risks of NIHL in order to achieve the 2013 milestone.

Jan 1, 2012

By B. McFadzean, M. Becker, S Geldenhuys, A. Molifie

Mineral hydration is known to result in low flotation recoveries and grades within primary platinum group element ores worldwide. This is because the phyllosilicate minerals derived from hydration reactions of silicate minerals (i) form electrostatic coatings on valuable minerals that in turn hinder collector adsorption, (ii) alter the viscosity of the slurry leading to poor gas dispersion and (iii) decrease the concentrate grade due to naturally-floating gangue. Sodium silicate was investigated because its dispersant, rheology modifying, and depressant properties could prove promising in combating the problems associated with these ore types. Quantitative evaluation by scanning electron microscopy analysis revealed large quantities of serpentine and talc present within the ore sample used in this study, which led to a poor flotation response as indicated by batch flotation tests. Using sodium silicate improved the recoveries and grades at high dosages (>1000 g/t). The zeta potential experiments indicate that improved recoveries are, in part, as a result of the reversal of serpentine surface charge, creating electrostatic repulsion between serpentine and valuable minerals which prevents the coating of valuable minerals by serpentine slimes. Ore dilution and rheology tests indicated that decreased viscosity at high dosages also improved recoveries. Talc micro-flotation tests revealed that the depression of talc occurred at higher sodium silicate dosages, which improved concentrate grade. The processing of nearsurface altered ores is becoming an increasing problem worldwide and the use of sodium silicate proved valuable in mitigating the problems associated with the altered ore investigated in this study. Keywords: Alteration, phyllosilicate slimes, colloidal chemistry

Jan 1, 2020

By P. N. Erasmus

This paper considers the fundamental concepts of support design for underground openings in highly stressed ground. It concludes that the conventional deformed reinforcing bar, woven mesh and cable lacing support methods that have been widely used in deep gold mines are quite in appropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support under rockburst conditions: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit. Duraset in conjunction with SRK Consulting has developed a yieldable steel tendon called the Durabar®. It is unique in the sense that it cleverly utilizes the property of the ductility of ordinary low-carbon steel from which it is made to accommodate the excessive displacement it is subjected to in the case of rockbursts or swelling ground.

Jan 1, 2009

By N. C. Gay

The quantitative evaluation of the performance of fill materials placed in gold mine stopes is achieved by (i) measurement of the in-situ load- displacement, or stress-strain, characteristics of the materials; (ii) an objective comparison between the observed fill performance and that predicted from suitable computer modelling techniques; and (iii) objectively comparing conditions in backfilled and conventional stopes. Considerable problems have been experienced with the development of sufficiently robust instrumentation which can be installed within filled pad- docks and give reliable information over a long period of time. However, at most mines where backfill performance is being monitored, it has been possible to correlate stress measurements within the filled paddocks with strain measurements adjacent to the paddocks. The resultant stress-strain curves agree relatively well with those determined in the laboratory. Measurements in the hangingwall strata of filled and unfilled stopes indicate that the placement of fill does reduce the amount of inelastic convergence due to bed separation. Moreover, in some stopes, the rate of convergence with respect to face advance does reduce to that of the theoretical elastic convergence. Quantification of changes in the conditions at the stope face due to placement of fill has proved difficult. Observations indicate that, provided the fill is placed close to the face (- 5 m), and adequate temporary face support is used, conditions in filled panels are superior. In addition, in filled panels the damage caused by a rockburst in the stope and, particularly, in gullies is generally much less than would be expected in an unfilled stope. To quantify these improvements, parameters such as stope height, face advance and the frequency of falls of ground are being monitored.

Jan 1, 1988

By Paul Fouchè

Contents ?Purpose ?Introduction ?Why manage a mineral resource ?Sampling or tracking from source ?How can RF tracking help ?Project Goals ?RF System ?Tracer Layout ?Antenna

Jan 1, 2005

By André Fouché

GFWW Bulk Sample Prep Plant INDEX ?Features ?Flow Diagram ?Pictures of Plant

Jan 1, 2005

By M. Le Roux

The dewatering of coal, and particularly fine coal, continues to challenge coal prepatration engineers to find a cost-effective solution. With known world oil reserves being depleted daily, it is envisaged that the future price of coal may justify the use of thermal drying to achieve lower coal product moisture levels. The effect of exposure of the coal to elevated toemperatures on the mechanical strength of the coal was investigated. It was found that temperature does not play a major role in determining the volume breakage of a particle and that other variables such as orientation during impact has a much greater influence. A double breakage mechanism was reported during the grindability tests. Surface, as well as volume breakage, occurs for the first 4 minutes while only surface breakage takes place thereafter. Due to this double breakage action, it was found that exposure to temperature does play a role in the amount of breakage and breakage rates during grindability tests. It was also concluded that a particle will break to an optimum size due to impact, after which only its surface will grind away as it is subjected to breakage forces.

Jan 1, 2008

By A. O. Filmer

In the mining and metals industry, business strategy demands that leaders extract more from any set of capital assets. This improvement is achieved through a combination of continuous improvement and upgrading of the assets. Continuous Improvement involves a series of incremental changes in the workplace to stabilize the process, remove waste, and test the limits of process capability. Enhanced Technology involves the replacement of an existing as set with a different process or equipment, to achieve a similar function in a more efficient and effective manner. The paper compares and contrasts the two methodologies and outlines the key business considerations which dictate how and when to select one or other improvement method. The paper also addresses the implications for these two improvement methods for those undertaking R&D in support of the mining and metals business.

Jan 1, 2009