Search Documents

By K. L. Riemer

The West Wits Line first began yielding gold in the mid-1930s and is among South Africa's leading gold-producing areas. Gold mining operations are carried out amidst the occurrence of seismic events which cause both damage to underground excavations and injury and loss of life to production personnel. The feasibility of establishing a system to minotor the seismicity on all the Gold Fields mines was investigated during the early 1980s. This led to the establishment of a centralized seismic network in 1981. The system was structured around three major objectives. It uses Perkin Elmer (now Concurrent Computer Corporation) 16 and 32 bit mini-computers. The hardware in use at both the central and remote sites is outlined, giving a good insight into the role of computers in the system. The system software reveals the fast flow of data through the network; it can be divided into three categories: (1) data logging and transmission - remote sites, (2) data capture and communications - central site, (3) applications and research - central site. Several examples are given which show how the system is measuring up to its objectives. These case studies also indicate how the computers are effective in representing the seismic data collected. It is concluded that the use of computers enables the pin-pointing of seismic events on the West Wits Line within about 3 -4 minutes of their occurrence. The choice of hardware is largely dependent on the objectives of system, and the Gold Fields Network has chosen mini-computers because of the speed of communication and the large amount of data and storage required for research applications.

Jan 1, 1987

By C. A. Snyders

The research presented in this paper investigated the practical aspects of the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were conducted on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of Pt, Pd, and Au were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours, and 100 per cent for Pt, 97.4 per cent for Pd, and 99.9 per cent for Au after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while Ni concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, Ni adsorbs at approximately the same rate as the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. The equilibrium loading of gold is exothermic in nature (Fleming and Nicol, 1984) which will result in an increase in gold elution kinetics with an increase in temperature at similar pre-treatment conditions. A similar result was found for the elution of Pt and Pd. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and results suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing due to increased ionic strength.

Jan 1, 2013

By D. F. Malan, W. J. Theron

Practical mining aspects should be considered when conducting pillar designs for bord-and-pillar layouts. The current methodology for pillar design will result in increasing pillar sizes with depth. This affects the extraction ratio and will result in onerous ventilation requirements when cutting large pillars. A holistic approach, including all mining engineering requirements, is required to ensure that the rock engineering designs are optimized to ensure efficient mining operations and sustainable production. Bord widths should not only be a function of the rock mass ratings, but should also be selected to fit the specifications of the mechanized equipment. The use of a ‘squat pillar’ formula for hard rock is discussed in the paper and the formula based on the exponents of the Hedley and Grant pillar formula, is explored. The effect of abutments and geological losses on average pillar stress is also explored. These factors must be considered when designing layouts at increasing depths.

Nov 27, 2024

By A. R. Javadi

Pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite (ZnS) and galena (PbS) generate hydrogen peroxide (H2O2) when placed in water, with pyrite generating the most amount of H2O2. The order of these minerals for generating H2O2 in water is: pyrite > chalcopyrite > sphalerite > galena. In previous research, the methods of generation of H2O2 in the grinding mill were studied. In this study, data from experiments were included by using MODDE 9 software for six parameters composed of water, grinding media, particle size; adding collector to the grinding, and adding depressant and pH. Finally the optimal condition was achieved. According to the results, most of the recovery is related to the particle 75 μ size and when using processed water, adding 100% collector and without depressant and pH 10. The most recovery of lead in the case of the use of fresh water is in the case of 100% collector, without depressant, pH 10 and 150 μ particle size. Maximum recovery in fraction size 45 μ in the case of water process is 100% collector, without depressant and pH 10. Maximum depressant of pyrite will be the fraction size 75 μ, distilled water, without collector, 100 depressant. Keywords: Sulfide mineral, hydrogen peroxide, flotation, oxidation

Jan 1, 2020

By M. M. Ali, C. Musingwini, R. A. Phillips

The long-term open-pit mine production scheduling problem (OPMPSP) is typically solved in two broad stages. The first stage entails optimisation of the ultimate pit limit, which delimits the economical final pit and maximises the undiscounted value of the deposit. The second stage entails optimisation of the long-term open-pit mine production scheduling, which maximises the discounted value of the deposit. The long-term OPMPSP is a type of an NP-hard problem, such as the travelling salesman problem (TSP), because it is intrinsically complex to solve since it incorporates both hard and soft constraints. Therefore, metaheuristic approaches have been used to find global optimum solutions to the long-term OPMPSP. This paper presents a metaheuristic approach utilising a dual interchange algorithm (DIA) to solve the long-term OPMPSP. The DIA is a parent algorithm which supervises two subservient algorithms, namely, simulated annealing (SA) and Tabu search (TS). The DIA selects the better solution generated in each run from the two algorithms, and simultaneously penalises the algorithm that produced an inferior solution, while rewarding the one that produced a better solution. The DIA was tested on the three-dimensional Arizona Copper Deposit (KD) dataset, which is publicly available for research purposes from the online MineLib repository. It was set to generate net present values (NPVs) in five-minute intervals and the solution improved until it plateaued at about 30 minutes of runtime. The NPVs compared favourably to those obtained on the same KD dataset but obtained over 24-hour runtimes, when solved using simulated annealing and Tabu search algorithms, and the NPV generated from the work of Muñoz (2012) using the modified TopoSort as found on the MineLib repository at the time of this study. Therefore, this paper demonstrates that DIAs can be developed and used to solve the three-dimensional long-term OPMPSP.

Sep 1, 2021

By W. J. Whiten

"Models of cone crushers and vibrating screens are described. These models have been constructed from actual plant data using a systematic model-building technique. Included in this technique is regression analysis using multi-dimensional spline functions.The models have been used to simulate complete crushing plants and hence to design and evaluate a control system for crushing plants."

Jan 1, 2014

By N. Mangesana

The effect of high solids concentration and coarse particle sizes (d50 ranges 90?300 µm) on the viscosity of a suspension of water and silica sand was investigated. The experiments were designed to include conditions that have been tested by other authors and those encountered in the operation of tumbling mills. The rheological data was measured using a tube rheometer with operating pseudo shear rates of up to 1500 s-1. The rheograms obtained depicted dilatant behaviour. The Otswald-de Waele, Bingham, Herschel-Buckley and Casson models were fitted to the experimental data. The Herschel-Buckely model, which approximates the yield point and gives an indication of the shear thinning or shear thickening behaviour of the suspension, was found to provide the best description of the flow curves for all slurries. The Herschel-Buckely model was then used to determine the apparent viscosity of all the tests. The apparent viscosity and yield stress increased with solids concentration and particle size at the different pseudo shear rates. The increase in slurry viscosity with solids concentration was attributed to increased frequency of particle-particle interactions. The increase in slurry viscosity with particle size was attributed to increased inertial effects. At low shear rates the sand slurry exhibited shear thinning behaviour for all solids concentrations. At higher shear rates above 1000 s-1the high solids concentration suspensions exhibited a transition from shear thinning to a shear thickening behaviour.

Jan 1, 2008

By O. G. Motlogelwa

Any company operating a fleet of trucks will be greatly advantaged if the associated fuel costs can be decreased. The optimal tonnage that trucks should be hauling to ensure minimum consumption of diesel fuel has been investigated. The fuel consumption in litres per ton for a fleet of trucks hauling different tonnages of iron ore was recorded in a time-motion study and the optimal tonnage was determined. The following points emerged as a result of the research: > The diesel fuel consumption in litres per ton decreased with increasing tonnage, which means that in order to improve fuel efficiency, the trucks should carry 21 t > As a result of queuing, Africa Truck Hire (one of the two equipment contractors) loses R282.57 per day to diesel that the trucks burn when they are left idling. It is thus advisable that the company adopt a policy of requiring the drivers to switch their engines off while queuing at the stockpile > Filling up the trucks during each shift or rationing the quantity of diesel to 200 litres each shift has a negligible impact on the trucks' fuel efficiency > For the company to spend 35% of their revenue on fuel, the diesel price would have to be between R8.14 and R8.78 per litre.

Jan 1, 2013

FEBRUARY GENERAL MEETING The January General Meeting of the Institute was held in Kelvin House, Johannesburg on 21st January, 1970, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair. There were also present eighteen Members, Messrs M. Barcza, A. R. C. Fowler, R. C. J. Goode, Prof J. de V. Lambrechts, Messrs T. C. A. Meyer, J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), C. A. Border, D. F. H. Grave, S. D. Hill, A. F. Lee, W. L. le Roux, C. S. Macphail, D. L Starkey, S. G. Taussig, W. T. L Wayman and Dr A. Whillier. Three Associate Members, Dr M. I. Brittan, Messrs R. Hemp and M. J. Martinson. One Student, Mr R. P. W. Henrard. Two Visitors, Dr N. G. W. Cook and Mr J. B. Smith. Secretary, Mr D. C. Visser. Total present: Twenty-six. 1. OBITUARY The Vice-President: "It is my sad duty to announce the death of the following members of the Institute: Reginald Gordon McConnell, Member, who joined the Institute on 24th April, 1946 and passed away on 26th September, 1969. James Henry Moore, Member, who joined the Institute on 28th February, 1951 and passed away on 2nd January, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask those present to stand and observe a few moments silence." 2. MINUTES The Vice-President: "May we confirm the Minutes of the General Meetings held on 15th October and 19th November, 1969, as published in the December, 1969 issue of the Journal?" 3. MEMBERSHIP The Vice-President: "I have pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Member: Woodford Anson Gilbert. Associate Members: Michael John Harvey Tonking, Schalk Willem Vorster, Edward Alfred Cole, Johannes Godlieb Bosch. Graduate: Leonard Raymond Kilpatrick. Affiliates: Clive Frere Knight Pouiton, David Philip Ayliff, Kenneth Gillings, Edward Gilbert East. Students: Stirling Graham Low, Petrus Stephanus van der Merwe, Louis Johannes Fourie, Clive Maxwell Winterstein. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: Albert Arthur Hazell, Neville Martin Hayne. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade. 4. GENERAL BUSINESS The Vice-President: "I wish to announce that except for the student prizes awarded at the November meeting, Council has decided to make no awards for 1969. Are there any further matters to raise under the heading of General? If not, we will proceed to the next item on the agenda which is the presentation of tonight's paper. 5. PAPER FOR PRESENTATION The Vice-President: "Professor Starfield may I call on you to deliver the paper entitled "A rapid method of calculating temperature increases along mine airways". After the presentation of the paper, the Vice-President said: The Vice-President: "Thank you very much, Professor Starfield. Gentlemen, I think that many of you here, who have to do with the design of mines in an age where costs and difficulties generally, are increasing at a rate which we find almost impossible to keep up with, I would agree with you that we are fortunate to have a band of people like Professor Starfield, and others who are dedicated to producing the tools, and methods which we need to sort out these problems. I am sure that you would agree with me, that the old rule-of-thumb methods are finished forever, that we can never go back to the methods which served us in the past, when we were close to the surface and had not met the conditions which we are meeting now, and which we are going to meet in an increasing degree in the future. It is to people like Professor Starfield, with these clear, completely logically described new methods, that we look for the solution of our problems in the future. I think the whole problem of layout of any mine, is one where you can reliably prognosticate what you are likely to find in a variety of circumstances to meet the wide range of things which must happen when you consider the costs in these modern operations. Thank you very much, Professor Starfield, for coming and giving us this paper. Thank you for making plain to me how these mathematical models of yours are used. I am sure that what you have said will be a very valuable addition to the archives of this Institution. Thank you very much, indeed, and Gentlemen, will you please show your appreciation in the normal way." (Applause). Professor J. de V. Lambrechts, Mr R. Hemp and Dr A. Whillier then contributed to the discussion. (These contributions will appear in a later issue of the Journal.) PAPERS OPEN FOR DISCUSSION The Vice-President: "Listed on the agenda are papers open for discussion. I would suggest that anyone wishing to contribute to these papers submit their contributions to the Secretary in writing." CONCLUSION The Vice-President: "I wish to thank members and visitors for their attendance, and now declare the meeting closed." The meeting closed at 5.30 p.m

By T. Bohmer, L. Auret, N. Pillay, Z. Horn, P. Rambalee, A. Haasbroek

As part of a broader digital technology-enabled transformation programme, a major mining company is systematically implementing Advanced Process Control (APC) solutions and associated instrumentation throughout their operations. This paper highlights the approach and benefits of this holistic approach for a specific instrumentation installation, and APC installation at a South African coal processing plant. For the coal processing plant under consideration, a systematic approach was followed. Process sections/units are considered from upstream to downstream processing. APC solutions are designed for each process section and each process section is interrogated in terms of availability of sufficient process measurements to ensure stable, capable, and ultimately, optimised performance. Where insufficient process measurements are available, instrumentation upgrades are implemented. Finally, APC solutions are implemented, and evaluated in terms of productivity, safety, health, and environmental benefits. For the flotation section, an opportunity was identified to install froth sensors. The installed froth sensors provide measurements on froth velocity, bubble size, height, colour, and stability. The improved visibility that the froth sensors provided on the flotation process resulted in quick gains in terms of productivity: for example, instability in the feed to the flotation section could be quantified. This resulted in targeted process troubleshooting in an upstream thickener, and subsequent improvement of process stability, and reduced feed variance. The measurements from the froth sensors were further integrated in an APC solution. Proportional mass pull contributions per cell and per line can be inferred from the froth sensors, serving as controlled variables, while pulp level set points serve as the manipulated variables. On-off tests indicated that the advanced process control solution provided increases in yield and product quality.

Sep 1, 2021

By G. Bezuidenhout, N. C. Steenkamp

Buying centres are the first point of contact that determines whether ore will be considered as having sufficient provenance to be considered ethically sourced. The information that needs to be captured on the blockchain platform ranges from reports on in-loco inspections and audits of mining and purchase sites. This will guide passive and active monitoring of mining activities, trade-offs for identification systems, including biometrics for the registration of artisanal sellers, scrutiny on the selection of security measures and companies for buyer centres and stockpiling warehouses, evaluation of active and passive infrastructure security, and remote monitoring applications. Assistance with selection and training in geochemical testing instruments to determine the grade of ore material or concentrates and sorting, on-the-ground investigations, guidance on monitoring methods from stockpile and packing area along the transport route to the final destination are required.

Jan 1, 2023

By E. Lutz, M. Momayez, K. W. Brown Requist

As real-time air quality monitoring becomes more prevalent in US underground mines, it is important to provide the highest data reliability with the fewest possible sensors. Real-time sensors remain costly, and these costs are not exclusively financial; the time required to install, calibrate, and maintain real-time sensors poses a large barrier to widespread implementation. Current atmospheric monitoring systems typically rely on displaying point-specific values. This requires operators to infer real-time airborne contamination distributions. Monitoring and control software utilizing mine ventilation network (MVN) solvers has been implemented in limited cases because of their ability to simulate ventilation systems quickly, but these solvers use a one-dimensional representation of the mine, limiting spatial resolution of estimated distributions. Computational fluid dynamics (CFD) has likewise been considered as a means to improve spatial resolution, but processing times prevent its use as a basis for monitoring and control. For the real-time monitoring of airborne contamination distributions, we propose a spatial interpolation method that can estimate the distribution of airborne contaminants in near-real time. This method provides a middle ground between fast processing times and increased spatial resolution. With the use of a pathfinding algorithm and optimization through absolute percentage error minimization, this method outperforms spatial interpolation with a Euclidean distance. By providing contamination distribution information to operators, this method and its derivatives stand to outperform current atmospheric monitoring systems.

Apr 16, 2024

By F. T. Cawood

Despite economic law and policy instruments with righteous intentions, the politics of resource nationalism could render these instruments unworkable. South Africa is a case in point. After the establishment of democracy, the country's outdated law and policy framework was replaced with a modern system, and in many respects an exemplary one. Converting the privately-owned mineral right system into a scheme of state custodianship allowed for several resource nationalism instruments, in addition to a resources royalty structure that first, compensates for the loss of a non-renewable resource; second, provides for optimal resource use through encouraging value addition to mineral production; and third, effectively targets economic rents. However, despite these improvements, the country went through a process of fierce debate on whether or not mines should be nationalized: the debate was fuelled by public anger with claims of political non-delivery. The result was considerable noise because of public unawareness of facts and distortion of the facts in political rhetoric. The purpose of this article is, first, to establish the status of resource nationalism in South Africa's mineral and fiscal frameworks; second, to give an opinion on the findings of the African National Congress's document on state intervention (Maximising the Developmental Impact of the People's Mineral Assets: State Intervention in the Minerals Sector (SIMS), 2012); and third, to fruitfully contribute to the fundamental discussion on how South Africans benefit from their mineral riches. The methodology is to start with explaining resource nationalism as an international issue for the extractive industries; then to offer an overview of existing resource nationalism instruments in South Africa-along with their effectiveness in attracting rents and investment. The major finding is that South Africa has resource nationalism firmly ingrained in its current suite of instruments. However, it is necessary to address the perceptions of bad governance, and above all, maintain the stability of the rules governing mineral development in South Africa.

Jan 1, 2013

By Y. Ren, B. Yang

The magnetic field characteristics due to electromagnetic stirring in the secondary cooling zone of an extra-thick slab during continuous casting are numerically determined using Maxwell's equations, with particular emphasis on the distribution of magnetic induction intensity and electromagnetic force, as well as the influence of process parameters on the magnetic field. The orientation of the electromagnetic force is the same when the electromagnetic stirrers at the 30° and 60° posistions of the arc-shaped slab are powered in the same direction; otherwise, the orientation is opposite. The magnetic induction at the centre of the section of the stirrer's central axis at the 30° positio, as well as the current, frequency, and fitting formulae, are as follows: B = {0.075I.(1/A)-0.3} mT and B = {-1.75f.(1/Hz)+22} mT. The electromagnetic force and current fitting formula at the central point of the B-B section is F = {0.03168I2.(1/A2)-03.762I.(1/A)+326.7} N/m3, and the fitting formula of electromagnetic force and frequency at the centre point is divided into two segments. The first takes the form of a parabola: = {-21((f-4.3).(1/Hz)2)+970} N/m3, and the second segment is negative linear: F = {-1.65f.(1/Hz)+51.5} N/m3.

Apr 16, 2024

By von Wielligh. L., D. G. Hattingh, M. N. James, W. Thomas

"SynopsisThe process of joining materials by friction is based on generating the heat necessary to create a solid-state mechanical bond between two faying surfaces to be joined. In simple terms, the components to be joined are subjected to frictional heating between rubbing surfaces, causing an increase in interface temperature and leading to localized softening of interface material, creating what is described as a ’third body’ plasticized layer. This plasticized zone reduces the energy input rate from frictional heating and hence prevents macroscopic melting. The plasticized layer can no longer transmit sufficient stress as it effectively behaves as a lubricant (Boldyrev and Voinov, 1980; Godet, 1984; Singer, 1998; Suery, Blandin, and Dendievel, 1994). The potential for this solid-state frictional joining process to create high-performance joints between, for example, dissimilar materials with limited detrimental metallurgical impact, and reduced defect population and residual stress level, has had a very significant impact on fabrication and repair in industrial sectors such as transport. This paper presents a brief overview of the advances made within the family of friction processing technologies that could potentially be exploited in the nuclear industry as alternative joining and repair techniques to fusion welding.Modern friction processing technologies can be placed into two main categories: those that make use of a consumable tool to achieve the intended repair or joint (friction stud and friction hydro-pillar processing) and those making use of a non-consumable tool (friction stir welding). The most mature friction joining technology is friction rotary welding, where a joint is formed between original parent materials only. A new addition in this category is linear friction welding, which opens the potential for joining complex near-net-shape geometries by friction heating. The continuous innovation in friction processing over the last 25 years has led to the development of a number of unique processes and applications, highlighting the adaptability of friction processes for specialized applications for high-value engineering components.IntroductionAssessing the potential for using alternative joining and repair techniques for specific applications in a given industrial sector is informed by an appreciation of the current size and potential growth in that sector. Power generation by nuclear fission has been out of favour over the past few years, due to several high-profile nuclear incidents, e.g. the Fukushima Daiichi nuclear disaster, as well as concerns over disposal of nuclear waste and spent fuel rods. However, due to rapid increases in the demand for electricity, coupled with many fossil-fuel fired plants reaching end-of-life, there is renewed interest in installing additional nuclear capacity."

Jan 1, 2015

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012

[The following notations will be used: O an ore body. z a point in O. z' another point in O. w0 (z) a point support of infinitely small dimensions w0 centred in z. w (z) a sample (or block) of finite dimensions kv centred in z. W (z) a block of size W greater than or equal to w. W'(z) a block of size W' greater than or equal to W. W" (z) a block of size W" greater than or equal to W'. x (z) value of the regionalized variable x with support wO at point z. p (z) average value of x in w (z). pw WZ) = E[x(z')l zt in w(z) pw (z) average value of x in W (z). pwl (z) average value of x in W' (z). pwU (z) average value of x in W" (z). Note that pW (z), pw (z), pwf (z) and pw,, (z) are (regular- ized) regionalized variables with support w, W, W' and W" respectively. The relative sizes of wO, w, W', W" and O are represented schematically in Fig. 7.1. The variance of pw (z) when w (z) takes all possible positions in O is known as the dispersion variance of w in O and is denoted by a? (w in O) or a\: 0; = a2(w in a = Ew,z, inn {[p~ (z) - p121. (7.1) For convenience, the following simpler notation will be used: a> Ew in n [(p w - pl21. Consider now a large block W (z) in O with average value p~(z), and all the possible smaller blocks (or samples) w (z') of size w in W (z). We can calculate the variance of the blocks w (z') in the block W(z), which is the dispersion vaciance of w in W (z), from the relationship a2 [w in W(z)l = Ewcz,, in W(Z) {[PW (z') -pw (z)l21. (7.2) Provided the intrinsic hypothesis is satisfied (§3.4.4), this variance is a function only of the dimensions of the supports w and W, and is independent of the position z of the block W (z). We can therefore define the dispersion variance of w in W, as follows: u2 (win W) = Ew in w [(ptti - PW)~]. (7.3) In cases where the intrinsic hypothesis is not satisfied, the variance of samples w in blocks W may vary only slightly from block to block, so that the average dispersion variance of w in W (z) for all possible W (z) in O can be used: ayw in W) = Ew(,, ~n n {a2 [W in W (z)]}. (7.4) The following example will help to illustrate the importance of the variance of dispersion. Assume that we plan to develop a bedded coal deposit Q. We consider mining the ore body with only one giant dragline, which will extract each day a block of coal of size W'. The total area mined in a year will have a size W". We want to know whether this scheme is acceptable, given that the daily variation in ash content must not exceed a given percentage specified in the sales contract, which is renewable on a yearly basis. On a given day, if we mine the block W' (z), the ash content will average pwT (z). In a period of one year, the expected daily variation in ash content is measured by the expected variance of pwf (z) in W", i.e. by a2 (W'in W"). An alternative mining method might be to use two smaller draglines, each one mining W'/2 of ore per day, and Wn/2 per year. If the draglines are used to mine two distinct sections of the deposit, the expected daily variation in ash content will be u2 (W'/2 in Wj1/2)/2 Other situations, where economic decisions cannot be made without knowledge of the dispersion variance, are illustrated in § 7.4 and 7.5 below. Remark: The notation a2 (w in W) is used in this publication because of its clarity. An alternative notation, which is increasingly accepted in the literature, is s2w/W. ]

Jan 1, 1978

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By M. Arlandi-Rodríguez, and A. García-Berrocal, A. Alonso-Jiménez, C. Lopez-Jimeno

Spain is a major producer of dimension stone, which is one of the most important industrial sectors in the northwest of Spain. This justifies the maintenance of these industries, although the technical and environmental requirements for their continuity are increasingly demanding. The main target of this paper is to present a new methodology in order to obtain k-ratio stress values on the basis of flat jack measurements and finite element numerical back- analysis with Rocscience© RS2 software. Continuous iterations were performed to try to find a relationship between the k₀ and the measured stress in the tunnel roof and sidewalls. It focuses on technical aspects of the method for designing mine chambers in the slate industry that were previously mined by open pit methods. The size of the chambers impacts the operating cost, and the dimensioning of a correct support ensures better efficiency and safety. Correct knowledge of the k₀ therefore is critical for the design of the support. The proposed new method entails a simplification of the classical procedure for estimating the k-ratio.

Sep 1, 2022

By D. Skelton

The Renard kimberlite cluster is located in the Monts Otish region of Quebec, Canada. A Canadian National Instrument (NI) 43-101 compliant resource statement for the Renard kimberlites 2, 3, 4 and 9 and the Lynx kimberlite dyke was first issued in 2008 followed by a Preliminary Economic Assessment and the development of a conceptual mine plan. Following a successful drill program in 2009 that greatly expanded the amount of kimberlite in Renard 2, a revised resource statement was issued in December 2009 comprising 23 million carats of Indicated Mineral Resources and 13 million carats of Inferred Mineral Resources, a threefold increase on the previous estimate. The project is currently the focus of a second Preliminary Economic Assessment and it is expected that a full feasibility and permitting program will commence in 2010 leading to the creation of Quebec's first diamond mine by 2013.

Jan 1, 2010