Search Documents

By S. W. Robertson, M. T. Golela, S. Mxinwa

South Africa has one of the largest Cr-related industries in the world and generates large amounts of Cr-containing smelter dusts. It is normal practice to scrub Cr from the furnace off-gas in water, and to recover the Cr by adsorption, followed by recycling of the loaded adsorbent into the furnace. A study was conducted to find a low-cost adsorbent that is capable of removing sufficient Cr from the solutions generated by scrubbing. The test work focused on the evaluation of different clay minerals (attapulgite, bentonite, and kaolinite) as adsorbents for Cr. Cr(VI) could only be adsorbed after prereduction with e.g. ascorbic acid (ASA). An 80% removal of Cr(VI) could be achieved from a solution containing 20 mg/L Cr using bentonite clay after reduction with ASA. Attapulgite and kaolinite adsorbed less than 55% Cr after reduction with ASA. Both ASA and ferrous salts were found to be suitable reducing agents. The use of acid mine drainage (AMD) was also investigated as a low-cost alternative reducing agent, as AMD usually contains iron. The Cr(VI) reduction potential of the AMD was determined by redox titration against a solution containing 50 mg/L Cr(VI). Studies show that AMD can potentially be used as a reducing agent in a Cr removal process if it is available on site.

Feb 12, 2024

By J. Pelders, G. Nelson

"Fatigue is a significant concern in the mining industry as it is a causal or contributing factor in many incidents and accidents. Fatigue can be caused by work- and non-work-related factors. There is a lack of information about associations between demographic and other non-work factors, and fatigue. This study aimed to assess associations between demographic, work, living, and socioeconomic conditions, and lifestyle characteristics, and fatigue at a platinum smelter in South Africa. Eight interviews with management and two focus groups with production workers were conducted, and 75 questionnaires were completed by production and other workers. Both work- and non-work-related factors were considered to be causes of fatigue. These factors included overtime, shift work, high workloads, activities performed outside of work, age, race, housing tenure, diet, sleep disorders, stress, and job satisfaction. In general, higher levels of fatigue were reported by younger participants, those who rented accommodation, ate less healthily, had a sleep disorder, and those with high levels of stress and low job satisfaction. As various demographic, lifestyle, and wellness-related factors were associated with fatigue, both work and non-work contributors should be addressed in fatigue management plans. BackgroundFatigue may be defined as ‘a state of impaired mental and/or physical performance and lowered alertness arising as a result of, or a combination of, hard physical and mental work, health and psychosocial factors or inadequate restorative sleep’ (BHP Billiton, 2005). Williamson et al. (2011) define fatigue as a biological drive for recuperative rest. Sleepiness and fatigue are related, and the terms are often used interchangeably. However, sleepiness, more specifically, can be defined as sleep propensity, or a person’s tendency to fall asleep (Hossain et al., 2003; Shen, Barbera, and Shapiro, 2006).Increasing levels of fatigue and sleepiness are associated with lapses in attention, errors, response slowing, fluctuations in alertness and effort, and impaired attention, working memory, long-term memory, decision-making, and creativity (Alhola and Polo-Kantola, 2007; van Dongen and Dinges, 2000). Fatigue is also associated with adverse effects on mood and impulsive behaviours (Alhola and Polo- Kantola, 2007; Minkel et al., 2011; Schwarz et al., 2013). It is a significant concern in the mining industry as it is commonly identified as a causal or contributing factor in many accidents and injuries (Schutte, 2009). Fatigue can also lead to long-term health problems, including digestive problems, heart disease, stress, and mental illness (Shaw, 2003)."

Mar 1, 2019

By M. Rossouw

The paper sets out the strategic importance of South Africa?s mining and minerals sector to the national economy. It relates how inexorable and accelerating urbanization and industrialization in emerging markets, especially in China and India, will translate into sustained demand for the minerals that South and southern Africa have in abundance. It warns that while countries buying raw materials from South Africa use these inputs as the basis on which to build value-added, employment-creating industries, South Africa is failing to exploit the economic benefits inherent in its mineral wealth, exacerbating its shortage of skills.

Jan 1, 2011

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By C. Steyn, J. D. le Roux

A dynamic model is used to represent the single-stage closed grinding mill circuit at Mogalakwena North Concentrator. The circuit consists of a ball mill closed by a hydrocyclone. The circuit is modelled according to a semi-mechanistic non-linear dynamic model available in literature. An algebraic routine is used to fit model parameters to steady-state process data. Preliminary validation results against dynamic data indicate that the model is capable of capturing the main dynamic trends of the plant. Since classical system identification techniques proved insufficient to produce accurate models; the non-linear model can be used as a reliable source for model-predictive controller design. Keywords: Grinding, modelling, process control, parameter estimation

Jan 1, 2020

By R. Castro, R. Gómez, F. Betancourt, M. Moncada

In block cave mining, rock fragmentation is a key parameter that influences the production level design and mine planning. Fragmentation occurs mainly by natural breakage during the caving process and in the draw column. The breakage that occurs within the column is known as secondary fragmentation. Secondary fragmentation has been successfully described using the block caving comminution model, which replicates the fragmentation mechanics between particles under drawn and vertical loads in a draw column. This model is based on a kinetic and population balance approach, in which non-normalized and normalized assumptions can be used depending on material and comminution system behaviour. In this paper, the non-normalized and normalized approaches are applied and compared to laboratory data to determine which assumption should be used for secondary breakage in block caving. Approaches are compared graphically, with the mean square error and the Fisher test with a false-rejection probability of 0.05. Based on a statistical analysis, the results show that the normalized model can be applied to all the rock types tested.

Nov 1, 2021

By I. Zemanek, A. Rozsypal

Mrazovka tunnel was excavated under one building whose subsurface space was not possible to reinforce against additional settlements induced by digging. In the presented contribution the risk analysis, warning levels and results of deformation measurements are described. Lespace souterrain d‘un des bâtiments sous lequel le tunnel Mrazovka a été creusé n‘a pu être renforcée contre l‘affaissement supplémentaire provoqué par l‘emplacement du tunnel. Le matériel présenté décrit l‘analyse des risques, le niveau des limites et les résultats des mesures des déformations. Der Untergrund eines der Gebäude, unter dem der Tunnel "Mrazovka" ausgeschachtet wurde, war es nicht möglich, gegen nachträgliches Setzen zu versteifen, hervorgerufen durch die Untertunnelung. Im vorliegenden Beitrag sind Gefahrenanalyse, Grenzwerte und Ergebnisse von Deformationsmessungen beschrieben.

Jan 1, 2003

By R. Pipeleers

Recent experience has shown that all underground workplaces in the Campine Coalfield in Belgium will require controlled cooling within three years. Considering the socio-economic and legal importance of the climatic problems underground, IREA has undertaken studies in forecasting the climate of future workplaces, planning the necessary cooling equipment and optimizing efficiency in the existing cooling equipment. These studies are being carried out using the climate forecasting program of Bergbau-Forschung. So far, the German model has been obliged to utilize manually measured data from a few workplaces in the Campine. As the model does not fit very well with these measurements, it has been thought necessary to' develop a system of continuous data acquisition and transmission. This system is being tested in the Beringen mine of the N.V. Kempense Steenkollenmijnen. In the first part of this paper the digital tranmission system is described; in the second the sensors used to collect the necessary climatic data are presented, and in the third some results are given.

Jan 1, 1987

The two methods for calibrating the parameters K and (alpha) for use in Gy’s equation for the Fundamental Sampling Error (FSE)–, Duplicate Sampling Analysis (DSA) and Segregation Free Analysis (SFA)–, are described in detail. A case study using identical broken reef material from a Witwatersrand-type orebody was calibrated using the DSA and SFA methods and the results compared. Classically, the form of Gy’s equation for the FSE raises the nominal size of fragments given by dN to the power of 3. A later modification of Gy’s formula raises dN to the power (alpha), the latter term being calibrated with the coefficient K in the DSA and SFA methods. The preferred value of for low-grade gold ores used by sampling practitioners in the mining industry is 1.5. A review of calibration experiments for low-grade gold ores using the DSA and SFA methods has produced values of K that vary between 70 and 170 and values of in the range 0.97 to 1.30. The average value for is shown to be 1, rather than 3 as originally proposed in the classic form of Gy’s equation or the industry-preferred 1.5. It is suggested that for low-grade gold-bearing ores the equation for the FSE should raise dN to a power of 1. Such an equation for the variance of the FSE greatly simplifies the characterization of gold ores, now requiring only the calibration of K for a given mass and established fragment size. The implications of the simplified equation for the heterogeneity test are that, provided the fragments have been screened to within a narrow size range, any particular size will return a value for K that is acceptable for use in the sampling nomogram.

Jan 1, 2017

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By X. Zhang, Z. T. Yuan, C. Zhang, H. M. Zheng, X. M. Wang, L. X. Li, N. Li

In metal mines, comminution is commonly used to liberate minerals for subsequent mineral concentration processes, such as flotation, magnetic separation and gravity separation. However, ores are aggregates of valuable minerals and their disseminated gangue minerals, and these minerals exhibit diverse comminution behaviours. In carbonate-bearing iron ores, hematite, siderite, and quartz are the predominant minerals, of which hematite is the objective recoverable mineral. In this regard, the present study aimed to identify the imperfections in siderite minerals by X-ray computed tomography (XCT), and thus quantitatively characterise their size and shape in terms of Feret diameter and aspect ratio, as well as other parameters. XCT images indicated the protogenetic ubiquity of pores <5 μm in diameter and cracks of 7-8 μm inside siderite particles. In the ground product of artificially mixed siderite and hematite, siderite particles were smaller than hematite particles. Siderite particles had a larger surface area and greater surface roughness than hematite particles of the same volume, which was attributable to the intrinsic holes and cracks in siderite particles. This study provides an insight into the relationship between the inherent imperfections of minerals and their comminution properties. Keywords: Siderite; X-ray computed tomography; particle imperfections; grinding behaviour; sliming

Jan 1, 2020

By F. Samimi Namin

One of the main tasks in exploitation of mines is to select a method suitable for the deposits, specific features including geometric, geo-mechanical and geological features. The purpose of selecting a mining method at this stage is to choose one or more method(s) having the most coordination with the deposit?s conditions and external factors, including the allocated budget and local technology for detailed feasibility studies. Several methods have been developed in the past to evaluate suitable mining methods for an ore deposit, based on its physical characteristics. These approaches can be classified into three groups: (1) profile and checklist methods, (2) numerical ranking (scoring) methods, and (3) decision-making models. Most of these methods have shortcomings. Considering the fact that most of the specifications of mineral deposits, such as dip and depth, are linguistic variables, absoluteness of the explaining parameters by previous methods can be mentioned as the most important disadvantage of these methods. This paper discusses the Fuzzy technique for order performance by similarity to ideal solution (Fuzzy TOPSIS) to determine the mining method. The fuzzy decision making (FDM) software tool is employed to develop a Fuzzy TOPSIS based model. Application of this model with various values (crisp, linguistic and fuzzy) of the deposit eliminated the existing disadvantages of other methods. Two empirical illustrations demonstrate the effectiveness and feasibility of the evaluation procedure. These show that the proposed model performs better than its alternatives. Keywords: mining method selection, fuzzy TOPSIS, decision making, mining engineering, linguistic variables.

Jan 1, 2008

By B. Hart, B. K. Gorain, A. Chattopadhyay, S. Dimovc

This paper presents a detailed and systematic approach to metallurgy diagnostics using an integrated novel gold deportment technique for complex copper-gold and refractory gold ore bodies. This uantitative gold deportment for these complex ore bodies is a challenging task due to reasons such as lower grades, high variability of visible and invisible gold content in different sulphides and iron oxide phases, significant presence of disseminated and composite carbonaceous matters along with associations of various copper sulphide phases. Gold mostly occurs as "invisible gold" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulphides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Studies were initiated on various complex ore deposits and also on samples representing various process streams. Some case studies are presented in this paper to demonstrate the value of a high confidence gold deportment methodology in developing insights for problem diagnostics and to identify opportunities for metallurgical improvements. A systematic and holistic approach involving different fields of expertise is critical for successful development and delivery of solutions for complex ore bodies. Keywords: Integrated gold deportment, complex copper-gold ores, double refractory gold ores, carbonaceous matter, diagnostic metallurgy, preg-robbed surface gold

Jan 1, 2020

By J. J. Botha

As a Demand Side Management (DSM) Project, money was granted for the procurement and installation of a 3-Chamber Pipe Feeder System (3-CPFS) at AngloGold Ashanti?s Moab Khotsong Mine in the Vaal River Area, Orkney. The first submission was done to ESKOM in December 2002 and the contract was signed in September 2006 at a cost of R 57-million with an envisaged reduction in power of 7 Megawatt per month based on a 90% utilization factor. The project was finally commissioned in December 2008. The technology is not new, but the intent of the paper is to share with others the experience gained by using the technology in a deep-level mine in order to reduce overall power consumption.

Jan 1, 2009

By A. S. Macfarlane

"SynopsisMetal accounting and reconciliation is an increasingly important governance issue in all mining operations, in that it is required, from a risk management perspective, that the company is in control of its product throughout the whole mining value chain. Reconciliation is a grossly misunderstood term. It means different things to different people, and therefore one of the purposes of this paper is to ensure a holistic and integrated understanding of ‘reconciliation’.Previously, where reconciliation was done, it was often for internal control purposes and loosely applied, sometimes with a low degree of confidence and understanding of the underlying parameters and their natural variability.In most mining operations, issues such as dilution, stope performance, and recovery are critical to profitability and long-term value, and thus understanding and control of these key value drivers is essential, not only from the governance perspective, but also from the perspective of maximizing shareholder returns. In order to implement a system for metal accounting and reconciliation, it is important that the cause and effect of these value drivers is understood, and that a systematic control system be established.While a number of off-the-shelf solutions exist for this work, it is the contention of this paper that a full understanding of the metal flow, its variability, its underlying loss potential, and its control points is necessary before a systematic approach to reconciliation can be undertaken.The paper also advocates that this approach should ensure that the reconciliation system clearly addresses the reconciliation needs, within a consistent framework. Such a framework has been developed by AMIRA, in terms of a metal accounting code. However, up until now, this code has been aimed at plant processes, whereas this paper shows how the concept can be extended to cover the full reconciliation requirements for a base metal mine.IntroductionReconciliation is defined as ‘the process of finding a way to make two different ideas, facts, etc., exist or be true at the same time’. In terms of a mining process, this refers to the comparison of measures and estimates along the value chain, and at different points in time, in order to track and optimize metal recovery. This leads to the notion of having a system in place for accounting for the metal. The University of Cape Town defines metal accounting as ‘… the estimation of (saleable) metal in a mine and subsequent process streams over a defined time period. Comparisons of estimates, from different sources over a specific time period, are called reconciliation.’Traditionally, metal accounting has consisted of geological reconciliations of mineral resource to mineral reserve conversion, mine planning reconciliation related to the reconciliation of long-term plans to short-term plans, grade control reconciliation of head grades to sampled or block grades, and mine survey reconciliation of tonnage discrepancies and mine call factors. In addition, metallurgical reconciliation has tended to be based on metal balancing, followed by some commercial metal accounting that links dispatched product to sales quality, quantities, and revenues. Miners disparagingly refer to this plant process as ‘millmatics’."

Jan 1, 2015

By V. I. Ryaboy, V. P. Kretov, I. V. Ryaboy

Attachment of collectors containing thioamide groups to sulfide minerals is interpreted as interaction between NH-acids and sulfides acting as solid bases with the formation of a donor–acceptor reagent–mineral bond. As the acid function of the reagents increases, their sorption optimum is observed to shift to a less alkaline region. The developed concept has enabled us to propose a method for calculating optimal pH values for the sorption of reagents on mineral surfaces depending on the acidity of the reagents and the pH value of the medium. Our estimates correlate well with the experimental data. We studied the spectra of the reagents containing thioamide groups and the spectra of copper salts and their surface compounds on an oxidised copper film, chalcopyrite, and pyrite using the infrared (IR) spectroscopy. Some effective applications are described of reagents containing thioamide groups in the flotation of copper, copper-molybdenum, and gold ores, both separately and in combination with other collectors. It is shown that the flotation performance is maximised by adding two- and three-component collector combinations, including collectors containing thioamide groups. In this case, the increase in the recovery of copper, molybdenum, and gold is up to 2-5% compared to conventional process conditions. A new, high-performing reagent containing a thioamide group is proposed. A commercial pilot batch of the reagent was produced and sent for flotation tests in gold ore applications. Keywords: Thioamide reagents, dialkyldithiophosphate, collectors, flotation, arsenopyrite, chalcopyrite

Jan 1, 2020

By J. A. Kinnaird, B. J. Youlton, K. L. Youlton

Methods for treating and processing refractory gold ores are well established. However, what is less well understood is how the formation of the gold-bearing deposits affects gold processing and extraction. In order to evaluate the effect of ore genesis on gold extraction a number of South African gold deposits were studied. These included complex Pilgrim’s Rest samples as well as refractory Fairview, Barbrook, and Consolidated Murchison samples. We found the refractory nature of gold ores is controlled by a limited number of well-understood mineralogical factors. Solid solution gold is linked to low temperature and pressure conditions in fine-grained sedimentary lithologies, while reactive pyrrhotite can form from hydrothermal fluids associated with mafic magmatic rocks. These formational controls can be used to identify and avoid complex deposits at a desktop study phase, or address and reduce complications further along the pipeline using early mineralogical studies.

Jun 1, 2021

By M. Abdellatif

"SynopsisCalcined basic nickel carbonate (BNC) concentrate was smelted in a pilotscale DC arc furnace to produce a nickel metal. The furnace was continuously operated for 12 days (24 hour/day), during which twelve different smelting conditions were investigated, with the major variables being reductant type and feed rate, flux composition and addition, and BNC feed rate.The 200 kW DC arc furnace was operated at power levels between 110 and 165 kW and at a total feed rate of 78 to 96 kg/h, resulting in an average slag and metal tapping temperature of about 1650°C. A total of 7.2 t of BNC were smelted, producing about 5.44 t of nickel metal and 2.94 t of slag. Nickel recoveries of 96.4% and higher were achieved, and the slag nickel content was as low as 0.1%. The major impurities in the metal were iron (mostly from oxygen lancing) and carbon. The calculated feed carry-over was less than 0.85% and the graphite electrode consumption was between 2.8–3.3 kg/MWh.IntroductionOne of the most distinctive advantages of DC open-arc smelting is the ability to process fine raw materials without any major issues with regard to the operability of the furnace, metal recovery, and metal quality. This has been demonstrated in Mintek’s DC arc pilot plant facilities over a period of about three decades (Curr et al., 1983). The materials that have been processed include laterite (Kotze, 2002), chromite fines (Curr et al., 1983), manganese fines (Lagendijk et al., 2010), PGM concentrates (Shaw et al., 2013), electric arc furnace (EAF) dust (Denton et al., 2005; Abdellatif, 2002a) and stainless steel (SS) dust (Denton et al., 2005; Abdellatif, 2002a; Goff and Denton, 2004), and petroleum fly ash (Abdellatif, 2002b). The top particle size of such materials can vary from a few millimetres (e.g. laterite) to micrometres (EAF and SS dust). Dusting, whether due to physical carryover of feed or to the arc side reactions, has been proven to be a non-issue. As such, the applications of DC open-arc furnaces have the potential to be extended to other raw materials such as particulate nickel oxide, which has a particle size much less than 100 µm.Nickel oxide is typically produced from laterite ore by sulphuric acid leaching, purification, and precipitation as basic nickel carbonate (BNC) (Rhamdhani, Jak, and Hayes, 2008) or as mixed hydroxide precipitate (MHP) (Mackenzie, Virnig, and Feather, 2006), and finally calcining at moderate temperatures (800–1200°C). The NiO product is very fine, with an average particle size in the range of 10–20 µm and a NiO content of more than 99%."

Jan 1, 2015

By C. Montoya

This paper shows, through a case study, the impact of multivariate grade modelling upon mine design and mine planning. A deposit explored by drill holes is considered, in which the grades of five elements (copper, silver, molybdenum, arsenic, and antimony) are of interest. Forty alternative models of the deposit are constructed by fitting the joint correlation structure of the grade variables and using conditional cosimulation. In addition, a reference model, obtained by averaging the alternative models, is also considered. The study shows that the resulting mine design (final pit characteristics and production schedules) is sensitive to the grade model under consideration, and that the design based on the reference model may not be optimal when compared to the alternative models based on cosimulation. However, when assuming a given long-term plan and extraction sequence, the grades and net present value (NPV) calculated on the reference model are unbiased with respect to those calculated on the alternative models with the same extraction sequence. The latter allow assessing the possible dispersion of the actual grades and NPV around their expected values, and are useful for the planner in order to determine the probability of meeting given production targets and of exceeding or falling short of given threshold grades. Additionally, unlike cosimulation, the separate simulation of each grade variable leads to unrealistic resource models and to biased results in mine design and mine planning. This approach should therefore be avoided, unless the grade variables are spatially uncorrelated.

Jan 1, 2012

By D. Borman

The location of underground positions in mines has usually fallen to their survey department&apos;s. Their usual tasks include: ? installation of a high-precision peg network like the National Survey grid as beacons ? offset measurements to the sidewalls, and sometimes hangingwall and footwalls, of development tunnels and excavations ? offsetting of stoping panels for the calculation of face ? advance and the square meterage of area removed. Other departments build their observations into the plans produced by the surveyors. If more precision is required, they ask the surveyors to `elevate&apos; their points with a theodolite. Apart from the survey peg network and `elevations&apos; these measurements are usually planer measurements suitable for producing plans, sections and projection sheets. When the only representation medium was a sheet of paper or transparency, this was perfectly suitable. However the development of CAD models of the workings has changed all this. Full 3D representation is not properly catered for in the tool sets in current use, and needless hours are spent converting analogue-type observations into digital form. The basic survey models need to be augmented by the observations of other disciplines that are also required to locate positions underground. These include: ? the need for geologists to plott their mapping and ? borehole logs into 3D space ? the need for samplers to position their sample points accurately because the geostatistical models are biased and inaccurate ? the need for stoping width recorders to position their thickness observations to prevent errant evaluation and bonuses ? the need for rock engineers to place their mappings into 3D to build true geotechnical models to manage geotechnical stresses ? the need for production officials to receive updated face ? positions during the month so that they can manage the ? production and utilize their resources properly. This paper covers a new method of positioning profiling points to a suitable degree of accuracy. I believe the method is sufficiently simple and cheap for all to use. Historical methods Platinum and gold orebodies, especially in South Africa, are generally narrow tabular deposits. This made them suitable for depicting on a 2D medium like paper. The determination of stoping or face widths was not a problem, as the ore is removed in a single stoping process. Such 2D representations could be easily positioned using tape offsetting between survey pegs or points tied in from survey pegs. Problems of dip were handled by using &apos;Stope Sheets&apos; which chose a best fit projection for the whole area depicted or by using true dip section sheets for inclined tunnels. Rolling reef and potholes were the common areas of difficulty. Most mines now model their orebody and plan the extraction in computer graphics. This means that the representation of the current workings has to change to support this trend. It now becomes a truly 3D problem. Mining officials find it inconvenient to have their actual workings in single-line depictions while their orebody is depicted with top and bottom contacts and the planned tunnels in 3D shapes. Geological models which form the basis for the resource model and planning process are often out of date, as the updating process is slow. The geological mapping has to be plotted onto sections and plans. These are then digitized into graphics by a draughtsman and checked by the geologist. Only then does the interpretation and model update take place. Potential methods to create 3D &apos;Actuals&apos; Global positioning systems (GPS) Surface mines have been blessed by the advent of GPS technology. These simple-to-operate pieces of equipment and compatible software make it possible for all types of mine employees to locate themselves, and therefore to locate their observations. GPS are often inexpensive and give an acceptable degree of accuracy. Only in deep pits or close to the highwalls are observations hindered. Such technology cannot however, work underground. Ground penetrating radar (GPR) GPR is reported to be very useful for estimating the positions of potholes and faults. However it is still considered as providing an estimate, not a definite measurement. GPR is good for seeing into solid rock, not into open spaces. Inertia reading devices Experiments with inertia reading devices have been conducted on the mines. They were the forerunners of GPS for military guidance systems, and were even used for city navigation in the early 70s. They do however work best with heavy or fast-spinning gyros. Anglogold Ashanti&apos;s attempt to use them were discontinued in the mid-90s when the developers asked for an additional few million rand for a device that would weigh more than 12 kg and have a limited operational life.

Jan 1, 2006