Search Documents

By L. M. Chan, D. R. Carlson, J. H. Johnson

"This paper presents an apparatus and procedures to implement a methodology for controlling ambient air quality in a confined working environment, such as an underground mine, an underground storage area, or a tunnel. The air quality control methodology is directed at limiting the quantities of exhaust pollutants emitted by diesel-powered vehicles into the confined space by identifying vehicles that are excessive polluters. The methodology is based on tailpipe and ambient air measurements in the confined space, and the ambient air threshold limit values (TLVs) for the various diesel exhaust pollutants. The methodology consists of two computational methods; a deterioration criteria computational method to identify excessive polluting vehicles, and an engine performance computational method to determine engine performance and to provide information needed to diagnose engine faults. The methodology is designed for implementation in conjunction with a preventive maintenance program.The first part of the paper describes the mine air and tailpipe emissions measurement apparatus and techniques used to obtain data. This is followed by sections discussing the deterioration criteria and the engine performance computational methods. A section discussing some common engine emissions-related faults is also presented lastly, a proposed procedure to implement the methodology including a possible hierarchical structure for mine personnel involved to implement the procedures is presented.INTRODUCTIONDiesel-powered mining vehicles are gaining Popularity in underground coal mines and are almost universally used in underground non-coal mines due to their mobility, flexibility, and higher productivity. However, noxious gases and particulate matter in diesel engine exhaust are a concern because of the potential for being harmful to the health of miners. Diesel exhaust pollutant concentrations out the tailpipe of a mine vehicle change with time due to engine wear, inadequate maintenance, improper adjustments and other factors. This deterioration in pollutant concentrations, if not properly controlled, may adversely affect the air quality in an underground mine. To provide assurance that a clean and healthful work environment are maintained, a program is needed to identify and repair diesel engines that contribute to poor air quality. Also, earlier detection of deteriorated engines will make preventive maintenance possible, thereby eliminating further deterioration and possibly complete breakdown. Preventive maintenance also increases engine life and equipment availability in production which in turn will result in decreased operating costs."

Nov 1, 1995

By W. K. Overbey

Knowledge of fracture systems in oil or gas reservoirs is essential to the efficiency of both primary and secondary production operations. A relationship was established between structural features of the surface and both natural and induced fractures in oil and gas reservoirs, thus providing a method of predicting the direction of rock fracture prior to field development and well completion. Correlations between the surface features and under-ground fractures resulted from analysis of joint strike measurements, bottom-hole impression packer surveys, photographs of hydraulically fractured wells, fracture data from oriented cores, in situ strain measurements from formation outcrops, and lineament analyses from aerial photographs. The mean orientation of surface fractures, lineaments, and stress field directions ranged from N 53° E to N 73° E, compared with an average orientation of N 63° E for the hydraulically induced fractures. Tectonic stress field was shown to influence the direction of hydraulically induced fractures. This report presents the details and application of techniques to obtain the orientation of the principal horizontal compressive stress field component and thus the direction of induced fractures.

Jan 1, 1971

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

By Willard L. Hunter

The Bureau of Mines smelted samples of chromite ore and concentrate from the General Services Administration (GSA) purchasing depot at Grants Pass, Oreg., in a submerged-arc furnace to establish smelting conditions and the energy requirement to produce high-carbon ferrochromium. Raw material, in the form of ore, flux, and reductant, and electrical energy are available on the Pacific coast to smelt the chromite. The concentrate can be smelted without prior agglomeration by employing hogged wood (wood chips) as a major portion of the reductant. The energy requirement is relatively low, about 3,960 kw.-hr. per ton of alloy. The ferrochromium produced will contain about 60 percent chromium. In addition to the smelting data, a statistical summary of the grade and amount of chromite purchased during the stockpile program and estimated chromite reserves and production volume are given. It is estimated that 632,000 tons of Cr203 contained in chromite of all grades is available in the western coastal States. Of this total there appears to be sufficient metallurgical-grade and beneficiable ore to sustain a smelting operation for 25 years at a consuming rate of 25,000 tons a year, utilizing material comparable to that delivered to the Government stockpile.

Jan 1, 1961

By H. M. Lawrence

"In the land-pebble district of Florida a lively interest in the possibilities of obtaining increased recoveries of phosphate rock is evident. Research in several directions is being carried on by companies operating in the district to increase the yields obtained by the washing plants. The Bureau of Mines is cooperating with this research program to promote more efficient plant practice and to avoid unnecessary depletion of mineral resources.Washing practice, as carried on in the district at present for the recover of phosphate rock from the crude ores or matrix, is not a complicated process. Flow sheets of the several companies are similar, although the equipment varies with the preferences of the individual operators. For disintegrating the matrix log washers are favored, although revolving drums equipped with flights to break up lumps of clay are also used. Fine sand is removed by screening. Vibrating screens have become well established in the district, although stationary flat screens and trammels are also employed.The writer acknowledges with appreciation the cooperation of the phosphate companies in the land-pebble district; suggestions and criticism by Will. H. Coghill, supervising engineer, Ore Dressing Section of the Bureau of Mines; and the laboratory assistance of J. O. Davie, J. W. Pamplin, and E. Roca, cooperative fellows of the University of Alabama.Losses in the Finer SizesOf the phosphate that is not recovered by present washing methods the greater portion is in the finer sizes. In these sizes the phosphate grains are accompanied by grains of sand - largely quartz - of the same size, and recovery of these phosphate grains as a commercial product is not possible by simple washing methods. Phosphate recoveries approaching complete extraction can only be effecte by applying metallurgical processes, either mechanical or chemical. As yet, most of these processes have not advanced much beyond the laboratory or perhaps the pilot-plant stage. Such processes may have some application to the beneficiation of phosphatic ores or washer rejects, but a discussion of them is not within the scope of this paper."

Apr 1, 1929

To help mine safety and health professionals manage and reduce hazardous noise exposure with a software tool that simplifies the record-keeping and analysis process. Background Hearing loss resulting from overexposure to noise continues to be a problem throughout the U.S. mining industry. Studies indicate that 70%?90% of all miners have a noise-induced hearing loss severe enough to be classified as a hearing disability by the time they reach retirement age. To address this problem, the National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software program. DOSES is designed specifically for use by mine management and safety personnel to simplify the record-keeping and analysis associated with time-motion studies, making it easier to identify and solve noise exposure problems.

Jul 1, 2009

By E. P. Youngman

Although, an effort has been made to standardize and codify the mining law to apply to the entire German Nation, nothing has yet been accomplished. abstract, which applies only to Prussia, the largest and most important of the German States, is based upon the Prussian Mining Law (Preussisches Berggesetz) of June 24, 1865, which grants to certain provinces, communities, and districts special exceptions, of no particular significance, except locally.

May 1, 1930

By E. P. Youngman

The mining law of the Belgian Congo does not cover the Province of Katanga nor the District of Kivu (in Eastern Province). Regulations of the Comité Spécial du K tanga are in force in Katanga and those of the Comité National du Kivu in Kivu. The three laws differ only in detail, and grants made by the Comité Spécial du Katanga or by the Comité National du Kivu must be approved by the Ministry of Colonies. The following résumé is designed to coordinate the three sets of regulations.

May 1, 1930

By Jeanne A. Zimmer, Charles D. Taylor, Edward D. Thimons

Strategies for monitoring methane levels during roof bolting in an extended cut entry were evaluated. Testing was conducted at the Pittsburgh Research Laboratory’s methane test gallery. Operating conditions were varied and methane releases at the face and drill holes were simulated. Methane readings were taken at the face, and at locations outby the face. Results show that, when the major source of methane was at the drill holes, the highest methane readings were at locations on or 6.1 m (20ft) inby the bolting machine. Methods for selecting better outby sampling locations, when the majority of the methane is released at the face, are examined. During roof bolting it is easier to sample at these outby locations rather than at the face. Further testing is needed to determine what relationship exists between methane concentrations at the outby locations and at the source of the methane release.

By George T. Faust

The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the various types of clays to be found in the Southern States. In connection ,with this work, the petrographic laboratory is called

Jan 1, 1940

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By J. E. Chilton, C. R. Carpenter

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro- chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1- to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light- emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 1992

By Thomas M. Barczak

The success of longwall mining can largely be traced to the development of powered roof support systems. The most significant improvement in powered support design has been the shield support, which improved kinematic stability and promoted the application of longwall mining in difficult-to- control caving conditions where chock and frame supports were inadequate. The most obvious trend in shield design has been an increase in shield size and capacity. This U.S. Bureau of Mines report examines shield design and operation practices and their consequences for the utilization of high-capacity shield support systems. An optimization goal is to minimize support loading by selecting an active shield setting force that is compatible with strata behavior and shield loading characteristics. Shield stiffness is an important design parameter that is often overlooked. A consequence of increasing shield capacity by incorporating larger diameter leg cylinders is a proportional increase in shield stiffness. Setting forces have also increased in direct proportion to the increase in shield capacity. The increased stiffness and higher setting force cause the available capacity to be consumed more quickly, severely limiting the ability of high-capacity supports to last longer and provide reserve capacity for difficult mining conditions.

Jan 1, 1992

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 829) to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1987

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By J. R. Wait, D. A. Hill

The feasibility of locating a buried vertical magnetic dipole source (horizontal loop) from surface measurements of the vertical and horizontal magnetic field components has been investigated by Wait (1971). , For sufficiently low frequencies, the magnetic fields have a simple static-like behavior, and a single observation of the ratio and relative phases of the vertical and horizontal field components is sufficient for location when the earth is homogeneous. However, when inhomogenieties are present, the surface fields will be modified, and source location may be more difficult. In order to obtain a quantitative idea of the surface field modifications, we consider a spherical conducting zone as a perturbation to the homo- geneous half-space. A rigorous solution for the buried sphere problem has been formulated by D'Yakanov (1959). Unfortunately, his solution is restricted to azimuthally symmetric excitation, and even then the solution is not in a convenient computational form. However, if the sphere is electrically small and is located at a sufficient distance from both the dipole source and the interface, the scattered fields can be identified as the secondary fields of induced dipole moments. The latter are equal to the product of the incident fields and the polarizabilities of the sphere. The details of the approach are given by Hill and Wait (1973). Wait (1968) has used this induced dipole moment approach for scattering by a small sphere above a conducting half-space. The method has the advantage that it is easily generalized to scatterers of other shapes for which both the electric and magnetic polarizabilities are known, such as spheroids (Van de Hulst, 1957). This concept has

Jan 1, 1973

By M. J. Friedel, D. E. Scott, T. J. Williams

Rock masses in deep level mines are subject to high stresses, which can result in unexpected failure of rock into mined-out openings. Historically, various independent methods have been used to discern the causes of rock bursts and to evaluate stress conditions in rock masses susceptible to violent failure. Personnel from two research centers of the former U.S. Bureau of Mines, Spokane and Twin Cities, investigated a rock burst that occurred in May of 1994 in a rock mass between the 4400 and the 4600 levels of the Sunshine Mine, Kellogg, ID. The team evaluated the current state of stress in the pillar and the most likely cause of the rock burst by studying the seismic history of the pillar, examining the geology, analyzing the available in situ stress data, calculating possible fault-plane solutions for the burst, and performing a seismic velocity tomographic survey. The results of the study showed that post-rock-burst seismicity was concentrated about 15 to 30 m west of and about 15 m above the rock-burst location. The pillar is composed of a very hard sericitic-to- vitreous quartzite of a type rarely found in the mine, but that is often found in other district mines having a history of seismic activity. In situ stress analysis of the pillar and the surrounding rock mass showed a probable stress rotation from northwest-southeast to east-west. Of four fault plane solutions, the most probable was either a left-lateral, strike-slip movement with a compressive principal stress oriented nearly north-south, or a right-lateral, strike-slip movement oriented east-west. Finally, tomographic images showed low-velocity areas (interpreted as areas of low stress) associated with the crosscuts and haulageways, and high-velocity areas (interpreted as areas of high stress) associated with the rock-burst location. High velocities were also found in a planar area oriented in an elongate northeast-southwest direction.

Design a new acoustic monitoring system to more accurately forecast impending rock bursts, and to assist in understanding the rock burst phenomenon. Background Rock bursts arc the major cause of injuries and deaths in deep underground mines in the Silver District near Wallace, ID. Bureau investigations of the rock burst phenomenon resulted in significant improvements in computerized acoustic technology, and achieved limited success in forecasting several large events. Research demonstrated that the location of rock noise, and the rate at which these events occur, are indicators of areas that could fail violently. In minewide monitoring, the typical array of acoustic sensors (geophones) is arranged to cover an entire mine with 16 to 32 separate instruments. The mines intended to be covered may be 7,000 feet in depth and up to several miles in extent. While such an arrangement is capable of detecting and locating large seismic events (rock slippage along natural fractures or faults), the geophones are too far apart to accurately locate mining-induced events at the active workplaces. The Bureau devised a strategy to concentrate the geophones into typical slopes (mining areas about 200 by 500 feet) to record the rock noise in areas where the miners work. By using such a dense geophone array at a mine, the Bureau provided event location and rate information to mine operators who removed workers and ceased production from active mine areas that subsequently suffered rock bursts.

Jan 1, 1989

Develop a method for control of groundwater inflow to chronically "wet" sections of underground coal mines, in order to reduce groundwater interference with mining activity and to minimize acid mine drainage. Approach In eastern coal regions, groundwater stored in fracture zones in the rock mass can create a significant water problem for underground mining operations. Fracture stored inflow to mine workings impedes mine productivity since storage water sources usually release at the active face, creating the poor mining conditions typical of a "wet" section. Fracture water can also contribute to AMD problems when the water subsequently contacts sulfide minerals in the coal, The Bureau of Mines has developed a mine-dewatering method that eliminates many of the problems associated with mine water inflow by draining these fracture zones before the water can reach the developing face and interfere with mining activity. How it Works The dewatering method removes large volumes of the stored groundwater through high-capacity pumping from a minimal number of wells placed strategically on fracture traces (the surface expressions of fractured rock zones). These fracture traces are located through low-level aerial photographic and geologic investigation. As shown on the map, dewatering wells are sited precisely on fracture trace intersections in order to take advantage of the increased pumping capacity gained from these zones of high permeability. Once well drawdown indicates that the stored water is depleted,

Jan 1, 1983

Provide the mining industry with a wireless surveying system for increasing efficiency in the drilling of methane drainage or exploration boreholes. Approach The Bureau of Mines has pioneered the technique of methane control by drilling long, horizontal drainage holes from within the mine complex. It was recognized during the early drainage projects that a major portion of the drilling operation was dedicated to hole surveying. In some cases more time was actually being spent on the surveying operation than on drilling. The large amount of time required for hole surveying was the result of having to pump an instrument to the bottom of the hole, then retrieve it with an attached wire line. Naturally as hole depth increased, so did the amount of time needed to perform the survey operation. If the survey operation could be improved it was obvious that overall efficiency in drilling of long, horizontal methane drainage holes would be greatly increased. The Bureau of Mines, therefore, developed, fabricated and tested in an operating coal mine a permissible wireless survey system specifically designed for small diameter methane drainage drilling. The prototype survey system was completed in 1982 and was given the IR-100 Award by Industrial Research and Development Magazine. A second generation survey system is currently being constructed using updated state-of-the-art electronic technology. The second generation system will be more portable, more reliable, easier to maintain, and less costly.

Jan 1, 1984