Search Documents

GLOSSARY Acid- and toxic-forming materials. Rock or coal layers containing significant amounts of pyrite or other minerals which, if exposed by coal mining, will cause acid or toxic drainage to occur when acted upon by air and water. Add mine drainage. Any water with a pH less s than 6.0 draining from a coal mine. Water is often orange-colored because of the presence of oxidized iron. Adit. An underground mine entry at sites where coal seams are exposed at ground level. Apple core. A complete hilltop (360°) left exposed by not backfilling the highwall. Approximate original contour. The surface configuration achieved by backfilling and grading the mined area so that be reclaimed land closely resembles the general pre-mining surface configuration and blends into and complements the drainage pattern of the surrounding terrain. Area mining. A surface mining method that is carried on in level to gently rolling topography on relatively large tracts of land. Active area mine pits may be several miles long. Arid and semiarid regions. Lands, generally west t of We 100% meridian, where water use by native vegetation equals or exceeds that supplied by natural precipitation, and rainfall is insufficient to support agriculture. Annual precipitation is normally 20 inches or less. Auger mining. A mining technique often used by surface mine operators when the overburden becomes too for the coal to be mined economically using traditional surface mining methods. Large-diameter (usually 2'-4') horizontal holes are drilled as much as 300 feet into We vertical Me of the coal bed by an auger. Like a bit used for boring holes in wood, coal augers consist of a cutting head with a screw-like extension. As the auger turns, the head breaks up the coal and the screw carries it back into a conveyor that loads it directly into a truck. Backfilling. The operation of refilling an excavation using material removed during the mining process. Bench. The level or flat working area at the base of the highwall that is excavated between the exposed coal seam and the original surface of the ground. Bucket wheel excavator. A continuous-digging machine that uses a rotating vertical wheel with buckets for large-scale stripping and excavating. Cessation Order. Order to cease mining issued to a coal operator by the regulatory authority due to severity of violations, Contemporaneous reclamation. Restoration of mined land that occurs as soon as practical after coal removal. Contour mining. A mining method commonly used in eastern mountainous topography where coal is removed in a narrow strip around the hillside. The extent of the cut into the hillside is determined by the depth of overburden at the highwall compared with the thickness of the coal seam. Daylighting. A term used to describe a surface mining procedure that exposes abandoned underground coal mine workings to enable removal of the remaining coal. Daylighting is followed by land reclamation. Dragline. An excavating machine, usually used in large, flat areas, that drags a bucket (which holds up to 220 cubic yards of material) toward the machine by cables, loads it with spoil, and then hoists it wit a boom up to 350 feet long, allowing the machine to excavate wide benches by depositing the spoil hundreds of feet away from the highwall. Grading. The process of smoothing the disturbed areas of the mine site, after the coal is removed, to closely approximate the pre¬mining terrain. Haul road. Any road constructed, improved, maintained, or used by mine operators and located within the permit area. Head-of-hollow fill. See "valley rill." Highwall. The cliff-like excavated face of exposed overburden and coal in a surface mine. Hydroseeding. Planting of seed mixed in a water medium. Water, mulch, lime, fertilizer, and seed are blended and sprayed onto regarded soil.

Jan 1, 1992

By Joseph A. Holmes

The perpetuation of the supply of anthracite coal in Pennsylvania is a national as well as a State problem. Any investigation that shows how larger percentages of this coal may be saved in mining, without excessive cost, and without dangerous subsidence of the overlying surface ground, has a national as well as a local interest. Messrs. Conner and Griffith, who conducted the investigations described in this report largely for the city of Scranton, are consulting engineers for the Bureau of Mines for investigations similar to those they have already made in connection with their Scranton work; and this report is published by the bureau in response to numerous requests, because of the fact that the information it contains will prove useful in the general solution of similar problems in many of the country's coal fields. A study of the accompanying maps will show that the city of Scranton is underlain by 11 separate beds of coal, varying in thick- ness from 2 to 24 feet. It is estimated that before mining opera- tions were begun these beds of coal contained underneath the present city limits of Scranton 600,000,000 tons of coal. The 27 collieries operating within the city limits, working independently of each other, had excavated and removed, up to March, 1911, an aggregate of 198,000,000 cubic yards of coal and accompanying rock, or 3,000,000 cubic yards more than the total amount of material excavated and to be excavated by the United States in constructing the Panama Canal. This fact illustrates something of the magnitude of the problem that the city of Scranton, with the aid of these engineers and of a special commission or advisory board, has undertaken to solve. The excavation has included 177,000,000 tons of coal and 44,000,000 tons of rock and accompanying refuse. This leaves about 420,000,000 tons of coal still to be removed. As a result of other investigations and of experience in adjacent anthracite mines, Messrs. Conner and Griffith and the advisory board of engineers have advised that, as far as may be necessary to prevent dangerous surface subsidence, the spaces remaining beneath the city of Scranton from the excavation of the above-described material should be filled with sand and other materials by flushing or other processes. This operation is expensive, but it is believed to be not beyond the reach of what is practicable, nor in excess of the value of the coal that may be removed and the amount of damages that may result from the caving in of the surface if such a plan is not carried out. No one realizes so fully as do the authors of this report the need of additional tests and other investigations before the data now pre- sented by them can be fully accepted as sufficient for all purposes in the solution of the problem; and it is expected that at some early date a more extensive series of similar tests can be made by the Bureau of Mines under the supervision of Messrs. Conner and Griffith on a larger scale and under a greater variety of conditions. The field examinations made for the Bureau of Mines by N. H. Darton, which are described briefly in a chapter of this bulletin and will be discussed at length in a bulletin to be published later, indicate the extent and distribution of the sands, gravels, and other materials in the Scranton-Wilkes-Barre district available for flushing purposes if further tests indicate their relative merits; and it is expected that the relative merits of these different materials will soon be tested under such conditions as will furnish the desired information.

Jan 1, 1912

By F. C. Turin, K. M. Cornelius

1. INTRODUCTION Underground mining in the USA has undergone significant change in the past 20 years. Two key elements have been increased mechanization and a more educated work force in spite of these changes, many jobs continue to be labor-intensive and repetitive in nature. They entail tasks that, performed over time, can take a toll on the soft tissues and joints. The problem may be compounded by an aging mining workforce. In 1996 the mean age of the coal mining work force was 45 years and the median total years of experience was 20 (NMA 1998). As a person ages, the body resilience to chronic wear and. tear is reduced, which may cause a worker to pay an increasingly higher health price for performing the same task. Mining companies, like many others, are becoming more aware of cumulative effects to the worker as reports of these types of injuries rise. . Conducting a job analysis is an important step when considering a job redesign or modification to reduce worker cumulative trauma exposure. A basic approach to job analysis is to examine the types of aches and pains reported, the tasks performed, and work site conditions. The US Bureau of Mines (USBM) conducted an evaluation of roof-bolting tasks performed at an underground coal mine concerned about early warning signs of cumulative trauma. This evaluation will comprise the primary focus of this chapter. The approach used for the roof-bolting race study may be applicable to other work environments. 2. FUNDAMENTALS OF CUMULATIVE TRAUMA EXPOSURE Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders that affect the nerves, tendons and muscles. Common examples include lower back pain, tendinitis and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may not appear immediately, but can take weeks, months or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute there to a single event. In fact, it is more common to identify factors that may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTD) have been commonly used to refer to disorders that have occurred due to work-related activities. Three main risk factors contribute to CTD: force, repetition and awkward postures. Any one or combination of these may contribute to the development of CTD. Therefore, the design of equipment in conjunction with the required tasks should be evaluated when attempting to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list (Putz-Anderson 1988), describes ergonomics concerns that, overall, should be minimized at the work area: • Crowding or cramping the worker: a work area layout may unnecessarily constrain movements of the worker. • Twisting or turning: placement of tools and materials may require the worker to twist the spine to fulfill the requirements of the job. • Repeated reaching motions: the layout of the work area may require the worker to lean to reach and grasp the necessary tools and controls. • Misalignment of body parts: the arrangement of the work area may require the worker to frequently have one shoulder higher than the other or have the neck or spine bent to one side. While many of these concerns are a function of equipment design and environmental conditions, making workers aware of these issues may help them to adapt their work habits to reduce risk of injury. Additionally, this information is useful when conducting an ergonomic evaluation of a work area and associated tasks. 3. UNDERGROUND MINING ENVIRONMENT The underground mining environment is a unique challenge. It is more difficult to develop controls for an underground mine site as compared with a factory setting where equipment and facilities can be more easily designed to reduce worker force, posture and repetitive exposures. In an underground mine, workers are required to perform labor-intensive tasks that often cannot be avoided due to environment constraints. The dynamic nature of the environment does not allow easy implementation of mechanical assists to reduce force exposure. Many of the tasks performed by workers are repetitive. Restrictive work areas due to low ceiling height, low lighting levels and large pieces of equipment cause workers to perform these tasks in postures that are not desirable. Designers of underground mining equipment can control how a machine will function, but not the environment in which it will be used, Hazards in an underground mine cannot be completely removed by redesigning the system. There are many hazards and information sources that must be continually monitored by workers including their position in relation to large pieces of mobile equipment and unpredictable geological anomalies. Thus, immediate dangers may take priority over awareness of ergonomic considerations while performing a job. 4. CASE STUDY OF UNDERGROUND ROOF BOLTING 4.1. Roof Bolting and Cumulative Trauma Exposure In an underground coalmine, after an area is mined it is necessary to support the roof to keep it from collapsing. Since 1950, the primary method for supporting the mine roof has been installation of roof bolts. Long bolts installed into the roof compress the layers of strata achieving a uniformly distributed support anchorage. Roof bolts, typically 6-8 feet long, are installed by workers using large roof-bolting machines. There are different types of machines

By R. D. Currie

The practicability and dependability of two permissible methane-indicat- in detectors recently developed were proved conclusively by extensive tests in the return airways of all mines operating in the anthracite region in most of which samples and readings were taken with one or the other of the two in- dicating detectors. These detectors roved dependable and accurate within practical limits, and their general use should be encouraged as an aid to bet ter ventilation, more accurate control of air currents, and greater safety in mines.

Feb 1, 1936

By J. R. Thoenen

This circular is part IV of the third paper (entitled "Sand and Gravel Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part I discussed the use of power shovels, draglines, and excavator cranes; part II discussed the use of power scrapers, slackline cableway excavators and hydraulic monitors; and part III discussed the use of hydraulic, clamshell, ladder, and dipper dredges. This circular discusses haulage equipment in general, particularly the use of industrial cars with locomotives or hoists as the motive power. Part V, to follow, will discuss the use of other types of haulage equipment.

Oct 1, 1935

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By B. F. Naylor

"INTRODUCTION Investigation of the physical properties of electrolytic manganese and its alloys has constituted a part of the program of the Bureau of Mines for several years, and already extensive data have been reported. 3-14/ Heat-content measurements above 25° C. of pure manganese 15/ were completed recently at the Pacific Experiment Station of the Bureau, and the results obtained removed many of the inconsistencies in previously reported data. This paper reports heat-content data of seven manganese-copper alloys, varying in composition from 25 to 90 percent man-ganese. The alloys, obtained from the Salt Lake City Station, 16/ had been quenched from 850° C, and cold-worked. Without further heat treatment, heat-content measurements of each of these alloys were made at 100° or less temperature intervals from 450° to 850º C., as it was considered likely that any abnormal behavior of the specific heat would be found in this temperature range. Also, a portion of each alloy was heat-aged at given temperatures for periods of time thought sufficient to reach phase-equilibrium; then the heat-contents above 25° C. were determined at the aging temperatures. (Heat-aging was done at approximately 450°, 550°, 650°, 750°, and 850° C.)METHOD AND MATERIALSThe heat contents were determined by the ""drop"" method in a previously described apparatus. 17/ The calorimeter was cali-brated with electrical energy, measured in international joules, and the results were converted to the conventional thermochemical calorie by the relation, 1 cal. = 4.1833 int. joules."

Jan 1, 1946

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By Robert L. Lagace

This final report documents the work done by Arthur D. Little, Inc. (ADL) on behalf of the U.S. Bureau of Mines, Pittsburgh Mining and Safety Research Center (PMSRC) , on Contract H0122026 (which began in August of 1971) . Under this contract ADL provided technical assistance to the Bureau on a task basis on virtually all aspects of the Bureau's programs related to present and planned emergency and operational communications and miner location systems for underground coal mines. The work consisted of in- dependent investigations, analyses, experiments, breadboard and prototype hardware development, workshops and technology transfer seminars on mine communications, and on-going evaluations and guidance related to the Bureau's contracted programs on electromagnetic noise, mine communications systems, and trapped miner location. This final report documents the work in two volumes, Volume I, "Emergency and Operational Mine Communications," and Volume II, "seismic Detection and, Location of Isolated Miners." The Tables of Contents of both Volumes are included in each Volume.

Jan 1, 1974

By John B. Goodman

This report presents a study of a modification of the precision laboratory carbonization-assay apparatus that renders the unit capable of performance at low-, medium-, and high-temperature assay levels and permits, under controlled conditions, evaluation of the relationship between carbonization temperature and the yield of pyrolysis products. Second, the interest and value derived from the temperature study data directly apply to the particular semiplant carbonization processes and techniques currently being investigated in this laboratory. Data obtained with the assay apparatus enables the fuel technologist to predict the probable yields of carbonization products from pilot-plant operations under various carbonizing conditions. Data obtained with the assay apparatus has been used to predict the product yields of industrial carbonization plants at Kemmerer, Wyo., and Rockdale, Tex. The assay provides a useful tool in detecting, from the carbonized plant product, the degree of effectiveness of pilot-plant operation. Third, the residual volatile matter in some industrial carbons has broad significance. Evaluation of the volatile material remaining with or in the carbon may be assessed through the high-temperature-assay technique. The low-temperature carbonization assay devised by the writers has proved to be a versatile tool in predicting the probable product yields from pilot-scale carbonization processes. The apparatus described in previous publications has been modified to extend the range of testing above 500° C. without impairing the accuracy and reproducibility obtained in the low-temperature range. Results presented here include product yields from a typical Texas lignite and Wyoming subbituminous-B-rank coal over the temperature range 150° to 1,000° C.

Jan 1, 1958

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

Great strides have been made in recent years to reduce the disaster potential of underground mine fires. However, mines can still be caught unprepared for a fire emergency. Fires can grow too large before they are detected, warning systems can be too slow and uncertain to reliably signal the danger, and suppression systems can be inadequate to extinguish the flames. New mining systems and equipment may create unanticipated fire hazards, and new materials may generate highly toxic combustion products. This report contains papers that summarize recent significant developments from the Bureau of Mines mine fire protection research program relating to these problems. Certain of these findings are also applicable to surface mining operations. The papers fall into the general categories of fire detection and instrumentation, fire warning, fire suppression, diesel equipment, spontaneous combustion, and toxicity analysis of combustion products.

Jan 1, 1988

By G. A. Burrell, G. W. Jones

As a part of the work which the Bureau of Mines carried out in 1916 and 1917 pertaining to the compressibility of natural gas , it became necessary to de termine the pressure -volume relations of several of the paraffin hydrocarbons of which natural gas is composed . Results of the work on natural gas were published in Technical papers 131 (Burrell , G.A. , and Robertson , I.W. , The compressibility of natural gas to high pressure , Bureau of Mines Tech . Paper 131 , 1916 , 12 pp. ) and 158 (Burrell , G.A. , and Robertson , I.W. , Compressibility of natural gas and its constituents with analyses of natural gas from 31 cities in the United States , Bureau of Mines Tech . Paper 158 , 1917 , 12 pp . ) , and curves were given of pressure volume deviations of the gases , methane , ethane , propane , and carbon dioxide at high pressures . original experimental data on these gases , however , were not published . The In view of many inquiries which the Bureau has received with reference to the original data on the se gases , and the importance of the pressure -volume relations from which it is possible to calculate the deviation of any natural gas who se composition is known , the original data as determined by Burrell and Robertson are pre sented below .

Aug 1, 1921

By N. E. Hanna

To be authorized for use in coal mines, explosives and blasting devices must pass certain safety tests prescribed in schedule 1F,3/ on the basis of extensive practical and theoretical research by the Explosives Testing Station of the Federal Bureau of Mines. An explosive or blasting device that passes these tests is placed on the active permissible list. As this list is constantly revised, it has been the practice of the Bureau of Mines periodically to publish the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. This circular covers all permissibles including additions, transfers, and changes made between December 31, 1945,4/ and December 31, 1951.

Jan 1, 1952

By Thaddeus B. Evans

This information circular is one of a series describing mining methods and costs, being published by the Bureau of Mines. The Sunbright mine of the Foote Mineral Co. at Sunbright, Va., is the southernmost underground limestone mine in the State. It is a comparatively recent operation, and a description of its rapid development to production stage may have particular interest for the limestone-mining industry. ACKNOWLEDGMENTS Acknowledgment is made to the executives of the Foote Mineral Company including F. B. Shay, vice president in charge of production, W. B. Towner, general production manager; and to the members of the company staff at Sunbright for their assistance in preparing this paper.

Jan 1, 1957

By R. F. Tenney

No detailed information has been published heretofore on the performance of small industrial-type anthracite stokers in building-heating service, apparently because of the difficulty of comparing the performance of one unit with that of another over an entire season's operation. Studies of competitive heating fuels have been similarly handicapped, and attempts to compare fuels are seldom technically sound in this investigation, the performance of a 60-in. Losch4 stoker burning rice-size anthracite in a standard commercial boiler was observed during a 4-month winter-spring season. It was used to heat two buildings at the Bureau of Mines' Anthracite Research Center at Schuylkill Haven, Pa., with the customary type of automatic pressure-range control. Attendance was limited to inspecting, fuel weighing, data recording, and ash removal. Results were computed daily and grouped by weekly periods to minimize daily irregularities. The same stoker-boiler unit had already been tested in a series of American Society of Mechanical Engineers (ASME) test code runs, with the stoker running continuously and with other conditions well stabilized A comparison of results from the code test and the building-heating tests provided information not available in the past for a single stoker unit, assisted in analyzing heat losses not computable in a cyclic operation, and established a basis for evaluating stoker performance in heating service.

Jan 1, 1963

By J. R. Nettle

The electrodeposition characteristics of seven binary alloys of titanium have been investigated. The object of the electrorefining experiments with an alloy was to determine the efficiency of titanium separation from individual alloying elements under established conditions. Reported results are only indicative. It is conceivable that numerous duplications of tests might give average maximums that would vary from those noted in this report; however, in the few tests that were repeated, the magnitude of transfer of the alloying elements was of the same order. The results detailed herein are for a given set of conditions. Many combinations of operating variables are possible, and the results achieved under different conditions probably would differ from those reported.

Jan 1, 1958

By W. Bruce Montgomery

Manganese oxides occur, with some iron oxides, in small scattered lenses on property controlled by the Columbia Manganese Co. (1943) near Evington, Campbell County, Va. The company mined some manganese ore during 1917 and 1918. A preliminary examination in May 1942 indicated the possibility of finding additional ore. On August 21, 1942, the Bureau of Mines began prospecting to verify the continuity of the ore exposures. Work on this project continued until February 5, 1943. Prospecting and development work included shaft sinking, crosscutting, drifting, trenching, and test-pitting in six separate areas indicating two types of deposits. The most predominant type is a wide brecciated area in which occur lenses or pockets of nodular manganese oxides. The other type is characterized by more of a vein structure, including thin layers of manganese oxides.

Jan 1, 1949

By C. E. Augustine, P. Nicholls

"INTRODUCTION A layer of soot on the heating surface of a boiler decreases efficiency because it increases resistance to the flow of heat, with the result that the heat transfer to the water is lower and the temperature of the flue higher than they would be if the surface remained clean. The percentage of reduction in heat transfer depends on the position and area of the sooted. The percentage of reduction in heat transfer depends on the position and area of the sooted surfaces, the thickness of the most, until the percentage of the total heat absorbed by those surfaces when clean; thus it will vary with the type of boiler and in particular with the ratio of the area of the convection heating surface to the total area. Medium-size and large boilers usually are equipped with soot blowers, and tests have been published giving the increase in efficiency resulting from removal of the soot. Fuel savings up to,8 percent have been reported, but 4 to 5 percent is probably more conservatives. However, these savings may not be due wholly to a reduction the thermal resistance of the surfaces but may be due partly to improvement in the combustion because of better draft or more uniform flow of the gases. In addition, the deposits on the surface of boilers include as a clinker, and as the size of the boiler and the rate of burning increase very little or none will be soot.There are no corresponding test data on small boilers operated at low rates of burning. In stall boilers, deposits are much thicker, and it might be expected that the reduction in efficiency would be greater; in fact, statements have appeared suggesting that the decrease may be as high as 50 percent. This investigation was undertaken because the Bureau frequently receives requests for authoritative information on the effect of soot in small and other heating boilers."

Feb 1, 1935

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative face positions are tabulated for 110 subsidence monuments. Measurements were taken twelve times during the eight months it took to mine the panel. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981