Search Documents

By Gary W. Kramer

The Bureau of Mines has developed a rapid analytical method for the determination of anions by ion chromatography (IC) in phosphate rock mining materials and cement kiln dust (CKD). The procedure employs an Na2C03 fusion of the sample, followed by a water extraction that allows direct injection of the sample into an ion chromatograph without separator column poisoning by the transition metal ions. Fluoride (F-) and phosphate (P043-) were determined in 24 phosphate rock processing and waste material samples by the IC method. The results were compared with a pyrohydrolytic distillation-titration method for F-and a colorimetric procedure for P043-. Excellent analytical agreement was obtained for F-and p043-values determined by IC and the comparable wet chemical methods. Fluoride values ranged from 0.3 wt-pct in the filter cake to 3.6 wt-pct in phosphate rock concentrate. Phosphate values ranged from 1.2 wt-pct in the filter cake to 33.8 wt-pct in the rock concentrate. Fluoride, chloride, phosphate, nitrate, and sulfate in several CKD samples were determined by the IC method and standard wet chemical techniques. Excellent agreement was obtained between the two methods for all anions. A total of 113 CKD samples from all areas of the United States was analyzed by the IC method. Fluoride values ranged from <0.01 to 0.36 wt-pct. Chloride values ranged from <0.01 to 12.5 wt-pct. Sulfate values ranged from 0.41 to 31.6 wt-pct. Phosphate and nitrate were detected in only about 25 pct of the samples at >0.02 wt-pct. Maximum phosphate and nitrate values were 1.0 and 1.6 wt-pct, respectively.

Jan 1, 1982

The question of earth models has repeatedly arisen in our work. An accurate representation of the seismic properties is required for three reasons: 1.To be able to determine from a set of received arrival times, the location of a seismic source in the earth, and secondly the degree of accuracy required in the model used for calculating source location from the set of arrival time differences. 2. To be able to determine the expected arrival times at an array of geophones produced in response to a hypothetical source in the earth. 3. To be able to estimate received signal strengths more accurately. The work reported here on earth models is based on information from sever- al consultants and from others who expressed an interest in the problem and supplied information to us. II. COAL MINE GEOLOGY On one of our earlier assignments for the Bureau of Mines, Earth Science Research Inc. of Cambridge, Massachusetts prepared for us a short description of the lithology to be expected at coal mine sites. This description follows, together with the ranges of compressional seismic velocities (Figure I*) associated with typical materials comprising the layered structure of a coal mine area. Coal is primarily associated with fresh water sediments including sandstones, shales, and clays, and occasionally may be metamorphased to varying degrees. In the Appalachian Basin the coal beds occur within cyclical sequences of non-marine shales, sands tones, conglomerates, limes tones, and clays. The beds range in thickness from a few inches to 60 feet, averaging between 2 feet and 10 feet. They have generally broad areal extent, occasionally up to 5,000 square miles, and have an overall tabular or lens-like shape. Within a particular lens, local changes in thickness are normal.

Jan 1, 1974

By Bruce K. Cantrell, Winthrop F. Watts

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989(1), which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This report reviews, available diesel exhaust aerosol and gas measurement techniques. Measurement of human exposure to toxic agents is the first step in determining the exposure-dose-response relationship. It is a fundamental step in risk assessment. Measuring exposure to diesel exhaust pollutants is particularly challenging due to the complexity and variability of exhaust components. This paper reviews current occupational health standards for diesel emissions and available diesel exhaust gas and aerosol measurement techniques. Although surveys in mines have primarily assessed diesel exhaust exposure using diesel particulate matter (DPM) some exhaust gas measurements have been used as indicators of exposure. DPM is emphasized because it is a major component of diesel exhaust, is suspected to make a major contribution to the health hazard, and is measurable. OCCUPATIONAL HEALTH STANDARDS Occupational exposure surveys of diesel exhaust frequently measure regulated pollutants, or pollutants that are suspected carcinogens, even if no permissible exposure limits (PELs) have been established. In the United States, various organizations recommend a range of allowable values for diesel exhaust gaseous constituents, including carbon monoxide (CO), carbon dioxide (CO2), sulfur dioxide (SO.), nitrogen dioxide (NO2), nitric oxide (NO), and formaldehyde (HCHO). Table I summarizes these recommended levels, showing 8-hour or 10-hour time-weighted-average values where available; where these are not available, 15-minute short-term [ ]

By R. V. Ramani, A. S. C. Owili-eger

The Federal Coal Mine Health and Safety Act of 1969 (sec. 303 (b)) stipulates that no working section of the mine shall contain more than 0.5 percent carbon dioxide and no harmful quantities of other noxious or poisonous gases such as the oxides of nitrogen. The concentration of methane should at all times be maintained below one percent. A split of air returning from any working section shall contain no more than 1.5 percent of methane (sec. 303 (i) (2)) and air that has passed by an opening of any abandoned area shall not be used to ventilate any working place in the coal mine if such air contains more than 0.25 percent of methane (sec. 303 (j)). Methane concentration in the returns from the bleeder entries should not exceed 2.0 percent (sec. 303 (i) (3)), and no air that has passed through an opening which is inaccessible for examination shall be used to ventilate any active areas. While the air quantity requirements alone can easily be met, the governing condition in most mines is the dilution requirements for quality control. A sufficient quantity of air is required to render harmless and carry away noxious and respirable pollutants. In recent years, changes in coal extraction methods, rates of advance, location of available reserves, position of prominent methane sources and horizons, and geological sequences have contributed sig¬nificantly to alterations in rates, patterns and character of numerous methane emissions. Gas production of 10 to 15 million standard cubic feet per day is not uncommon from deep mines (Cervik, 1969). Thus, because of the large capital outlay involved in the instal¬lation and subsequent remedial actions of methane drainage systems, knowledge of gaseous flow patterns and storage characteristics of the

Jan 1, 1974

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

By J. E. Chilton, Jr. Dubaniewicz

Many mines rely on toxic gas sensors to help maintain a safe and healthy work environment. This report describes a prototype monitoring system developed by the U.S. Bureau of Mines (USBM) that uses light to power and communicate with several remote toxic gas sensors. The design is based on state-of-the-art optical-to-electrical power converters, solid-state diode lasers, and fiber optics. This design overcomes several problems associated with conventional wire-based systems by providing complete electrical isolation between the remote sensors and the central monitor. The prototype performed well during a 2-week field trial in the USBM Pittsburgh Research Center Safety Research Coal Mine.

Jan 1, 1995

By Alton B. Cook

Data are presented to show oil vaporization resulting from the passage of natural gas through a sand-packed tube saturated with synthetic reservoir oils. The Bureau of Mines performed 13 experiments, using reservoir oils synthesized with base crude oils of approximately 22°, 35°, and 45° API, at 100°, 175°, or 250° F and 1,100, 2,600, or 4,100 psia. It has been determined that the amount of vaporization is significant if proper conditions exist. These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil, and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized.

Jan 1, 1969

By J. C. Franklin

An experiment was conducted by the U.S. Bureau of Mines and the Canada Centre for Mineral and Energy Technology (CANMET) to measure the emanation rate of radon from cemented unclassified mill tailings in two dewatered stopes of a uranium mine at Elliot Lake, Ontario, Canada. The radon was monitored upstream and downstream and in both stopes to determine the concentration in the stopes and the amount exhausted from both stopes. The emanation rate was determined to be 0.55 pCi/cm2 sec-1 from the mill tailings, which is approximately 1,000 times higher than the average flux in the mine before backfilling.

Jan 1, 1982

By E. Aamland

Preparation of high-purity magnesium-yttrium alloys by electroreduction of Y2O3 dissolved in a YF3-LiF bath and the subsequent deposition of yttrium in a molten magnesium cathode was investigated in laboratory-scale apparatus. Parameters such as temperature, current density, and electrolyte density were studied. Electrolysis was conducted in a specially designed MgO diaphragm cell at temperatures ranging from 780° to 970° C. Alloys containing up to 55 weight-percent yttrium were prepared at cathode current efficiencies of 21 to 60 percent. Cell design and operation are described, and some of the limiting conditions pertaining to the method are discussed.

Jan 1, 1973

By P. G. Pigott

This investigation by the Bureau of Mines demonstrated that building bricks can be produced by the steam-curing process from various types of industrial mineral wastes. Wastes, utilized to produce bricks, consisted of copper mill tailings, roofing granule fines, asbestos fines, and zinc mill tailings. Bonding of the wastes with either Ca(OH)2 or portland cement resulted in building bricks that met ASTM specification C73-67 for grade SW and MW bricks when evaluated in accordance with ASTM designation C67-66 on sampling and testing of brick. An economic evaluation of the process indicates the total operating cost per 1,000 bricks is about $36.

Jan 1, 1974

By Judith A. Eisele

The possibility of improving the volatilization of gold through the formation of a metal-gold chloride vapor complex was investigated. Gold-silica mixtures, containing ferrous and nonferrous minerals and salts as additives, were treated in a laboratory tube furnace with a flow of chlorine gas at various temperatures. The addition of pyrite (FeS2) to a charge of gold-silica increased the volatility of the gold from 3, 20, and 62 percent of the total gold to 62, 93, and 100 percent at 200°, 300°, and 400° C, respectively. Chemical analyses of the condensate indicated the volatile species to be FeAuCl6.

Jan 1, 1971

By L. B. Pankratz

The Bureau of Mines conducted heat-content measurements above 298.15° K for dehydrated analcite (NaAISi2O6) to 1,000°K, kaliophilite (KA1Si04) to 1,800° K, and leucite (KAlSi206) to 1,800° K. Heat content and entropy increments were tabulated, and the heat content data, were given in equation form. A first order transition was noted for kaliophilite near 810° K with a heat absorption of 160 cal/mole. Leucite had a second order transition which became complete near 955° K. In this transition a crystal change occurred from tetragonal (low-temperature form) to cubic (high-temperature form).

Jan 1, 1968

By Maria I. De Rosa

This report analyzes mobile equipment fires for all U.S. surface and underground coal and metal/nonmetal mining categories by state and 2 year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from MSHA mine fire accident publications and verbal communications with mine personnel. The analyses will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the hazards associated with mobile equipment fires and will create a basis for future fire research programs.

Jan 1, 2004

By Donald R. Johnson

Apparatus developed by the Bureau of Mines for thermal analysis of oil shale was used to determine the thermal properties of shortite. Dissociation of shortite near 470° C occurs as an endothermic reaction that could consume significant quantities of heat in the oil-shale retorting process that produces shale oil. The shortite dissociation products undergo other thermal reactions that would not affect the retorting process. These reactions include crystal inversions near 365° C and 425° C and melting and decomposition endotherms above 500° C. Two separate reaction route for fusion and decomposition of the shortite decomposition products are dictated by the presence or absence of CO2 around the sample.

Jan 1, 1974

By Gordon L. Kinney

Following a year of great uncertainty, the political situation in Bangladesh improved during 1976. The major problem for Bangladesh remained the high birth rate and crowded conditions. Bangladesh had the highest population density of any agrarian country--over 80 million people in a land area of 144,000 square kilometers, 65% of which is considered arable. The Government, with considerable foreign assistance, was actively encouraging voluntary family planning, and set a growth rate target of 2% per year or less. However, even if the growth rate was reduced to the target level immediately, the population of Bangladesh would nevertheless nearly double within 20 years.

Jan 1, 1980

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and 2-year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 1, 2004

1. Mining to prevent and control underground acid formation should begin with education imparted through: (A) Course work at mining schools to teach prospective engineers. (B) Training of engineers presently employed in the mining industry through appropriate mining extension courses. 2. Considerable need exists to devote more attention to: (A) Hydrogeologic studies of mining areas to enhance the planning of new mines and the abatement program of existing mines. (B) Additional research to explore methods of dewatering the strata associated with mining areas. (C) Further effort to develop sealants for preventing contact between water or oxygen and the acid producing material associated with the coal seam.

Jan 1, 1970

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

The program MFIRE consists of four files MFIRE0 EXE, MFIRE1 EXE, MFIRE2 EXE, and MFIRE BAT The batch file, MFIRE BAT, controls the operation and cooperation of the three executable pro¬gram files and the output Networks of up to 500 air¬ways and 350 junctions can be modeled in the PC version of MFIRE Larger data sets can be accommodated by increasing array dimensions and compiling the program again. Input for MFIRE is in the form of a data file The data file contains fines of numerical data describing the physical mine, the ventilation parameters present, the fans, and the proposed thermal or mechanical disturbances

Jan 1, 1990

By Kenneth B. Higbie

Expenditures to advance scientific technology in general reached an all time high in 1965 with some $22.2 billion estimated to have been allocated by government and industry. Federal Government expenditures were estimated at $15.4 billion, with almost 90 percent of the funds devoted to programs involving defense, atomic energy, and outer space efforts. With this massive effort in the United States and a very impressive effort elsewhere in the world, there is little wonder that many new metallurgical developments were announced in the technical press during the year. No effort has been made to cover all aspects of the industry, but a few of the developments are described in this chapter.

Jan 1, 1966

By T. R. Jolley

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: I. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in the county series that describes the preparation characteristics of the coals of Bell County, Ky.

Jan 1, 1957