Search Documents

By Irving Hartmann

Following the severe starch-dust explosion in the casting department of a large candy factory nearly 2 years ago, great interest has been shown in the explosive properties and the safe manufacture and handling of powdered starches. Under the auspices of the National Fire Protection Association, a committee has been formed to prepare a code aimed at preventing dust explosions in the confectionery industry. One objective of this code will be to reduce the explosion hazards of starches that are widely used for molding, dusting, and other candy-manufacturing processes. The explosibilities of starches and starch mixtures have been studied in the laboratories of the Bureau of Mines and elsewhere. The results of the initial experiments made by the Bureau on 10 samples of cornstarch and mixtures of cornstarch with other materials have been published. In response to numerous requests for additional information, further laboratory studies have been conducted. Data have been obtained on the effects of dust concentration, particle size, moisture content, admixture of .calcium carbonate, and on the effect of oil treatment on the explosibility of cornstarch. The results of this investigation are summarized in this report.

Jan 1, 1950

By Murray Jacobson

The Federal Coal Mine Health and Safety Act of 1969 established mandatory dust sampling of coal mines according to procedures prescribed in the Mandatory Health Standards, title 30, Code of Federal Regulations, part 70, published in the Federal Register on April 3, 1970. A laboratory was established in the Pittsburgh Field Health Group of the Bureau of Mines to process the coal mine dust samples collected by the mine operators. This paper describes the laboratory and presents the equipment and procedures used in processing these samples.

Jan 1, 1971

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed-limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and sup-plies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By E. L. Garton

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 3134, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and January and March, 1932, as published in Reports of Investigations 3140, 3147, 3150, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active Permissible list: Austin Red Diamond No. 1, L. F. Gel-Coalite W, L. F;" Austin Red Diamond No: 5. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.

Jan 1, 1932

By Robert E. Johnson

THE MILDEST recession of the postwar period ended in the first months of 1961, and the economy climbed steadily during the remainder of the year. The Federal Reserve Board (FRB) Index of Industrial Production climbed from a low point of 102 (1957=100) in February to 115 in December, a rise of 12.5 percent. But economic activity for the year as a whole was only 1.5 percent higher than the 1960 level, as measured by real gross national product (GNP). Although activity increased throughout 1961, much of it was merely regaining ground lost in the decline during the second half of 1960 and the first months of 1961. The FRB index did not re ain the July 1960 high of 110 until June of 1961. Mineral fuels did not fully share in the economic recovery. The (FRB) crude oil and natural gas index rose only 5 percent between February and December. Although the index of monthly coal production increased 11.5 percent during the year, the February level was so low that total production for the year was the lowest since 1954. Total production of energy measured in Btu's was up slightly (1 percent) during the ear. Coal production was down; production of crude oil and natural gas was up. Calculated consumption paralleled production-total up slightly, coal lower, and crude oil and natural gas higher. The most interesting product developments were in coke and residual fuel oil. Sales of coke showed a sharper drop than steel

Jan 1, 1962

By R. L. Grayson, T. Simonyi, R. A. Andrel

"The purpose or this paper is to disclose analytical, statistical, and observational results relating to mineralogy and trace elements in respirable dust samples collected from two different mines in West Virginia. Samples were taken from longwall panels, and the panels operated in different coal seams, one located in the northern part or the state and the other in the southern region. Mining conditions and equipment arrangements on the panels will be described along with dust control techniques used. Results from sample analyses are summarized with emphasis on relationships between mineralogy, trace elements and mineral particle size to worker locations. Correlations are made between micro x-ray diffraction and energy dispersive x-ray analyses for sample mineralogy.IntroductionThrough the work of many researchers worldwide, the health of coal miners in modern societies is now protected from harmful exposure to respirable coal mine dust. A vast amount of research culminated in the exposure-response model of Jacobsen, et al, (l) which has been used to establish the 2 mg/m3 exposure limit in the United States. According to the model exposure to respirable dust for 35 years at this level or less could prevent the occurrence of a clinically significant case of coal workers' pneumoconiosis (CWP) in a miner. The exposure limit, of course, must be adjusted whenever greather than five percent free silica exists in the respirable dust.The Jacobsen model was built around a mean mass concentration exposure, which generally showed the highest correlation with both incidence and progression of CWP. As Morgan, et al noted, however, the quantity of respirable dust inhaled is not the only significant factor. 2) They noted that although mass of respirable dust correlates highe.st with the incidence of CWP, it is not a causal factor. Admittedly, the insidious processes causing the disease occur at the lund cell-dust particle level."

Mar 1, 1989

By J. D. Davis

From the chemist's point of view it would be ideal if specifications for coke for any stated purpose could be written on the basis of chemical composition and burning characteristics. Unfortunately this is not possible. In fact, the physical properties of a coke are often of such major importance as to render any specified chemical requirements totally inadequate to show the quality of coke desired. For example, a furnace coke may admirably fill all chemical requirements, such as for low phosphorus, sulphur, moisture, and high fixed carbon, and still be too soft to support the burden of the furnace without excessive crushing. Again, a domestic coke though a good fuel as judged from Chemical analysis, may be of unmarketable size. Thus one can not define the quality of a coke for a specified purpose without taking into account both its chemical and physical characteristics even when this has been done the specification may fail because neither coke user nor producer can accurately define by quantitative tests the qualities most desired. In other words, there is need of accurate test methods for measuring the properties of coke and, what is equally important, for correlating the results with the behavior of the coke in use. Coke quality is determined by the kind of coal used, the coking process, and the type of equipment used in the coking process. Chemical analysis of the coals, together with small-scale coking tests, will give a good indication of their suitability; but, in general, coke must be produced on an industrial scale and tested in the equipment for which it is intended before conclusive information as to its quality is obtained.

Jan 1, 1928

By T. W. Goodman, J. Cervik

The Bureau of Mines conducted studies to compare the effectiveness of the cross-measure borehole system with that of surface gob holes on two successively mined retreating longwalls in the Lower Kittanning Coalbed. Only the cross-measure system was in operation on panel A; on panel B, both systems were in operation. In addition, the cross-measure bore-holes on panel B were drilled parallel to the face, whereas those on panel A were drilled at a 45O angle with respect to the longwall axis. The studies show that the cross-measure system captured 71 pct of the methane generated by longwall mining on panel A. On panel B, the sur- face gob hole dominated over the cross-measure system for about 700 ft (213 m) after it was intercepted. Beyond that point, the cross-measure system dominated. About 93 pct of the methane generated on panel B was captured by the two systems. Cross-measure boreholes that were drilled parallel to the face were as effective as boreholes oriented 45" with respect to the longwall axis. In addition, they are shorter and require less drilling time. Comparison between observed gas pressure differentials in boreholes and calculated values indicate that boreholes can be shortened further to 140 ft (43 m). Additional studies are needed to verify these calculations.

Jan 1, 1986

By G. W. Jones

[A survey of the literature relating to ignition temperatures of acetylene-air and acetylene-oxygen mixtures reveals rather wide disagreement in the reported results. In some instances the ignition temperatures of acetylene-air mixtures were reported to be lower then those of acetylene-oxygen mixtures, which is contrary to experience with other combustibles. To clear up some of the reported discrepancies, the authors have investigated the ignition temperatures of acetylene both in air and oxygen, and their results are presented in this report.]

Jan 1, 1941

By D. Caruso

The health and financial costs of cumulative injuries are plaguing the mining industry. Industry leaders are concentrating on reducing the risk of injury to their workers through design and redesign of work environments. While ergonomics is not a currently regulated field, many mines are realizing that the only way to tackle their most costly injuries, cumulative injuries, is to make the proactive choice to understand those injuries, their root causes and to make workplace changes to prevent them from occurring. Reduction of these injuries not only improves the health and morale of the workers but increases productivity and profit for the companies. Knowledge and reporting of ergonomic risk factors by employees and ergonomics committees is key to these changes and to the reduction of cumulative injuries. NIOSH is developing strong relationships with industry associations and equipment manufacturers to leverage their communication abilities to transfer knowledge to their customers and make a difference in the health and safety of U.S. miners. The benefits of a formalized approach to reducing these injuries along with examples will be presented.

By D. J. Parker, D. Harrington, L. H. Harrison

The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient. points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of, life and damage to property, with special application to the mining industry The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment,, through improved types of lightning arresters,, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures. LIGHTNING PHENOMENA In 1751, Franklin proved that lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition, to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

By Thomas P. Holden, Todd M. Ruff

Problem: An average of three workers a year are killed in surface mining operations when a piece of haulage equipment collides with another smaller vehicle or a worker on foot. Another three workers are killed each year when haulage equipment backs over the edge of a dump point or stockpile. Devices to monitor the blind areas of mining equipment are needed to provide a warning to operators when a vehicle, person, or change in terrain is near the equipment. Method: A proximity warning system (PWS) based on the global positioning system (GPS) and peer-to-peer communication has been developed to prevent collisions between mining equipment, small vehicles, and stationary structures. Results: A final system was demonstrated using one off-highway haul truck, three smaller vehicles, and various stationary structures at a surface mining operation. The system successfully displayed the location of nearby vehicles and stationary structures and provided visual and audible warnings to the equipment operator when they were within a preset distance. Summary: Many surface mining operations already use GPS technology on their mobile equipment for tracking and dispatch. Our tests have shown that it is feasible to add proximity warning to these existing systems as a safety feature. Larger scale and long-term tests are needed to prove the technology adequately. Impact on Industry: A PWSs that incorporates a combination of technologies could significantly reduce accidents that involve collisions or driving over an edge at surface mining operations.

By John Zetterstrom

Increased activity in the beneficiation of taconite, particularly the magnetic variety, has shown the need for more information on the rate of oxidation of magnetite to hematite. This oxidation occurs in the pelletizing step of the beneficiation process. Magnetic taconite is an intimate association of magnetite and a siliceous gangue. It must be ground to approximately 70 to 30 percent minus 325 mesh to liberate the magnetite from the gangue. With sufficient liberation, magnetic concentration will yield a product high enough in iron and low enough in silica for blast-furnace use. The magnetic concentrate must be agglomerated before it can be used in a blast furnace. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron-oxide materials, sintering and pelletizing being the two most common methods. Sintering is clone on a Dwight-Lloyd or Greenawalt sintering machine. Pelletizing consists of balling fine, moist oxide in a rotating drum, followed by baking at .a temperature below that of incipient fusion to develop a permanent bond within each pellet. The magnetic concentrate from taconite is too fine for good sintering practice but fine enough for good pelletizing practice.

Jan 1, 1950

By L. G. Marshall

The geology, mining, beneficiating, types of products, and costs in terms of percent of total costs and of labor, power, and supplies of two crushed- limestone operations in Madison County, Iowa, are described in this paper. The operations are basically similar, differing in refinements in mining, product types, and markets. The operations are comparable as to personnel and as to weighted costs in terms of percent of total costs and in terms of man-hours, power, and supplies. The waste-to-stone stripping ratio is 1 to 0.8 at both operations, the powder factor is 0.29 pound of explosives per ton of stone, and daily production is 95 tons per man-shift. Both companies use crawler-mounted diesel shovels for loading, truck transportation, wagon drills, and dry screening.

Jan 1, 1963

By W. E. Wallace, C. A. Hill, M. J. Keane

"Diesel exhaust particulate material from exhaust pipe scrapings of two trucks, diluted automobile diesel exhaust particulate material collected on filters, and two oil shale ores were prepared for the Ames mutagenrcity assay by dichloromethane OOP ex¬traction, by dispersion into 0.85% saline, or by dispersion into dipalmitoyl lecithin (DPL) emulsion in saline. Salmonella typhimunum TA98 was used to detect frameshift mutagens in the samples. Samples of diesel soot gave positive mutagenic responses with both DCM extraction and DPL dispersion, with the DPL dispersion giving higher results in some cases. The results suggest that possible mutagens associated with inhaled particles may be dispersed or solubilized into the phospholipid component of pulmonary surfactant and become active in such a phase.INTRODUCTIONThe Ames Salmonella/microsome assay (Ames et al., 1975) has been shown to be a useful test for detecting genotoxic properties of various agents. Hundreds of specific chemicals have been screened (McCann et al., 1975), and the test has been applied for many types of environmental samples. Airborne mutagenic agents, for example, have been found in urban air (Chrisp and Fisher, 1980; Hughes et al., 1980; Ro· senkranz et al., 1978), in diesel engine exhausts (Huisingh et al., 1978), and in the by-products of coal combustion processes (Chrisp et al., 1978).Samples of airborne particles are typically collected on membrane filters, and undergo a rigorous extraction procedure with organic solvents and/or ultrasonic agitation (Clark and Hobbs, 1980). Often extracts are transferred to another solvent that is compatible with the assay system. These extraction procedures, while efficient from an analytical perspective, are not physiologically plausible. The questions that present themselves are whether a demonstrated mutagen can be taken up in vivo and whether the process is quantitatively or qualitatively different from the above laboratory procedure (Wallace et al., 1984).When a particle of respirable size is inhaled to the alveolar region of the lung, its first physiological contact is with pulmonary surfactant that lines the inner surfaces of the alveoli. This surfactant is an aqueous fluid containing proteins, phospholipids, and other components (R. J. King, 1982). The principal phospholipid constituent is L·alpha-phosphatidylcholine, beta,gamma-dipalmitoyl, or dipalmitoyl lecithin (OPL) (l. C. King et al., 1981)."

Jan 1, 1989

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974

Provide reliable, early-warning fire detection instruments, telemetry, and control systems for noncoal underground mines. Approach Industrial-grade fire detection instruments and signal telemetry equipment were modified for long-term exposure to harsh underground mine conditions, then were installed in four mines to evaluate long-term performance and reliability. How It Works The elapsed time between the onset of a fire and its detection is critical because fires tend to grow in size and intensity with time. Early fire detection and warning permit the initiation of a mine's emergency plan (evacuation, fire fighting, etc.) while the fire is still small, or ideally, while it is still in the incipient stage. Fire detection and warning systems, utilizing sensitive heat, flame, smoke, and gas analyzers, provide the most rapid and reliable indication of a developing fire.

Jan 1, 1987

Develop computer software that can aid in improving the visibility and illumination in underground mines by providing quick analysis of existing equipment and conditions and the effects of potential modifications. Background Poor visibility and illumination are common problems in underground mining. Mining equipment often restricts operators' fields of vision. Also, fighting systems are often positioned where they cause excessive glare, which restricts the visibility around the machines even further. To help address these problems, the U.S. Bureau of Mines (USBM) has developed a PC-based software package to analyze certain human engineering aspects (ergonomics) of mining equipment design. The software is available for use by equipment manufacturers and mining companies for design work on new machines, as well as for evaluating proposed modifications to existing machines. Approach The Crewstation Analysis Programs (CAP) package includes assessments of visibility, illumination, and glare in the surrounding work area. The advantage of using computers for these types of analyses is that numerous design iterations can be tested quickly and efficiently to determine the effects of changes on visibility. This cuts down the need for expensive testing using physical mockups. Another advantage is that design ideas can be tested in situations where testing would not normally be possible. For instance, the effects of modifications to a lighting system or canopy design could be tested while the machine remained in service.

Jan 1, 1993

In the U.S. coal mining industry, a large cohort of miners is at or nearing retirement age. As these miners retire, there will be a need to hire and train thousands of new and most likely younger workers. Moreover, a large portion of safety trainers will also require replacement due to retirement. In a speech before the U.S. House of Representatives (2004), Bruce Watzman, Vice President for Safety, Health and Human Resources for the National Mining Association said, “[W]e will need to replace a major portion, approximately 50%, of the underground coal mining workforce within the next 5–7 years.” The large influx of new mine workers, along with the deficit in safety trainers, creates the challenge to provide consistent and effective safety training. Given the expected high turnover of the mining workforce, it is very likely that incoming workers will have much less experience than those leaving the workforce. Unfortunately, inexperienced miners have been shown to incur the highest rate of injuries. The piece of machinery most associated with these injuries is the roof bolting machine, which accounts for 56% of machinery-related injuries in underground coal mining. The National Institute for Occupational Safety and Health (NIOSH) has released a new report entitled “Roof Bolting Machine Operators Skills Training for a Walk-Thru Roof Bolter: Trainer’s Guide” (IC 9489). It is designed to help safety trainers develop struc-tured training for new operators of walk-thru bolting machines. This resource will help trainees learn, understand, and apply knowledge and skills. Included in the trainer’s guide are the following tools: [ ] a six-part DVD video series, a skills check survey, talking points, and a complete job training analysis. Also included is an exercise to help trainees learn more about their mine’s roof control plan, as well as a list of supplemental training and reading materials. On-site trainers can modify this guide to fit their particular mine conditions, machines and equipment, and work procedures. The goal of every coal mine safety professional is to increase safety awareness and make mines a safer place to work. The Walk-Thru Bolting Machine Trainer’s Guide will help teach new miners skills to create a safer working environment that will ultimately prevent or reduce on-the-job injuries. Safety trainers can also use the ideas and concepts from this guide to develop their own training skills for the safe operation of other pieces of underground coal mining equipment.

Jan 6, 2007