Search Documents

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

By R. S. Conti, C. D. Litton

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide(CO) sensors, and a point type heat sensor (PTHS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s. The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS. A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and CO sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity. Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners’ escape.

Jan 1, 1995

"Fire fighting in metal mines under the best of conditions is a dangerous, a slow, and a difficult task. Certain gases generated from combustible material burning in restricted areas are poisonous, even in small quantities, and can not be breathed without serious and often fatal results. In addition to poisonous gases, smoke is given off which obscures the vision of the fire fighter and frequently prevents him from gaining access to the fire area. Many fire-fighting crews have had to turn back because their vision was so impaired by the dense smoke that the fire area could not be located and there was danger of them becoming lost in the mine.In mines having mechanically controlled ventilation - that is, mines not dependent entirely upon natural air currents - the gas and smoke can be forced ahead of the fire-fighting crews, thereby facilitating exploration of the mine and saving the time, energy and oxygen of the mine rescue apparatus crews.Where currents of fresh air can be circulated up to points near the fire without danger of seriously spreading the fire, fresh air bases can be established in the immediate vicinity, and a more intelligent campaign for fighting or controlling the fire can be mapped out.Positive air currents through forced ventilation may also result in saving the lives of miners who otherwise might have been trapped in smoke and poisonous gases.It is generally known that comparatively few metal mines have attempted to regulate or control air currents, with the result that when a fire occurs underground, the normal ventilation may be reversed, short circuited, or the air current may be in one direction one minute and in the opposite direction the next; or, generally speaking, the ventilation can not be depended upon, and smoke and poisonous gases may accumulate in any part of the mine or ""drift"" on the fire-fighters or on the miners endeavoring to escape."

Apr 1, 1921

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines' horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau's methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By E. D. Gardner

An explosion occurred in a high-pressure compressed-air line in October, 1930, at an Arizona copper mine. The explosion was unusual, and nothing had teor. noted by the plant operators to indicate the possibility of such an occurrence. It is necessar The air is The mining company uses compressed-air locomotives to haul about 4,500 tons of ore per day from the stopos to the pockets at two hoisting shafts. The ore cars hold five tons each, and are pulled in trains of 30 cars. to charge the locomotive with compressed air at both ends of the trip. conveyed from the compressors at the surface to the distributing points unier roun in special high-pressure four inch steel pipe that was tested to withstand 2500 pounds per square inch before being installed. The air is delivered to the loco- motives at a pressure of 1000 pounds per square inch. There are no receivers in the system. The air for running the locomotives is compressed by one three-stage and two four-stage compressors which have capacities of 600 and 300 cubic feet per minute, respectively. These machines are operated by electric power, and are in an end of the main compressor building in which air is compressed to supply the air drills in the mine. Whenever the demand decreases, as at the noon hour, one or more of the Compressors are shut down. On this particular occasion, at the end of the noon hour, one of the operators was approaching the high-pressure compressors to start the two smaller machines that were not running, when the explosion took place under the floor a few fost ahead of him. The man was mocked down and received some superficial cuts and bruises, but was not seriously injured. The floor was torn , the side of the building blown out, and holes imo cited in the roof some twenty feet above. The explosion was immediately followed by a fire which was quickly put out by the plant operators with hand fire extinguishers. At the time of the explosion the 600 cubic foot compressor was running alone, and the pressure in the system at the machine registered 1040 pounds por square inch. On examination it was found that two 6-fout sections of pipe, about tan feet apart, were completely ruptured into twisted fragments; the rest of the pipe line, apparently, was not injured. The destroyed sections were in that part of the pipe near the large compressor and above the connection from the two smaller machines. It is not definitely mom what caused the explosion. Explosions in other compressed-air systems have taken place, and, although of rare occurrence, have caused loss of life. Such explosions are not confined to high-pressure installations and several have occurred at plants compressing air te one hundred pounds per square inch, or less. plosions of this nature are not to be confused with the rupturing of compressor cylinders from excessive air pressure caused by the discharge valve being closed.

Feb 1, 1921

By A. H. Warner

Sphalerite crystals occur sparingly in minor faults and pockets in a coarsely crystalline dolomite on the Brown-Tipton farm near Greenville in Greene County, Tenn. After several visits by U. S. Bureau of Mines engineers and U.S. Geological Survey geologists, a survey was r: the in the fall of 1944. Upon their recommendations, trenches on the Brown farm under Bureau of Mines supervision. In each case, the bed most favorable for zinc deposition was exposed. In the finished trench bottoms no zinc minerals are visible.

Jan 1, 1950

Part Two of this report is based upon six working memoranda prepared during the first half of 1972 at an early stage in our work for the Bureau of Mines. This work presents preliminary performance estimates of baseband voice and narrowband through-the-earth electromagnetic communications systems of principal interest to the Bureau for operational/ emergency mine communications applications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; on theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau and on semi-empirical models which describe the intelligibility of voice communications as a function of the frequency variations of the signal-to-noise ratio across the voiceband. This work examines the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, and uplink transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/ meter (high) were used; the former figure for both voice and narrowband calculations and the latter for narrowband calculations only. Examples of high, moderate, and low, surface and subsurface, harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low-levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. The effects of simple voice spectrum shaping techniques on the intelligibility of through-the-earth voice communications are examined, and indexes of intelligibility more broadly based than signal-to-noise ratio are discussed. Finally, a means of overcoming the affects of 60 Hz noise and its harmonics which are the largest contributors to typical audio frequency in-mine noise, is suggested. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 1, 1974

By Kenneth L. Rubow, Virgil A. Marple, Bruce K. Cantrell

"In a cooperative study by the University of Minnesota and the U.S. Bureau of Mines, diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and in five underground coal mines. Three mines utilized diesel-powered haulage equipment and two used all-electric equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations measured. The first technique, using a micro-orifice, uniform deposit impactor (MOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of the aerosol is predominantly submicron and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance (CMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 µm. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling.Based on the results from the size selective sampling, a personal diesel aerosol sampler has been developed for measuring diesel aerosol mass concentrations. Th.is sampler uses an inertial impactor to size separate the respirable aerosol at 0.8 µm. All material less than 0.8 µm is collected on an after filter for subsequent gravimetric analysis."

Jan 1, 1990

By Oliver Bowles

The United States Bureau of Mines has within its ranks a group of engi- neers who are engaged in working out quarry problems, the solution of which will be of general benefit to the industries involved. The problems undertaken are approached in a systematic and thorough manner, all the evidence for and against any proposed change or new development being collected as carefully as an attor- ney would prepare his data on an important case. Unlike the attorney, however, the Bureau engineer does not take sides; his judgment is based entirely and in- partially on the array of facts presented. In order to gain the desired infor- mation he visits many plants, consults with the leaders in the industry, works out experiments in his laboratory, and supplements this information with a stu- dy of all available literature already published on the subject in any part of the world. As an engineer who has for eight years conducted such inquiries in the stone industry, I propose to discuss the Bureau of Mines viewpoint; and it may be of interest to consider with me in a brief and general way the engineer's method of looking at quarry problems, and some of the results attained through past and present labors. While the Bureau has conducted no investigation directly for the crushed- st one industries, two years of investigative work at cement-plant quarries, and work now being conducted at lire-plant quarries, has a very direct bearing on the problems of the crushed-stone industry, since stripping, drilling, blasting, loading, and transportation are similar in many respects in all stone quarries. The results of cement-plant quarry investigations are to be found in Bureau of Mines Bulletin #160. (b) Two short papers on lime-plant quarry problems have been issued in mimeographed form as Serial #01 (c) and Serial 3 (d).

Jan 1, 1923

By Wm .. W. Odell

There is outlined below the essential facts brought out in an investigation into the causes for emulsion difficulties as experienced at many water gas plants . The investigation was conducted under a cooperative agreement between the University of Illinois Engineering Experiment Station , the Illinois State Geological Survey , and the U. S. Bureau of Mines . Funds of the Illinois Gas Association were used to defray a part of the costs . Active assistance was rendered by the Peoples Gas Light and Coke Company , of Chicago , who furnished a laboratory at Chicago for conducting the experiments , and loaned the services of Mr. E. A. Thiele to help with the laboratory work . A full report on the results of this work will be published by the Bureau of Mines later but it is believed desirable to bring the principal results now to the attention of the industry . In almost every gas plant where carbureted water gas is made , some difficulty is experienced , at one time or another , in separating the tar fran the water that condenses from the gas . The fact that annoyance from this source is ever present in some plants , and seldom present in others , leads to the belief that certain operating variables have considerable to do with the formation of difficulty separable tarwater emulsions . Accordingly , when samples of tar were collected for laboratory study , the operating conditions and methods were simultaneously observed and recorded.

Mar 1, 1922

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX D DEVELOPMENT AND EXPERIMENTAL VERIFICATION OF ACOUSTIC SEAL CHECKER THEORY 1. Introduction In Section 7 of the report the acoustic seal checker concept was described in a general manner and the parameters which affect the signal level at the microphone were discussed briefly. In this appendix the theoretical basis will be presented and the experimental program described which permitted the extension of the theory into practice. The basic goal of the acoustic seal checker is to relate the reduction in sound pressure level to the size of the residual hole in the fly ash barrier. The smallest hole size that may be measured is determined by the signal to noise ratio, where the noise in this case includes the ambient noise in the mine, the internal microphone noise and the sound transmitted from the acoustic source via the flanking paths through corridors adjacent to the one being sealed. The latter source of noise can be discriminated against, at the expense of increased complexity of the acoustic system, by employing a pulsed source and pulse gating of the microphone signal set to accept sound via the barrier path and to reject the delayed flanking path signals. In order that the acoustic system be insensitive to precise source and microphone location and to permit assessment of system performance on an acoustic power flow basis, a broad frequency band of pseudo-random noise is emitted by the loudspeaker source. The preferred frequency range must be determined, the advantage of a directive source must be assessed, and the necessity

Jan 1, 1973

By D. Harrington, M. W. Von Bernewitz

Sections 120 and 121 of Article XI. Fire Control, of a proposed Mine Safety Law in preparation, to be used as desired and when approved by any State, contains these provisions: After the adoption of these regulations, no mine operator shall erect any nonfireproof structure within 50 feet of any mine entrance. or airway. Every operating mine having nonfireproof structures within 50 feet of any mine entrance or airway, except headframes necessary for hoisting, shall have such structures fireproofed or removed and replaced with fireproof structures within six months of the adoption of these regulations. Before reopening, mines idle at the time of the adoption of these regulations shall have all non- fireproof structures fireproofed, removed, or replaced with fire- proof structures as required by the foregoing sentence. Upon receipt of the written statement of a mine operator that the fireproofing of existing structures is impracticable, the chief mining engineer (of the State commission) shall satisfy himself as to the abouracy of the statement. If he concurs that fireproofing is impracticable, and if at the same time he holds the opinion that adequate protection can be provided otherwise by such procedure, he shall have authority to issue a written permit for the substitution of fireproof door at or near portals of mine openings and collars: of shafts. Such doors shall fit as nearly gas-tight as possible. and shall be installed in such a way that the mouths of mine open- ings can be closed readily from outside of structures. The effec- tiveness of such permit may be made contingent upon the operator's continued compliance with any additional precautions which are necessary in the chief mining engineer's opinion to protect the lives of miners.

Mar 1, 1932

By Robert H. Dickson

This paper describing the mining practices at the Verde Central mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods and costs in various mining districts of the United States. ACKNOWLEDMENTS The costs contained in this paper were prepared by R. J, Huddleston, chief clerk, Verde Central Mines, Inc.

Jan 1, 1931

By Thomas V. Falkie, R. Venkataramani

Anderson, L. B., 1963, "Multiple Regression Techniques Correlate Experimental Data," Chemical Engineering, V. 70, N. 12, pp. 223-228. Aubert, E. J., Lund, I. A., and Thomasell, A. J., 1959, "Some Objective Six-Hour Predictions Prepared by Statistical Methods," Journal of Meteorology, V. 16, pp. 436-46. Barrett, A. L., 1958, "Alternating Current in Continuous Mining," Mechanization, V. 22, N. 9, pp. 83-86. Bower, A. B., Jr., 1970, "Bit Design: Key to Coal Cutting," Coal Age, V. 75, N. 7, pp. 70-72. Bower, A. B., Jr., 1971, Personal Communication dated April 29, 1971; General Electric Company, Mining and Metallurgical Products Department, Detroit, Michigan. Burt, C., 1950, "Group Factor Analysis", British Journal of Statistical Psychology, V. 3, pp. 40-75. Cady, L., Gertler, M., Gottsch, L., and Woodbury, M., 1961, "The Factor Structure of Variables Concerned with Coronary Artery Disease", Behavioral Science, V. 6, pp. 37-41. Cattell, R. B., 1965, "Factor Analysis: An Introduction to Essentials I. The Purpose and Underlying Models," Biometrics, V. 21, N. 1, pp. 190-215. Christensen, R. W., Heins, R. W., Babcock, W., and Tonn, R., 1971, "The Effect of Material Properties on Materials Handling Processes," Six Month Technical Report, (August 1971) to Advanced Research Projects Agency, U. S. Department of Defense; The University of Wisconsin. Collins, G., 1961, "Factor Analysis," Journal of Advertising Research, V. 1, N. 5, pp. 28-37. Cooley, W. W., and Lohnes, P. R., 1962, Multivariate Procedures for the Behavioral Sciences, New York: John Wiley and Sons, Inc. Cree, J. 0., 1956, "Power for Continuous Mining," Mining Congress Journal, V. 42, N. 10, pp. 49-52. Draper, N. R., and Smith, H., 1966, Applied Regression Analysis, New York, John Wiley & Sons, Inc. Griffiths, J. C., 1966, "A Genetic Model for the Interpretive Petrology of Detrital Sediments," The Journal of Geology, V. 74, N. 5, pp. 655-672.

Jan 1, 1972

By Fred N. Kissell

A self-sealing brattice intended for use during coal mine rescue and recovery operations has been designed and tested by the Bureau of Mines. The major design difference between self-sealing and conventional brattice is that the fabric is cut and sewn BS a hemisphere instead of as a flat sheet. This new type of brattice offers reduced weight, leakage, and installation time. Preliminary testing indicates that the concept is worthwhile, but that further developmental research is required.

Jan 1, 1976

By Edward D. Thimons

A remote-actuated stench gas fire-warning system has been designed and tested by the Bureau of Mines. This system makes use of the hard-wire network for the mine's phone pager system, thus greatly reducing the system cost. By locating stench gas canisters with remote-actuation release capabilities near working sections, the fire-warning time can be greatly reduced. In a test of the system in a Missouri lead mine, the time required to warn miners of a fire at two working faces was reduced from about 20min with the conventional system to less than 4 min with the remote-actuated system.

Jan 1, 1984

By L. F. Willmott

Pulverized high-volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure-gasification pilot plant equipped for slurry feeding. The minimum ratio of water to pulverized coal that could be pumped satisfactorily as a slurry was about 1 to 1. Heating this slurry produced a suspension of coal in superheated steam having a steam-to-coal ratio greater than the 0.3 to 1 proportion that is considered optimum for pressure gasification of pulverized coal. A steam separator removed enough steam to provide ratios down to about 0.5 to 1, but a 0.3 to 1 ratio was not achieved. Gasification of Sewickley coal produced a synthesis gas containing about 36 percent H2, 46 percent CO, and 13 percent CO2, Gas output, gas composition, and coal and oxygen requirements were Virtually the same as for a pilot plant equipped for fluidized-coal feeding. Typical results from the slurry-fed plant at 300 psig were carbon gasified, 95 percent; coal requirement, 34 lb/M (thousand) std cu ft CO + H2 produced; oxygen requirement, 365 std cu ft/M std cu ft CO + H2 produced. The results showed that the two feeding methods are equally satisfactory from the standpoint of gasification. A choice between a fluidized-coal gasification process or a slurry gasification process depends on considerations relating to the coal-feeding phase itself, including capital and operating costs, manpower requirements, safety, and flexibility of operation.

Jan 1, 1962

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

The first phase of our work for PMSRC on this contract was devoted to a comprehensive and in-depth assessment of electromagnetic (EM) noise measurements and data taken by several contractors for use in the design of operational and emergency mine communications. Pertinent measurements and data of other selected investigators were also included in the evaluation. This assessment treated the measurements and instrumentation used, the data analysis and presentation methods, and the utility of the final results. This phase concluded with the identification of the most useful results and methods, the remaining data gaps, the contractor most qualified to fill these data gaps, and the definition (with PMSRC and this contractor - NBS, National Bureau of Standards) of a follow-on noise measurement program, instrumentation system, and data processing methods tailored to obtain the necessary but missing noise data. A partial bibliography of references related to electromagnetic and seismic noise and propagation in the frequency bands of interest was also compiled during this first phase. The body of this Part of the final report presents a summary of the findings of our EM noise assessment, together with detailed recommendations regarding the new noise measurements to be taken and the instrumentation and data processing methods to be used. This work was done during the latter part of 1971 and the early part of 1972. During subsequent phases of the contract ADL was asked to perform on-going evaluations of the continuing program of electromagnetic (EM) noise and propagation measurements made by Bureau contractors, and to utilize pertinent data from these measurements to make performance estimates for

Jan 1, 1974