Search Documents

By H. R. Beard

The citrate process for sulfur dioxide emission control was developed in pursuit of the Bureau of Mines goal of minimizing the adverse environmental impact of mineral-processing operations. This publication describes the gas analysis procedures used during development of the process. The research required the capability to analyze SO2, H2S, CO, CO2, COS, volatile hydrocarbons, NO, NO2, O2, N2, and H2. The methods described include gas chromatography, electrochemical detection, infrared spectroscopy, and the use of a computer program to predict the product composition in complex reactions. Laboratory and pilot plant applications are discussed.

Jan 1, 1979

By C. I. Pierce

This report describes and presents results of a phase of a laboratory study conducted at the Morgantown Petroleum Research Laboratory, Federal Bureau of Mines, Morgantown, W. Va., to determine the response of shielded electrodes of different dimensions in thin, noninvaded beds and to stimulate interest in the use of focused-type logging devices in the Appalachian oilfields. A blotter model was used to obtain plots of the potential field in the vicinity of a model shielded electrode. Three plots are presented. The difference in curvature of equipotential lines and the variation in measured resistance values for different blotter-model conditions suggest that the shielded electrode will give resistivities higher than normal when measurements are taken in a thin conductive bed located between resistive beds, and resistivities lower than normal when measurements are taken in a thin resistive bed located between conductive beds.

Jan 1, 1961

By R. R. Trengove

This paper is one of a series published by the Bureau of Mines on mining methods and operation practices. It describes the open-pit mining method and operations of the Kaiser Steel Corp. Eagle Mountain iron-ore mine, which is in the extreme southeastern part of California 175 miles east of Los Angeles in Riverside County. Nearest town to the mine is Indio, which is 60 miles away by an excellent highway (fig. 1). Elevations at the deposit vary from 1,400 to 3,000 feet. Figure 2 is a plan map of the Eagle Mountain iron mine. Kaiser Steel Corp. built a model camp at the mine, with all modern conveniences (fig. 3). The camp, comprising 145 homes, dormitories, mess hall, commissary, post office, and recreational facilities for 600 people, is at 1,390-foot elevation. The area has winter-resort weather between October and May, with occasional drops of temperature to 25° at night. From June to September temperatures sometimes rise to 1200 during the day. Rainfall is scant, approximately 2 inches a year, the majority of which comes as cloudbursts during the summer months.

Jan 1, 1956

By Walter R. Storms, Allan B. Bowman

This paper , which describes mining methods and practices at the Mineral Hill copper mine , is one of a series being prepared by the Division of Minerals of the Bureau of Mines on mining methods , practices , and costs in various mining districts. of the United States . The Mineral Hill mine is situated on the northeastern piedmont of the Sierrita Mountains at an altitude of 3,650 feet in sec . 35 , T. 16 S. , R. 12 E. , and sec . 2 , T. 17 S. , R. 12 E. , Pima mining district , Pima County , Ariz . ( fig . 1 ) . The claims (figs . 2 and 3) are in a gently rolling area with only scant desert vegetation . The average annual precipitation is about 11 inches . The nearest surface water is the Santa Cruz River , an intermittent stream 8 miles east of the mine . The property is owned by the Banner Mining Co. , a Nevada corporation . This report presents a brief history of the mine , describes the geology of the area and the ore deposits , outlines methods of prospecting and exploration , and gives methods of sampling and the estimation of ore reserves and values . Development and stoping methods are explained , and methods of underground transportation , ventilation , mine drainage , and safety measures are described . The concluding section of the paper is a section on milling . The Mineral Hill mine is an old mine that was reopened in 1951 after having been closed for 30 years .

May 1, 1957

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation's mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By D. T. Hahn

Adequate and cost effective erosion control is an important component in most plans for reclamation of surface mined land. Despite the fact that much is known about erosion of agricultural lands, insufficient conclusive knowledge is available about erosion of reclaimed surface mined land. Our study was conducted to characterize the erodibility of reclaimed surface mine land relative to unmined cropped land, and to evaluate the accuracy of the universal soil loss equation (USLE) in estimating erosion from reclaimed soils. A rainfall simulator was used to measure runoff and erosion rates from plots at three Indiana surface mines. The relation of erosion of the reclaimed soils was not completely constant with that from the cropped soils. Significant differences in erodibility were observed between reclaimed and nonreclaimed top soils, as well as reclaimed topsoils and reclaimed subsoils.

Jan 1, 2011

By R. H. King

A very simple cold-bend test was devised and tested for evaluating thermoplastic jackets used on mine-power-feeder cables. A test sample is bent into a semi-circle whose radius is equal to the minimum bend radius recommended by IPCEA and then cooled to the, desired test temperature (-35°C). While at temperature, the sample is straightened by pulling the cable ends with a winch arrangement. The results show that of the jackets tested, those which cannot withstand the test literally burst when the sample is straightened.

Jan 1, 1978

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By J. B. Gayle

This investigation was conducted by the Federal Bureau of Mines to compare the selectivities of diverse flotation reagents and also of flotation and float-sink methods of separation. Flotation tests, using sodium chloride, an alcohol-type frothing agent, and a kerosine-pine oil mixture as reagents, were made on seven coking-coal samples representing four different beds. The results indicated equivalent selectivities relative to sulfur rejection when entrapment effects were minimized by recleaning the various products. Selectivities relative to ash rejection were also equivalent for some coals; for others, the selectivities of the reagents tended to increase in the order sodium chloride, alcohol-type frother, and kerosine-pine oil. Float-sink tests on these same coals generally gave results indicating better selectivities than those obtained in flotation tests at comparable levels of recovery.

Jan 1, 1960

To minimize the equipment operator?s respirable dust exposure in enclosed cabs of mobile equipment by install-ing cab filtration and pressurization systems and by keep-ing doors and windows closed. Background Enclosed cabs are used on mobile equipment to protect operators from health and safety hazards. The primary health concern is overexposure to respirable dust. Examples of such equipment in mining include drills, dozers, haul trucks, and other equipment. When equipment is new, the operator?s dust exposure is normally at acceptable levels. As the equipment ages and gaskets and seals deteriorate, the air quality inside an enclosed cab can reach a point where it is no longer at acceptable levels for the equipment operators. In an effort to improve the air quality in enclosed cabs of older mining equipment, NIOSH has been performing research to retrofit cabs with new filtration and pressurization systems. Over the past few years, this research has shown that retrofit systems can substantially improve the cab?s air quality back to safe and acceptable levels. How-ever, this is only possible when a positive cab pressure is achieved and maintained. Thus, when a cab door or window is opened, the cab pressure drops to zero and the cab filtration and pressurization system is rendered ineffective. During a recent field study, the magnitude of this impact was noted when a drill operator repeatedly opened the cab door throughout the course of the drill cycle. Upon closer examination, it was determined that the cab door was being opened to manually guide the next drill steel into place each time an additional section of steel was needed to drill deeper holes.

Sep 1, 2008

By Wilbur I. Duvall

In a previous report, entitled A Gage and Recording Equipment for Measuring Dynamic Strain in Rock, a control circuit for a drum camera was described. The purpose of this control circuit was to provide a means for firing seismic caps, synchronizing the firing of the cap with the opening of the camera shutters and generating an electrical impulse at the instant of detonation. The operation of this circuit depended on the following two characteristics of seismic caps: (1) these caps contain a bridge, which breaks at the instant of detonation, and, the firing delay time of the cap is a function of the firing current. During the course of the Bureau's studies, considerable difficulty was experienced from "firing hash", i.e., spurious vibrations that appeared on the records at the time of detonation. The cause of most of this "firing hash" was traced to the intermittent grounding of the cap leads at the time of detonation. As the cap leads were still connected to the firing battery, the grounding of the leads permitted current to flow through the rock to the gage and to return to the firing battery through the shield on the gage cables. The intermittent flow of current along the cable shield produced potentials on the gage leads that were recorded as the "firing hash." To eliminate this difficulty, it is necessary to remove the firing voltage from the cap leads the instant the cap detonates. This report supplements the previous report and describes an improved circuit that can be used to fire seismic caps, remove the firing voltage from the cap leads the instant the cap fires, control the firing delay time in the cap, and generate reference signals at the time current starts flowing in the cap circuit and at the time the cap detonates. These reference signals can be used to determine the firing delay time of seismic caps and the time at which the seismic wave is generated by the explosion.

Jan 1, 1950

By Byron M. Bird

"The prevailing practice of washing unsized coal, 1/2-inch and finer, to 1/8-inch and finer, on a table is subject to certain limitations which are commonly overlooked. In some instances good results are obtained by this method, but often the opposite is true and the efficiency of the washing operation is low. Although the separation taking place on a concentrating table is not fully understood, the actual distribution of particles of various sizes and specific gravities was determined a number of years ago by ore-dressing investigators. Hence this paper consists of an analysis of an old problem by new methods. The experimental data on which the discussion is based were obtained in the course of coal-washing investigations conducted by the U. S. Bureau of Mines at the Northwest Experiment Station in cooperation with the University of Washington and with certain coal operator: of that State.Experimental WorkThe general method of study has been to take a large number of zonal products from the table, and separate them according to specific gravity and size into their component parts. The table used is one of the standard commercial sizes with a diagonal deck. The coal to be washed is split into representative portions, which are stored in separate bins. One portion is used for ""timing as"" the table; the products are collected continuously in the same turned to the feed bin, and thus a closed circuit is completed. When the despite conditions on the table are obtained, coal is fed from one of the re. After the table is operating smoothly the entire product is minute; such a sample is sufficiently large to represent accurately the work of the table and at the same time to minimize the effect of beginning at the end next to the head motion, separate samples are made for each foot along the edge of the deck."

Jun 1, 1926

By E. D. Eastman

The recent determination by Eckman and Rossini of the heat of formation of sulphur dioxide appears to be of much greater accuracy than any previous measurement . The value obtained by them , 70,940 cal . , is in good agreement with that of Thomsen ( 71,080 ) , but differs by about 1,700 calories from Berthelot's result ( 69,260 ) , and by 1,940 calories from the provisional figure ( 69,000 ) adopted by Lewis and Randall in their studies of the free energies of the sulphur compounds . This large discrepancy suggested the desirability of a recalculation of the free energy of sulphur dioxide . In addition it is now possiblt to fix the specific heat of S₂ gas with greater certainty than at the time of the original calculations . These two changes are incorporated in the recalculations described below , and directly affect the values of AH , and the Ar terms in the free energy equation . In the determination of the integration constant of the latter equation , the free energies and specific heats of water vapor and the oxides of carbon are required as auxiliary data . In this work these are based , with certain exceptions , upon the equations previously deduced , which differ appreciably from the corresponding equations of Lewis and Randall . 56 · The principal equilibria employed below , and the plan of calculation , remain the same as in the calculations of Lewis and Randall . Before beginning this revision a search of the literature was made , extending to August , 1930 , for studies of additional equilibria . Only one reaction was found that gives promise of increased accuracy . This is the equilibrium of sulphur dioxide with copper , cuprous oxide , and cuprous sulphide . In this case , however , certain of the subsidiary data are lacking , and until they become available , the existing studies of the equilibrium in this system can not be successfully utilized . The changes in the numerical data mentioned above , especially in the thermochemical constants , are therefore solely responsible for the rather significant differences of the revised from the original values of the free energy .

Apr 1, 1931

By George C. Price

The Bureau of Mines conducted this study in the Roslyn No.5 coalbed in the State of Washington to determine the feasibility of mining hydraulically the portion of the coalbed that was steeply pitching. All of the experimental mining was done while advancing raises and rooms. A Bureau-developed hydraulic mining machine was used successfully in the pitching coalbed. It consisted of a remotely controlled monitor mounted on a self-advancing roof support unit of the type commonly used for roof support in longwall mining systems. The coal cutting rates averaged 0.73 and 0.54 ton per minute in raise and room mining, respectively, while using water volumes up to 230 gpm at a pressure of 4,000 psig. Productivity averaged 4.7 and 5.2 tons per man-shift for raise and room mining, respectively, compared with 7.5 and 8.5 tons per man-shift, respectively, by conventional hand mining methods.

Jan 1, 1965

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By R. Hogg

"Some basic features of the science and technology of particle systems are reviewed in the context of agglomeration processes. Emphasis is placed on the force of interaction among particles and with their environment and on their dependence on particle characteristics and interfacial phenomena. The complex role these forces play in the various stages of agglomerate formation, growth, consolidation and structure development, and their influence on final product properties is discussed.INTRODUCTION Agglomeration is an example of a process where the technology has generally preceded the science. Process development• has very often been by trial-and-error albeit with an eye on some basic principles. Nevertheless there is' a scientific basis to the process and a better understanding of the fundamentals can surely lead to improvements in process design and control.Successful processes for the agglomeration of fine particles depend on proper control of the adhesional forces between particles, to encourage agglomerate formation and growth and to provide adequate mechanical strength in the product. At the same time the rheology of the particulate system can be critical to the rearrangement of particles necessary to permit densification of the agglomerate and the development of an agglomerate structure appropriate to the end-use requirements.AGGLOMERATION SYSTEMSUltimately, the performance, of any agglomeration process depends on the• characteristics of the particles and their environment. The specific effects, however, are often complex and may be very difficult to pinpoint by simple observation of the process. A typical agglomeration process involves a number of concurrent or consecutive steps - adhesion, growth, compaction, etc., - each of which is affected by the characteristics of the system, but not necessarily in the same way. The effect of particle size, say on agglomerate growth may be quite different from its effect on compaction and its optimum value may differ widely from one stage to the other. Obviously there.is a general need for compromise in the design and operation, of agglomeration systems. Furtnermore, an understanding of the details of the process and their complexities can be critical to process optimization and improved product quality control."

Jan 1, 1989

By J. D. Noll

The Mine Safety and Health Administration (MSHA) has promulgated rules to limit the exposure of metal/nonmetal underground miners to diesel particulate matter (DPM). These rules have resulted in many types of control tech­nologies being implemented including diesel particulate filters (DPF). The passive type DPF is the most desirable because it requires little maintenance and it regenerates while the vehicle is operating. One problem with passive DPFs is that many vehicles cannot develop the sustained exhaust temperatures needed to initiate DPF regeneration, and thus it is required that the DPF be catalyzed to decrease the temperature needed for regeneration. In some past studies, such catalyzed filters have been shown to cause an increase in the nitrogen dioxide concentrations in the exhaust, resulting in a potential health hazard. In this study, a lightly catalyzed DPF along with a fuel-born catalyst were employed to help reduce the DPM emissions from a 980F loader used for cleanup in a stone mine. After 30 days of use, the filter continued to regenerate successfully at the exhaust temperatures generated by this loader, substantially reduced DPM concentrations emitted in the exhaust, and did not cause a measurable increase in nitrogen dioxide levels that could be attributed to the device.

Jan 1, 2009