Search Documents

By Michael J. Gallagher

Diamond-bit performance data accumulated by the Bureau of Mines in core-drilling limestone and dolomite show that the physical characteristics of the diamonds and the sizes and types of bits used are economically significant. An analysis of the data establishes one trend of particular significance to those engaged in core drilling: Bits set with small, low-quality drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performance, such as size and quality of diamonds, sizes and types of bits, percentage of core recovered, and physical characteristics of bit matrices are assessed in the tables, bar charts, and discussion.

Jan 1, 1958

By Ernest R. Rodriguez, Allen D. Look

"INTRODUCTION The underground mine of the Miami Copper Co. has operated since 1927 without a fatality from blasting or the handling of explosives. To improve safety and efficiency, electrical blasting has been used exclusively since 1934. During the period January 1, 1934, to December 31, 1948, inclusive, over 4,000 tons of explosives were used to produce 60,925,071 tons of ore with 896,760 feet of development footage and 2,591,788 square feet of undercut area.The purpose of this paper is to recount the company's precautions to insure safe handling of explosives at this operation, where safety involves careful planning rather than ""trial and error.""GENERAL INFORMATIONThe Miami Copper Co. operates on underground mine in a large, low-grade, Porphyry copper deposit near Miami, Ariz. The deposit contains numerous fractures and planes of weakness, which contribute to ease of working the ore bodies by the block-caving method of mining.An individual stope-caving method is used with stoles 150 feet by 200 to 300 feet and 30- to 50-foot pillars between stapes. After the stope is undercut, the ore is drawn through the draw raises on the grizzly level, and thence through the transfer raises to the ore chutes on the haulage level.Access to the mine is by four active shafts, three of which are primarily for ventilation. No. 5 shaft is used for both hoisting and service. There are four operating levels in the mine. The elevations of the grizzly levels are governed by the contour of the bottom of the ore body and therefore vary in different locations in, the mine.Grizzly levels are on the 850, 900, and 975 levels. The 1,000 level is the haulage level. This mine operates in very low-grade ore and requires economical handling of large tonnages safely and efficiently."

May 1, 1950

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

By R. L. Anderson

Mechanical cleaning of bituminous coal in the United States was begun about 1875, with plants in western Pennsylvania and Illinois. The United States Geological Survey began to record the quantity of washed bituminous coal in 1906; and the series was carried forward to 1923, except that no data were collected, for 1922. This statistical work was transferred to the Bureau of Mines in 1925, and the collection of data on mechanical cleaning was resumed in 1927. Data collected before 1927 include only the coal that was washed at the mines and do not include that cleaned by pneumatic methods at the mines and that cleaned at central washeries operated by consumers.2/ The total bituminous coal washed in 1906 was less than 10 million net tons. In 1927, the first year for which complete figures are available for all types of mechanical cleaning, 28 million net tons of bituminous coal were cleaned in the United States.

Jan 1, 1951

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume n of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output!' It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the production of auxiliary processing at or near the mines.

Jan 1, 1979

By F. Chase, D. Pappas

Pillar recovery has been associated with nearly one third of roof fall fatalities in underground coal mines during the past decade. Safe pillar recovery requires global stability and local stability. Global stability is addressed primarily through pillar design. The local stability risk factors include cut sequence, the final pillar stump, supplemental supports (timbers vs. Mobile Roof Supports (MRS)), roof bolting, and many others. The National Institute for Occupational Safety and Health (NIOSH) has evaluated each of these factors through field research and analysis of accident statistics. The paper discusses design methods and technologies that have been transferred to the mining community and implemented.

By Daniel Edelstein

Demand for arsenic trioxide increased markedly during 1984 as a result of increased use of arsenical wood preservatives and increased use of arsenicals in agriculture. The increase in agricultural demand was due to a return to production of land with-held from cotton planting under an agriculture program for acreage diversion for some 1983 crops. Supplies of arsenic trioxide were more than adequate to meet increased demand, and prices either declined from, or remained at, the low 1983 levels. In June, ASARCO Incorporated announced plans to close its Tacoma, WA, smelter by mid-1985. Domestic Data Coverage.-Refined arsenic trioxide was produced by two U.S. companies. The major producer voluntarily reported its production to the Bureau of Mines, but to prevent disclosure of proprietary data, the production data have been withheld.

Jan 1, 1985

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936

By Michael J. Sapko, Eugene M. Bazala, Eric S. Weiss, Kenneth L. Cashdollar

The data presented in this report are the results, to date, of an ongoing Pittsburgh Research Center Disaster5Prevention research program on the explosion hazards associated with blasting operations in noncoal mines. Laboratory and experimental mine tests have shown that oil shale and sulfide ore dusts can be ignited given the proper predispersed dust concentrations, particle size, and kerogen or sulfur content. Methane (CH) gas may also4be present in deep oil shale formations and can pose a significant added hazard to underground blasting operations. The most common explosive used for blasting in oil shale had been ANFO, a combination of ammonium nitrate and fuel oil; blasting in sulfide ore had used ANFO and/or dynamites. Tests conducted at the cannon gallery at Lake Lynn Laboratory near Fair chance, Fayette County, PA, provided a means of evaluating the relative incendivity characteristics of new and existing explosive products. Three explosives—a pumpable emulsion-ANFO blend, a packaged water gel, and an emulsion blasting agent—exhibited low-incendive qualities compared with other more highly incendive products such as ANFO and some dynamites. Based on the data collected during numerous full-scale blasts in oil shale and sulfide ore mines, the low-incendive products significantly reduced or eliminated the ignition hazards while at the same time providing effective fragmentation of the rock. Based on the positive results from the gallery and field testing, low-incendive explosives, coupled with good blasting procedures, show promise in reducing dust and/or gas ignitions associated with blasting operations in oil shale and sulfide ore mining applications.

By Henry E. Blake

The purpose of this Bureau of Mines investigation was twofold. The first phase of the work was to determine the technical and mechanical feasibility of defluorinating low-grade siliceous fluorspars on an intermediate scale by high-temperature pyrohydrolysis in a rotary kiln. The second phase was to react the liberated hydrogen fluoride (HF) offgas with alumina monohydrate to produce commercial-grade aluminum fluoride (85 percent AIF3). The two phases of the work were to be integrated into a single continuous process. Evaluation of the data shows that low-grade siliceous fluorspars can be successfully defluorinated, either in a solid or a molten state, in a gas-fired rotary kiln in the presence of water vapor at 1,250° to 1,350° C. The water produced by combustion of propane was sufficient to yield defluorinatians of 75 to 85 percent.

Jan 1, 1962

By David C. Byrne

PURPOSE: Evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. RESEARCH SUMMARY: The results of previous NIOSH research show that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals and that miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and gender. Using hearing thresholds at 4,000 Hz as an indicator, coal miners experience hearing loss 2.5 to 3 times greater than would be expected for persons not exposed to occupational noise. At age 50, 90% of coal miners and 49% of metal/nonmetal miners were found to have a hearing impairment. In comparison, only 9% of a nonoccupationally exposed control group had a hearing impairment at age 50. There are numerous barriers to the prevention of hearing loss among miners. In an effort to overcome some of these obstacles, this work was initiated to evaluate practical technological advances in level-dependent hearing protectors and inexpensive personal acoustic monitors. Experiments will involve analysis of this new technology under both laboratory and field conditions. Laboratory components will consist of controlled studies using an anthropometrically correct test fixture as well as human subjects to evaluate the adequacy/effectiveness of various hearing protective devices. Electroacoustical performance testing of new noise monitors will also be conducted in a laboratory setting. Subsequent field studies will determine the actual usefulness and practicality of the personal protective/monitoring equipment as used in different mining situations. It is anticipated that increased on-the-spot awareness of hazardous noise levels and the availability of better-suited hearing protectors will provide a degree of protection beyond what is currently attained in different mining environments. Therefore, the intent of this project is to identify and adapt new acoustical technologies and products that have a direct application to individual mine workers. With increased knowledge of these technological advances, a greater demand for similar devices will likely occur, which, in turn, will lead to a better understanding and awareness of hearing loss prevention methods throughout the mining community. The ultimate goal is for widespread integration of useful hearing loss prevention products and devices into the daily routines of miners

Jan 2, 2000

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By R. P. Beyer

Low-temperature heat capacities and standard enthalpy of formation of copper difluoride (CuF2) were determined by the Bureau of Mines. The low-temperature heat capacities were determined from 11 to 302 K by adiabatic calorimetry. The enthalpy of formation was determined by HC1 solution calorimetry. The standard values of entropy (S°) and enthalpy of formation (?Hf°) at 298.15 K are l8.65±0.03 cal/deg mole and -129.02±0.29 kcal/mole, respectively.

Jan 1, 1978

By Bruce D. Sartwell

The Bureau of Mines is using characteristic X-rays produced by proton bombardment of a solid surface to provide quantitative compositional analyses of surface layers of metals. An integral X-ray yield equation has been developed that quantitatively relates the measured X-ray yield to the thickness of thin films ranging from less than a monolayer to several thousand angstroms. The use of the integral yield equation is demonstrated for the growth of a thin film by vacuum evaporation. Results are presented that show haw proton-induced X-ray emission (PIXE) has been used to determine the oxidation kinetics of iron that had been implanted with several different species of heavy ions. The sensitivity of PIXE for the measurement of very-thin-film growth kinetics is demonstrated from studies of the effect of fractional mono-layer coverages of sulfur on the initial oxidation kinetics of iron. Results are also presented in which PIXE has been used to study the redistribution of alloying elements in components of a gas turbine that had fractured due to corrosion fatigue. By combining PIXE with low-energy ion sputtering, quantitative composition depth profiles of surface layers are obtained. Examples are presented for the profiling of iron samples implanted with 25-kev nickel ions and for a platinum coating on an Fe-5Cr substrate.

Jan 1, 1980

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By F. W. Brown, F. C. Gibson

"INTRODUCTION There is urgent need for a satisfactory permissible multiple-shot blasting unit capable of firing 10 detonators in series and safe for use in underground mining where a. gas-ignition hazard may exist.. As there is at present no entirely satisfactory permissible unit of either the battery or generator type, tile described capacitor-battery type has been developed. Consideration of the Bureau of Nines approval schedule pertaining to the generator and magne to-type units and of the electrical characteristics of the unit described in this report indicate that this unit should meet Bureau of Mines permissible requirements.This report gives a detailed description of the design and operation and results of tests to determine safety of operation in gassy atmospheres.DESIGN AND OPERATION OF UNITOperation of the vibrator-type multiple-shot blasting unit is based upon utilization of the discharge energy from a capacitor charged to a given. voltage and having capacitance adequate to store enough energy to initiate 10 detonators in series. The primary source of energy is a 4-volt cap lamp battery such as is carried for illumination on the person of underground workers in nearly all mines. As this battery is already available and is recharged daily it is considered to be a reliable and convenient source of energy for a blasting unit. Figure 1 is a schematic diagram of the circuit for an improved unit, and figures 2 and 3 are views of the experimental unit. The battery potential is applied through a radio-type synchronous vibrator (8) to an 8-volt center-tapped primary of a small transformer (9) having a high-voltage center-tapped secondary. The vibrator introduces an alternating low-voltage potential into the primary and mechanically produces full-wave, rectified, pulsating, direct current from the secondary. A buffing condenser (11) across the secondary gives the proper wave form for long vibrator life: a resistor (12) its in series with this condenser across the total secondary to protect the transformer in case of• failure .of this capacitor. A voltage divider (10) with an adjustable slider permits accurate adjustment of the potential applied to the high-capacity firing condenser (5)."

Oct 1, 1947

By Edmond Chin

Mineral production was of minor importance to the country's economy, and Bangladesh was not a ranking world producer of any mineral commodity in 1980. Natural gas was the most important mineral exploited, and reserves were sufficient to allow a significant increase in its use. A greater proportion of the domestic heat and electrical energy needs could be filled by increased production and distribution of natural gas. Also, the export of natural gas was feasible either by pipeline to India or in the form of liquefied natural gas (LNG). Some nonmetallic minerals could be developed, as well as coal and peat, given sufficient capital investment. Bangladesh's strongly agricultural economy made fair progress in 1979.80.1 The major harvest of November-December 1979 turned out to be better than had been anticipated after an early drought left poor planting conditions. Secondary crops (harvested in February-March 1980 and June- July 1980) were excellent. There were prospects for a record harvest in fiscal year

Jan 1, 1982

By Charles C. Boley

The Bureau of Mines dried and carbonized two wood wastes, one softwood (redwood) and one hardwood (oak), using continuous, vertical entrainment techniques previously developed for use with coal. It was demonstrated that these techniques are readily applicable to wood waste and that appreciable changes in the yields of carbonization products can be obtained by varying operating conditions. A limited amount of experimental work was done on briquetting the char-coals. Firm briquets were formed with oak charcoal, although greater quantities of starch binder than used commercially for kiln-produced charcoal were required. Redwood charcoal did not briquet successfully under the test conditions employed.

Jan 1, 1969

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By William D. Mayercheck, August J. Kwitowski, John R. Bartels

This report discusses the Bureau of Mines' efforts to develop partial protective structures for operators of low-coal shuttle cars. In coal seams 48 in high or less, full-coverage canopies are generally difficult or may be impossible to implement on high-speed face equipment due to the restrictions they impose on the operator's vision and comfort. Lim- ited coverage is one alternative that provides an acceptable level of operator protection in thin-seam applications where conventional full- coverage canopies cannot be used. Three possible limited-coverage de- sign scenarios (roll bars, sliding canopies, and flip-top canopies) were designed, fabricated, and evaluated for low-coal shuttle cars. All three designs were determined to be feasible and desirable for low-coal shuttle car application.

Jan 1, 1987