Search Documents

By John D. Prater

Thallium is one of the rarer metals that has come into commercial importance in recent years. Although the element was first reported by Crookes in seleniferous deposits in lead chambers of a sulfuric acid plant in the Harz Mountains of Germany, it had no commercial significance until about 190O because of the high cost of extraction. Thallium occurs widely in the earth's crust but is found in such low concentrations that it is recovered only as a byproduct from processing other elements. There are no domestic ores of thallium; the entire output in this country is supplied by the American Smelting & Refining Co. as a byproduct of its cadmium operations at Globe, Colo. Thallium also is recovered from the flue dusts of sulfuric acid works in which thallium-bearing materials are used and as a byproduct of the lithopone industry. This paper describes methods for recovery of thallium from 'white arsenic" and lead Cottrell-precipitator dust of the American Smelting & Refining Co., lead smelter, Murray, Utah. Owing to an enlarged market for thallium because of increased military requirements and expanded peacetime uses, the Salt Lake Station of the Bureau of Mines surveyed the occurrence of thallium in ores, concentrates, and smelter products from all parts of the nation and found the most promising source was certain smelter products of the American Smelting & Refining Co. plant, Murray, Utah. Much of the thallium was being lost in marketed arsenic products; therefore, this investigation was undertaken to develop methods for recovering the thallium.

Jan 1, 1952

By A. J. Barry

Five makes of expansion-type shells and two types of bolts (mild-steel and high-strength) were used in 30 tests made in sandstone and shale roof, The results show that the anchorage obtained in both the sandstone and shale were stronger than either type of bolt. That is, the yield loads of both bolt types were exceeded before excessive anchor slip occurred. A relationship for evaluating the anchorage effectiveness of 3/8-inch-diameter, expansion-type bolts is presented. A comparison of test results indicates that the anchorage effectiveness of 5/8-inch- and 3/4-inch-diameter expansion-type bolts did not differ appreciably.

Jan 1, 1957

By P. C. Good

Tungsten metal in fused form and of high purity was prepared by reducing tungstic oxide with redistilled calcium metal in a heavy-walled sealed reactor. Alloys of tungsten with vanadium, molybdenum) chromium, columbium, and tantalum were prepared by coreduction of mixed metal oxides in the same manner. This work was undertaken by the Bureau of Mines to investigate new approaches for preparing tungsten and its alloys in high-purity form. The standard method of producing tungsten metal has been the reduction of tungstic oxides by hydrogen. The resulting metal powder is compacted, sintered, and fabricated by powder metallurgy methods. Long experience in this field has resulted in the development of a technology that (by careful control of the variables such as metal composition, particle size, and sinterng technique) is well adapted to producing wire and the small shapes usually prepared from tungsten metal.

Jan 1, 1961

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008, "I guess that without the occasional complaint, your mine is probably over-ventilated" (Marks, 2008). Miners are seldom in this situation and spend much of the time trying to find enough air to keep an operation running. With examination, there are usually changes that can be made to increase the efficiency of ventilation systems. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Modifications that result in surplus mine ventilation air could bring financial and environmental benefits. Some issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and nonmetal mines, to ventilate reserves that are deeper, hotter, and further away from fans and shafts, and to meet demands from increased production. This paper discusses successful methods to find additional usable air when there is no extra ventilation capacity. Most of the options presented in this paper are useful for metal/ nonmetal operations but some may be applicable to coal as well.

Jan 1, 2010

By Thomas M. Kohler, Gerald L. Finfinger, Gregory M. Molinda

The Bureau of Mines has completed an investigation of the effectiveness of methane drainage in the Lower Sunnyside Coalbed at Kaiser Steel Corp.'s Sunnyside No. 1 Mine in Utah. Most of the previous at- tempts to drain methane gas using long horizontal holes were conducted in the Eastern Coal Province. From the high degree of success realized in these efforts and the large body of knowledge gained from associated research, it seemed natural to extend the technology to western coalfields. Previous work had indicated that properties affecting gas drainage were variable in the Sunnyside Coalbed. In an attempt to characterize these properties, four degasification holes were drilled from the out- side entries of an advancing section. The holes were drilled to lengths of 780, 1,680, 1,315, and 1,047 ft and produced initial flow rates of 50,000, 180,000, 340,000, and 240,000 f t3/d, respectively. A total of over 300 million f t3 of commercial-quality gas has been removed from the Sunnyside Coalbed. The four holes have reduced face emissions by 78 pct.

Jan 1, 1986

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By Gregory Krohn

This report investigates the effects of adding a layer of extra padding to the palm area of leather gloves typically worn by low seam coal miners. The first study showed that added glove padding provides more potential protection but does not affect manual dexterity. The second study, in a simulated low seam coal mine, showed no significant differences using padded and non-padded gloves in crawling, shoveling, timbering, and cart pushing task completion times. In general, subjects preferred the padded gloves although they expressed some complaints about awkardness and loss of sensitivity. Recommendations are given for the design of padded gloves that will provide comfort, protection, and maximum hand sensitivity for miners.

Jan 1, 1980

By J. T. McCartney

"INTRODUCTION The surface areas of the finest fractions of a pulverized material are disproportionately larger than their weights. For instance, Pesrott and Kinney 3/ showed that, in a sample of minus 200-mesh coal, particles that are about 2 microns in diameter represent 15 percent of the entire surface area but only 1.5 percent of the total weight. Because the sur- face area is the dominating factor in the behavior of finely divided materials in many practical processes, the role of the finest particles is of great importance. The oxidation and combustion of pulverized coal, both in the dry form and in suspension in oils, and the hydrogenation to fluid hydrocarbons of mixtures of pulverized coal and heavy oil are reactions in which the surface area of the coal particles has considerable influence. This investigation of the size distribution of fine coal particles was conducted with the hope that such processes would thereby be better understood. The results should also be of value in the study of the crushing and fracture of coal."

Sep 1, 1945

By C. J. Cohen, L. A. Dahners

"SUMMARYA method has been developed for surveying, drill holes without lowering into the hole any surveying equipment other than an etch tube. The orientation of the rods at the collar of the hole is maintained as the etch tube is lowered. The attitude of the etch ellipse in depth with respect to the rod orientation at the collar can then be observed. This relationship permits the bearing of the hole in depth to he calculated. The rod orientation is maintained during the lowering by means of a pair of alinement clamps. One clamp is fastened to the top of each rod as the rod is coupled and is removed when the alinement has been transferred to the other clamp at the top of the next succeeding rod. A particular advantage of this survey technique is that surveys can be readily made in magnetic country rock.PRINCIPLE OF THE TECHNIQUEAn axial lamina of the column of drill roes is the lamina in which one fiber would be the centerline of the rods. In the new survey technique, the rods are fed into the hole in such a manner that the axial lamina of each successive rod maintains its position at the collar of the hole. In depth, as the rods bend in following the drill hole, the axial laminae also bend. The lamina that was originally vertical will, in general, be tilted away from the vertical. The trace of this lamina is marked on the glass etch tube before the tube is lowered in the hole. The axial lamina that becomes vertical at the survey station is recognized as that axial lamina which contains the long axis of the etch ellipse. The angle between the lamina originally vertical and the lamina vertical at the survey station is thus measurable. When the vertical axial lamina at one survey station has been determined by the etch ellipse at that station, angle R between this lamina and the vertical axial lamina at the next survey station becomes measurable also. By moans of angle R, and dip angles D1 and D2 at the two stations, the change in bearing (z) of the drill hole between the two stations can be calculated."

Aug 1, 1944

By Kenneth Lipman

Auxiliary equipment was assembled around a purchased oscillograph to permit observation of the current and voltage characteristics of low-energy, capacitance-discharge sparks having durations of at least 10 mµ-sec. Circuit details of the assembled apparatus, performance characteristics of the complete system, and some preliminary data from representative self-initiated sparks are given in this report. INTRODUCTION One of the subjects of continuing research by the Federal Bureau of Mines Division of Explosives Technology is the ignition of explosive-gas mixtures by means of low-energy capacitance sparks. Quite early in these investigations it was recognized that understanding the gas-ignition phenomena would be facilitated by detailed information about the performance of the ignition source (spark) under the actual conditions of interest; however, the sparks of practical interest are nonrepetitive transient phenomena whose duration could reasonably be estimated to be in the time range of 1 mµsec. to 1 µsec. As such, the only feasible method of obtaining detailed information was and is oscillographic representation of the pertinent current and voltage transients. It was not until 1947 that a suitable, commercial, dual-channel oscillograph could be obtained as the basic instrument for these studies; the instrument specified in 1947 was delivered in 1950. This paper describes the auxiliary

Jan 1, 1959

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By Kevin Ashley

Because toxicities may differ for Cr(VI) compounds of varying solubility, some countries and organizations have promulgated different occupational exposure limits (OELs) for soluble and insoluble hexavalent chromium (Cr(VI)) compounds, and analytical methods are needed to determine these species in workplace air samples. To address this need, international standard methods ASTM D6832 and ISO 16740 have been published that describe sequential extraction techniques for soluble and insoluble Cr(VI) in samples collected from occupational settings. However, no published performance data were previously available for these Cr(VI) sequential extraction procedures. In this work, the sequential extraction methods outlined in the relevant international standards were investigated. The procedures tested involved the use of either deionized water or an ammonium sulfate/ ammonium hydroxide buffer solution to target soluble Cr(VI) species. This was followed by extraction in a sodium carbonate/sodium hydroxide buffer solution to dissolve insoluble Cr(VI) compounds. Three-step sequential extraction with (1) water, (2) sulfate buffer and (3) carbonate buffer was also investigated. Sequential extractions were carried out on spiked samples of soluble, sparingly soluble and insoluble Cr(VI) compounds, and analyses were then generally carried out by using the diphenylcarbazide method. Similar experiments were performed on paint pigment samples and on airborne particulate ?lter samples collected from stainless steel welding. Potential interferences from soluble and insoluble Cr(III) compounds, as well as from Fe(II), were investigated. Interferences from Cr(III) species were generally absent, while the presence of Fe(II) resulted in low Cr(VI) recoveries. Two-step sequential extraction of spiked samples with (?rst) either water or sulfate buffer, and then carbonate buffer, yielded quantitative recoveries of soluble Cr(VI) and insoluble Cr(VI), respectively. Three-step sequential extraction gave excessively high recoveries of soluble Cr(VI), low recoveries of sparingly soluble Cr(VI), and quantitative recoveries of insoluble Cr(VI). Experiments on paint pigment samples using two-step extraction with water and carbonate buffer yielded varying percentages of relative fractions of soluble and insoluble Cr(VI). Sequential extractions of stainless steel welding fume air ?lter samples demonstrated the predominance of soluble Cr(VI) compounds in such samples. The performance data obtained in this work support the Cr(VI) sequential extraction procedures described in the international standards.

Jan 1, 2009

By McHenry Mosier

Diamond -drilling blast holes at Eastern Magnetite Mine C is proving economical in boundary shrinks , in removing pillars not readily accessible for percussion drilling , and in driving scraper drifts . The cost per foot drilled is greater than for percussion drilling , but savings in associated factors outweigh this handicap . The rocks drilled include trap rock and magnetite ore . The mining method is the panel , block- caving system utilizing scraper sublevel drifts instead of branch raises to convey the ore to the haulage level . Diamond -drilling blast holes was begun early in 1945. Three rigs equipped with noncoring bits are now in active operation two shifts per day . They are owned by the company , and the drill operators are paid by the day . In shrinkage stopes the drill is mounted on a horizontal bar set against opposite walls of the stope . Stoping holes are horizontal , which gives better results in blasting and requires fewer set ups . In scraper drifts the drill is mounted on a horizontal bar clamped to two columns about feet apart . Trim holes around the periphery of the drift and reliever holes are drilled 50 to 80 feet in length . A 10 - foot wedge cut drilled with a stoper is blasted in conjunction with a corresponding length of the trim holes to effect a 10 -foot advance of the full- sized drift . Recent drilling averages 97 feet per machine shift , excluding time utilized in setting up and moving the machine , hand mucking , and barring down . The feet drilled per bit at present is 417. These data represent the average for drilling in both rock (waste) and ore . Percussion drilling utilizes three types of wet drills . Detachable bits are standard . Gage changes for new bits is 1/8 inch and for reconditioned bits 1/16 inch . The life of a bit is five uses . Resharpening is on contract . A drill carriage is used in haulage headings .

Feb 1, 1948

By R. F. Abernethy

A modified Unterzaucher method was applied to the direct determination of oxygen in coal. Coal samples were pyrolyzed in a nitrogen atmosphere, and the gaseous oxygen compounds liberated were converted to carbon monoxide by a platinized-carbon catalyst at 9000 C. After passing over heated copper and through a tube containing soda-asbestos and magnesium perchlorate, the purified carbon monoxide was oxidized to carbon dioxide by iodine pentoxide--liberating an equivalent amount of iodine. The iodine was titrated with 0.02 ~ sodium thiosulfate; in a few tests the weight of carbon dioxide produced was determined. Direct oxygen determinations of coal included organic oxygen from the coal substance, plus a small quantity of inorganic oxygen derived principally from carbonate minerals and from combined water of silicates in the mineral matter. The influence of mineral matter on the direct oxygen determination was investigated by testing (1) untreated coal, (2) demineralized coal from which most of the mineral matter except pyrite was removed by treatment with hydrofluoric and hydrochloric acids, and (3) coal samples treated with dilute hydrochloric acid.

Jan 1, 1966

By Oliver Bowles

Since 1922 when the Bureau of Mines issued a report2 covering the slate industry in detail, changes in technology have taken place which have an important bearing on the industry. The present paper comprises a record of these changes. Though the value of slate, for roofing, structural, blackboard, sanitary, and electrical uses is generally recognized, it has many competitors. To meet this constantly increasing competition producers are promoting economies in manufacture, and improving processes, thereby lessening costs of production, and are placing on the market products of the highest possible quality, thus creating satisfaction and confidence on the part of the user. This endeavor to place the industry on a better basis, both as regards processes and products, is shown in the recent developments in technology which are presented herein. Valuable assistance in obtaining data for this paper was given by W. S. Hays, secretary of the National Slate Association, N. M. Male, president of the National Slate Association, and Robert Notvest, consulting engineer, Cleveland, O.

Jan 1, 1926

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By Robert J. Timko

Because of leakage through and around permanent stoppings in underground mines, more air must be forced into a mine than would otherwise be required for ventilation. As power costs increase, costs resulting from air leakage add increasingly to the operating costs of mining. The Bureau of Mines evaluated four different stopping construction techniques based on the ideas that (1) airtightness could be enhanced by brushing rather than troweling on mortar sealant and that (2) modified mortars (mortars containing glass fibers and other additives for increased strength and adhesion) would improve sealing performance. Air leakage tests comparing conventional to modified stoppings were done when the stoppings were built, after 6 months, after 1 yr, and following simple maintenance. It was found that stoppings can be built and maintained better if-- The area where a stopping is to be built is properly prepared. Stoppings are constructed using the techniques devised by the Bureau. Stoppings are periodically examined for leaks. Stoppings found to be leaking, especially at the perimeters, are resealed.

Jan 1, 1983